Modificação superficial do tecido 100% algodão tratado com plasma

The 100% cotton fabric (CO)* treated with plasma of methane CH4 has direct application in all areas that needs of aqueous solutions repellent material like coatings and uniforms applied biomedical, aeronautics, and automobile between others. 100% cotton fabric (CO) samples were treated by plasma with two differents atmosphere: Methane gas (CH4), treatment time was varied in 10 in 10 min. until 60 min., and mixture methane/argon (CH4/Ar), it was varied the proportion 1:9, 2:8, 3:7, 4:6, 5:5, 6:4, 7:3, 8:2 e 9:1, with treatment time of 30 minutes. In both, the fluxe was 5 sccm (second cubic centimeter), pressure 6 mbar, voltage 490 V and current 0,15A. The objective of work was measure the superficial tension of 100% CO then it treated with plasma, using contact angle measures of water and glycerol with the surface. The samples were tested after treatment, with 8 and 12 months to verify the superficial modification effects. It was verified an increase of hydrophobility with the Sessile drop values varied between 116,69º to 137,85º and it carried on after 12 months. The no treated samples shows contact angle equal 0º. OES analysis and Raman spectroscopy were accomplished. In the SEM analysis was verified oligomers. The plasma treatment is correct environmental, It turning greater than conventional treatments

Análise aerodinâmica de perfis de asa para aeronaves experimentais tipo jn-1

The great importance in selecting the profile of an aircraft wing concerns the fact that its relevance in the performance thereof; influencing this displacement costs (fuel consumption, flight level, for example), the conditions of flight safety (response in critical condition) of the plane. The aim of this study was to examine the aerodynamic parameters that affect some types of wing profile, based on wind tunnel testing, to determine the aerodynamic efficiency of each one of them. We compared three types of planforms, chosen from considerations about the characteristics of the aircraft model. One of them has a common setup, and very common in laboratory classes to be a sort of standard aerodynamic, it is a symmetrical profile. The second profile shows a conFiguration of the concave-convex type, the third is also a concave-convex profile, but with different implementation of the second, and finally, the fourth airfoil profile has a plano-convex. Thus, three different categories are covered in profile, showing the main points of relevance to their employment. To perform the experiment used a wind tunnel-type open circuit, where we analyzed the pressure distribution across the surface of each profile. Possession of the drag polar of each wing profile can be, from the theoretical basis of this work, the aerodynamic characteristics relate to the expected performance of the experimental aircraft, thus creating a selection model with guaranteed performance aerodynamics. It is believed that the philosophy used in this dissertation research validates the results, resulting in an experimental alternative for reliable implementation of aerodynamic testing in models of planforms

Estudo das interações polifenol-proteína e das reações de escurecimento não-enzimático para o processamento de cajuína

The cashew, a fruit from Brazilian Northeast is used to produce juice due to its flavor and vitamin C richness. However, its acceptance is limited due to its astringency. Cajuína is a derivate product appreciated by its characteristic flavor, freshness and lack of astringency, due to tannin removal. Cajuína is a light yellow beverage made from clarified cashew juice and sterilized after bottling. It differs from the integral and concentrated juice by the clarification and thermal treatment steps. Many problems such as haze and excessive browning could appear if these steps are not controlled. The objective of this work was divided into two stages with the aim to supply process information in order to obtain a good quality product with uniform characteristics (sensory and nutritional). Polyphenol-protein interaction was studied at the clarification step, which is an empirical process, to provide values on the amount of clarifying solution (gelatin) that must be added to achieve a complete juice clarification. Clarification essays were performed with juice dilutions of 1:2 and 1:10 and the effect of metabissulfite and tannic acid addition was evaluated. It was not possible to establish a clarification point. Metabissulfite did not influenced the clarification process however tannic acid addition displaced the clarification point, showing the difficulty visual monitoring of the process. Thermal treatment of clarified juice was studied at 88, 100, 111 e 121 °C. To evaluate the non-enzymatic browning, vitamin C, 5-hidroximetilfurfural (5-HMF) and sugar variation were correlated with color parameters (reflectance spectra, color difference and CIELAB). Kinetic models were obtained for reflectance spectra, ascorbic acid and 5-HMF. It was observed that 5-HMF introduction followed a first order kinetic rate at the beginning of the thermal treatment and a zero order kinetic at later process stages. An inverse correlation was observed between absorbance at 420 nm and ascorbic acid degradation, which indicates that ascorbic acid might be the principal factor on cajuína non-enzymatic browning. Constant sugar concentration showed that this parameter did not contribute directly to the nonenzymatic browning. Optimization techniques showed showed that to obtain a high vitamin C and a low 5-HMF content, the process must be done at 120 ºC. With the water-bath thermal treatment, the 90 °C temperature promoted a lower ascorbic acid degradation at the expense of a higher 5-HMF level

Variáveis qualitativas da pulverização em feijão, Bidens pilosa E Brachiaria plantaginea

Conduziu-se este trabalho, com o objetivo de avaliar a qualidade da deposição da calda de pulverização em plantas de feijão (Phaseolus vulgaris L.), Bidens pilosa L. e de Brachiaria plantaginea (Link) Hitchc. presentes na linha e entrelinha da cultura. Foi utilizado como traçador o corante Azul Brilhante FDC-1 (500 ppm). Utilizaram-se cinco pontas de pulverização: jato plano (XR 110015 VS e XR 11002 VS), jato plano duplo (TJ60 11002 VS) e jato cônico (TX-6 VS e TX-8 VS) e dois volumes de aplicação 150 e 200 L ha-1. O delineamento utilizado foi de blocos ao acaso, com 4 repetições. Foram amostradas 25 plantas em cada parcela/repetição, de plantas de feijão e plantas daninhas presentes na linha e na entrelinha da cultura. Após a aplicação, as plantas foram coletadas e lavadas em água destilada para quantificação do traçador em espectrofotômetro. Os dados ajustaram-se à curva de regressão pelo modelo de Gompertz. Os resultados evidenciaram que: para as plantas de feijão as pontas XR 110015 e TJ60 proporcionaram as deposições mais uniformes, nos volumes de 150 e 200 L ha-1, respectivamente; a ponta TX-6 no volume de 150 L ha-1 apresentou melhor uniformidade de distribuição para ambas as espécies de plantas daninhas presentes na linha da cultura; para as plantas daninhas presentes na entrelinha, no volume de 150 L ha-1, destacaram-se as pontas XR 110015 e TJ60 11002 para B. pilosa e B. plantaginea, respectivamente, no volume de 200 L ha-1 destacou-se a ponta TX-8 para ambas as espécies.

Características da pulverização em citros em função do volume de calda aplicado com turbopulverizador

Este trabalho teve como objetivo avaliar o efeito do volume de calda aplicado por um turbopulverizador sobre a deposição e a cobertura em folhas, ramos e frutos de citros. A pulverização foi realizada com um pulverizador tratorizado Arbus 2000/Valência em pomar de laranja 'Natal', com porte médio de 4,0 m, sendo avaliados seis volumes de calda (50; 70; 85; 100; 150 e 200% do volume-padrão utilizado pelo produtor, de 28 L planta-1). Após a pulverização de plantas uniformes com calda contendo cobre e o traçador fluorescente Poliglow 830 YLSS, amostras foram coletadas em nove setores da planta, sendo a avaliação da deposição feita usando-se análise do íon cobre por espectrofotômetro de absorção atômica, e a da cobertura, por meio de imagens digitalizadas analisadas pelo programa para computador IDRISI. A análise estatística mostrou que, na avaliação da cobertura e deposição em citros, a utilização de frutos como estrutura de amostragem tendeu a evidenciar melhor o efeito dos tratamentos. Tanto a deposição quanto a cobertura tenderam a ser maiores nos setores frontal e saia da planta. Tanto a deposição quanto a cobertura não foram prejudicadas pela utilização do volume de 70% (19,6 L planta-1), indicando que tal volume pode substituir o volume de 100% (28 L planta-1) sem prejuízos ao controle de pragas.

Síntese e caracterização de tungstatos de cério e estrôncio para fins catalíticos

The main goal of this work was to produce nanosized ceramic materials of the family of the tungstates (tungstates of cerium and strontium), and test them for their catalytic activity in processes involving the transformation of methane (CH4). The methodology used for the synthesis of the ceramic powders involved the complexation combining EDTA-citrate. The materials characterization was performed using simple and differential thermogravimetry, x-ray diffraction, transmission electron microscopy, and energy dispersive spectroscopy (EDS). The microstructure analysis was performed using the refinement by the Rietveld method, and the crystallite size and distribution of the materials was elucidate by the Scherrer and Williamson-Hall methods. The conditions of the synthesis process for the three envisaged materials (SrWO4, SrWO4 using tungsten oxide concentrate as raw material, and Ce2(WO4)3) were adjusted to obtain a single phase crystalline material. The catalytic tests were carried out in the presence of methane and synthetic air, which is composed of 21% O2 and 79% N2. The analysis of the conversion of the reaction was done with the aid of an fourier transform infrared device (FTIR). The analysis showed that, structurally, the SrWO4 produced using raw materials of high and poor purity (99% and 92%, respectively) are similar. The ideal parameters of calcination, in the tested range, are temperature of 1000 °C and time of calcination 5 hours. For the Ce2(WO4)3, the ideal calcination time and are temperature 15 hours and 1000°C, respectively. The Williamson-Hall method provided two different distributions for the crystallite size of each material, whose values ranged between the nanometer and micrometer scales. According to method of Scherrer, all materials produced were composed of nanometric crystallites. The analyses of transmission electron microscopy confirmed the results obtained from the Williamson- Hall method for the crystallite size. The EDS showed an atomic composition for the metals in the SrWO4 that was different of the theoretical composition. With respect to the catalytic tests, all materials were found to be catalytically active, but the reaction process should be further studied and optimized.

Macroalgas de ambientes lóticos da região centro-oeste do Paraná, região sul do Brasil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Disponibilidade hídrica potencial em face da distribuição espaço-temporal das precipitações no Estado do Rio Grande do Norte

The state of Rio Grande do Norte, possessor of an extremely irregular regime of rains, has the necessity of enlarge and specify the researches about its own hydro-climatic conditions, to achieve trustworthy results that are able to minimize the adversities imposed by these conditions and make possible the implementation of a better planning in the economic activities and of subsistence that somehow utilize of the multiple uses of hydro resources of the State. This way, the daily values observed from the pluviometric series of 166 posts, with 45 years uninterrupted of historic data, were adjusted to the incomplete gamma function to the determination of the probability of rain in the 36 period of ten days in which the year was divided. To the attainment of the α and β parameters of this function it was applied the method of the maximum verisimilitude allowing, in the end, to analyze the temporal and spatial distribution of the rain in the level of 75% of probability. The values of potential evapo-transpiration were calculated by the Linacre method that, through the SURFER software, were confronted with the dependant rain, obtaining, in this way, the spatialization of the potential hydro availability, which the values can be known to any period of ten days of the year, city and/or region of the state of Rio Grande do Norte. With the identification of the main meteorological systems that act in the State, we sought to better comprehend how this systems interfere, in the irregular regime of rain, in the situations of several clime in the major part of Rio Grande do Norte and in the hydro regional balance. And, finally, with these data in hand and with the generated maps, we verified that space-temporal distribution of the rain and of the potential hydro availability were heterogeneous in the whole State, mainly in the West and Central regions, inserted in potiguar s semi-arid, which, after the period of the rains station, suffers with dry season and length drought during the rest of the year

O Modelo de Ising inomogêneo: uma interrupção contínua entre as redes quadrada e triangular.

The ferromagnetic and antiferromagnetic Ising model on a two dimensional inhomogeneous lattice characterized by two exchange constants (J1 and J2) is investigated. The lattice allows, in a continuous manner, the interpolation between the uniforme square (J2 = 0) and triangular (J2 = J1) lattices. By performing Monte Carlo simulation using the sequential Metropolis algorithm, we calculate the magnetization and the magnetic susceptibility on lattices of differents sizes. Applying the finite size scaling method through a data colappse, we obtained the critical temperatures as well as the critical exponents of the model for several values of the parameter α = J2 J1 in the [0, 1] range. The ferromagnetic case shows a linear increasing behavior of the critical temperature Tc for increasing values of α. Inwhich concerns the antiferromagnetic system, we observe a linear (decreasing) behavior of Tc, only for small values of α; in the range [0.6, 1], where frustrations effects are more pronunciated, the critical temperature Tc decays more quickly, possibly in a non-linear way, to the limiting value Tc = 0, cor-responding to the homogeneous fully frustrated antiferromagnetic triangular case.

Fractais e Percolação na Recuperação de Petróleo

The complex behavior of a wide variety of phenomena that are of interest to physicists, chemists, and engineers has been quantitatively characterized by using the ideas of fractal and multifractal distributions, which correspond in a unique way to the geometrical shape and dynamical properties of the systems under study. In this thesis we present the Space of Fractals and the methods of Hausdorff-Besicovitch, box-counting and Scaling to calculate the fractal dimension of a set. In this Thesis we investigate also percolation phenomena in multifractal objects that are built in a simple way. The central object of our analysis is a multifractal object that we call Qmf . In these objects the multifractality comes directly from the geometric tiling. We identify some differences between percolation in the proposed multifractals and in a regular lattice. There are basically two sources of these differences. The first is related to the coordination number, c, which changes along the multifractal. The second comes from the way the weight of each cell in the multifractal affects the percolation cluster. We use many samples of finite size lattices and draw the histogram of percolating lattices against site occupation probability p. Depending on a parameter, ρ, characterizing the multifractal and the lattice size, L, the histogram can have two peaks. We observe that the probability of occupation at the percolation threshold, pc, for the multifractal is lower than that for the square lattice. We compute the fractal dimension of the percolating cluster and the critical exponent β. Despite the topological differences, we find that the percolation in a multifractal support is in the same universality class as standard percolation. The area and the number of neighbors of the blocks of Qmf show a non-trivial behavior. A general view of the object Qmf shows an anisotropy. The value of pc is a function of ρ which is related to its anisotropy. We investigate the relation between pc and the average number of neighbors of the blocks as well as the anisotropy of Qmf. In this Thesis we study likewise the distribution of shortest paths in percolation systems at the percolation threshold in two dimensions (2D). We study paths from one given point to multiple other points

Fractais e percolação na recuperação de Petróleo

The complex behavior of a wide variety of phenomena that are of interest to physicists, chemists, and engineers has been quantitatively characterized by using the ideas of fractal and multifractal distributions, which correspond in a unique way to the geometrical shape and dynamical properties of the systems under study. In this thesis we present the Space of Fractals and the methods of Hausdorff-Besicovitch, box-counting and Scaling to calculate the fractal dimension of a set. In this Thesis we investigate also percolation phenomena in multifractal objects that are built in a simple way. The central object of our analysis is a multifractal object that we call Qmf . In these objects the multifractality comes directly from the geometric tiling. We identify some differences between percolation in the proposed multifractals and in a regular lattice. There are basically two sources of these differences. The first is related to the coordination number, c, which changes along the multifractal. The second comes from the way the weight of each cell in the multifractal affects the percolation cluster. We use many samples of finite size lattices and draw the histogram of percolating lattices against site occupation probability p. Depending on a parameter, ρ, characterizing the multifractal and the lattice size, L, the histogram can have two peaks. We observe that the probability of occupation at the percolation threshold, pc, for the multifractal is lower than that for the square lattice. We compute the fractal dimension of the percolating cluster and the critical exponent β. Despite the topological differences, we find that the percolation in a multifractal support is in the same universality class as standard percolation. The area and the number of neighbors of the blocks of Qmf show a non-trivial behavior. A general view of the object Qmf shows an anisotropy. The value of pc is a function of ρ which is related to its anisotropy. We investigate the relation between pc and the average number of neighbors of the blocks as well as the anisotropy of Qmf. In this Thesis we study likewise the distribution of shortest paths in percolation systems at the percolation threshold in two dimensions (2D). We study paths from one given point to multiple other points. In oil recovery terminology, the given single point can be mapped to an injection well (injector) and the multiple other points to production wells (producers). In the previously standard case of one injection well and one production well separated by Euclidean distance r, the distribution of shortest paths l, P(l|r), shows a power-law behavior with exponent gl = 2.14 in 2D. Here we analyze the situation of one injector and an array A of producers. Symmetric arrays of producers lead to one peak in the distribution P(l|A), the probability that the shortest path between the injector and any of the producers is l, while the asymmetric configurations lead to several peaks in the distribution. We analyze configurations in which the injector is outside and inside the set of producers. The peak in P(l|A) for the symmetric arrays decays faster than for the standard case. For very long paths all the studied arrays exhibit a power-law behavior with exponent g ∼= gl.

Formação de caudas maxwellianas no Contexto da rotação estelar

In this Thesis, we analyzed the formation of maxwellian tails of the distributions of the rotational velocity in the context of the out of equilibrium Boltzmann Gibbs statistical mechanics. We start from a unified model for the angular momentum loss rate which made possible the construction of a general theory for the rotational decay in the which, finally, through the compilation between standard Maxwellian and the relation of rotational decay, we defined the (_, _) Maxwellian distributions. The results reveal that the out of equilibrium Boltzmann Gibbs statistics supplies us results as good as the one of the Tsallis and Kaniadakis generalized statistics, besides allowing fittings controlled by physical properties extracted of the own theory of stellar rotation. In addition, our results point out that these generalized statistics converge to the one of Boltzmann Gibbs when we inserted, in your respective functions of distributions, a rotational velocity defined as a distribution

Parâmetros físico-químicos de estrelas nos campos de exoplanetas do satélite corot

A rotação estelar é um dos mais importantes observáveis da evolução estelar. Neste sentido, o satélite CoRoT representa uma oportunidade única de medir os períodos rotacionais para uma amostra de estrelas estatisticamente robusta, oferecendo dados absolutamente necessários para o estudo da rotação e seu papel na evolução estelar. Para conseguir isto, um passo fundamental é a caracterização física e química das estrelas observadas pelo CoRoT, especificamente devido ao fato de que o cálculo de períodos rotacionais confiáveis é um trabalho difícil sem a ajuda dos parâmetros estelares. Desta forma, foi elaborado um importante seguimento observacional das estrelas nos campos do CoRoT do anticentro LRa01 e do centro LRc01, permitindo a correta identificação dos períodos que reflitam a modulação rotacional. Nesta tese de doutorado são apresentados os resultados de tal seguimento. Parâmetros físicos e químicos, tais como temperatura efetiva Teff , gravidade superficial log(g), velocidade de microturbulência Vmic, abundância de ferro [Fe/H], velocidade de rotação projetada Vsin(i), e abundância de lítio A(Li) são apresentados para uma amostra de 116 estrelas dos campos CoRoT. Elas se encontram em diferentes estágios evolutivos, desde a sequência principal (SP) até o ramo das gigantes vermelhas (GV). As observações foram feitas utilizando os espectrógrafos UVES (VLT) e HYDRA (CTIO). Para a derivação de tais parâmetros foram utilizados o programa TurboSpectrum e os modelos de atmosfera de MARCS. Paralelamente, velocidades rotacionais Vsin(i) foram obtidas a partir do ajuste dos perfis observados e sintéticos das linhas de ferro e por meio de uma calibração de função de correlação cruzada (CCF). Períodos rotacionais Prot para 77 estrelas da amostra foram obtidos a partir das curvas de luz do satélite CoRoT. Extensas tabelas destes parâmetros e seus respectivos erros são apresentadas. Foram encontradas diferenças nas distribuições de Teff , [Fe/H] e estágios evolutivos entre os diferentes campos do CoRoT, indicando possíveis efeitos de seleção na amostra, assim como a existência de diferentes populações estelares do disco Galáctico. Por outro lado, o comportamento rotacional e as abundâncias de lítio não apresentam diferenças entre estrelas de parâmetros físicos similares, mas que pertencem a diferentes campos do CoRoT. A partir da análise de temperaturas, foi encontrada uma maior extinção por avermelhamento para estrelas do CoRoT localizadas no campo LRc01, assim como um gradiente deste valor em função da distância. Os resultados mostram que as abundâncias de lítio, as velocidades de rotação e os períodos rotacionais apresentam o mesmo comportamento descrito na literatura. Por outro lado, é apresentada pela primeira vez a relação que existe entre o lítio e o período de rotação em diferentes estágios evolutivos, mostrando, tal como era esperado, que ambas as grandezas possuem uma anticorrelação. Também é apresentada a evolução simultânea da rotação e do lítio, e foram calculadas relações que permitem obter valores médios de A(Li) como função da temperatura efetiva e do período rotacional. Os dados apresentados nesta tese de doutorado representam um importante ponto de partida para serem utilizados como uma amostra de calibração para diferentes programas no contexto da missão do satélite CoRoT, uma vez que a lista de estrelas aqui analisadas são parte das mais brilhantes que compõem o campo Exo do CoRoT

Um estudo da rotação em estrelas da seqüência principal

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Desenvolvimento e caracterização de dispositivos para reposição de filmes finos por descarga em cátodo oco

In the present work we use a plasma jet system with a hollow cathode to deposit thin TiO2 films on silicon substrates as alternative at sol-gel, PECVD, dip-coating e magnetron sputtering techniques. The cylindrical cathode, made from pure titanium, can be negatively polarized between 0 e 1200 V and supports an electrical current of up to 1 A. An Ar/O2 mixture, with a total flux of 20 sccm and an O2 percentage ranging between 0 and 30%, is passed through a cylindrical hole machined in the cathode. The plasma parameters and your influence on the properties of deposited TiO2 films and their deposition rate was studied. When discharge occurs, titanium atoms are sputtered/evaporated. They are transported by the jet and deposited on the Si substrates located on the substrate holder facing the plasma jet system at a distance ranging between10 and 50 mm from the cathode. The working pressure was 10-3 mbar and the deposition time was 10 -60 min. Deposited films were characterized by scanning electron microscopy and atomic force microscopy to check the film uniformity and morphology and by X-ray diffraction to analyze qualitatively the phases present. Also it is presented the new dispositive denominate ionizing cage, derived from the active screen plasma nitriding (ASPN), but based in hollow cathode effect, recently developed. In this process, the sample was involved in a cage, in which the cathodic potential was applied. The samples were placed on an insulator substrate holder, remaining in a floating potential, and then it was treated in reactive plasma in hollow cathode regime. Moreover, the edge effect was completely eliminated, since the plasma was formed on the cage and not directly onto the samples and uniformity layer was getting in all sampl