ACIDITY OF MODIFIED MORDENITES SYNTHESIZED FROM RICE HUSK SILICA AND CATALYTIC TRANSFORMATION OF METHYLBUTYNOL

Mordenite (MOR) was synthesized using rice husk silica and modified by base (B), acid (A) or acid-base (AB) and converted to H-form. The modification did not destroy the MOR structure but increased surface area and generated mesopores. Lewis acidity of the parent and modified MOR samples investigated by aluminum NMR and NH3-TPD showed a decrease in the following order: HMOR > BMOR > ABMOR > AMOR. For the catalytic transformation of methylbutynol, ABMOR provided the highest conversion and selectivity of products from acid sites.

TUNGSTOPHOSPHORIC ACID HETEROGENIZED ONTO NH4ZSM5 AS AN EFFICIENT AND RECYCLABLE CATALYST FOR THE PHOTOCATALYTIC DEGRADATION OF DYES

Materials based on tungstophosphoric acid (TPA) immobilized on NH4ZSM5 zeolite were prepared by wet impregnation of the zeolite matrix with TPA aqueous solutions. Their concentration was varied in order to obtain TPA contents of 5%, 10%, 20%, and 30% w/w in the solid. The materials were characterized by N2 adsorption-desorption isotherms, XRD, FT-IR, 31P MAS-NMR, TGA-DSC, DRS-UV-Vis, and the acidic behavior was studied by potentiometric titration with n-butylamine. The BET surface area (SBET) decreased when the TPA content was raised as a result of zeolite pore blocking. The X-ray diffraction patterns of the solids modified with TPA only presented the characteristic peaks of NH4ZSM5 zeolites, and an additional set of peaks assigned to the presence of (NH4)3PW12O40. According to the Fourier transform infrared and 31P magic angle spinning-nuclear magnetic resonance spectra, the main species present in the samples was the [PW12O40]3- anion, which was partially transformed into the [P2W21O71]6- anion during the synthesis and drying steps. The thermal stability of the NH4ZSM5TPA materials was similar to that of their parent zeolites. Moreover, the samples with the highest TPA content exhibited band gap energy values similar to those reported for TiO2. The immobilization of TPA on NH4ZSM5 zeolite allowed the obtention of catalysts with high photocatalytic activity in the degradation of methyl orange dye (MO) in water, at 25 ºC. These can be reused at least three times without any significant decrease in degree of degradation.

HYDROLYTIC DEGRADATION BEHAVIOR OF PLLA NANOCOMPOSITES REINFORCED WITH MODIFIED CELLULOSE NANOCRYSTALS

Bionanocomposites derived from poly(L-Lactide) (PLLA) were reinforced with chemically modified cellulose nanocrystals (m-CNCs). The effects of these modified cellulose nanoparticles on the mechanical and hydrolytic degradation behavior of polylactide were studied. The m-CNCs were prepared by a method in which hydrolysis of cellulose chains is performed simultaneously with the esterification of hydroxyl groups to produce modified nanocrystals with ester groups. FTIR, elemental analysis, TEM, XRD and contact angle measurements were used to confirm and characterize the chemical modifications of the m-CNCs. These bionanocomposites gave considerably better mechanical properties than neat PLLA based on an approximately 100% increase in tensile strength. Due to the hydrophobic properties of the esterified nanocrystals incorporated into a polymer matrix, it was also demonstrated that a small amount of m-CNCs could lead to a remarkable decrease in the hydrolytic degradation rate of the biopolymer. In addition, the m-CNCs considerably delay the degradation of the nanocomposite by providing a physical barrier that prevents the permeation of water, which thus hinders the overall absorption of water into the matrix. The results obtained in this study show the nanocrystals can be used to reinforce polylactides and fine-tune their degradation rates in moist or physiological environments.

DIRECT INFUSION ESI-MS APPLIED IN THE DETECTION OF BYPRODUCTS DUE TO REDUCTIVE DEGRADATION OF ACETAMIPRID BY ZERO-VALENT IRON

This study investigated the reductive degradation of acetamiprid (5 mg L-1) in aqueous medium (at pH 2.0) induced by zero-valent iron (50 mg). The process was monitored using high-performance liquid chromatography (HPLC) to determine the degradation rate as a function of reaction time, and direct infusion electrospray ionization mass spectrometry (DI-ESI-MS) to search for (and potentially characterize) any possible byproducts formed during degradation. The results obtained via HPLC showed that after 60 min, the degradation of the substrate reached nearly 100% in an acidic medium, whereas the mineralization rate (as determined by total organic carbon measurements) was as low as 3%. Data obtained by DI-ESI-MS showed that byproducts were formed mainly by insertions of hydrogen atoms into the nitrile, imine, and pyridine ring moieties, in addition to the observation of chlorine substitution by hydrogen replacement (hydrodechlorination) reactions.

FAST GC-FID METHOD FOR MONITORING ACIDIC AND BASIC CATALYTIC TRANSESTERIFICATION REACTIONS IN VEGETABLE OILS TO METHYL ESTER BIODIESEL PREPARATION

A fast gas chromatography with a flame ionisation detector (GC-FID) method for the simultaneous analysis of methyl palmitate (C16:0), stearate (C18:0), oleate (C18:1), linoleate (C18:2) and linolenate (C18:3) in biodiesel samples was proposed. The analysis was conducted in a customised ionic-liquid stationary-phase capillary, SLB-IL 111, with a length of 14 m, an internal diameter of 0.10 mm, a film thickness of 0.08 µm and operated isothermally at 160 °C using hydrogen as the carrier gas at a rate of 50 cm s-1 in run time about 3 min. Once methyl myristate (C14:0) is present lower than 0.5% m/m in real samples it was used as an internal standard. The method was successful applied to monitoring basic and acidic catalysis transesterification reactions of vegetable oils such as soybean, canola, corn, sunflower and those used in frying process.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Thermal degradation behaviour of some polydithiooxamide metal complexes

The thermal decomposition behavior of the Fe(II), Co(II), Ni(II) and Zn(II) complexes of polydithiooxamide has been investigated by thermogravimetric analysis (TGA) at a heating rate of 20°C min-1 under nitrogen. The Coats-Redfern integral method is used to evaluate the kinetic parameters for the successive steps in the decomposition sequence observed in the TGA curves. The processes of thermal decomposition taking place in the four complexes are studied comparatively as the TGA curves indicate the difference in the thermal decomposition behavior of these complexes. The thermal stabilities of these complexes are discussed in terms of repulsion among electron pairs in the valence shell of the central ion and electronegativity effects.

Photoelectrocatalytical degradation of basic blue 41 dye using nanoporous semiconductor of Ti/TiO2

O presente trabalho investiga a degradação fotoeletrocatalítica do corante Azul Básico 41 (AB 41) amplamente utilizado na tintura de fibras sintéticas, utilizando um semicondutor Ti/TiO2 como fotoanodo. 100% de degradação foi obtida após 60 min de tratamento de 8,33x10-5 mol L-1 do corante em 0,1 mol L−1 Na2SO4, pH 2 sob densidade de corrente de 0,40 mA cm−2 e irradiação UV. Ainda foi obtido 80% de remoção de carbono orgânico total, cuja oxidação segue uma reação de pseudo-primeira ordem com constante de velocidade inicial de -0,040 mim-1 e uma eficiência de corrente de 51%. Os resultados são superiores á fotocatálise convencional nas mesmas condições sem a polarização do fotoanodo que leva a 65% de mineralização sob constante de velocidade de -0,024 mim-1.

A novel indicator reaction for the catalytic determination of V(V) at ppb levels by the kinetic spectrophotometric method

A novel sensitive and relatively selective kinetic method is presented for the determination of V(V), based on its catalytic effect on the oxidation reaction of Ponceau Xylydine by potassium bromate in presence of 5-sulfosalicylic acid (SSA) as activator. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of Ponceau Xylydine at 640 nm between 0.5 to 7 min (the fixed time method) in H3PO4 medium at 25ºC. The effect of various parameters such as concentrations of H3PO4, SSA, bromate and Ponceau Xylydine, temperature and ionic strength on the rate of net reaction were studied. The method is free from most interferences, especially from large amounts of V(IV). The decrease in absorbance is proportional to the concentration of V(V) over the entire concentration range tested (1-15 ng mL−1) with a detection limit of 0.46 ng mL-1 (according to statistical 3Sblank/k criterion) and a coefficient of variation (CV) of 1.8% (for ten replicate measurement at 95% confidence level). The proposed method suffers few interferences such as Cr(VI) and Hg(II) ions. The method was successfully applied to the determination of V(V) in tap water, drinking water, bottled mineral water samples and a certified standard reference material such as SRM-1640 with satisfactory results. The vanadium contents of water samples were also determined by FAAS for a comparison. The recovery of spiked vanadium(V) was found to be quantitative and the reproducibility was satisfactory. It was observed that the results of the SRM 1640 were in good agreement with the certified value.

Catalytic transformations of fatty acid derivatives for food, oleochemicals and fuels over carbon supported platinum group metals

Växtoljor som utgör en förnybar naturresurs används som sådana eller i modifierade former i många industriella processer, som är av stor betydelse för vårt vardagliga liv. Växtoljor används i livsmedel, i kemiska och farmaceutiska produkter, i textilindustrin, för framställning av färgämnen och beläggningsmaterial samt som miljövänliga bränslekomponenter. Fetter och oljor hör till de äldsta kemiska komponenterna som utnyttjas av människan. De består huvudsakligen av glycerolestrar och fettsyror. Fetter och oljor har typiskt en kolkedja med kol-koldubbelbindningar samt karboxyl- och estergrupper, som kan genom hydrering eller dekarboxylering konverteras till nyttiga och miljövänliga produkter med hjälp av ädelmetallkatalysatorer. Aktivt kol (C) används som bärare på katalysatorerna. Väteaddition, d.v.s. hydrering av växtoljor har varit föremål för omfattande forskning i över hundra års tid. Hydreringen är en viktig process, för den tillämpas på produktion av fetter och margarin. Omättade fettsyror hydreras traditionellt på nickelbaserade heterogena katalysatorer. Samtidigt med en partiell hydrering av fettsyrorna och fettsyraestrarna som har två dubbelbindningar pågår också isomeringsreaktioner, vilka ger cis- och transisomerer av reaktantmolekylerna. Den största nackdelen med nickelkatalysatorerna är deras giftighet samt bildning av ohälsosamma transisomerer i reaktionsprodukterna. Dessutom deaktiveras nickelkatalysatorn snabbt p.g.a. att nickeltvålar bildas i reaktionsblandningen. Platinabaserade katalysatorer lider däremot inte av dessa begränsningar. Metaller i platinagruppen i det periodiska systemet studerades i detalj för att avslöja kinetiska effekter i hydreringen av cis-metyloleat. Palladium, rutenium, rhodium, platina och iridium användes som katalytiska metaller. Metallhalten på aktivkolbärare var 1 vikt-%. De olika platinametallerna undersöktes för att kartlägga konkurrerande hydrerings- och isomeringsrutter på metallerna. Det visade sig att metallerna i andra raden av det periodiska systemet (Ru, Rh, Pd) är aktivare i isomeringsprocesserna, medan metallerna i tredje raden (Ir, Pt) har en lägre aktivitet. Pd/C valdes bland platinametallerna, för att den är attraktiv ur ekonomisk synvinkel och den är mycket aktiv och selektiv, speciellt jämfört med nickel. Tyngdpunkten i arbetet var utvecklingen av en alternativ, palladiumbaserad hydreringsteknologi som skulle ersätta den traditionella teknologin som är baserad på användningen av nickelkatalysatorer. Palladiumbaserade katalysatorer kan återcirkuleras, de är aktivare och mera resistenta mot syror och de bildar mindre mängder av skadliga transisomerer. För att denna teknologi skall bli ekonomiskt hållbar och konkurrenskraftig, måste den basera sig på de bästa möjliga katalysatorerna, vilket innebär att en optimal kombination av hög aktivitet och selektivitet samt en lång livstid för katalysatorn krävs. Därför inkluderades teknologiska aspekter kraftigt i forskningen. Mycket arbete satsades på design av palladium på en mesoporös kolbärare och undersökning av korrelationerna mellan katalysatorns egenskaper och dess aktivitet i isomeriseringsreaktionerna och i hydreringen av kol-koldubbelbindningarna i reaktantmolekylen. Katalysatorerna karakteriserades med många fysikaliska och kemiska metoder (transmissionselektronmikroskopi (TEM), röntgendiffraktion (XRD), röntgenfotoelektronspektroskopi (XPS), temperaturprogrammerad reduktion (TPR), temperaturprogrammerad desorption (TPD) av kolmonoxid, kemisorption av kolmonoxid, fysisorption av kväve). Temperaturens, vätetryckets och katalysatorkoncentrationens inverkan på fettsyra- och isomersammansättningen hos de hydrerade oljorna bestämdes under kinetiska betingelser, i frånvaro av massöverföringseffekter. Syreavspjälkning genom fullständig dekarboxylering av karboxylgruppen i fettsyramolekylen är det hittills bästa sättet att framställa miljövänlig dieselolja, eftersom linjära paraffiner fås som reaktionsprodukter och en tillsats av dyr vätgas undviks. Deoxygeneringen undersöktes systematiskt på en Pd/C-katalysator (Sibunit) genom att använda mättade fettsyror C16-C20 och C22 som råvara. Produktmolekylen blev en dieselliknande kolvätemolekyl, med en kolatom färre än i utgångsmolekylen. Lika stora dekarboxyleringshastigheter observerades för rena, mättade fettsyror. En jämförelse av deoxygenereringshastigheterna för stearin-, olein- och linolsyra som råvara vid 300oC i närvaro av 1-volymprocent väte på mesoporös Pd/C (Sibunit) avslöjade att katalysatorns aktivitet och selektivitet ökade med en ökande mättningsgrad av reaktantmolekylen. Då stearinsyra användes som utgångsmolekyl, bestod huvudprodukterna av önskade C17-kolväten, medan mängden av aromatiska C17-komponenter ökade, då olein- och linolsyra användes som utgångsmolekyler. Katalysatordeaktiveringen var relativt påfallande vid deoxygeneringen av linolsyra så att endast 3% av fettsyrorna omsattes till produkter i 330 min. Deaktiveringen orsakades av aromatiska C17-komponenter samt av fettsyradimerer, som bildades via en Diels-Alderreaktion. Hydreringen av omättade fettsyror kan därför rekommenderas som ett primärt kemiskt steg i framställningen av miljövänliga dieselprodukter. Målet var också att öka förståelsen av palladiummetallernas roll i nanoskala, speciellt effekten av metallpartiklarna i katalytisk hydrering och deoxygenering. Pd/C-katalysatorer med lika stora halter av Pd syntetiserades och metallens dispersion på bärarmaterialet varierades systematiskt genom en kontrollerad uppväxt av palladiumnanopartiklar på aktiv kolbärare. Metalldispersionens effekt på hydrerings-hastigheten och cis-transförhållandet undersöktes i detalj. En optimal metalldispersion som gav den högsta dekarboxyleringshastigheten hittades. Massöverföringens inverkan på reaktionens hastighet studerades experimentellt och temperaturprogrammerad desorption av kolmonoxid från katalysatorytan undersöktes ingående. Hydrering av växtoljor genomfördes under satsvisa och kontinuerliga betingelser. Både finfördelat Pd/C och katalysatorgranulat användes i experimenten. Ett av målen med arbetet var uppskalningen av hydreringsprocesserna. Med tanke på stora produktionsvolymer var det logiskt att undersöka kontinuerliga hydrerings- och dekarboxyleringsteknologier. En kontinuerlig packad bäddreaktor studerades i laboratorieskala, vilket gav viktig information om katalysatorns långtidsstabilitet och deaktivering. Effekten av rena fettsyror och triglycerider som råvara samt metallpartikelstorleken och palladiumhalten studerades med hjälp av den kontinuerliga reaktorn. Produktionskapaciteten som erhölls med satsvis och kontinuerlig drift jämfördes. Dekarboxyleringen av stearinsyra undersöktes också i en kontinuerlig packad bädd. Omsättningsgraden blev 15% för en stabil katalysator.

Pulsed corona discharge as an advanced oxidation process for degradation of organic

Advanced oxidation processes (AOPs) have been studied and developed to suffice the effective removal of refractory and toxic compounds in polluted water. The quality and cost of wastewater treatment need improvements, and electric discharge technology has a potential to make a significant difference compared to other established AOPs based on energy efficiency. The generation of active oxidant species such as ozone and hydroxyl radicals by high voltage discharge is a relatively new technology for water treatment. Gas-phase pulsed corona discharge (PCD), where a treated aqueous solution is dispersed between corona-producing electrodes free of the dielectric barriers, was developed as an alternative approach to the problem. The short living radicals and ozone formed in the gas phase and at the gas-liquid interface react with dissolved impurities. PCD equipment has a relatively simple configuration, and with the reactor in an enclosed compartment, it is insensitive towards gas humidity and does not need the gas transport. In this thesis, PCD was used to study and evaluate the energy efficiency for degrading various organic compounds, as well as the chemistry of the oxidation products formed. The experiments investigate the aqueous oxidation of phenol, humic substances, pharmaceutical compounds (paracetamol, ibuprofen, indomethacin, salicylic acids, -estradiol), as well as lignin degradation and transformation to aldehydes. The study aims to establish the influence of initial concentration of the target pollutant, the pulsed discharge parameters, gas phase composition and the pH on the oxidation kinetics and the efficiency. Analytical methods to measure the concentrations of the target compounds and their by-products include HPLC, spectrophotometry, TOC and capillary electrophoresis. The results of the research included in this summary are presented in the attached publications and manuscripts accepted for publication. Pulsed corona discharge proved to be highly effective in oxidizing each of the target compounds, surpassing the closest competitor, conventional ozonation. The increase in oxidation efficiencies for some compounds in oxygen media and at lower pulse repetition frequencies shows a significant role of ozone. The role of the ·OH radicals was established in the surface reactions. The main oxidation products, formation of nitrates, and the lignin transformation were quantified. A compound specific approach is suggested for optimization of the PCD parameters that have the most significant impact on the oxidation energy efficiency because of the different characteristics and responses of the target compound to the oxidants, as well as different admixtures that are present in the wastewater. Further studies in the method’s safety (nitration and nitrosation of organic compounds, nitrite and nitrate formation enhancement) are needed for promoting the method.

Imidazolinone Degradation in Soil in Response to Application History

Accelerated herbicide degradation consists in its faster degradation in areas where it has been previously applied, due to the adaptation of microbial population to that particular compound. Accelerated degradation can reduce herbicide persistence and reduce its efficacy in soil. The objective of this study was to investigate if imidazolinone herbicides have enhanced microbial degradation in rice paddy soils. A laboratory experiment was conducted, evaluating the CO2 evolution rate from soils with and without history of herbicide application (imazapyr + imazapic and imazethapyr + imazapic), incubated with imidazolinone herbicides: imazethapyr, imazapyr, imazapic, imazamethabenz, imazamox and an untreated check. The amount of CO2 released from the soil was measured. As a result, the prior application of imidazolinones does not stimulate microbial degradation of herbicides from the same chemical group.

Fructan degradation and hydrolytic activity in tuberous roots of Viguiera discolor Baker (Asteraceae), a herbaceous species from the cerrado

Fructans of the inulin type are the major reserve carbohydrates in tuberous roots of Viguiera discolor, a perennial herb native to the cerrado. Changes in molecular mass of the polymer, followed by releasing free fructose suggested that hydrolysis could be related to the sprouting of the buds after the dormant period, when aerial parts of the plant are naturally absent. Excision of aerial parts resulted in the increase of fructan 1-exohydrolase (1-FEH) activity in tuberous roots after sprouting. 1-FEH was partially purified from this material by binding to ConA-Sepharose and the highest activity was detected at pH 5.4 and between 20 and 40 °C. Values of Km for V. discolor inulin could not be determined since no saturation was observed up to 10%. The study of the kinetics of the 1-FEH activity showed that it does not follow Michaelis-Menten and apparently presents allosteric behaviour, as data fits in the Hill equation. The 1-FEH from V. discolor is a glycoprotein, more active on low molecular mass fructans than on high molecular mass inulin from the same species.

Large-scale production and purification of recombinant protein from an insect cell/baculovirus system in Erlenmeyer flasks: application to the chicken poly(ADP-ribose) polymerase catalytic domain

A simple and inexpensive shaker/Erlenmeyer flask system for large-scale cultivation of insect cells is described and compared to a commercial spinner system. On the basis of maximum cell density, average population doubling time and overproduction of recombinant protein, a better result was obtained with a simpler and less expensive bioreactor consisting of Erlenmeyer flasks and an ordinary shaker waterbath. Routinely, about 90 mg of pure poly(ADP-ribose) polymerase catalytic domain was obtained for a total of 3 x 109 infected cells in three liters of culture