Three-port DC-DC Converter for Stand-Alone Photovoltaic Systems

System efficiency and cost effectiveness are of critical importance for photovoltaic (PV) systems. This paper addresses the two issues by developing a novel three-port DC-DC converter for stand-alone PV systems, based on an improved Flyback-Forward topology. It provides a compact single-unit solution with a combined feature of optimized maximum power point tracking (MPPT), high step-up ratio, galvanic isolation and multiple operating modes for domestic and aerospace applications. A theoretical analysis is conducted to analyze the operating modes followed by simulation and experimental work. The paper is focused on a comprehensive modulation strategy utilizing both PWM and phase-shifted control that satisfies the requirement of PV power systems to achieve MPPT and output voltage regulation. A 250 W converter was designed and prototyped to provide experimental verification in term of system integration and high conversion efficiency.

New modular structure DC-DC converter without electrolytic capacitors for renewable energy applications

The Vertical Distribution and Evolution of Slam Pressure on an Oscillating Wave Surge Converter

The accurate definition of the extreme wave loads which act on offshore structures represents a significant challenge for design engineers and even with decades of empirical data to base designs upon there are still failures attributed to wave loading. The environmental conditions which cause these loads are infrequent and highly non-linear which means that they are not well understood or simple to describe. If the structure is large enough to affect the incident wave significantly further non-linear effects can influence the loading. Moreover if the structure is floating and excited by the wave field then its responses, which are also likely to be highly non-linear, must be included in the analysis. This makes the description of the loading on such a structure difficult to determine and the design codes will often suggest employing various tools including small scale experiments, numerical and analytical methods, as well as empirical data if available.
Wave Energy Converters (WECs) are a new class of offshore structure which pose new design challenges, lacking the design codes and empirical data found in other industries. These machines are located in highly exposed and energetic sites, designed to be excited by the waves and will be expected to withstand extreme conditions over their 25 year design life. One such WEC is being developed by Aquamarine Power Ltd and is called Oyster. Oyster is a buoyant flap which is hinged close to the seabed, in water depths of 10 to 15m, piercing the water surface. The flap is driven back and forth by the action of the waves and this mechanical energy is then converted to electricity.
It has been identified in previous experiments that Oyster is not only subject to wave impacts but it occasionally slams into the water surface with high angular velocity. This slamming effect has been identified as an extreme load case and work is ongoing to describe it in terms of the pressure exerted on the outer skin and the transfer of this short duration impulsive load through various parts of the structure.
This paper describes a series of 40th scale experiments undertaken to investigate the pressure on the face of the flap during the slamming event. A vertical array of pressure sensors are used to measure the pressure exerted on the flap. Characteristics of the slam pressure such as the rise time, magnitude, spatial distribution and temporal evolution are revealed. Similarities are drawn between this slamming phenomenon and the classical water entry problems, such as ship hull slamming. With this similitude identified, common analytical tools are used to predict the slam pressure which is compared to that measured in the experiment.

Wave Interaction with an Oscillating Wave Surge Converter, Part 1: Viscous Effects

Bottom hinged oscillating wave surge converters are known to be an efficient method of extracting power from ocean waves. The present work deals with experimental and numerical studies of wave interactions with an oscillating wave surge converter. It focuses on two aspects: (1) viscous effects on device performance under normal operating conditions; and (2) effects of slamming on device survivability under extreme conditions. Part I deals with the viscous effects while the extreme sea conditions will be presented in Part II. The numerical simulations are performed using the commercial CFD package ANSYS FLUENT. The comparison between numerical results and experimental measurements shows excellent agreement in terms of capturing local features of the flow as well as the dynamics of the device. A series of simulations is conducted with various wave conditions, flap configurations and model scales to investigate the viscous and scaling effects on the device. It is found that the diffraction/radiation effects dominate the device motion and that the viscous effects are negligible for wide flaps.

The Characteristics of Wave Impacts on an Oscillating Wave Surge Converter

Wave impacts on an Oscillating Wave Surge Converter are examined using experimental and numerical methods. The mechanics of the impact event are identified experimentally with the use of images recorded with a high speed camera. It is shown that it is the device which impacts the wave rather than a breaking wave impacting the device. Numerical simulations using two different approaches are used to further understand the issue. Good agreement is shown between numerical simulations and experimental measurements at 25th scale.

Hydrodynamic Loading on a Bottom Hinged Oscillating Wave Surge Converter

This paper presents experimental and numerical studies into the hydrodynamic loading of a bottom-hinged large buoyant flap held rigidly upright in waves. Possible applications and limitations of physical experiments, a linear potential analytical method, a linear potential numerical method, a weakly non-linear tool and RANS CFD simulations are discussed. Different domains of applicability of these research techniques are highlighted considering the validity of underlying assumptions, complexity of application and feasibility in terms of resources like time and computing power needed to obtain results. Conclusions are drawn regarding the future extension of the numerical methods to the case of a moving flap.

Split Converter-Fed SRM Drive for Flexible Charging in EV/HEV Applications

Electric vehicles (EVs) and hybrid EVs are the way forward for green transportation and for establishing low-carbon economy. This paper presents a split converter-fed four-phase switched reluctance motor (SRM) drive to realize flexible integrated charging functions (dc and ac sources). The machine is featured with a central-tapped winding node, eight stator slots, and six rotor poles (8/6). In the driving mode, the developed topology has the same characteristics as the traditional asymmetric bridge topology but better fault tolerance. The proposed system supports battery energy balance and on-board dc and ac charging. When connecting with an ac power grid, the proposed topology has a merit of the multilevel converter; the charging current control can be achieved by the improved hysteresis control. The energy flow between the two batteries is balanced by the hysteresis control based on their state-of-charge conditions. Simulation results in MATLAB/Simulink and experiments on a 150-W prototype SRM validate the effectiveness of the proposed technologies, which may provide a solution to EV charging issues associated with significant infrastructure requirements.

Extreme Loads on an Oscillating Wave Surge Converter

A major difficulty in the design of full scale Wave Energy Converters is the need to design for two conflicting design criteria. In one instance devices must be designed to couple heavily to the incident wave force resulting in the efficient extraction of energy in small sea states, however devices must also be capable of withstanding the harsh conditions encountered during extreme seas. This paper presents an initial investigation of the extreme wave loading of a generic, surface-piercing, pitching flap-type device deployed in near shore wave conditions. Slamming of the flap is selected as the extreme load event for further investigation and the experimental methodologies employed are described. Preliminary results showing both local and global loading under such events are presented for the case of a flap tested in a 3-dimensional environment. Results are presented which show flap slamming effects on the pressures experienced on the front face of the flap.

Development and Validation of a Procedure for Numerical Vibration Analysis of an Oscillating Wave Surge Converter

During extreme sea states so called impact events can be observed on the wave energy converter Oyster. In small scale experimental tests these impact events cause high frequency signals in the measured load which decrease confidence in the data obtained. These loads depend on the structural dynamics of the model. Amplification of the loads can occur and is transferred through the structure from the point of impact to the load cell located in the foundation. Since the determination of design data and load cases for Wave Energy Converters originate from scale experiments, this lack of confidence has a direct effect on the development.

Numerical vibration analysis is a valuable tool in the research of the structural load response of Oyster to impact events, but must take into account the effect of the surrounding water. This can be done efficiently by adding an added mass distribution, computed with a linearised potential boundary element method. This paper presents the development and validation of a numerical procedure, which couples the OpenSource boundary element code NEMOH with the Finite Element Analysis tool CodeAster. Numerical results of the natural frequencies and mode shapes of the structure under the influence of added mass due to specific structural modes are compared with experimental results.

Wave Fields around Wave Energy Converter Arrays

Wave energy converters, by their nature, extract large amounts of energy
from incident waves. If the industry is to progress such that wave energy
becomes a significant provider of power in the future, large wave farms will
be required. Presently, consenting for these sites is a long and problematic
process, mainly due to a lack of knowledge of the potential environmental
impacts. Accurate numerical modelling of the effect of wave energy extraction
on the wave field and subsequent evaluation of changes to coastal
processes is therefore required. Modelling the wave field impact is also
necessary to allow optimum wave farm configurations to be determined.
This thesis addresses the need for more accurate representation of wave
energy converters in numerical models so that the effect on the wave field,
and subsequently the coastal processes, may be evaluated. Using a hybrid
of physical and numerical modelling (MIKE21 BW and SW models) the
effect of energy extraction and operation of a WEC array on the local wave
climate has been determined.
The main outcomes of the thesis are: an improved wave basin facility, in
terms of wave climate homogeneity, reducing the standard deviation of wave
amplitude by up to 50%; experimental measurement of the wave field around
WEC arrays, showing that radiated waves account for a significant proportion
of the wave disturbance; a new representation method of WECs for use
with standard numerical modelling tools, validated against experimental
results.
The methodology and procedures developed here allow subsequent evaluation
of changes to coastal processes and sediment transport due to WEC
arrays.

Investigating Tools used to Analyse the Impact of a Wave Farm on the surrounding Wave Field

For wave energy to become commercially viable, it is predicted that wave energy converters (WECs) will need to be installed in large wave farms. This will required an extensive environmental impact study. Assessments of impacts of these sites requires prior numerical modelling however the available tools have not been fully validated.
This project investigates the area surrounding an array of five scaled WEC models using experimental techniques. It then assesses the suitability of numerical tools to be validated with this experimental data. Validated numerical tools could then be used to predict parameters relating to the models such as reflection and transmission coefficients.
The physical aspect of this project was conducted in the Portaferry wave basin owned by Queen’s University Belfast. The device studied was a bottom hinged oscillating wave surge converter (OWSC) which penetrates the surface (similar to the Oyster device). The models were tested at 40th scale.

A Review of Numerical Modelling of Wave Energy Converter Arrays

Large-scale commercial exploitation of wave energy is certain to require the deployment of wave energy converters (WECs) in arrays, creating ‘WEC farms’. An understanding of the hydrodynamic interactions in such arrays is essential for determining optimum layouts of WECs, as well as calculating the area of ocean that the farms will require. It is equally important to consider the potential impact of wave farms on the local and distal wave climates and coastal processes; a poor understanding of the resulting environmental impact may hamper progress, as it would make planning consents more difficult to obtain. It is therefore clear that an understanding the interactions between WECs within a farm is vital for the continued development of the wave energy industry.To support WEC farm design, a range of different numerical models have been developed, with both wave phase-resolving and wave phase-averaging models now available. Phase-resolving methods are primarily based on potential flow models and include semi-analytical techniques, boundary element methods and methods involving the mild-slope equations. Phase-averaging methods are all based around spectral wave models, with supra-grid and sub-grid wave farm models available as alternative implementations.The aims, underlying principles, strengths, weaknesses and obtained results of the main numerical methods currently used for modelling wave energy converter arrays are described in this paper, using a common framework. This allows a qualitative comparative analysis of the different methods to be performed at the end of the paper. This includes consideration of the conditions under which the models may be applied, the output of the models and the relationship between array size and computational effort. Guidance for developers is also presented on the most suitable numerical method to use for given aspects of WEC farm design. For instance, certain models are more suitable for studying near-field effects, whilst others are preferable for investigating far-field effects of the WEC farms. Furthermore, the analysis presented in this paper identifies areas in which the numerical modelling of WEC arrays is relatively weak and thus highlights those in which future developments are required.

Offshore wind turbine simulation: multibody drive train. Bacl-to-back NPC (Neutral Point Clamped) converters: Fractional-order control

This paper is on offshore wind energy conversion systems installed on the deep water and equipped with back-to-back neutral point clamped full-power converter, permanent magnet synchronous generator with an AC link. The model for the drive train is a five-mass model which incorporates the dynamic of the structure and the tower in order to emulate the effect of the moving surface. A three-level converter and a four-level converter are the two options with a fractional-order control strategy considered to equip the conversion system. Simulation studies are carried out to assess the quality of the energy injected into the electric grid. Finally, conclusions are presented. (C) 2014 Elsevier Ltd. All rights reserved.

Study of AC losses in medium-sized high temperature superconducting coils

The study of AC losses in superconducting pancake coils is of utmost importance for the development of superconducting devices. Due to different technical difficulties this study is usually performed considering one of two approaches: considering superconducting coils of few turns and studying AC losses in a large frequency range vs. superconducting coils with a large number of turns but measuring AC losses only in low frequencies. In this work, a study of AC losses in 128 turn superconducting coils is performed, considering frequencies ranging from 50 Hz till 1152 Hz and currents ranging from zero till the critical current of the coils. Moreover, the study of AC losses considering two different simultaneous harmonic components is also performed and results are compared to the behaviour presented by the coils when operating in a single frequency regime. Different electrical methods are used to verify the total amount of AC losses in the coil and a simple calorimetric method is presented, in order to measure AC losses in a multi-harmonic context. Different analytical and numerical methods are implemented and/or used, to design the superconducting coils and to compute the total amount of AC losses in the superconducting system and a comparison is performed to verify the advantages and drawbacks of each method.

« Et ils prophétiseront » : la prophétie de Jl 3,1-5 reprise en Ac 2, 17-21 : clé d'interprétation du phénomène pentecostal

Cette présente recherche vise à défendre le point de vue selon lequel le don de l’Esprit dans le récit de la Pentecôte (Ac 2, 1-13) s’interprète principalement comme l’investissement d’une puissance habilitant au témoignage. À cette fin, nous posons l’hypothèse que le contenu d’Ac 2, 17-21 est un axe fondamental de la théologie pneumatique de l’œuvre lucanienne, lequel interprète la manifestation pentecostale dans une perspective prophétique. La démonstration se fait par le biais d’une analyse rédactionnelle d’Ac 2, 17-21, une citation de Jl 3,1-5 insérée dans un discours explicatif de Pierre du phénomène pentecostal. Nous examinons d’abord le lieu d’inscription de ce passage dans l’œuvre lucanienne afin d’évaluer la valeur stratégique de son emplacement (chapitre 1). Nous étudions ensuite l’interprétation que fait Luc de cette prophétie pour en venir à la conclusion qu’il envisage l’intervention de l’Esprit essentiellement dans une perspective d’habilitation à la prophétie (chapitre 2). Nous vérifions cette première conclusion dans l’Évangile de Luc (chapitre 3); puis ensuite dans les Actes des Apôtres (chapitre 4). Nous en arrivons ainsi à établir un parallélisme entre les étapes initiatiques du ministère de Jésus dans le troisième évangile et celui des disciples dans les Actes, pour y découvrir que, dans les deux cas, l’effusion de l’Esprit habilite à l’activité prophétique. Le ministère des disciples s’inscrit de la sorte dans le prolongement de celui du Maître. Nous soutenons, en fait, que tout le discours pneumatique de l’Évangile de Luc converge vers l’effusion initiale de l’Esprit sur les disciples dans le récit pentecostal, d’une part, et que cette effusion jette un éclairage sur l’ensemble de l’œuvre missionnaire des Actes, d’autre part. Bref, le passage explicatif du phénomène pentecostal, en l’occurrence Ac 2, 17-21, met en lumière un axe central des perspectives de Luc sur l’Esprit : Il s’agit de l’Esprit de prophétie. Dans cette optique, l’effusion de l’Esprit à la Pentecôte s’interpréterait essentiellement comme l’investissement du croyant d’une puissance en vue du témoignage.