A rapid and reliable bonding process for microchip electrophoresis fabricated in glass substrates

In this report, we describe a rapid and reliable process to bond channels fabricated in glass substrates. Glass channels were fabricated by photolithography and wet chemical etching. The resulting channels were bonded against another glass plate containing a 50-mu m thick PDMS layer. This same PDMS layer was also used to provide the electrical insulation of planar electrodes to carry out capacitively coupled contactless conductivity detection. The analytical performance of the proposed device was shown by using both LIF and capacitively coupled contactless conductivity detection systems. Efficiency around 47 000 plates/m was achieved with good chip-to-chip repeatability and satisfactory long-term stability of EOF. The RSD for the EOF measured in three different devices was ca. 7%. For a chip-to-chip comparison, the RSD values for migration time, electrophoretic current and peak area were below 10%. With the proposed approach, a single chip can be fabricated in less than 30 min including patterning, etching and sealing steps. This fabrication process is faster and easier than the thermal bonding process. Besides, the proposed method does not require high temperatures and provides excellent day-to-day and device-to-device repeatability.

Understanding Wax Printing: A Simple Micropatterning Process for Paper-Based Microfluidics

This technical note describes a detailed study on wax printing, a simple and inexpensive method for fabricating microfluidic devices in paper using a commercially available printer and hot plate. The printer prints patterns of solid wax on the surface of the paper, and the hot plate melts the wax so that it penetrates the full thickness of the paper. This process creates complete hydrophobic barriers in paper that define hydrophilic channels, fluid reservoirs, and reaction zones. The design of each device was based on a simple equation that accounts for the spreading of molten wax in paper.

Formation Mechanism via a Heterocoagulation Approach of FePt Nanoparticles Using the Modified Polyol Process

Herein, we report a new approach of an FePt nanoparticle formation mechanism studying the evolution of particle size and composition during the synthesis using the modified polyol process. One of the factors limiting their application in ultra-high-density magnetic storage media is the particle-to-particle composition, which affects the A1-to-L1(0) transformation as well as their magnetic properties. There are many controversies in the literature concerning the mechanism of the FePt formation, which seems to be the key to understanding the compositional chemical distribution. Our results convincingly show that, initially, Pt nuclei are formed due to reduction of Pt(acac)(2) by the diol, followed by heterocoagulation of Fe cluster species formed from Fe(acac)(3) thermal decomposition onto the Pt nuclei. Complete reduction of heterocoagulated iron species seems to involve a CO-spillover process, in which the Pt nuclei surface acts as a heterogeneous catalyst, leading to the improvement of the single-particle composition control and allowing a much narrower compositional distribution. Our results show significant decreases in the particle-to-particle composition range, improving the A1-to-L1(0) phase transformation and, consequently, the magnetic properties when compared with other reported methods.

Application of chemometric methods in the evaluation of chemical and spectroscopic data on organic matter from Oxisols in sewage sludge applications

Chemometric methods can contribute to soil research by permitting the extraction of more information from the data. The aim of this work was to use Principal Component Analysis to evaluate data obtained through chemical and spectroscopic methods on the changes in the humification process of soil organic matter from two tropical soils after sewage sludge application. In this case, humic acids extracted from Typic Eutrorthox and Typic Haplorthox soils with and without sewage sludge application for 7 consecutive years were studied. The results obtained for all of the samples and methods showed two clusters: samples extracted from the two soil types. These expected results indicated the textural difference between the two soils was more significant than the differences between treatments (control and sewage sludge application) or between depths. In this case, an individual chemometric treatment was made for each type of soil. It was noted that the characterization of the humic acids extracted from soils with and without sewage sludge application after 7 consecutive years using several methods supplies important results about changes in the humification degree of soil organic matter, These important result obtained by Principal Component Analysis justify further research using these methods to characterize the changes in the humic acids extracted from sewage sludge-amended soils. (C) 2009 Elsevier B.V. All rights reserved.

Impact of forced-aging process on Madeira Wine flavor

The aim of this study was to determine the optimal temperature and baking time to obtain a Madeira wine considered typical by an expert panel. For this purpose simultaneous descriptive analyses of typical Madeira wines were performed, and seven descriptors were selected: “dried fruit”, “nutty”, “musty”, “baked”, “oak”, “mushroom”, and “brown sugar”. Up to 10 odor-active zones were the most frequently cited by the members of the GC-olfactometry panel as corresponding to the panel’s descriptors. The odor importance of each of the zones reported by the GC-O analysis was ranked by AEDA. Three odor zones were identified as common to both Malvasia and Sercial wines and had retention indices (RI) of 1993 (“brown sugar” and “toasted”), 2151 (“brown sugar”), and 2174 (“nutty”, “driedfruits”);sotolonwasidentifiedasresponsibleforthislastaroma.Severalmoleculeswereselected to be quantified on baked wines on the basis of AEDA results and expected Maillard volatiles, such as sotolon, furfural, 5-methylfurfural, 5-ethoximethylfurfural, methional, and phenylacetaldehyde. It was observed that typicity scores were positively correlated with the concentrations of sotolon and sugar and baking time and negatively with the fermentation length.

Pseudomonas aeruginosa LBI production as an integrated process using the wastes from sunflower-oil refining as a substrate

Pseudomonas aeruginosa LBI produced surface active rhamnolipids when cultivated on waste from the sunflower-oil process under different conditions. These biosurfactants, which reduce the superficial and interfacial tensions between fluids, offer advantages over their chemical counterparts, especially because of their ecological acceptability. These molecules can be used in fields as diverse as chemical, pharmaceutical and petrochemical industries. In this work, we present the effect of C/N ratio on growth and production yield. The best production yields (Y-P/S) were achieved for C/N ratios (in g/g) of 8/1 (0.22) and 6.4/1 (0.23). The product concentration was very satisfactory (7.3 g/L) at C/N ratio of 8/1, especially when considering that the substrate was basically composed of wastes that would otherwise constitute an environmental disposal problem. (c) 2007 Elsevier Ltd. All rights reserved.

Degenerative process and cell death in salivary glands of Rhipicephalus sanguineus (Latreille, 1806) (Acari: Ixodidae) semi-engorged female exposed to the acaricide permethrin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chemical attributes of a degraded soil after application of water treatment sludges

Mining is an activity that tends to degrade the environment. The restoration of mining areas, aims to accelerate and improve the succession process according to its future use. The objective of this work was to rehabilitate a soil degraded by tin mining activities in the Amazon Basin (Jamari National Forest, State of Rondonia) with the application of water treatment sludge (WTS), and verify the effect of Sludge on Values of pH (CaCl2 0.01 mol L-1), organic matter, P, Ca, Mg, K, H+Al, and soil micronutrient contents when Cultivated with native plants, legumes, and grass species. A factorial (3 x 5) experimental design was used to optimize the rehabilitation of these areas including three N rates (100, 200, and 300 mg N ka(-1) soil supplied by WTS), five plant species (grasses, legumes, and native plants), and two controls (degraded soil with no fertilizer and degraded soil fertilized with mineral fertilizers), with four replications. WTS increased pH values. The chemical products used to treat the water contributed, in greater extension, to increase soil Ca and Fe contents. The use of WTS as fertilizer proved viable, since it contains nutrients for plants; however, nitrogen Should not be used as a criterion to define the rate of Sludge application, because it is present at small amounts in the WTS.

Application of chemometric methods in the evaluation of chemical and spectroscopic data on organic matter from Oxisols in sewage sludge applications

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chemical and physical attributes of two substratum for eucalypt seedling production

This work evaluated the viability of one commercial substrate with pinus bark, vermiculite and 30% of coconut fiber for Eucalyptus grandis seedlings production under different water management: 6, 8, 10, 12 e 14 mm day(-1). In relation to the substrates, it was evaluated, before and after the seedlings production, the total content of carbon, nitrogen and organic substances, pH and EC of the extract, the content of macronutrients (P, K, Ca, S, Mg) and macronutrients (B, Fe, Mn, Cu, Zn), as well as total porosity, density and water retention. It was evaluated the macro and mcronutrients accumulation in the roots and in the aerial part of the seedlings, 105 days after sowing. It was concluded that the substrates presented some distinct properties of those cited as ideal for production in containers with irrigation and fertilization. At the end of the production process, both substrates registered nutrient content little influenced by water management what would guarantee the initial development of the plants in the field.

Modelling the effect of the physical and chemical characteristics of the materials used as casing layers on the production parameters of Agaricus bisporus

The aim of this research was to show the mathematical data obtained through the correlations found between the physical and chemical characteristics of casing layers and the final mushrooms' properties. For this purpose, 8 casing layers were used: soil, soil + peat moss, soil + black peat, soil + composted pine bark, soil + coconut fibre pith, soil + wood fibre, soil + composted vine shoots and, finally, the casing of La Rioja subjected to the ruffling practice. The conclusion that interplays in the fructification process with only the physical and chemical characteristics of casing are complicated was drawn. The mathematical data obtained in earliness could be explained in non-ruffled cultivation. The variability observed for the mushroom weight and the mushroom diameter variables could be explained in both ruffled and non-ruffled cultivations. Finally, the properties of the final quality of mushrooms were established by regression analysis.

Study of the carbon dioxide chemical fixation-activation by guanidines

Fixation of CO2 is one of the most important priorities of the scientific community dedicated to reduce global warming. In this work, we propose new methods for the fixation of CO2 using the guanidine bases tetramethylguanidine (TMG) and 1,3,4,6,7,8-hexahydro-2H-pyrimido[1,2-a]-pyrimidine (TBD). In order to understand the reactions occurring during the CO2 fixation and release processes, we employed several experimental methods, including solution and solid-state NMR, FTIR, and coupled TGA-FTIR. Quantum mechanical NMR calculations were also carried out. Based on the results obtained, we concluded that CO2 fixation with both TMG and TBD guanidines is a kinetically reversible process, and the corresponding fixation products have proved to be useful as transcarboxylating compounds. Afterward, CO2 thermal releasing from this fixation product with TBD was found to be an interesting process for CO2 capture and isolation purposes. (C) 2008 Elsevier Ltd. All rights reserved.

Detection of glucose and triglycerides using information visualization methods to process impedance spectroscopy data

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

DFT study of the water-assisted tautomerization process between hydrated oxide, MO(H2O)(+), and dihydroxide, M(OH)(2)(+) cations (M = V, Nb and Ta)

Density functional theory (DFT) calculations point out that the participation of water can effectively lower the barrier height for the isomerization process between hydrated oxide cation, MO(H2O)(+), and dihydroxide cation, M(OH)(2)(+), (M = V, Nb and Ta). The catalytic effect is achieved by a water-assisted mechanism in which water acts as proton donor and acceptor, via a transition structure corresponding to a six-membered ring. In the case of vanadium atom, the presence of two water molecules has been taken into account and the tautomerization becomes nearly barrierless, decreasing both the stability of the transition structures relative to intermediates and the depths of wells associated with the intermediates. (C) 2003 Elsevier B.V. All rights reserved.

Pressure-induced electrical and structural anomalies in Pb1-xCaxTiO3 thin films grown at various oxygen pressures by chemical solution route

Lead calcium titanate (Pb1-xCaxTiO3 or PCT) thin films have been thermally treated under different oxygen pressures, 10, 40 and 80 bar, by using the so-called chemical solution deposition method. The structural, morphological, dielectric and ferroelectric properties were characterized by x-ray diffraction, FT-infrared and Raman spectroscopy, atomic force microscopy and polarization-electric-field hysteresis loop measurements. By annealing at a controlled pressure of around 10 and 40 bar, well-crystallized PCT thin films were successfully prepared. For the sample submitted to 80 bar, the x-ray diffraction, Fourier transformed-infrared and Raman data indicated deviation from the tetragonal symmetry. The most interesting feature in the Raman spectra is the occurrence of intense vibrational modes at frequencies of around 747 and 820 cm(-1), whose presence depends strongly on the amount of the pyrochlore phase. In addition, the Raman spectrum indicates the presence of symmetry-breaking disorder, which would be expected for an amorphous (disorder) and mixed pyrochlore-perovskite phase. During the high-pressure annealing process, the crystallinity and the grain size of the annealed film decreased. This process effectively suppressed both the dielectric and ferroelectric behaviour. Ferroelectric hysteresis loop measurements performed on these PCT films exhibited a clear decrease in the remanent polarization with increasing oxygen pressure.