Ultrasonic versus high-speed cavity preparation: Analysis of increases in pulpal temperature and time to complete preparation

Statement of problem. The use of ultrasonic tips has become an alternative for cavity preparation. However, there are concerns about this type of device, particularly with respect to intrapulpal temperatures and cavity preparation time.Purpose. The purpose of this study was to analyze pulpal temperature increases generated by an ultrasonic cavity preparation with chemical vapor deposition (CVD) tips, in comparison to preparation with a high-speed handpiece with a diamond rotary cutting instrument. The time required to complete the cavity preparation with each system was also evaluated.Material and methods. Thermocouples were positioned in the pulp chamber of 20 extracted human third molars. Slot-type cavities (3 x 3 x 2 mm) were prepared on the buccal and the lingual surfaces of each tooth. The test groups were: high-speed cavity preparation with diamond rotary cutting instruments (n = 20) and ultrasonic cavity preparation with CVD points (n = 20). During cavity preparation, the increases In pulpal temperature, and the time required for the preparation, were recorded and analyzed by Student's t test for paired samples (alpha = .05).Results. The average pulpal temperature increases were 4.3 degrees C for the high-speed preparation and 3.8 degrees C for the ultrasonic preparation, which were statistically similar (P = .052). However, significant differences were found (P < .001) for the time expended (3.3 minutes for the high-speed bur and 13.77 minutes for the ultrasound device).Conclusions. The intrapulpal temperatures produced during cavity preparation by ultrasonic tips versus high-speed bur preparation were similar. However, the use of the ultrasonic device required 4 times longer for the completion of a cavity preparation.

Morphology of eggs of Dioctophyme renale Goeze, 1782 (Nematoda: Dioctophymatidae) and influences of temperature on development of first-stage larvae in the eggs

Este estudo teve a finalidade de fornecer dados morfológicos de ovos de D. renale e do desenvolvimento de larvas de primeiro estádio em ovos mantidos em diferentes temperaturas. Os ovos foram obtidos por centrífugação da urina de cães parasitados e colocados em placas de Petri em estufa BOD, durante 90 dias. O experimento consistiu de três tratamentos (GI - 15 ºC, GII - 20 ºC e GIII - 26 ºC) com cinco repetições cada. Os ovos apresentaram tamanho médio de 67,23 x 42,78 µm, e o tempo médio de incubação foi inversamente proporcional à temperatura de incubação e as larvas apresentaram motilidade por aproximadamente uma semana após sua formação.

Effect of temperature on the interaction between the nonionic surfactant C(12)E(5) and poly(ethylene oxide) investigated by dynamic light scattering and fluorescence methods

The interaction between the nonionic surfactant C(12)E(5) and a high molar mass (M = 5.94 x 10(5)) poly(ethylene oxide) (PEG) in aqueous solution has been examined as a function of temperature by dynamic light scattering and fluorescence methods over a broad concentration range. Clusters of small surfactant micelles form within the PEO coil, leading to its extension. The hydrodynamic radius of the complex increases strongly with temperature as well as with the concentrations of surfactant and polymer. At high concentrations of the surfactant, the coil/micellar cluster complex coexists with free C(12)E(5) micelles in the solution. Fluorescence quenching measurements show a moderate micellar growth from 155 to 203 monomers in PEO-free solutions of C(12)E(5) over a wide concentration range (0.02-2.5%) at 8 degrees C. Below 0.25% C(12)E(5), the average aggregation number (N) of the micelles is smaller in the presence of PEO than in its absence. However, N increases with increasing surfactant concentration up to a plateau value of about 270 at about 1.2% (ca. 30 mM) C(12)E(5). At high surfactant concentrations, N is larger in the presence of polymer than in its absence, a finding which is connected to a significant lowering of the clouding temperature due to the PEO at these compositions. Similar results of increasing aggregation number followed by a plateau were also found at a fixed concentration of surfactant (2.5%) and varied PEO.

Effect of the temperature on the TMOS sono-hydrolysis and a study of the structure of the resulting aged sonogels

The effect of temperature on the oxalic acid catalyzed sono-hydrolysis of tetramethoxysilane (TMOS) was studied by means of a heat flux calorimetric method. The activation energy of the process was measured as (24.5 +/- 0.8) kJ/mol in the temperature range between 10 and 50 degreesC. The structural characteristics of the resulting sonogels, after long period of aging in saturated conditions, were studied by means of small angle X-ray scattering. The structure can be described as formed by similar to2.7 nm mean size mass fractal-like aggregates (clusters) of primary silica particles of similar to0.3 nm mean size, all imbibed in a liquid phase. The average mass fractal dimension of the clusters was found to be 2.58. The primary particle density was estimated as 2.23 g/cm(3), in good agreement with the value frequently quoted for fused silica. The volume fraction of the clusters, in the saturated sonogels was estimated as about 28%. The moment in which the meniscus of the liquid phase penetrates into the clusters under rapid evaporation process has been detected by an inflection in the first derivative of the curve of weight loss in a simple thermogravimetric test. (C) 2003 Elsevier B.V. All rights reserved.

Pupae storage effect of Cotesia flavipes (Cameron, 1891) (Hymenoptera: Braconidae) in low temperature.

The study was developed in the 'Laboratorio de Biologia e Criacao de Insetos' (LBCI), 'Faculdade de Ciencias Agrarias e Veterinarias (FCAV), 'Universidade Estadual Paulista' (Unesp), Jaboticabal, SP, with objective of evaluating the pupae storage effect of Cotesia flavipes in low temperature (medium temperature = 2,75[degree]C). The experiment was made up of 13 treatments: fi, 1, 2, 3, 4, 5, 6, 7, 8, 9.10 and 11 masses storage days of pupae in refrigerator temperature and the check was man maintained on 25[plus or minus]2[degree]C and relative humidity of 70[plus or minus]10%. The next generation of parasitoid also was analyzed, maintained to 25[plus or minus]2[degree]C during all development. It was evaluated: period and pupae viability; average number, longevity and adults' sex ratio of the stored generation and period egg-larvae; period and pupae viability: average number, longevity and adults' sex ratio of the next generation. It verified that the pupae storage of C. flavipes in refrigerator temperature for until 5 days does not affect its development and the stored generation, suggesting the utilization possibility of this resource in mass rearing of this insect.

Experimental and theoretical study of workpiece temperature when end milling hardened steels using (TiAl)N-coated and PcBN-tipped tools

The present work shows an experimental and theoretical study on heat flow when end milling, at high-speed, hardened steels applied to moulds and dies. AISI H13 and AISI D2 steels were machined with two types of ball nose end mills: coated with (TiAl)N and tipped with PcBN. The workpiece geometry was designed to simulate tool-workpiece interaction in real situations found in mould industries, in which complex surfaces and thin walls are commonly machined. The compressed and cold air cooling systems were compared to dry machining Results indicated a relatively small temperature variation, with higher range when machining AISI D2 with PcBN-tipped end mill. All cooling systems used demonstrated good capacity to remove heat from the machined surface, especially the cold air. Compressed air was the most indicated to keep workpiece at relatively stable temperature. A theoretical model was also proposed to estimate the energy transferred to the workpiece (Q) and the average convection coefficient ((h) over bar) for the cooling systems used. The model used a FEM simulation and a steepest decent method to find the best values for both variables. (c) 2007 Elsevier B.V. All rights reserved.

Influence of temperature on larval survival, development and respiration in Chasmagnathus granulata (Crustacea, Decapoda)

Larvae of an estuarine grapsid crab Chasmagnathus granulata Dana 1851, from temperate and subtropical regions of South America, were reared in seawater (32 ‰) at five different constant temperatures (12, 15, 18, 21, 24 °C). Complete larval development from hatching (Zoea I) to metamorphosis (Crab I) occurred in a range from 15 to 24 °C. Highest survival (60% to the first juvenile stage) was observed at 18°C, while all larvae reared at 12°C died before metamorphosis. The duration of development (D) decreased with increasing temperature (T). This relationship is described for all larval stages as a power function (linear regressions after logarithmic transformation of both D and T). The temperature-dependence of the instantaneous developmental rate (D-1) is compared among larval stages and temperatures using the Q10 coefficient (van't Hoff's equation). Through all four zoeal stages, this index tends to increase during development and to decrease with increasing T (comparing ranges 12-18, 15-21, 18-24 °C). In the Megalopa, low Q10 values were found in the range from 15 to 24 °C. In another series of experiments, larvae were reared at constant 18°C and their dry weight (W) and respiratory response to changes in T were measured in all successive stages during the intermoult period (stage C) of the moulting cycle. Both individual and weight-specific respiration (R, QO2) increased exponentially with increasing T. At each temperature, R increased significantly during growth and development through successive larval stages. No significantly different QO2 values were found in the first three zoeal stages, while a significant decrease with increasing W occurred in the Zoea IV and Megalopa. As in the temperature-dependence of D, the respiratory response to changes in temperature (Q10) depends on both the temperature range and the developmental stage, however, with different patterns. In the zoeal stages, the respiratory Q10 was minimum (1.7-2.2) at low temperatures (12-18 °C), but maximum (2.2-3.0) at 18-24 °C. The Megalopa, in contrast, showed a stronger metabolic response in the lower than in the upper temperature range (Q10 = 2.8 and 1.7, respectively). We interpret this pattern as an adaptation to a sequence of temperature conditions that should typically be encountered by C. granulata larvae during their ontogenetic migrations: hatching in and subsequent export from shallow estuarine lagoons, zoeal development in coastal marine waters, which are on average cooler, return in the Megalopa stage to warm lagoons. We thus propose that high metabolic sensitivity to changes in temperature may serve as a signal stimulating larval migration, so that the zoeae should tend to leave warm estuaries and lagoons, whereas the Megalopa should avoid remaining in the cooler marine waters and initiate its migration towards shallow coastal lagoons.

Effect of temperature on development and population growth of Acarophenax lacunatus (Cross and Krantz) (Prostigmata: Acarophenacidae) on Rhyzopertha dominica (F.) (Coleoptera: Bostrichidae)

The parasitic mite Acarophenax lacunatus kills the eggs upon which it feeds and seems to have potential as a biological control agent of stored grain pests. The lack of biological studies on this mite species led to the present study carried out in laboratory conditions at eight different temperatures (ranging from 20 to 41°C) and 60% relative humidity using Rhyzopertha dominica as host. The higher the temperature, the faster: (1) the attachment of female mites to the host egg (varying from 1 to 5 h); (2) the increase in body size of physogastric females (about twice faster at 40°C than at 20°C); and (3) the generation time (ranging from 40 to 220 h). In addition, the higher the temperature, the shorter the maximum female longevity (ranging from about 75 to 300 h). The two estimated temperature thresholds for development of A. lacunatus on R. dominica were 18 and 40°C. The average number of female and male offspring per gravid mite were 12.8 and 1.0, respectively, with sex ratios (females/total) ranging from 0.91 to 0.94 (maximum at 30°C). The net reproductive rate and intrinsic rate of increase also presented maximum values at 30°C (12.1 and 0.04, respectively).

Alterations in chlorophyll a fluorescence, pigment concentrations and lipid peroxidation to chilling temperature in coffee seedlings

Coffea arabica L. is considered to be sensitive to low temperatures throughout its life cycle. In some Brazilian regions, seedling production occurs under shade conditions and during the winter, with average temperatures of around 10 °C. The formation and functioning of the photosynthetic apparatus are strongly controlled by temperature. This study aimed to assess the changes that occurred in pigment contents, lipid peroxidation and variables of chlorophyll a fluorescence during the greening process of coffee seedlings submitted to chilling. Results indicate that saturation of the photosynthetic activity of coffee seedlings occurred before saturation of the accumulation of chloroplastid pigments. Pigment accumulation during the greening process is far beyond the metabolic needs for the maintenance of photosynthetic activity, more specifically of photosystem II. Coffee seedlings attained a quantum yield equivalent to that of the control with approximately half the chlorophyll a and b contents and around 40% of the carotenoid. Low temperature decreases the metabolism of seedlings, consequently reducing free radical production and lipid peroxidation. The chilling temperature (10 °C) used inhibited the accumulation of chloroplast pigments, in turn altering the capacity of the photosynthetic tissue of etiolated coffee seedlings to capture and transfer photon energy to the photosystem II reaction centre. These alterations were better demonstrated by O-J-I-P chlorophyll a fluorescence transients, rather than F v/F m and F v/F 0 ratios. © 2009 Elsevier B.V. All rights reserved.

The relationships between scrotal surface temperature, age and sperm quality in stallions

In horses, spermatogenesis normally occurs at an average intratesticular temperature of 35. °C; therefore, mechanisms for testicular thermoregulation are essential. Measuring the scrotal surface temperature by thermography is one of the methodologies used to evaluate the effectiveness of testicular thermoregulation. The objective of this study was to determine the relationship between the control of scrotal surface temperature and sperm quality in horses of different ages. In total, 24 Quarter Horse stallions were divided into three groups: YS (young stallions), AS (adult stallions) and OS (old stallions). Initially, we calculated the testicular volume (TV) and evaluated various aspects of the semen (sperm kinetics, plasma membrane integrity and sperm morphology) for all the animals. We also evaluated rectal temperature (RT), body surface temperature (BST,) and average scrotal surface temperature in the testicular region (SST) before (M0) and after sun exposure (M1). Differences were observed (p<0.05) between the RT and BST before and after sun exposure in all three groups. However, there were no differences (p>0.05) in the SST values at these two time points, thus demonstrating the efficiency of the mechanisms for testicular thermoregulation. The SST was similar (p>0.05) among all three groups. Based on these results, we conclude that fertile stallions of different age groups are able to maintain SST and measuring the heat radiating from the scrotum using a digital infrared thermographer. We can also conclude that measuring the heat radiating from the scrotum using a digital infrared thermographer is a practical and efficient tool for monitoring SST in horses. © 2013 Elsevier B.V.

Effect of feeding whole linseed as a source of polyunsaturated fatty acids on performance and egg characteristics of laying hens kept at high ambient temperature

The present study was conducted to evaluate the effects of feeding whole linseed on the laying performance and egg characteristics in laying hens kept at high ambient environmental temperatures (average 34 degrees C; the diurnal temperature range 26 degrees C to 41 degrees C). Two hundred and forty 38-wk-old white Leghorn laying hens were fed diets containing 0, 5, 10 or 15% whole linseed (as a source of n-3 polyunsaturated fatty acids) for a period of 12 weeks. Egg production was recorded daily, while feed intake and egg characteristics were monitored on weekly basis. The results of the study demonstrated that egg production and feed intake decreased, while feed conversion ratio (FCR) per dozen of eggs increased (p <= 0.05) with increasing dietary linseed levels. Egg weight, yolk weight, albumen height, eggshell weight, and eggshell thickness were not influenced (p > 0.05) by linseed levels in the diets offered to the laying hens. The results of the present trial suggest that feeding linseed to the laying hens in hot climates has no detrimental effects on egg characteristics, but has suppressive effects on egg production, feed intake and feed efficiency of laying hens.

Chemometric optimization of solid-liquid extraction with low-temperature partition (SLE-LTP) for determination of persistent organic pollutants in Caiman yacare eggs

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Temperature and storage period over spermatic parameters of jundia, Rhamdia quelen (Quoy & Gaimard, 1824)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estimating the average length of hospitalization due to pneumonia: a fuzzy approach

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Study of temperature variation in cortical bone during osteotomies with trephine drills

The purpose of this study was to compare temperature variation during osteotomies with trephine drills under different irrigation conditions: without irrigation, external irrigation, and double irrigation.Synthetic blocks of bone (type I density) were used for drilling procedures with an experimental computed machine, which measured the maximum temperature in the cortical bone during osteotomy with a bone cut that was 5 mm in both diameter and depth. Three groups were formed depending on the irrigation conditions: no irrigation (G1), external irrigation (G2), and double irrigation (G3). Fifty drillings were performed for each group.The average thermal increase in the groups was 21.7 +/- 1.52 A degrees C in G1, 14.2 A +/- 0.70 A degrees C in G2, and 12.4 A +/- 0.75 A degrees C in G3. The results presented statistically significant differences among all groups (alpha = 0.05).The double irrigation technique resulted in a smaller increase in temperature in the cortical bone model, demonstrating a greater efficiency, which may be beneficial when compared to external irrigation alone.The trephine has been widely used in removing small blocks for bone graft, especially the posterior mandible, where the possibility of heating may be higher due to the density of cortical bone in this area. So it is important that the professionals select instruments that can reduce the risks of complications in the proposed treatment.