On-line concentration of neutral and charged species in capillary electrochromatography with a methacrylate-based monolithic stationary phase

A method involving self-concentration, on-column enrichment and field-amplified sample stacking for on-line concentration in capillary electrochromatography with a polymer monolithic column is presented. Since monolithic columns eliminate the frit fabrication and the problems associated with frits, the experimental conditions could be more flexibly adjusted to obtain higher concentration factor in comparison with conventional particulate packed columns. With self-concentration effect, the detection sensitivity of benzene and hexylbenzene is improved by a factor of 4 and 8, respectively. With on-column enrichment and ultralong injection, improvement as high as 22 000 times in detection sensitivity of benzoin is achieved. Furthermore, a combination of the three above-mentioned methods yields up to a 24000-fold improvement in detection sensitivity for caffeine, a charged compound. Parameters affecting the efficiency of on-line concentration are investigated systematically. In addition, equations describing on-line concentration process are deduced.

Effect of sodium alginate concentration on membrane strength and permeating property of poly-l-arginine group microcapsule

A novel poly-l-arginine microcapsule was prepared due to its nutritional function and pharmacological efficacy. A high-voltage electrostatic droplet generator was used to make uniform microcapsules. The results show that the membrane strength and permeating property are both remarkably affected with the changes of sodium alginate concentration. With the sodium alginate concentration increasing, gel beads sizes increase from 233 mum to 350 mum, release ratio is also higher at the same time, but the membrane strength decreases.

Thermokinetic investigation of effect of temperature on optimum NaCl concentration for petroleum bacterial growth

The power-time curves of growth of three strains of petroleum bacteria at different NaCl concentrations at 40.0 and 50.0 degreesC have been determined by using a 2277 Thermometric Thermal Activity Analyser. An equation of a power-time curve, ln[alphaP(K)/P(t) - 1] = ln[(alphaK - N-0)/N-0] - alphakt, was established based on the generalized logistic equation, where P(t) is the thermal power at time t, K the carrying capacity, P-K = P0K, P-0 the thermal power of one cell, N-0 the bacterial population at time zero, alpha = (k - D)/k. The method of four observed points with the same time interval was used to calculate the value of P-K. The growth rate constant k and the death rate constant D were calculated. The NaCl concentration of optimum growth rate of petroleum bacteria at 40.0 and 50.0 degreesC, respectively, have been obtained according to the curves k - D versus NaCl concentration, which are 0.26, 0.54 and 0.57 mol l(-1) for B-1, B-2 and B-3, respectively, at 50.0 degreesC, 0.26, 0.55 and 0.56 mol l(-1) for B-1, B-2 and B-3, respectively, at 40.0 degreesC. The results indicated that the effect of temperature on NaCl concentration of optimum growth rate was small. (C) 2002 Elsevier Science B.V. All rights reserved.

Rhythmic Growth-Induced Ring-Banded Spherulites with Radial Periodic Variation of Thicknesses Grown from Poly(epsilon-caprolactone) Solution with Constant Concentration

Birefringent ring-banded spherulites with radial periodic variation of thicknesses were grown from poly(epsilon-caprolactone) (PCL) solutions under conditions for which the Solution concentration was held constant during the whole development of the morphology. The as-grown ring-banded spherulites were investigated by optical (OM) and atomic force (AFM) microscopies, by transmission electron microscopy (TEM) of samples sectioned parallel to the plane of film, and also by electron diffraction (ED) and grazing incidence X-ray diffraction (GIXD) techniques.

Effect of Zn concentration on the microstructures and mechanical properties of extruded Mg-7Y-4Gd-0.4Zr alloys

Microstructures and mechanical properties of the Mg-7Y-4Gd-xZn-0.4Zr (x = 0.5, 1.5, 3, and 5 wt.%) alloys in the as-cast, as-extruded, and peak-aged conditions have been investigated by using optical microscopy, scanning electron microscope, X-ray diffraction, and transmission electron microscopy. It is found that the peak-aged Mg-7Y-4Gd-1.5Zn-0.4Zr alloys have the highest strength after aging at 220 A degrees C. The highest ultimate tensile strength and yield tensile strength are 418 and 320 MPa, respectively. The addition of 1.5 wt.% Zn to the based alloys results in a greater aging effect and better mechanical properties at both room and elevated temperatures. The improved mechanical properties are mainly ascribed to both a fine beta' phase and a long periodic stacking-ordered structure, which coexist together in the peak-aged alloys.

Effect of dye concentration on the charge carrier transport in molecularly doped organic light-emitting diodes

The effect of the concentration of 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7, 7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as dopant in tris(8-quinolinolato) aluminum (Alq(3)) on the charge carrier transport in Alq(3):DCJTB was investigated by measuring the steady current-voltage characteristics and the transient electroluminescence. The dopant concentration dependence of the current-voltage relationship clearly indicates the carrier trapping by the DCJTB molecule. The DCJTB concentration significantly affects the electron mobility in Alq(3):DCJTB. The mobility has a nontrivial dependence on the doping level. For relatively low doping levels, less than 1%, the electron mobility of Alq(3):DCJTB decreases with the doping level. An increasing mobility is then observed if the dopant concentration is further increased, followed by a decrease for doping levels larger than similar to2%. The change of the electron mobility with the DCJTB concentration in Alq(3) is attributed to the additional energetic disorder due to potential fluctuations caused by the dipole-dipole interaction of random distribution dopant at the relatively low doping concentration, and to the phase separation at the high doping concentration.

Modeling of organic light-emitting diodes with graded concentration in the emissive multilayer

We model the electrical behavior of organic light-emitting diodes whose emissive multilayer is formed by blends of an electron transporting material, tris-(8-hydroxyquinoline) aluminum (Alq(3)) and a hole transporting material, N,N-'-diphenyl-N,N-'-bis(1,1(')-biphenyl)-4,4-diamine. The multilayer is composed of layers of different concentration. The Alq(3) concentration gradually decreases from the cathode to the anode. We demonstrate that these graded devices have higher efficiency and operate at lower applied voltages than devices whose emissive layer is made of nominally homogeneous blends. Our results show an important advantage of graded devices, namely, the low values of the recombination rate distribution near the cathode and the anode, so that electrode quenching is expected to be significantly suppressed in these devices.