Hydrodynamic induced by an array of wave energy converters. Experimental and numerical analysis

The thesis analyses the hydrodynamic induced by an array of Wave energy Converters (WECs), under an experimental and numerical point of view. WECs can be considered an innovative solution able to contribute to the green energy supply and –at the same time– to protect the rear coastal area under marine spatial planning considerations. This research activity essentially rises due to this combined concept. The WEC under exam is a floating device belonging to the Wave Activated Bodies (WAB) class. Experimental data were performed at Aalborg University in different scales and layouts, and the performance of the models was analysed under a variety of irregular wave attacks. The numerical simulations performed with the codes MIKE 21 BW and ANSYS-AQWA. Experimental results were also used to calibrate the numerical parameters and/or to directly been compared to numerical results, in order to extend the experimental database. Results of the research activity are summarized in terms of device performance and guidelines for a future wave farm installation. The device length should be “tuned” based on the local climate conditions. The wave transmission behind the devices is pretty high, suggesting that the tested layout should be considered as a module of a wave farm installation. Indications on the minimum inter-distance among the devices are provided. Furthermore, a CALM mooring system leads to lower wave transmission and also larger power production than a spread mooring. The two numerical codes have different potentialities. The hydrodynamics around single and multiple devices is obtained with MIKE 21 BW, while wave loads and motions for a single moored device are derived from ANSYS-AQWA. Combining the experimental and numerical it is suggested –for both coastal protection and energy production– to adopt a staggered layout, which will maximise the devices density and minimize the marine space required for the installation.

Design of a GNSS receiver for the ESEO mission

This thesis was carried out inside the ESA's ESEO mission and focus in the design of one of the secondary payloads carried on board the spacecraft: a GNSS receiver for orbit determination. The purpose of this project is to test the technology of the orbit determination in real time applications by using commercial components. The architecture of the receiver includes a custom part, the navigation computer, and a commercial part, the front-end, from Novatel, with COCOM limitation removed, and a GNSS antenna. This choice is motivated by the goal of demonstrating the correct operations in orbit, enabling a widespread use of this technology while lowering the cost and time of the device’s assembly. The commercial front-end performs GNSS signal acquisition, tracking and data demodulation and provides raw GNSS data to the custom computer. This computer processes this raw observables, that will be both transferred to the On-Board Computer and then transmitted to Earth and provided as input to the recursive estimation filter on-board, in order to obtain an accurate positioning of the spacecraft, using the dynamic model. The main purpose of this thesis, is the detailed design and development of the mentioned GNSS receiver up to the ESEO project Critical Design Review, including requirements definition, hardware design and breadboard preliminary test phase design.

Studio di fattibilità di una nuova tipologia di argano per il sollevamento di carichi nel settore off-shore

Studio di una nuova tipologia di argano per il sollevamento di carichi nel settore off-shore. In particolare, un argano funzionalmente identico ad uno in fase di realizzazione in azienda è stato modellato al CAD 3D e verificato strutturalmente utilizzando Ansys Workbench, software adatto per analisi F.E.M.. Ottenuti i risultati, ne è stato fatto un confronto con quelli relativi all'argano esistente (argano di ‟Moho‟); nello specifico sono stati comparati gli stress ottenuti nelle varie parti dei due argani (tamburo, spalla, flange, alette di rinforzo, albero) in seguito all‟applicazione di 4 casi di carico differenti (E‟, E‟‟, P‟, P‟‟).

Entwicklung eines schnellen, piezobasierten Frequenztuners für supraleitende CH-Kavitäten

Im Rahmen der vorliegenden Arbeit wurde ein schnelles, piezobasiertes Frequenztuningsystem für aktuelle sowie zukünftige supraleitende (sl) CH-Kavitäten entwickelt. Die Grundlage des hierbei verwendeten Tuningkonzepts unterscheidet sich von bisherigen, konventionellen Tuningmethoden supraleitender Kavitäten grundlegend. Zum Ausgleichen von unerwünschten Frequenzverstimmungen während des Beschleunigerbetriebes werden sogenannte bewegliche Balgtuner in das Innere der Resonatorgeometrie geschweißt. Aufgrund ihrer variablen Länge können diese die Kapazität der Kavität und somit die Resonanzfrequenz gezielt beeinflussen. Die Antriebsmechanik, die für die Auslenkung bzw. Stauchung der Balgtuner sorgt, besteht aus einer langsamen, schrittmotorbetriebenen und einer schnellen, piezobasierten Tuningeinheit, welche auf der Außenseite des Heliummantels der jeweiligen CH-Kavität installiert wird. Zur Überprüfung dieses neuartigen Tuningkonzepts wurde in der Werkstatt des Instituts für Angewandte Physik (IAP) der Goethe Universität Frankfurt ein Prototyp der gesamten Tuningeinheit aus Edelstahl gefertigt. Die Funktionsweise der langsamen sowie schnellen Tuningeinheit konnten hierbei in ersten Messungen bei Raumtemperatur erfolgreich getestet werden. Somit stellt die in dieser Arbeit entwickelte Tuningeinheit eine vielversprechende Möglichkeit des dynamischen Frequenztunings supraleitender CH-Strukturen dar. rnDes Weiteren wurden im Rahmen der Arbeit mit Hilfe der Simulationsprogramme ANSYS Workbench sowie CST MicroWave Studio gekoppelte strukturmechanische und elektromagnetische Simulationen der sl 217 MHz CH sowie der sl 325 MHz CH-Kavität durchgeführt. Hierbei konnte zum einen der Frequenzbereich und somit der notwendige mechanische Hub der jeweiligen Tuningeinheit durch Bestimmung der Frequenzverstimmungen signifikant reduziert werden. Zum anderen war es möglich, die mechanische Stabilität der beiden Kavitäten zu untersuchen und somit plastische Deformationen von vornherein auszuschließen. Zur Überprüfung der Genauigkeit sämtlicher getätigter Simulationsrechnungen wurde das strukturmechanische Verhalten in Abhängigkeit äußerer Einflüsse und die daraus resultierenden Frequenzverstimmungen der CH-Kavitäten sowohl bei Raumtemperatur als auch bei kryogenen Temperaturen von 4.2 K gemessen. Hierbei zeigten sich zum Teil hervorragende Übereinstimmungen zwischen den simulierten und gemessenen Werten mit Diskrepanzen von unter 10%. Mit Hilfe dieser Ergebnisse konnte gezeigt werden, dass die gekoppelte Simulation ein essentielles Werkzeug während der Entwicklungsphase einer supraleitenden Beschleunigungsstruktur darstellt, so dass die für den Betrieb erforderliche mechanische Stabilität einer supraleitenden Kavität erreicht werden kann. rn

FEM and experimental analysis of a wind turbine blade

This paperwork compares the a numerical validation of the finite element model (FEM) with respect the experimental tests of a new generation wind turbine blade designed by TPI Composites Inc. called BSDS (Blade System Design Study). The research is focused on the analysis by finite element (FE) of the BSDS blade and its comparison with respect the experimental data from static and dynamic investigations. The goal of the research is to create a general procedure which is based on a finite element model and will be used to create an accurate digital copy for any kind of blade. The blade prototype was created in SolidWorks and the blade of Sandia National Laboratories Blade System Design Study was accurately reproduced. At a later stage the SolidWorks model was imported in Ansys Mechanical APDL where the shell geometry was created and modal, static and fatigue analysis were carried out. The outcomes of the FEM analysis were compared with the real test on the BSDS blade at Clarkson University laboratory carried out by a new procedures called Blade Test Facility that includes different methods for both the static and dynamic test of the wind turbine blade. The outcomes from the FEM analysis reproduce the real behavior of the blade subjected to static loads in a very satisfying way. A most detailed study about the material properties could improve the accuracy of the analysis.

Progetto preliminare ed analisi strutturale di un Cubesat

Lo scopo di questa tesi è progettare e analizzare la struttura più efficiente ed adeguata di un CubeSat 1U, realizzando un modello al calcolatore che sia il più possibile aderente al modello reale. Ciò viene fatto utilizzando un software dedicato alle simulazioni avanzate, Ansys Workbench con il quale è possibile svolgere analisi modali sulla struttura realizzata. Per validare il modello numerico occorre confrontare i risultati ottenuti al calcolatore con quelli conseguiti sperimentalmente nell'ambito della tesi del mio collega Riccardo Fabbri; una volta fatto ciò si manipola il modello numerico finché i risultati non si matchano, entro un certo margine di errore. Un modello numerico del genere è fondamentale per le fasi iniziali di qualsiasi progetto sperimentale volto alla costruzione di una struttura, infatti consente di svolgere tutta una serie di test e simulazioni di carichi e vincoli che nella realtà non si possono eseguire per via di numerosi fattori, come ad esempio la mancanza della strumentazione adeguata.

Structural capacity of steel tubular cast-in-place piling

Steel tubular cast-in-place pilings are used throughout the country for many different project types. These piles are a closed-end pipe with varying wall thicknesses and outer diameters, that are driven to depth and then the core is filled with concrete. These piles are typically used for smaller bridges, or secondary structures. Mostly the piling is designed based on a resistance based method which is a function of the soil properties of which the pile is driven through, however there is a structural capacity of these members that is considered to be the upper bound on the loading of the member. This structural capacity is given by the AASHTO LRFD (2010), with two methods. These two methods are based on a composite or non-composite section. Many state agencies and corporations use the non-composite equation because it is requires much less computation and is known to be conservative. However with the trends of the time, more and more structural elements are being investigated to determine ways to better understand the mechanics of the members, which could lead to more efficient and safer designs. In this project, a set of these piling are investigated. The way the cross section reacts to several different loading conditions, along with a more detailed observation of the material properties is considered as part of this research. The evaluation consisted of testing stub sections of pile with varying sizes (10-¾”, 12-¾”), wall thicknesses (0.375”, 0.5”), and testing methods (whole compression, composite compression, push through, core sampling). These stub sections were chosen as they would represent a similar bracing length to many different soils. In addition, a finite element model was developed using ANSYS to predict the strains from the testing of the pile cross sections. This model was able to simulate the strains from most of the loading conditions and sizes that were tested. The bond between the steel shell and the concrete core, along with the concrete strength through the depth of the cross section were some of the material properties of these sections that were investigated.

Ontologies and Methods for Interoperability of Engineering Analysis Models (EAMS) in an E-Design Environment

ABSTRACT ONTOLOGIES AND METHODS FOR INTEROPERABILITY OF ENGINEERING ANALYSIS MODELS (EAMS) IN AN E-DESIGN ENVIRONMENT SEPTEMBER 2007 NEELIMA KANURI, B.S., BIRLA INSTITUTE OF TECHNOLOGY AND SCIENCES PILANI INDIA M.S., UNIVERSITY OF MASSACHUSETTS AMHERST Directed by: Professor Ian Grosse Interoperability is the ability of two or more systems to exchange and reuse information efficiently. This thesis presents new techniques for interoperating engineering tools using ontologies as the basis for representing, visualizing, reasoning about, and securely exchanging abstract engineering knowledge between software systems. The specific engineering domain that is the primary focus of this report is the modeling knowledge associated with the development of engineering analysis models (EAMs). This abstract modeling knowledge has been used to support integration of analysis and optimization tools in iSIGHT FD , a commercial engineering environment. ANSYS , a commercial FEA tool, has been wrapped as an analysis service available inside of iSIGHT-FD. Engineering analysis modeling (EAM) ontology has been developed and instantiated to form a knowledge base for representing analysis modeling knowledge. The instances of the knowledge base are the analysis models of real world applications. To illustrate how abstract modeling knowledge can be exploited for useful purposes, a cantilever I-Beam design optimization problem has been used as a test bed proof-of-concept application. Two distinct finite element models of the I-beam are available to analyze a given beam design- a beam-element finite element model with potentially lower accuracy but significantly reduced computational costs and a high fidelity, high cost, shell-element finite element model. The goal is to obtain an optimized I-beam design at minimum computational expense. An intelligent KB tool was developed and implemented in FiPER . This tool reasons about the modeling knowledge to intelligently shift between the beam and the shell element models during an optimization process to select the best analysis model for a given optimization design state. In addition to improved interoperability and design optimization, methods are developed and presented that demonstrate the ability to operate on ontological knowledge bases to perform important engineering tasks. One such method is the automatic technical report generation method which converts the modeling knowledge associated with an analysis model to a flat technical report. The second method is a secure knowledge sharing method which allocates permissions to portions of knowledge to control knowledge access and sharing. Both the methods acting together enable recipient specific fine grain controlled knowledge viewing and sharing in an engineering workflow integration environment, such as iSIGHT-FD. These methods together play a very efficient role in reducing the large scale inefficiencies existing in current product design and development cycles due to poor knowledge sharing and reuse between people and software engineering tools. This work is a significant advance in both understanding and application of integration of knowledge in a distributed engineering design framework.

Prediction of bendig load capacity of timber beams by finite element method simulation of knots and grain deviation

A finite element model was used to simulate timberbeams with defects and predict their maximum load in bending. Taking into account the elastoplastic constitutive law of timber, the prediction of fracture load gives information about the mechanisms of timber failure, particularly with regard to the influence of knots, and their local graindeviation, on the fracture. A finite element model was constructed using the ANSYS element Plane42 in a plane stress 2D-analysis, which equates thickness to the width of the section to create a mesh which is as uniform as possible. Three sub-models reproduced the bending test according to UNE EN 408: i) timber with holes caused by knots; ii) timber with adherent knots which have structural continuity with the rest of the beam material; iii) timber with knots but with only partial contact between knot and beam which was artificially simulated by means of contact springs between the two materials. The model was validated using ten 45 × 145 × 3000 mm beams of Pinus sylvestris L. which presented knots and graindeviation. The fracture stress data obtained was compared with the results of numerical simulations, resulting in an adjustment error less of than 9.7%

Simulation of Freight Trains Equipped with Partially Filled Tank Containers and Related Resonance Phenomenon

To study the fluid motion-vehicle dynamics interaction, a model of four, liquid filled two-axle container freight wagons was set up. The railway vehicle has been modelled as a multi-body system (MBS). To include fluid sloshing, an equivalent mechanical model has been developed and incorporated. The influence of several factors has been studied in computer simulations, such as track defects, curve negotiation, train velocity, wheel wear, liquid and solid wagonload, and container baffles. SIMPACK has been used for MBS analysis, and ANSYS for liquid sloshing modelling and equivalent mechanical systems validation. Acceleration and braking manoeuvres of the freight train set the liquid cargo into motion. This longitudinal sloshing motion of the fluid cargo inside the tanks initiated a swinging motion of some components of the coupling gear. The coupling gear consists of UIC standard traction hooks and coupling screws that are located between buffers. One of the coupling screws is placed in the traction hook of the opposite wagon thus joining the two wagons, whereas the unused coupling screw rests on a hanger. Simulation results showed that, for certain combinations of type of liquid, filling level and container dimensions, the liquid cargo could provoke an undesirable, although not hazardous, release of the unused coupling screw from its hanger. The coupling screw's release was especially obtained when a period of acceleration was followed by an abrupt braking manoeuvre at 1 m/s2. It was shown that a resonance effect between the liquid's oscillation and the coupling screw's rotary motion could be the reason for the coupling screw's undesired release. Possible solutions to avoid the phenomenon are given.Acceleration and braking manoeuvres of the freight train set the liquid cargo into motion. This longitudinal sloshing motion of the fluid cargo inside the tanks initiated a swinging motion of some components of the coupling gear. The coupling gear consists of UIC standard traction hooks and coupling screws that are located between buffers. One of the coupling screws is placed in the traction hook of the opposite wagon thus joining the two wagons, whereas the unused coupling screw rests on a hanger. This paper reports on a study of the fluid motion-train vehicle dynamics interaction. In the study, a model of four, liquid-filled two-axle container freight wagons was developed. The railway vehicle has been modeled as a multi-body system (MBS). To include fluid sloshing, an equivalent mechanical model has been developed and incorporated. The influence of several factors has been studied in computer simulations, such as track defects, curve negotiation, train velocity, wheel wear, liquid and solid wagonload, and container baffles. A simulation program was used for MBS analysis, and a finite element analysis program was used for liquid sloshing modeling and equivalent mechanical systems validation. Acceleration and braking maneuvers of the freight train set the liquid cargo into motion. This longitudinal sloshing motion of the fluid cargo inside the tanks initiated a swinging motion of some components of the coupling gear. Simulation results showed that, for certain combinations of type of liquid, filling level and container dimensions, the liquid cargo could provoke an undesirable, although not hazardous, release of an unused coupling screw from its hanger. It was shown that a resonance effect between the liquid's oscillation and the coupling screw's rotary motion could be the reason for the coupling screw's undesired release. Solutions are suggested to avoid the resonance problem, and directions for future research are given.

Simulation model for the study of overhead rail current collector systems dynamics, focused on the design of a new conductor rail

Overhead rigid conductor arrangements for current collection for railway traction have some advantages compared to other, more conventional, energy supply systems. They are simple, robust and easily maintained, not to mention their flexibility as to the required height for installation, which makes them particularly suitable for use in subway infrastructures. Nevertheless, due to the increasing speeds of new vehicles running on modern subway lines, a more efficient design is required for this kind of system. In this paper, the authors present a dynamic analysis of overhead conductor rail systems focused on the design of a new conductor profile with a dynamic behaviour superior to that of the system currently in use. This means that either an increase in running speed can be attained, which at present does not exceed 110 km/h, or an increase in the distance between the rigid catenary supports with the ensuing saving in installation costs. This study has been carried out using simulation techniques. The ANSYS programme has been used for the finite element modelling and the SIMPACK programme for the elastic multibody systems analysis.

Teaching Magnetic Design using CAD tools

Design of magnetic components is a multivariable problem. There are many different combinations of shapes, sizes and materials for the core with many diameters for the wires. So it is difficult to find the optimum design without a great number of iterations. Analytically only a few combinations are usually studied but it is very easy to take into account all the combinations using a CAD tool [1]. In this work the CAD tool used is PExprt (ANSYS [2]) which is being developed at UPMCEI.

Numerical and Experimental Studies of Sail Aerodynamics

The purpose of this investigation was the determination of the aerodynamic performance of sails and gain knowledge of the phenomena involved in order to improve the aerody¬namic characteristics. In this research, the airflow around different sails in four scenarios was studied. The method to analyze these scenarios was the combination of numerical simulations and experimental tests by taking advantage of the best of each tool. Two different Com¬putational Fluid Dynamic codes were utilized: the ANSYS-CFX and the CD-Adapco’s STAR-CCM+. The experimental tests were conducted in the Atmospheric Boundary Layer Wind Tunnel at the Universidad de Granada (Spain), the Twisted Flow Wind Tunnel at the University of Auckland (New Zealand) and the A9 Wind Tunnel at the Universidad Polit´ecnica de Madrid (Spain). Through this research, it was found the three-dimensional effect of the mast on the aerodynamic performance of an IMS Class boat. The pressure distribution on a Transpac 52 Class mainsail was also determined. Moreover, the aerodynamic perfor¬mance of the 43ft and 60ft Dhow Classes was obtained. Finally, a feasibility study was conducted to use a structural wing in combination with conventional propulsions systems. The main conclusion was that this research clarified gaps on the knowledge of the aerodynamic performance of sails. Moreover, since commercial codes were not specifically designed to study sails, a procedure was developed. On the other hand, innovative experimental techniques were used and applied to model-scale sails. The achievements of this thesis are promising and some of the results are already in use by the industry on a daily basis. El propósito de este estudio era determinar el comportamiento aerodinámico de unas velas y mejorar el conocimiento de los fenómenos que suceden para optimizar las características aerodinámicas de dichas velas. En esta investigación se estudió el flujo de aire alrededor de diferentes velas en cuatro escenarios. El método para analizar estos escenarios fue la combinación de simulaciones numéricas y ensayos experimentales mediante el aprovechamiento de las ventajas de cada herramienta. Se utilizaron dos códigos de dinámica de fluidos computacional: el ANSYS-CFX y el STAR-CCM+ de la empresa CD-Adapco. Los ensayos experimentales se desarrollaron en el túnel de viento de capa límite de la Universidad de Granada (España), el túnel de viento de la Universidad de Auckland (Nueva Zelanda) y en el túnel A9 de la Universidad Politécnica de Madrid (España). Mediante esta investigación, se determinó el efecto tridimensional del mástil en un velero de la clase IMS. También se describió la distribución de presiones sobre una mayor de un Transpac 52. Además, se obtuvo el comportamiento aerodinámico de las clases 43ft y 60ft de los veleros Dhows. Finalmente, se llevó a cabo un estudio de viabilidad de la utilización de un ala estructural en combinación con sistemas de propulsión convencionales. La conclusión principal de esta investigación fue la capacidad de explicar ciertas lagunas en el conocimiento del comportamiento aerodinámico de las velas en diferentes escenarios. Además, dado que los códigos comerciales no están específicamente diseñados para el estudio de velas, se desarrolló un procedimiento a tal efecto. Por otro lado, se han utilizado innovadoras técnicas experimentales y se han aplicado a modelos de velas a escala. Los logros de esta investigación son prometedores y algunos de los resultados obtenidos ya están siendo utilizados por la industria en su día a día.

Computational Methods for Identification of Vibrating Structures

System identification deals with the problem of building mathematical models of dynamical systems based on observed data from the system" [1]. In the context of civil engineering, the system refers to a large scale structure such as a building, bridge, or an offshore structure, and identification mostly involves the determination of modal parameters (the natural frequencies, damping ratios, and mode shapes). This paper presents some modal identification results obtained using a state-of-the-art time domain system identification method (data-driven stochastic subspace algorithms [2]) applied to the output-only data measured in a steel arch bridge. First, a three dimensional finite element model was developed for the numerical analysis of the structure using ANSYS. Modal analysis was carried out and modal parameters were extracted in the frequency range of interest, 0-10 Hz. The results obtained from the finite element modal analysis were used to determine the location of the sensors. After that, ambient vibration tests were conducted during April 23-24, 2009. The response of the structure was measured using eight accelerometers. Two stations of three sensors were formed (triaxial stations). These sensors were held stationary for reference during the test. The two remaining sensors were placed at the different measurement points along the bridge deck, in which only vertical and transversal measurements were conducted (biaxial stations). Point estimate and interval estimate have been carried out in the state space model using these ambient vibration measurements. In the case of parametric models (like state space), the dynamic behaviour of a system is described using mathematical models. Then, mathematical relationships can be established between modal parameters and estimated point parameters (thus, it is common to use experimental modal analysis as a synonym for system identification). Stable modal parameters are found using a stabilization diagram. Furthermore, this paper proposes a method for assessing the precision of estimates of the parameters of state-space models (confidence interval). This approach employs the nonparametric bootstrap procedure [3] and is applied to subspace parameter estimation algorithm. Using bootstrap results, a plot similar to a stabilization diagram is developed. These graphics differentiate system modes from spurious noise modes for a given order system. Additionally, using the modal assurance criterion, the experimental modes obtained have been compared with those evaluated from a finite element analysis. A quite good agreement between numerical and experimental results is observed.

Pulsatile flow in coronary bifurcations for different stenting techniques

The objective of this work is to analyze the local hem odynamic changes caused in a coronary bifurcation by three different stenting techniques: simple stenting of the main vessel, simple stenting of the main vessel with kissing balloon in the side branch and culotte. To carry out this study an idealized geometry of a coronary bifurcation is used, and two bifurcation angles, 45º and 90º, are chosen as representative of the wide variety of re al configurations. In order to quantify the influence of the stenting technique on the local blood flow, both numeri- cal simulations and experimental measurements are performed. First, steady simulations are carried out with the commercial code ANSYS-Fluent, and then, experimental measurements with PIV (Particle Image Velocimetry) obtained in the laboratory are used to validate the numerical simulation. The steady computational simulations show a good overall agreement with the experimental data. Second, pulsatile flow is considered to take into account the tran- sient effects. The time averaged wall shear stress, scillatory shear index and pressure drop obtained numerically are used to compare the behavior of the stenting techniques.