Three filter beds for arsenite and chromate removal

Arsenic (As) and chromium (Cr) are two of the most toxic pollutants introduced into natural waters from a variety of sources, and they cause various adverse effects on living bodies when their concentrations exceed permissible limits. Laboratory experiments have been conducted to investigate the sorption of As and Cr on carbon steel and removal of trace elements from drinking water with a household filtration process. The affinity of As and Cr species for iron/iron carbide (Fe/Fe3C) sites is the key factor in controlling the removal of the elements. The method is based on the use of powder carbon steel, powdered block carbon, and ball ceramic in the ion-sorption columns as a cleaning process. The presence of carbon steel in a system that contains As3+ and Cr6+ might have a potential effect.

Removal of organic contaminants from wastewater using the electrodialytic process

Pharmaceuticals and personal care products (PPCPs) are widely used on a daily basis. After their usage they reach the wastewater treatment plants (WWTPs). These compounds have different physico-chemical characteristics, which makes them difficult to completely remove in the WWTPs, througth conventional treatments. Currently, there is no legislation regarding PPCPs thresholds in effluent discharge. But, even at vestigial concentrations, these compounds enclose environmental risks due to, e.g., endocrine disruption potential. There is a need of alternative techniques for their removal in WWTPs. The main goal of this work was to assess the use of electrodialytic (ED) process to remove PPCPs from the effluent to be discharged. A two-compartment ED cell was used testing (i) the effluent position in the cell (anode and cathode compartment); (ii) the use of anion (AEM) and cation exchange membrane (CEM); (iii) the treatment period (6, 12 and 24 hours); (iv) effluent recirculation and current steps; (v) the feasibility of sequential treatments. Phosphorus (P) removal from effluent and energetic costs associated to the process were also evaluated. Five PPCPs were studied – caffeine (CAF), bisphenol A (BPA), 17 β-estradiol (E2), ethinyl estradiol (EE2) and oxybenzone (MBPh). The ED process showed to be effective in the removal when effluent is in the anode compartment. Oxidation is suggested to be the main removal process, which was between 88 and 96%, for all the compounds, in 6 hours. Nevertheless, the presence of intermediates and/or by-products was also observed in some cases. Effluent recirculation should have a retention time in the ED cell big enough to promote removal whereas the current steps (effluent in anode compartment) slightly increased removal efficiencies (higher than 80% for all PPCPs). The sequential set of ED treatment (effluent in anode compartment) showed to be effective during both periods with a removal percentage between 80 and 95% and 73 to 88% in the case of AEM and CEM, respectively. Again, the main removal process is strongly suggested to be oxidation in the anode compartment. However, there was an increase of BOD5 and COD, which might be explained by effluent spiking, these parameters limiting the effluent discharge. From these treatments, the use of AEM, enhanced the P removal from effluent to minimize risk of eutrophication. Energetic costs of the best set-up (6 hours) are approximately 0,8€/m3 of wastewater, a value considered low, attending to the prices of other treatment processes.

Success of referral for alcohol dependent patients from a general hospital : predictive value of patient and process characteristics

RESUME: Introduction L'objectif de cette étude prospective de cohorte était d'estimer l'efficacité d'un processus de prise en charge standardisé de patients dépendants de l'alcool dans le contexte d'un hôpital universitaire de soins généraux. Ce modèle de prise en charge comprenait une évaluation multidisciplinaire puis des propositions de traitements individualisées et spécifiques (« projet thérapeutique »). Patients et méthode 165 patients alcoolo-dépendants furent recrutés dans différents services de l'hôpital universitaire, y compris la policlinique de médecine. Ils furent dans un premier temps évalués par une équipe multidisciplinaire (médecin interniste, psychiatre, assistant social), puis un projet thérapeutique spécialisé et individualisé leur fut proposé lors d'une rencontre réunissant le patient et l'équipe. Tous les patients éligibles acceptant de participer à l'étude (n=68) furent interrogés au moment de l'inclusion puis 2 et 6 mois plus tard par une psychologue. Des informations standardisées furent recueillies sur les caractéristiques des patients, le processus de prise en charge et l'évolution à 6 mois. Les critères de succès utilisés à 6 mois furent: l'adhérence au traitement proposé et l'abstinence d'alcool. Résultats Lors de l'évaluation à 6 mois, 43% des patients étaient toujours en traitement et 28% étaient abstinents. Les variables prédictrices de succès parmi les caractéristiques des patients étaient un âge de plus de 45 ans, ne pas vivre seul, avoir un travail et être motivé pour un traitement (RAATE-A <18). Pour les variables dépendantes du processus de prise en charge, un sevrage complet de l'alcool lors de la rencontre multidisciplinaire ainsi que la présence de tous les membres de l'équipe à cette réunion étaient des facteurs associés au succès. Conclusion L'efficacité de ce modèle d'intervention pour patients dépendants de l'alcool en hôpital de soins généraux s'est montrée satisfaisante, en particulier pour le critère de succès adhérence au traitement. Des variables associées au succès ou à l'échec à 6 mois ont pu être mises en évidence, permettant d'identifier des populations de patients évoluant différemment. Des stratégies de prise en charge tenant compte de ces éléments pourraient donc être développées, permettant de proposer des traitements plus adaptés ainsi qu'une meilleure rétention des patients alcooliques dans les programmes thérapeutiques. ABSTRACT. To assess the effectiveness of a multidisciplinary evaluation and referral process in a prospective cohort of general hospital patients with alcohol dependence, alcohol-dependent patients were identified in the wards of the general hospital and its primary care center. They were evaluated and then referred to treatment by a multidisciplinary team; those patients who accepted to participate in this cohort study were consecutively included and followed for 6 months. Not included patients were lost for follow-up, whereas all included patients were assessed at time of inclusion, 2 and 6 months later by a research psychologist in order to collect standardized baseline patients' characteristics, process salient features and patients outcomes (defined as treatment adherence and abstinence). Multidisciplinary evaluation and therapeutic referral was feasible and effective, with a success rate of 43% for treatment adherence and 28% for abstinence at 6 months. Among patients' characteristics, predictors of success were an age over 45, not living alone, being employed and being motivated to treatment (RAATE-A score < 18), whereas successful process characteristics included detoxification of the patient at time of referral and a full multidisciplinary referral meeting. This multidisciplinary model of evaluation and referral of alcohol dependent patients of a general hospital had a satisfactory level of effectiveness. Predictors of success and failure allow the identification of subsets of patients for whom new strategies of motivation and treatment referral should be designed.

Characterisation of Hydrophobic Nonfibrous Material and Its Removal From Pulp Suspension

Paperin ja kartongin kierrätys lisääntyy taloudellisten intressien ja ympäristöhygieenisten tavoitteiden takia jatkuvasti. Lisääntyvän kierrätyksen myötä myös paperin ja kartongin epäpuhtauksien määrä kasvaa, mikä huonontaa kierrätysraaka-aineen laatua. Tämän työn tarkoituksena on antaa perustietoa eräästä kartongin päällystyksessä käytettävästä hydrofobisesta materiaalista, epäpuhtaan kartongin kierrätyksestä sekä ongelmista, joita epäpuhtaan kartongin kierrätyksestä syntyy. Kierrätyskuidun fraktiointi on yksinkertainen prosessi aallotuskartongin, testilainerin ja taivekartongin valmistuksessa. Kierrätysprosessin ensisijaisia tehtäviä ovat kuidutus ja epäpuhtauksien poisto sekä näiden epäpuhtauksien vaikutusten eliminointi, jotta kierrätysmassan laatuvaatimukset täyttyvät. Lisääntynyt epäpuhtauksien määrä raaka-aineessa asettaa vaatimuksia lajitteluprosessin kehittämiseksi. Nykyaikaisilla kierrätyslaitoksilla ei pystytä käsittelemään ylettömiä määriä epäpuhtauksia. Epäpuhtaudet aiheuttavat ongelmia ajettavuuteen ja heikentävät tuotteen laatua kierrätysprosessissa. Epäpuhtauksien poistoon on olemassa useita teknisiä ratkaisuja, mutta minkään niistä ei ole todettu täysin poistavan kaikkia ongelmia. Työn kokeellisessa osassa kartongin päällystykseen käytettävää hydrofobista materiaalia analysoitiin erilaisin menetelmin. Tutkittiin myös erilaisten olosuhteiden vaikutusta tämän materiaalin poistoon.

Homogenization Dynamics and Introduction Routes of Invasive Freshwater Fish in the Iberian Peninsula

Nonnative invasive species are one of the main global threats to biodiversity. The understanding of the traits characterizing successful invaders and invasion-prone ecosystems is increasing, but our predictive ability is still limited. Quantitative information on biotic homogenization and particularly its temporal dynamics is even scarcer. We used freshwater fish distribution data in the Iberian Peninsula in four periods (before human intervention, 1991, 1995, and 2001) to assess the temporal dynamics of biotic homogenization among river basins. The percentage of introduced species among fish faunas has increased in recent times (from 41.8% in 1991 to 52.5% in 2001), leading to a clear increase in the similarity of community composition among basins. The mean Jaccard's index increase (a measure of biotic homogenization) from the pristine situation to the present (17.1%) was similar to that for Californian fish but higher than for other studies. However, biotic homogenization was found to be a temporally dynamic process, with finer temporal grain analyses detecting transient stages of biotic differentiation. Introduced species assemblages were spatially structured along a latitudinal gradient in the Iberian Peninsula, with species related to sport fishing being characteristic of northern basins. Although the comparison of fish distributions in the Iberian Peninsula and France showed significant and generalized biotic homogenization, nonnative assemblages of northeastern Iberian basins were more similar to those of France than to those of the rest of the Iberian Peninsula, indicating a main introduction route. Species introduced to the Iberian Peninsula tended to be mainly piscivores or widely introduced species that previously had been introduced to France. Our results indicate that the simultaneous analysis of the spatial distribution of introduced assemblages (excluding native species that reflect other biogeographical patterns) and their specific traits can be an effective tool to detect introduction and invasion routes and to predict future invaders from donor regions

Introduction to Game Design and Development

This is the introductory lecture to COMP3218. We introduce ourselves, cover the philosophy of the course, the structure and assessment process, and lead an initial game design exercise.

Autogenous transplantation of rib cartilage preserved in glycerol, after removal of the perichondrium, to the malar process of rats--a histological study (Part I).

Seventy-two male albino rats received autogenous transplants of glycerol-preserved rib cartilage into the malar process. The animals were divided into two groups which received preserved cartilage with or without perichondrium. The implants were well tolerated and removal of the perichondrium enhanced the rate of resorption and bone replacement of the material.

Phytotherapy: an introduction to its history, use and application

There has been a great advance in the pharmacognosy field, which has increased the use of medicinal plants by health professionals and practitioners of folk medicine. This systematic review explored the history and the present day application of phytotherapeutic medicines. We searched the databases Cochrane Library, Embase, Lilacs, PubMed, Scielo and a specialized bibliography. We concluded that there are many therapeutic potentialities in the use of phytotherapeutic medicines and medicinal plants. We also concluded that despite the increasing number of publications in the field each year, there is still a lack of reviews and meta-analyses that could promote a better integration of the knowledge produced. In addition, research about pharmacological interactions and multidisciplinary studies may promote a quicker and safer process from the workbench up to the clinical trials.

Bioremediation of PAHs - Limitations and soultions

Introduction 1.1 Occurrence of polycyclic aromatic hydrocarbons (PAH) in the environment Worldwide industrial and agricultural developments have released a large number of natural and synthetic hazardous compounds into the environment due to careless waste disposal, illegal waste dumping and accidental spills. As a result, there are numerous sites in the world that require cleanup of soils and groundwater. Polycyclic aromatic hydrocarbons (PAHs) are one of the major groups of these contaminants (Da Silva et al., 2003). PAHs constitute a diverse class of organic compounds consisting of two or more aromatic rings with various structural configurations (Prabhu and Phale, 2003). Being a derivative of benzene, PAHs are thermodynamically stable. In addition, these chemicals tend to adhere to particle surfaces, such as soils, because of their low water solubility and strong hydrophobicity, and this results in greater persistence under natural conditions. This persistence coupled with their potential carcinogenicity makes PAHs problematic environmental contaminants (Cerniglia, 1992; Sutherland, 1992). PAHs are widely found in high concentrations at many industrial sites, particularly those associated with petroleum, gas production and wood preserving industries (Wilson and Jones, 1993). 1.2 Remediation technologies Conventional techniques used for the remediation of soil polluted with organic contaminants include excavation of the contaminated soil and disposal to a landfill or capping - containment - of the contaminated areas of a site. These methods have some drawbacks. The first method simply moves the contamination elsewhere and may create significant risks in the excavation, handling and transport of hazardous material. Additionally, it is very difficult and increasingly expensive to find new landfill sites for the final disposal of the material. The cap and containment method is only an interim solution since the contamination remains on site, requiring monitoring and maintenance of the isolation barriers long into the future, with all the associated costs and potential liability. A better approach than these traditional methods is to completely destroy the pollutants, if possible, or transform them into harmless substances. Some technologies that have been used are high-temperature incineration and various types of chemical decomposition (for example, base-catalyzed dechlorination, UV oxidation). However, these methods have significant disadvantages, principally their technological complexity, high cost , and the lack of public acceptance. Bioremediation, on the contrast, is a promising option for the complete removal and destruction of contaminants. 1.3 Bioremediation of PAH contaminated soil & groundwater Bioremediation is the use of living organisms, primarily microorganisms, to degrade or detoxify hazardous wastes into harmless substances such as carbon dioxide, water and cell biomass Most PAHs are biodegradable unter natural conditions (Da Silva et al., 2003; Meysami and Baheri, 2003) and bioremediation for cleanup of PAH wastes has been extensively studied at both laboratory and commercial levels- It has been implemented at a number of contaminated sites, including the cleanup of the Exxon Valdez oil spill in Prince William Sound, Alaska in 1989, the Mega Borg spill off the Texas coast in 1990 and the Burgan Oil Field, Kuwait in 1994 (Purwaningsih, 2002). Different strategies for PAH bioremediation, such as in situ , ex situ or on site bioremediation were developed in recent years. In situ bioremediation is a technique that is applied to soil and groundwater at the site without removing the contaminated soil or groundwater, based on the provision of optimum conditions for microbiological contaminant breakdown.. Ex situ bioremediation of PAHs, on the other hand, is a technique applied to soil and groundwater which has been removed from the site via excavation (soil) or pumping (water). Hazardous contaminants are converted in controlled bioreactors into harmless compounds in an efficient manner. 1.4 Bioavailability of PAH in the subsurface Frequently, PAH contamination in the environment is occurs as contaminants that are sorbed onto soilparticles rather than in phase (NAPL, non aqueous phase liquids). It is known that the biodegradation rate of most PAHs sorbed onto soil is far lower than rates measured in solution cultures of microorganisms with pure solid pollutants (Alexander and Scow, 1989; Hamaker, 1972). It is generally believed that only that fraction of PAHs dissolved in the solution can be metabolized by microorganisms in soil. The amount of contaminant that can be readily taken up and degraded by microorganisms is defined as bioavailability (Bosma et al., 1997; Maier, 2000). Two phenomena have been suggested to cause the low bioavailability of PAHs in soil (Danielsson, 2000). The first one is strong adsorption of the contaminants to the soil constituents which then leads to very slow release rates of contaminants to the aqueous phase. Sorption is often well correlated with soil organic matter content (Means, 1980) and significantly reduces biodegradation (Manilal and Alexander, 1991). The second phenomenon is slow mass transfer of pollutants, such as pore diffusion in the soil aggregates or diffusion in the organic matter in the soil. The complex set of these physical, chemical and biological processes is schematically illustrated in Figure 1. As shown in Figure 1, biodegradation processes are taking place in the soil solution while diffusion processes occur in the narrow pores in and between soil aggregates (Danielsson, 2000). Seemingly contradictory studies can be found in the literature that indicate the rate and final extent of metabolism may be either lower or higher for sorbed PAHs by soil than those for pure PAHs (Van Loosdrecht et al., 1990). These contrasting results demonstrate that the bioavailability of organic contaminants sorbed onto soil is far from being well understood. Besides bioavailability, there are several other factors influencing the rate and extent of biodegradation of PAHs in soil including microbial population characteristics, physical and chemical properties of PAHs and environmental factors (temperature, moisture, pH, degree of contamination). Figure 1: Schematic diagram showing possible rate-limiting processes during bioremediation of hydrophobic organic contaminants in a contaminated soil-water system (not to scale) (Danielsson, 2000). 1.5 Increasing the bioavailability of PAH in soil Attempts to improve the biodegradation of PAHs in soil by increasing their bioavailability include the use of surfactants , solvents or solubility enhancers.. However, introduction of synthetic surfactant may result in the addition of one more pollutant. (Wang and Brusseau, 1993).A study conducted by Mulder et al. showed that the introduction of hydropropyl-ß-cyclodextrin (HPCD), a well-known PAH solubility enhancer, significantly increased the solubilization of PAHs although it did not improve the biodegradation rate of PAHs (Mulder et al., 1998), indicating that further research is required in order to develop a feasible and efficient remediation method. Enhancing the extent of PAHs mass transfer from the soil phase to the liquid might prove an efficient and environmentally low-risk alternative way of addressing the problem of slow PAH biodegradation in soil.

Analysis of the introduction of a business process mapping system in Rosetti Marino spa

After a first theoric introduction about Business Process Re-engineering (BPR), are considered in particular the possible options found in literature regarding the following three macro-elements: the methodologies, the modelling notations and the tools employed for process mapping. The theoric section is the base for the analysis of the same elements into the specific case of Rosetti Marino S.p.A., an EPC contractor, operating in the Oil&Gas industry. Rosetti Marino implemented a tool developped internally in order to satisfy its needs in the most suitable way possible and buit a Map of all business processes,navigable on the Company Intranet. Moreover it adopted a methodology based upon participation, interfunctional communication and sharing. The GIGA introduction is analysed from a structural, human resources, political and symbolic point of view.

Privatization in Bosnia and Herzegovina: Insights from and into the craft of interorganizational process analysis.

International efforts to help Bosnia and Herzegovina privatize its state-owned enterprises proved dif.cult, but the complex web of interorganizational relationships (IORs) among international donors, implementers, contractors, and local players, at times, seemed even more daunting to effective implementation of reforms than the technical dif.culties of the task itself. By employing a theoretical framework of IOR development over time, important stages in the evolution of the International Advisory Group on Privatization were identi.ed, and variables within each discussed. Analysis employed linear and nonlinear process logics to help explain what linked some variables withinand betweenthese various phases. Insights seemed valuable for practitioners seeking to implement interdependent tasks, organizational representatives trying to form relationships with others, and scholars trying to understand process theories of IOR formation. In addition, this research provides an introduction to the complexities of international development assistance — a crucially important and under-researched arena.

Plasma delipidation process induces rapid regression of atherosclerosis and mobilisation of adipose tissue

Cholesterol is a major component of atherosclerotic plaques. Cholesterol accumulation within the arterial intima and atherosclerotic plaques is determined by the difference of cellular cholesterol synthesis and/or influx from apo B-containing lipoproteins and cholesterol efflux. In humans, apo A-I Milano infusion has led to rapid regression of atherosclerosis in coronary arteries. We hypothesised that a multifunctional plasma delipidation process (PDP) would lead to rapid regression of experimental atherosclerosis and probably impact on adipose tissue lipids. In hyperlipidemic animals, the plasma concentrations of cholesterol, triglyceride and phospholipid were, respectively, 6-, 157-, and 18-fold higher than control animals, which consequently resulted in atherosclerosis. PDP consisted of delipidation of plasma with a mixture of butanol-diisopropyl ether (DIPE). PDP removed considerably more lipid from the hyperlipidemic animals than in normolipidemic animals. PDP treatment of hyperlipidemic animals markedly reduced intensity of lipid staining materials in the arterial wall and led to dramatic reduction of lipid in the adipose tissue. Five PDP treatments increased apolipoprotein A1 concentrations in all animals. Biochemical and hematological parameters were unaffected during PDP treatment. These results show that five PDP treatments led to marked reduction in avian atherosclerosis and removal of lipid from adipose tissue. PDP is a highly effective method for rapid regression of atherosclerosis.

Apoptotic cell removal in development and tissue homeostasis

Cell deletion is a physiological process for the development and maintenance of tissue homeostasis in metazoa. This is mainly achieved by the induction of various forms of programmed cell death followed by the recognition and removal of the targeted cells by phagocytes. In this review, we will discuss cell deletion in relation to the development and function of the innate immune system, particularly of the mononuclear phagocyte system (MPS), its ontogeny and potential role in tissue remodeling in the embryo and adult. Ongoing studies are addressing the roles of professional phagocytes of the MPS and neighboring tissue cells in dying cell removal, and candidate molecules that might attract mononuclear phagocytes to the dying cells. The potential phagocyte must discriminate between living and dying cells; current concepts for this discrimination derive from the observation of newly exposed ligands on the dying cells and new evidence for direct inhibition of uptake by viable cells.

Directions for a troubled discipline:strategy research, teaching and practice introduction to the dialog

This Dialog responds to a growing debate about the relevance of business schools generally and the value of strategy theory and research for strategic management practice. The authors propose that academic theory and management practice can be better connected through management education. The academy researches practice, derives theory, and returns it to practice through the development of teaching materials and the teaching of current and future practitioners. The three articles in this Dialog examine how different approaches to strategy research inform strategy teaching and its application to practice. Joseph Bower explains the rise of business policy and the process research approach that informed that teaching tradition at Harvard Business School. Robert Grant responds by emphasizing the economic theory underpinnings of strategic management research and its impact on teaching. Paula Jarzabkowski and Richard Whittington conclude by proposing a strategyas-practice perspective and suggesting ways to better incorporate strategy-as-practice research into strategy teaching.

Introduction : the role of quality, production and technological innovation in improving competitive performance

Quality, production and technological innovation management rank among the most important matters of concern to modern manufacturing organisations. They can provide companies with the decisive means of gaining a competitive advantage, especially within industries where there is an increasing similarity in product design and manufacturing processes. The papers in this special issue of International Journal of Technology Management have all been selected as examples of how aspects of quality, production and technological innovation can help to improve competitive performance. Most are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the theme was 'Getting Ahead Through Technology and People'. At the conference itself over 80 papers were presented by authors from 15 countries around the world. Among the many topics addressed within the conference theme, technological innovation, quality and production management emerged as attracting the greatest concern and interest of delegates, particularly those from industry. For any new initiative to be implemented successfully, it should be led from the top of the organization. Achieving the desired level of commitment from top management can, however, be a difficulty. In the first paper of this issue, Mackness investigates this question by explaining how systems thinking can help. In the systems approach, properties such as 'emergence', 'hierarchy', 'commnication' and 'control' are used to assist top managers in preparing for change. Mackness's paper is then complemented by Iijima and Hasegawa's contribution in which they investigate the development of Quality Information Management (QIM) in Japan. They present the idea of a Design Review and demonstrate how it can be used to trace and reduce quality-related losses. The next paper on the subject of quality is by Whittle and colleagues. It relates to total quality and the process of culture change within organisations. Using the findings of investigations carried out in a number of case study companies, they describe four generic models which have been identified as characterising methods of implementing total quality within existing organisation cultures. Boaden and Dale's paper also relates to the management of quality, but looks specifically at the construction industry where it has been found there is still some confusion over the role of Quality Assurance (QA) and Total Quality Management (TQM). They describe the results of a questionnaire survey of forty companies in the industry and compare them to similar work carried out in other industries. Szakonyi's contribution then completes this group of papers which all relate specifically to the question of quality. His concern is with the two ways in which R&D or engineering managers can work on improving quality. The first is by improving it in the laboratory, while the second is by working with other functions to improve quality in the company. The next group of papers in this issue all address aspects of production management. Umeda's paper proposes a new manufacturing-oriented simulation package for production management which provides important information for both design and operation of manufacturing systems. A simulation for production strategy in a Computer Integrated Manufacturing (CIM) environment is also discussed. This paper is then followed by a contribution by Tanaka and colleagues in which they consider loading schedules for manufacturing orders in a Material Requirements Planning (MRP) environment. They compare mathematical programming with a knowledge-based approach, and comment on their relative effectiveness for different practical situations. Engstrom and Medbo's paper then looks at a particular aspect of production system design, namely the question of devising group working arrangements for assembly with new product structures. Using the case of a Swedish vehicle assembly plant where long cycle assembly work has been adopted, they advocate the use of a generally applicable product structure which can be adapted to suit individual local conditions. In the last paper of this particular group, Tay considers how automation has affected the production efficiency in Singapore. Using data from ten major industries he identifies several factors which are positively correlated with efficiency, with capital intensity being of greatest interest to policy makers. The two following papers examine the case of electronic data interchange (EDI) as a means of improving the efficiency and quality of trading relationships. Banerjee and Banerjee consider a particular approach to material provisioning for production systems using orderless inventory replenishment. Using the example of a single supplier and multiple buyers they develop an analytical model which is applicable for the exchange of information between trading partners using EDI. They conclude that EDI-based inventory control can be attractive from economic as well as other standpoints and that the approach is consistent with and can be instrumental in moving towards just-in-time (JIT) inventory management. Slacker's complementary viewpoint on EDI is from the perspective of the quality relation-ship between the customer and supplier. Based on the experience of Lucas, a supplier within the automotive industry, he concludes that both banks and trading companies must take responsibility for the development of payment mechanisms which satisfy the requirements of quality trading. The three final papers of this issue relate to technological innovation and are all country based. Berman and Khalil report on a survey of US technological effectiveness in the global economy. The importance of education is supported in their conclusions, although it remains unclear to what extent the US government can play a wider role in promoting technological innovation and new industries. The role of technology in national development is taken up by Martinsons and Valdemars who examine the case of the former Soviet Union. The failure to successfully infuse technology into Soviet enterprises is seen as a factor in that country's demise, and it is anticipated that the newly liberalised economies will be able to encourage greater technological creativity. This point is then taken up in Perminov's concluding paper which looks in detail at Russia. Here a similar analysis is made of the concluding paper which looks in detail at Russia. Here a similar analysis is made of the Soviet Union's technological decline, but a development strategy is also presented within the context of the change from a centralised to a free market economy. The papers included in this special issue of the International Journal of Technology Management each represent a unique and particular contribution to their own specific area of concern. Together, however, they also argue or demonstrate the general improvements in competitive performance that can be achieved through the application of modern principles and practice to the management of quality, production and technological innovation.