Investigation on the Sr-doped ceria Ce1-xSrO2-delta (x=0.05-0.2) as an electrolyte for intermediate temperature SOFC

The effect of Sr doping in CeO2 for its use as solid electrolytes for intermediate temperature solid oxide fuel cells (IT-SOFCs) has been explored here. Ce1-xSrxO2-delta (x = 0.05-0.2) are successfully synthesized by citrate-complexation method. XRD, Raman, FT-IR, FE-SEM/EDX and electrochemical impedance spectra are used for structural and electrical characterizations. The formation of well crystalline cubic fluorite structured solid solution is observed for x = 0.05 based on XRD and Raman spectra. For compositions i.e., x > 0.05, however, a secondary phase of SrCeO3 is confirmed by the peak at 342 cm(-1) in Raman spectra. Although the oxygen ion conductivity was found to decrease with increase in x, based on ac-impedance studies, conductivity of Ce0.95Sr0.05O2-delta was found to be higher than of Ce0.95Gd0.1O2-delta and Ce0.8Gd0.2O2-delta. The decrease in conductivity of Ce1-xSrxO2-delta with increasing dopant concentration is ascribed to formation of impurity phase SrCeO3 as well as the formation of neutral associated pairs, Se `' Ce V-o. The activation energies are found to be 0.77, 0.83, 0.85 and 0.90 eV for x = 0.05, 0.1, 0.15 and 0.20, respectively. (C) 2014 Elsevier B.V. All rights reserved.

Optimal Trajectory Generation for Convergence to a Rectilinear Path

This paper presents a strategy to determine the shortest path of a fixed-wing Miniature Air Vehicle (MAV), constrained by a bounded turning rate, to eventually fly along a given straight line, starting from an arbitrary but known initial position and orientation. Unlike the work available in the literature that solves the problem using the Pontryagin's Minimum Principle (PMP) the trajectory generation algorithm presented here considers a geometrical approach which is intuitive and easy to understand. This also computes the explicit solution for the length of the optimal path as a function of the initial configuration. Further, using a 6-DOF model of a MAV the generated optimal path is tracked by an autopilot consisting of proportional-integral-derivative (PID) controllers. The simulation results show the path generation and tracking for different cases.

Efficient Adaptive Mesh Refinement for MoM-based Package-Board 3D Full-wave Extraction

The accurate solution of 3D full-wave Method of Moments (MoM) on an arbitrary mesh of a package-board structure does not guarantee accuracy, since the discretizations may not be fine enough to capture rapid spatial changes in the solution variable. At the same time, uniform over-meshing on the entire structure generates large number of solution variables and therefore requires an unnecessarily large matrix solution. In this work, a suitable refinement criterion for MoM based electromagnetic package-board extraction is proposed and the advantages of the adaptive strategy are demonstrated from both accuracy and speed perspectives.

Structural, thermal and quantum chemical studies of p-coumaric and caffeic acids

Two hydroxycinnamic acids viz., p-coumaric, and caffeic acids have been extracted and purified from Parthenium hysterophorus, subsequently characterized by elemental analysis, FT-IR, NMR, single crystal X-ray crystallography. The optimized structures of these acids were calculated in terms of density functional theory by Gaussian 09. The validation of experimental and theoretically obtained data for structural parameters such as bond lengths and bond angles has have been carried out to analyze the statistical significance by curve fitting analysis and the values of correlation coefficient found to be 0.985, 0.992, and 0.984, 0.975 in p-coumaric, and caffeic acids, respectively. The calculated HOMO and LUMO energies show the eventual charge transfer interaction within the molecule. Thermal studies were also carried out by thermogravimetry (TG), differential thermogravimetric analysis (DTA), and derivative thermogravimetry (DTG). (C) 2014 Elsevier B.V. All rights reserved.

Lateralisation abnormalities in obsessive-compulsive disorder: a line bisection study

Objective Asymmetry in brain structure and function is implicated in the pathogenesis of psychiatric disorders. Although right hemisphere abnormality has been documented in obsessive-compulsive disorder (OCD), cerebral asymmetry is rarely examined. Therefore, in this study, we examined anomalous cerebral asymmetry in OCD patients using the line bisection task. Methods A total of 30 patients with OCD and 30 matched healthy controls were examined using a reliable and valid two-hand line bisection (LBS) task. The comparative profiles of LBS scores were analysed using analysis of covariance. Results Patients with OCD bisected significantly less number of lines to the left and had significant rightward deviation than controls, indicating right hemisphere dysfunction. The correlations observed in this study suggest that those with impaired laterality had more severe illness at baseline. Conclusions The findings of this study indicate abnormal cerebral lateralisation and right hemisphere dysfunction in OCD patients.

Nonlinear control of an air-breathing engine including its validation with vehicle guidance

An implementable nonlinear control design approach is presented for a supersonic air-breathing ramjet engine. The primary objective is to ensure that the thrust generated by the engine tracks the commanded thrust without violating the operational constraints. An important constraint is to manage the shock wave location in the intake so that it neither gets detached nor gets too much inside the intake. Both the objectives are achieved by regulating the fuel flow to the combustion chamber and by varying the throat area of the nozzle simultaneously. The design approach accounts for the nonlinear cross-coupling effects and nullifies those. Also, an extended Kalman filter has been used to filter out the sensor and process noises as well as to make the states available for feedback. Furthermore, independent control design has been carried out for the actuators. To test the performance of the engine for a realistic flight trajectory, a representative trajectory is generated through a trajectory optimization process, which is augmented with a newly-developed finite-time state dependent Riccati equation technique for nullifying the perturbations online. Satisfactory overall performance has been obtained during both climb and cruise phases. (C) 2015 Elsevier Masson SAS. All rights reserved.

Evolution of high-pressure mafic granulites and pelitic gneisses from NE Madagascar: Tectonic implications

The occurrence of high-pressure mafic-ultramafic bodies within major shear zones is one of the indicators of paleo-subduction. In mafic granulites of the Andriamena complex (north-eastern Madagascar) we document unusual textures including garnet-clinopyroxene-quartz coronas that formed after the breakdown of orthopyroxene-plagioclase-ilmenite. Textural evidence and isochemical phase diagram calculations in the Na2O-CaO-K2O-FeO-MgO-Al2O3-SiO2-H2O-TiO2 system indicate a pressure-temperature (P-T) evolution from an isothermal (780 degrees C) pressure up to c. 24 kbar to decompression and cooling. Such a P-T trajectory is typically attained in a subduction zone setting where a gabbroic/ultramafic complex is subducted and later exhumed to the present crustal level during oceanic closure and final continental collision. The present results suggest that the presence of such deeply subducted rocks of the Andriamena complex is related to formation of the Betsimisaraka suture. LA-ICPMS U-Pb zircon dating of pelitic gneisses from the Betsimisaraka suture yields low Th/U ratios and protolith ages ranging from 2535 to 2625 Ma. A granitic gneiss from the Alaotra complex yields a zircon crystallization age of ca. 818 Ma and Th/U ratios vary from 1.08 to 2.09. K-Ar dating of muscovite and biotite from biotite-kyanite-sillimanite gneiss and garnet-biotite gneiss yields age of 486 +/- 9 Ma and 459 +/- 9 Ma respectively. We have estimated regional crustal thicknesses in NE Madagascar using a flexural inversion technique, which indicates the presence of an anomalously thick crust (c. 43 km) beneath the Antananarivo block. This result is consistent with the present concept that subduction beneath the Antananarivo block resulted in a more competent and thicker crust. The textural data, thermodynamic model, and geophysical evidence together provide a new insight to the subduction history, crustal thickening and evolution of the high-pressure Andriamena complex and its link to the terminal formation of the Betsimisaraka suture in north-eastern Madagascar. (C) 2015 Elsevier B.V. All rights reserved.

Strength reliability and in vitro degradation of three-dimensional powder printed strontium-substituted magnesium phosphate scaffolds

Strontium ions (Sr2+) are known to prevent osteoporosis and also encourage bone formation. Such twin requirements have motivated researchers to develop Sr-substituted biomaterials for orthopaedic applications. The present study demonstrates a new concept of developing Sr-substituted Mg-3(PO4)(2) - based biodegradable scaffolds. In particular, this work reports the fabrication, mechanical properties with an emphasis on strength reliability as well as in vitro degradation of highly biodegradable strontium-incorporated magnesium phosphate cements. These implantable scaffolds were fabricated using three-dimensional powder printing, followed by high temperature sintering and/or chemical conversion, a technique adaptable to develop patient-specific implants. A moderate combination of strength properties of 36.7 MPa (compression), 242 MPa (bending) and 10.7 MPa (tension) were measured. A reasonably modest Weibull modulus of up to 8.8 was recorded after uniaxial compression or diametral tensile tests on 3D printed scaffolds. A comparison among scaffolds with varying compositions or among sintered or chemically hardened scaffolds reveals that the strength reliability is not compromised in Sr-substituted scaffolds compared to baseline Mg-3(PO4)(2). The micro-computed tomography analysis reveals the presence of highly interconnected porous architecture in three-dimension with lognormal pore size distribution having median in the range of 17.74-26.29 mu m for the investigated scaffolds. The results of extensive in vitro ion release study revealed passive degradation with a reduced Mg2+ release and slow but sustained release of Sr2+ from strontium-substituted magnesium phosphate scaffolds. Taken together, the present study unequivocally illustrates that the newly designed Sr-substituted magnesium phosphate scaffolds with good strength reliability could be used for biomedical applications requiring consistent Sr2+-release, while the scaffold degrades in physiological medium. Statement of significance The study investigates the additive manufacturing of scaffolds based on different strontium-substituted magnesium phosphate bone cements by means of three-dimensional powder printing technique (3DPP). Magnesium phosphates were chosen due to their higher biodegradability compared to calcium phosphates, which is due to both a higher solubility as well as the absence of phase changes (to low soluble hydroxyapatite) in vivo. Since strontium ions are known to promote bone formation by stimulating osteoblast growth, we aimed to establish such a highly degradable magnesium phosphate ceramic with an enhanced bioactivity for new bone ingrowth. After post-processing, mechanical strengths of up to 36.7 MPa (compression), 24.2 MPa (bending) and 10.7 MPa (tension) could be achieved. Simultaneously, the failure reliability of those bioceramic implant materials, measured by Weibull modulus calculations, were in the range of 4.3-8.8. Passive dissolution studies in vitro proved an ion release of Mg2+ and PO43- as well as Sr2+, which is fundamental for in vivo degradation and a bone growth promoting effect. In our opinion, this work broadens the range of bioceramic bone replacement materials suitable for additive manufacturing processing. The high biodegradability of MPC ceramics together with the anticipated promoting effect on osseointegration opens up the way for a patient-specific treatment with the prospect of a fast and complete healing of bone fractures. (C) 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Small-Signal Stability Analysis of an Open-Loop Induction Motor Drive Including the Effect of Inverter Deadtime

This paper demonstrates light-load instability in a 100-kW open-loop induction motor drive on account of inverter deadtime. An improved small-signal model of an inverter-fed induction motor is proposed. This improved model is derived by linearizing the nonlinear dynamic equations of the motor, which include the inverter deadtime effect. Stability analysis is carried out on the 100-kW415-V three-phase induction motor considering no load. The analysis brings out the region of instability of this motor drive on the voltage versus frequency (V-f) plane. This region of light-load instability is found to expand with increase in inverter deadtime. Subharmonic oscillations of significant amplitude are observed in the steady-state simulated and measured current waveforms, at numerous operating points in the unstable region predicted, confirming the validity of the stability analysis. Furthermore, simulation and experimental results demonstrate that the proposed model is more accurate than an existing small-signal model in predicting the region of instability.

Determinación de la incidencia de parásitos internos en los bovinos del Complejo uno y dos de la Empresa Genética Agenor Gómez, Boaco, Nicaragua

El presente trabajo se realizó en el periodo comprendido entre Noviembre y Diciembre de 1989, con el objetivo de investigar la infestación de parásitos gastrointestinales y pulmonares de mayor importancia económica en los bovinos del complejo 1 y 2 de la empresa genética Agenor Gómez. Boaco, Nicaragua. Se muestrearon 242 animales, entre bovinos de la raza Aberdeen Angus y Brahman, distribuidos en las categorías siguientes: C1 (0-1 año), C2 (1-3 años) y C3 (>3 años). Las muestras fueron extraídas directamente del recto animal, luego refrigeradas a 5°C y fueron analizadas en laboratorio de parasitología del MIDINRA, localizado en municipio de Camoapa V región. La cantidad de huevos y larvas se registró para cada género empleando las técnicas de sedimentación en agua, flotación con solución salina saturada y el método de larvoscopia e identificación con fotografías. Al realizar el ANDEVA por género de parásitos reportados en el análisis coprológico para la variable N° de huevos y larvas/gr de heces, se encontró que existen diferencias significativas con P>0.05 entre los promedios observados de los diferentes hatos. Los niveles de infestación promedio en los distintos hatos oscilaron entre 0u y 2lu; donde u= número de huevos y larvas/gramos de heces. De estos 48 promedios (8 hatos por 6 géneros de parásitos), 6 alcanzaron valores >9; 1 hato C1 de la upe Las Brisas con media de 2lu del género Haemonchus, 1 hato e de la upe San Miguel con media de 20.87u del género Strongyloides, 1 hato C2 de la upe San Jorge con media de 17.69u del género Strongyloides, 2 hatos C1 de las upe las Brisas y San Miguel con medias de 10.67u y medias de 10.5u respectivamente, ambos del género Coccidia y 1 hato e2 de la upe San Jorge con media de 9.6lu del género Coccidia. En los promedios restantes se obtuvieron valores <6u perteneciendo a la calificación leve. Posteriormente se realizó un análisis de correlación para determinar el grado de asociación existente entre cada uno de los géneros de parásitos económicamente importantes, encontrándose que el género Coccidia presentó el mayor grado de correlación con respecto a los demás géneros encontrados, se encontró que las correlaciones >= 0.25 corresponden a los géneros Coccidia, Moniezia, Neoascaris, Strongyloides y Haemonchus con r de 0.25, 0.25, 0.48, 0.30 respectivamente, similar para Haemonchus y Moniezia con r de 0.289.

Circovirus Porcino (PCV2) en la granja porcina San José Aganorsa durante el periodo del 2011 al 2013

En el presente trabajo se evaluó la importancia sanitaria y económica que presenta la enfermedad Circovirus en la producción porcina de animales de 1 día de nacidos hasta las 12 semanas de vida, mediante tres evaluaciones en la granja porcina San José, AGANORSA en el municipio de Mateare, la prueba diagnóstica utilizada fue ELISA con captura de anticuerpo especifico para circovirus porcino tipo 2 (PCV2), realizada en el laboratorio nacional de diagnóstico veterinario MAGFOR en julio del 2011. En la primera evaluación se determinaron los indicadores epidemiológicos prevalencia, mortalidad y virulencia; utilizando datos de la empresa (diciembre 2011- julio 2012). Se registraron 15 lotes de animales vacunados y 15 no vacunados. Las variables evaluadas fueron: animales eliminados, animales muertos y total de enfermos. Mediante la prueba de comparación de medias (Duncan) se encontraron diferencias significativas (0.05>P) para las variables, prevalencia con el 19% en lotes no vacunados y 15% en lotes vacunados; para mortalidad el 14% y 9% en los lotes respectivos. La virulencia en lotes no vacunados y vacunados mostró diferencia significativa (0.05>P por Tukey), obteniendo valores del 76.82% y 63.82% para lotes no vacunados y vacunados, respectivamente. Mediante la estimación del coeficiente de correlación (Pearson), se encontró la existencia de relación entre el tratamiento y las variables prevalencia, mortalidad y virulencia. Las pérdidas económicas estimadas en los lotes sin vacunar fueron del 18.47% y en los vacunados del 14.90%, equivalentes a 5,893.545 y 5,544.840 Córdobas, respectivamente; con la vacunación se logró una reducción de un 3.57% de pérdidas económicas, que equivalen a 348,705.00 Córdobas. En la segunda y tercera evaluación las pérdidas económicas fueron del 4.47% y del 6%, lo que se traduce en 184,404.00 y 303,105.00 Córdobas, respectivamente. Para evaluar la efectividad de la aplicación de la vacuna sobre la mortalidad, se utilizó una prueba t-Student, con resultado estadístico altamente significativo (0.001>P). En la primera evaluación se encontraron resultados positivos frente a la vacunación, reduciendo en gran medida los indicadores epidemiológicos; en la segunda y tercera evaluación se determinaron porcentajes altos de mortalidad debido a factores de manejo y otros agentes etiológicos presentes en la granja (Staphylococcus sp. y Haemophilus Parasuis). La implementación de la vacuna para el control y prevención de Circovirus porcino PCV2, fue todo un éxito en la granja, mejorando los pesos obtenidos a las 23 semanas de vida, de 205 a 242 libras, reduciendo el porcentaje de animales pequeños (colitas) y la mortalidad causada por PCV2.

Diversidad florística del bosque de galería en dos localidades del departamento de Carazo, Nicaragua

En las localidades Los Encuentros y Chacocente, en el departamento de Carazo, se realizó un estudio sobre la composición florísticas de las especies arbóreas en el bosque de galería. Los resultados corresponden a un inventario completo de los árboles de 1 O cm de diámetro a la altura del pecho (Dap) y regeneración natural en parcelas con área neta de muestreo de 1 hectárea en cada sitio, con sub-parcelas de 100 m2 para el muestreo de regeneración. Los bosques estudiados son Chacocente (360 msnm) y Los Encuentros (180 msnm). Ambos bosques son de galería y pertenecen a la zona de Vida Bosque Tropical Seco con transición a subtropical. , según el sistema de clasificación de Holdridge. En ambos bosques se encontraron un total 65 especies, pertenecientes a 39 familias y 53 géneros. En el bosque localizado en Los Encuentros, se encontraron 24 especies, siendo las mas frecuentes el Papaturro (Coccoloba caracasana), anona (Annona glabra) y Chaperno blanco (Lonchocarpus minimiflorus). En Chacocente se encontraron 41 especies, siendo las mas frecuentes Palo de piojo (Trichilia hirta), Naranjillo (Capparis odoratisima) y Melero (Thoudinium decandrum). La abundancia de árboles con Dap mayor de 10 cm fue de 333 en Chacocente y 379 en Los Encuentros. Los cocientes de mezcla obtenidos fueron 1:8 para el bosque del Refugio de Vida Silvestre, Chacocente y 1:15 para el de los Encuentros. En ambas comunidades difieren las familias mayormente representadas. Los valores de los coeficientes de Jaccard (4.4 %) y Sorensen (8.4 %) revelan poca similitud florística entre ambos sitios. La regeneración natural presentó en algunos aspectos el mismo comportamiento de la vegetación con Dap mayor o igual a los 10 cm, siendo la única diferencia los valores del coeficiente de mezcla que presentan al bosque de la comunidad Los Encuentros con mayor diversidad florística (l :50 en comparación con 1:16 de Chacocente). La abundancia de individuos de la regeneración natural fue de 242 individuos por hectárea en Los Encuentros y de 860 individuos por hectarea en Chacocente.

Determinación de la acción residual en diferentes dosis de chlorpyrifos (Lorsban) con énfasis en la dosis mínima, para control de cogollero (Spodoptera frugiperda J.E. Smith; Lepidotera: Noctuidae) en maíz

Este ensayo fue realizado con el objetivo de conocer cuál es el efecto de diferente dosis de chlorpyripos sobre el tiempo de protección, buscando la dosis más adecuada para control del gusano cogollero, spodoptera frugiperda (j.e Smith) , en maíz. De manera que este estudio nos permitiera decidir cuál es el momento indicado de un recuento para una posterior aplicación del pesticida y 6 fundamentalmente bajar los costos de protección. Al evaluar la acción residual se encontró diferencia significativa entre las dosis de 1,0.5, 0.25, 0.125,0.0625 1t/mz de chlorpyrifos. La dosis de 0.25 1t/mz no es diferente de la dosis de 1 1t/mz cuanto a la acción residual de chlorpyrifos y sus promedio de rendimiento tienen también mucha similiridad pero su costo determinan la diferencia. Los resultado conducen a decidir la recomendación de la dosis de 0.25 1t/mz por ser la más económica con una acción residual de 23.3 días y un costo de control de $ 242.55 con 2.2 aplicaciones promedio en todo el periodo del cultivo, a diferencia de la dosis más alta usada de 1 1t/mz con una acción residual de 21.9 días, un promedio de 2.6 aplicaciones y un costo de $ 795.6 y el rendimiento final no es diferente entre ellas. Por otro lado de asegura que con una sola aplicación de chlorpyrifos se garantiza la mortalidad de larvas de spodoptera frugiperda (j.e. Smith) durante a los 5 a 10 días después de aplicación. Todo los anteriores permite dar un lapso estable en el tiempo que se sabe tomar para recuento, decidir la dosis mínima más económica, por su acción residual y bajar así los costó de producción.

新材料与材料制备新工艺研讨会选辑前言

新材料与材料制备新工艺研讨会选辑前言洪友士中国科学院力学研究所，北京１０００８０１９９４年８月，中科院力学所在青岛举办了“新材料与材料制备新工艺高级研讨班”。有４０多位研究人员参加了此次学术研讨，其中有７位特邀代表，他们是：中科院固体物理所葛庭燧院士...