Construction and application of a portable microcontrolled turbidimeter for the in situ determination of sulfate

This study reports on the construction of a turbidimeter employing light emitting diodes as radiation source at a wavelength of 405 nm, a photodiode as detector, a temperature sensor and a microcontroller used for data acquisition and processing. The turbidimeter was applied to determine sulfate concentrations in natural water employing barium chloride as reagent. Potential interferences and recovery studies were performed and an interference of 3.5 % and a recovery between 97.8 and 108 % were estimated. The analytical performance of in situ turbidimeter for the determination of sulfate was evaluated and compared with two commercial spectrophotometers and a good agreement was obtained.

Energiansäästö kotitalouksien valaistuksessa Suomessa

Tässä työssä arvioidaan kotitalouksien energiansäästöpotentiaalia valaistuksen osalta Suomessa. Euroopan Unioni on ratifioinut päästövähennystavoitteen 20 % koskien kaikkia primäärienergiantuotantomuotoja. Päästövähennystavoite on tarkoitus toteuttaa vuoteen 2020 mennessä. Tässä kandidaatintyössä arvioidaan saavutettavissa olevaa energiansäästöpotentiaalia Suomessa kotitalouksissa laitesähkön osalta. Energiansäästöpotentiaalin arviointi perustuu hehkulampun korvaamismahdollisuuksien vertailuun. Valaistuksessa voidaan saavuttaa jopa 75 % sähkönsäästö, kun korvataan yksi 60 W hehkulamppu vastaavan valomäärän tuottavalla energiansäästölampulla. Kokonaisuudessa kotitalouksien valaistuksessa on tehostamispotentiaalia noin 60 %. Valaistuksen tehostamisella saavutetaan noin 1,5 TWh säästö Suomen kokonaissähkökulutuksessa. Saavutettavat säästöt voivat olla jopa suuremmatkin, jos käytetään lisäksi älykästä valonohjausta. Johtopäätöksenä voidaan todeta, että tehostamispotentiaalia on merkittävästi ja tehostaminen on yksittäiselle kotitaloudelle taloudellisesti kannattavaa. Energiansäästöpotentiaalin toteuttamisen vaikutuksia kansantalouteen ei ole arvioitu.

Unusual bismuth-containing surface layers of III-V compound semiconductors

The understanding and engineering of bismuth (Bi) containing semiconductor surfaces are signi cant in the development of novel semiconductor materials for electronic and optoelectronic devices such as high-e ciency solar cells, lasers and light emitting diodes. For example, a Bi surface layer can be used as a surfactant which oats on a III-V compound-semiconductor surface during the epitaxial growth of IIIV lms. This Bi surfactant layer improves the lm-growth conditions if compared to the growth without the Bi layer. Therefore, detailed knowledge of the properties of the Bi/III-V surfaces is needed. In this thesis, well-de ned surface layers containing Bi have been produced on various III-V semiconductor substrates. The properties of these Bi-induced surfaces have been measured by low-energy electron di raction (LEED), scanning-tunneling microscopy and spectroscopy (STM), and synchrotron-radiation photoelectron spectroscopy. The experimental results have been compared with theoretically calculated results to resolve the atomic structures of the studied surfaces. The main ndings of this research concern the determination of the properties of an unusual Bi-containing (2×1) surface structure, the discovery and characterization of a uniform pattern of Bi nanolines, and the optimization of the preparation conditions for this Bi-nanoline pattern.

Veden desinfiointi UV-LED-valolla

Veden riittämätön puhdistus aiheuttaa riskin veden käyttäjille. Miljoonia kuolemia vuosittain aiheuttavien vesiteitse leviävien sairauksien ehkäisemiseksi vaaditaan tehokkaita juomaveden desinfiointimenetelmiä. Kuivuuden ja väestönkasvun myötä veden tarve on lisääntynyt ja vedenkulutus tulee yhä kasvamaan. Tästä syystä mahdollisuus kierrättää vettä hyödyntäen sitä esimerkiksi kasteluun on saanut yhä enemmän huomiota. Kierrätettävä vesi on kuitenkin käsiteltävä huolellisesti sen sisältämän mikrobiologisen kontaminaatioriskin vuoksi. Ultraviolettisäteily luokitellaan fysikaaliseksi desinfiointimenetelmäksi. Sen tehokkuus perustuu mikro-organismien absorboimaan UV-säteilyyn, jonka aiheuttamien DNA:ssa tai RNA:ssa tapahtuvien muutoksien seurauksena mikro-organismi inaktivoituu ja estyy lisääntymästä. UV-desinfioinnissa on tyypillisesti käytetty elohopeahöyrylamppuja. Vaihtoehtoinen UV-säteilyn lähde ovat LEDit eli valoa emittoivat diodit. Matalapaine-elohopeahöyrylamppujen emittoima säteily on aallonpituudella 254 nm ja keskipaine-elohopeahöyrylamppujen emittoima säteily on laajakaistaista säteilyä. Energiatehokkuuden lisäksi LEDien etuna on, että niillä voidaan tuottaa kapeakaista säteilyä aallonpituudella, joka parhaiten absorboituu DNA:han. Tämän diplomityön tarkoituksena oli tutkia, onko UVC-alueen aallonpituuksien yhdistelmillä synergistisiä etuja LEDien desinfiointitehokkuuteen, kun desinfioidaan virtaavaa vettä useilla säteilyannoksilla ja indikaattorimikrobina käytetään kolibakteeria. Tavoitteena oli myös tutkia tällä hetkellä saatavissa olevien LEDien desinfiointitehokkuutta energiatehokkuuden näkökulmasta. Yksittäisistä aallonpituuksista desinfiointitehokkuudeltaan parhaimmaksi osoittautui 260 nm, aallonpituuksien yhdistelmistä tehokkain oli 265 nm:n ja 260 nm:n yhdistelmä. Muilla aallonpituuksien yhdistelmillä ei saavutettu odotettua parempaa desinfiointitehokkuutta. Optiselta teholtaan parhaimmat LEDit, 265 nm, 270 nm ja 275 nm olivat kokeiden perusteella myös energiatehokkuuden kannalta tarkasteltuina parhaimmat sekä yksittäin että yhdistelminä. UVC-aallonpituuksia emittoivien LEDien optisen tehokkuuden paraneminen on edellytys LEDien hyödyntämiselle desinfioinnissa.

Synthèse de nouveaux matériaux conducteurs comportant des unités aromatiques conjuguées et analyse de leurs propriétés physico-chimiques

Les matériaux conjugués ont fait l’objet de beaucoup de recherches durant les dernières années. Les nouveaux matériaux présentent des propriétés intéressantes que ce soit au niveau optique, électrique, mécanique ou même les trois en même temps. La synthèse reste la difficulté principale dans la fabrication de dispositifs électroniques. Les méthodes utilisées pour y parvenir sont l’électropolymérisation, le couplage de Suzuki ou de Wittig. Ces techniques comportent encore de nombreuses contraintes et s’avèrent difficilement réalisables à grande échelle. Les thiophènes, les pyrroles et les furanes ont démontré une bonne conductibilité et une bande de conduction basse due à une conjugaison accrue. L’objectif ici est de synthétiser des oligomères principalement composés de thiophènes dans le but d’en caractériser les propriétés spectroscopiques, électrochimiques et de conduction. La synthèse est souvent l’étape délicate de la fabrication de matériaux conjugués. Nous présentons ici une méthode de synthèse simple par modules avec des unités hétérocycliques. Les modules complémentaires sont attachés par condensation entre un aldéhyde et une amine menant à la formation d’un lien robuste, l’azomethine. Les résultats des propriétés photophysiques et électrochimiques de ces matériaux conjugués seront présentés. En ayant recours à différents groupes électrodonneurs et électroaccepteurs, en variant le degré de conjugaison ou en utilisant différents hétérocycles, les propriétés spectroscopiques, électrochimiques et de bande de conduction peuvent être adaptées à volonté, ce qui en fait des matériaux aux propriétés modelables. Ces nouvelles molécules seront analysées pour en déceler les propriétés recherchées dans la fabrication d’OLED. Nous explorerons les domaines de l’oxidation electrochimique réversible et de la polymérisation menant à la fabrication de quelques prototypes simples.

Développement de composés conjugués en étoile de première génération incluant des liens azométhines et études électrochimiques et photophysiques

Les matériaux conjugués sont de nos jours très utilisés dans de nombreuses applications ainsi qu’en recherche. L’enchainement des liaisons π-σ-π permet la délocalisation des électrons et d’obtenir différentes propriétés comme la conduction, la fluorescence, la chélation, etc. Ainsi, de nombreux dispositifs utilisent ces caractéristiques en vue d’obtenir de nouveaux matériaux révolutionnaires comme les cellules solaires, les transistors à effet de champs, les dispositifs électrochromiques, etc.. Les dispositifs électrochromiques font partie des dispositifs en vogue. Ils sont capables de changer de couleur selon le potentiel électrique appliqué. Ils se distinguent par la simplicité du mode de conception et ils ne nécessitent pas de fonctionner dans des conditions drastiques comme une atmosphère contrôlée. Ces dispositifs sont actuellement utilisés et commercialisés comme fenêtre intelligente, camouflage, papier électronique et carte de visite personnalisée pour n’en nommer que quelques-uns. Deux propriétés sont essentielles pour que des composés puissent être utilisés dans ces familles de dispositifs : la réversibilité à l’oxydation et la stabilité à l’air et à la lumière. Dans le groupe de recherche du professeur W.G. Skene, l’axe principal de recherche est basé sur la conception de nouveaux matériaux conducteurs comportant des liaisons azométhines. Les principaux matériaux étudiés sont des dérivés de thiophènes et de fluorènes. De précédents résultats ont montré que plusieurs produits issus de la réaction de condensation entre les dérivés du 2,5-diaminothiophène et de thiophènes diformylés menaient à des produits possédant d’excellentes propriétés photophysiques et électrochimiques. C’est en partant de ces résultats encourageants qu’il a été choisi de synthétiser une nouvelle famille de produits avec un nouveau substrat fonctionnalisé. Ce dernier possède d’excellentes propriétés électrochimiques et photophysiques : la triphénylamine. Deux familles de produits ont été synthétisées qui possèdent toutes comme cœur une triphénylamine. Cette dernière a été modifiée de façon à créer une, deux ou trois liaisons azométhines avec différents thiophènes. Deux dérivés du thiophène ont été choisis afin d’étudier l’influence des groupements donneurs et accepteurs sur ces nouveaux types de composés encore jamais étudiés. Les résultats des différentes synthèses et analyses ont été effectués par RMN, spectrométrie de masse, spectrométrie d’absorbance UV-Visible, fluorescence et voltampérométrie cyclique sont rapportées dans le présent recueil.

Effet de la microstructure sur les propriétés excitoniques des polymères semi-conducteurs semi-cristallins

Les polymères semi-conducteurs semicristallins sont utilisés au sein de diodes électroluminescentes, transistors ou dispositifs photovoltaïques organiques. Ces matériaux peuvent être traités à partir de solutions ou directement à partir de leur état solide et forment des agrégats moléculaires dont la morphologie dicte en grande partie leurs propriétés optoélectroniques. Le poly(3-hexylthiophène) est un des polymères semi-conducteurs les plus étudiés. Lorsque le poids moléculaire (Mw) des chaînes est inférieur à 50 kg/mol, la microstructure est polycristalline et composée de chaînes formant des empilements-π. Lorsque Mw>50 kg/mol, la morphologie est semicristalline et composée de domaines cristallins imbriquées dans une matrice de chaînes amorphes. À partir de techniques de spectroscopie en continu et ultrarapide et appuyé de modèles théoriques, nous démontrons que la cohérence spatiale des excitons dans ce matériau est légèrement anisotrope et dépend de Mw. Ceci nous permet d’approfondir la compréhension de la relation intime entre le couplage inter et intramoléculaire sur la forme spectrale en absorption et photoluminescence. De plus, nous démontrons que les excitations photogénérées directement aux interfaces entre les domaines cristallins et les régions amorphes génèrent des paires de polarons liés qui se recombinent par effet tunnel sur des échelles de temps supérieures à 10ns. Le taux de photoluminescence à long temps de vie provenant de ces paires de charges dépend aussi de Mw et varie entre ∼10% et ∼40% pour les faibles et hauts poids moléculaires respectivement. Nous fournissons un modèle permettant d’expliquer le processus de photogénération des paires de polarons et nous élucidons le rôle de la microstructure sur la dynamique de séparation et recombinaison de ces espèces.

Synthèse et étude de nouvelles molécules potentiellement polymérisables pour la fabrication de matériaux électroluminescents : analogues du 1,3,5 benzènetripyrrole, méthyle 3,5-bipyrrolebenzoate et 6,12-diméthyle-1,5-dipyrrolediazocane

Pyrroles are found in various natural products and in the chemical composition of certain drugs because of their interesting biological properties. Lipitor, Tolmetin and Amtolmetin are examples of drugs with 1,2,5-substituted pyrroles in their composition, in which biological activities have been certified. Moreover, pyrroles are used as precursors of semiconductor polymers, oligomers and dendrimers useful for the synthesis of electroluminescent materials used in devices, such as organic light-emitting diodes, field-effect transistors, solar and organic photovoltaic cells. We are interested in conjugated polymers based on pyrrole due to their optical properties, electrochemical and the conductivity produced by electron delocalization along their carbon chains. The overall objective of the work presented in this thesis is the synthesis of new molecules based on pyrrole for studying their electronic and electrochemical properties as well for the synthesis of conjugated polymers. Initially, we performed the synthesis of 1,3,5-tri-(1-alkyl-5-methylpyrrol-2-yl)benzenes, which may serve as precursors for the synthesis of conjugated dendrimers. Their synthesis was made in three steps starting from trimethyl 1,3,5-benzene-tricarboxylate which was converted to 1,3,5-tri-(pent-4-enoyl)benzene using vinylmagnesium bromide in a Grignard reaction catalyzed by copper cyanide. The olefins of 1,3,5-tri-(pent-4-enoyl)benzene were oxidized to produce 1,3,5-tri-(4-oxopentanoyl)benzene using a modified protocol of the Tsuji-Wacker reaction. Subsequent, Paal-Knorr condensation reactions on 1,3,5-tri-(4-oxopentanoyl)benzene with different amines were used to synthesize 1,3,5-tri-(1-alkyl-5-methylpyrrol-2-yl)benzenes with different N-substituents in yields between 44 and 60%. Incomplete reaction of vinylmagnesium bromide with trimethyl 1,3,5-benzenetricarboxylate gave the methyl-3,5-di(pent-4-enoyl)benzoate, which was converted to methyl-3,5-dipyrrolylbenzoate following the reaction of Tsuji- Wacker and Paal-Knorr with yields between 30 and 60%. The photochemical and electrochemical properties of the 1,3,5-tri-(1-alkyl-5-methylpyrrol-2-yl)benzenes and methyl-3,5-dipyrrolylbenzoates were studied in collaboration with the research group of professor William Skene. The results have shown that both types of pyrrole have potential for the synthesis of conjugated polymers and dendrimers used in the manufacture of electroluminescent materials. Following these encouraging results, we performed the synthesis of 6,12-dimethyl-1,5-dipyrrolediazocane. Methyl N-(Boc)-β-alaninate was converted to its corresponding homoallylic ketone, which was oxidized to N-(Boc)aminoheptan-3,6-dione. The Paal-Knorr condensation between N-(Boc)aminoheptan-3,6-dione and aminoheptan-3,6-dione hydrochloride gave 6,12-dimethyl-1,5-dipyrrolediazocane in 17% yield. In sum, we have synthesized and characterized seven new molecules, six of them having photochemical and electrochemical properties interesting for the synthesis of conjugated polymers and dendrimers. The latter offering potential as precursor for the conception of compounds of therapeutic interest.

Spray Pyrolysed Zinc Oxide Thin Films : Effects of Doping and Ion Beam Irradiation

In recent years scientists have made rapid and significant advances in the field of semiconductor physics. One of the most important fields of current interest in materials science is the fundamental aspects and applications of conducting transparent oxide thin films (TCO). The characteristic properties of such coatings are low electrical resistivity and high transparency in the visible region. The first semitransparent and electrically conducting CdO film was reported as early as in 1907 [1]. Though early work on these films was performed out of purely scientific interest, substantial technological advances in such films were made after 1940. The technological interest in the study of transparent semiconducting films was generated mainly due to the potential applications of these materials both in industry and research. Such films demonstrated their utility as transparent electrical heaters for windscreens in the aircraft industry. However, during the last decade, these conducting transparent films have been widely used in a variety of other applications such as gas sensors [2], solar cells [3], heat reflectors [4], light emitting devices [5] and laser damage resistant coatings in high power laser technology [6]. Just a few materials dominate the current TCO industry and the two dominant markets for TCO’s are in architectural applications and flat panel displays. The architectural use of TCO is for energy efficient windows. Fluorine doped tin oxide (FTO), deposited using a pyrolysis process is the TCO usually finds maximum application. SnO2 also finds application ad coatings for windows, which are efficient in preventing radiative heat loss, due to low emissivity (0.16). Pyrolitic tin oxide is used in PV modules, touch screens and plasma displays. However indium tin oxide (ITO) is mostly used in the majority of flat panel display (FPD) applications. In FPDs, the basic function of ITO is as transparent electrodes. The volume of FPD’s produced, and hence the volume of ITO coatings produced, continues to grow rapidly. But the current increase in the cost of indium and the scarcity of this material created the difficulty in obtaining low cost TCOs. Hence search for alternative TCO materials has been a topic of active research for the last few decades. This resulted in the development of binary materials like ZnO, SnO2, CdO and ternary materials like II Zn2SnO4, CdSb2O6:Y, ZnSO3, GaInO3 etc. The use of multicomponent oxide materials makes it possible to have TCO films suitable for specialized applications because by altering their chemical compositions, one can control the electrical, optical, chemical and physical properties. But the advantages of using binary materials are the easiness to control the chemical compositions and depositions conditions. Recently, there were reports claiming the deposition of CdO:In films with a resistivity of the order of 10-5 ohm cm for flat panel displays and solar cells. However they find limited use because of Cd-Toxicity. In this regard, ZnO films developed in 1980s, are very useful as these use Zn, an abundant, inexpensive and nontoxic material. Resistivity of this material is still not very low, but can be reduced through doping with group-III elements like In, Al or Ga or with F [6]. Hence there is a great interest in ZnO as an alternative of ITO. In the present study, we prepared and characterized transparent and conducting ZnO thin films, using a cost effective technique viz Chemical Spray Pyrolysis (CSP). This technique is also suitable for large area film deposition. It involves spraying a solution, (usually aqueous) containing soluble salts of the constituents of the desired compound, onto a heated substrate.

Fabrication and the study of zinc sulphide based electroluminescent devices

This thesis contains the author's work in preparing efficient EL phosphors, the details of fabrication of low voltage operated thin film EL (TFEL) devices and DC TFEL devices. Some of the important work presented here are related to the white light emitting ZnS:Cu,Pr,Cl phosphor which can be colour tuned by changing the excitation frequency, observation of energy transfer from Cu/Ag ions to rare earth ions in ZnS:(Cu/Ag), RE,Cl phosphors, development of TFEL device which can be operated below 50V, optimization of the device parameters for long life, high brightness in terms of the active and insulating layer thicknesses, observation of dependence of threshold voltage for the onset of emission on frequency of excitation when a novel dielectric Eu2O3 film was used as insulator and the devices with multicolor emission using ZnS doped with rare earth as active layer. Characterization based on other devices based on ZnS:Sm, ZnS:Pr, ZnS:Dy and their emission characteristics are also illustrated

Photoluminescence studies on RF plasma-polymerized thin films

Conjugated polymers in the form of thin films play an important role in the field of materials science due to their interesting properties. Polymer thin films find extensive applications in the fabrication of devices, such as light emitting devices, rechargeable batteries, super capacitors, and are used as intermetallic dielectrics and EMI shieldings. Polymer thin films prepared by plasma-polymerization are highly cross-linked, pinhole free, and their permittivity lie in the ultra low k-regime. Electronic and photonic applications of plasma-polymerized thin films attracted the attention of various researchers. Modification of polymer thin films by swift heavy ions is well established and ion irradiation of polymers can induce irreversible changes in their structural, electrical, and optical properties. Polyaniline and polyfurfural thin films prepared by RF plasmapolymerization were irradiated with 92MeV silicon ions for various fluences of 1×1011 ions cm−2, 1×1012 ions cm−2, and 1×1013 ions cm−2. FTIR have been recorded on the pristine and silicon ion irradiated polymer thin films for structural evaluation. Photoluminescence (PL) spectra were recorded for RF plasma-polymerized thin film samples before and after irradiation. In this paper the effect of swift heavy ions on the structural and photoluminescence spectra of plasma-polymerized thin films are investigated.

Enhanced UV emission from ZnO nanoflowers synthesized by the hydrothermal process

ZnO nanoflowers were synthesized by the hydrothermal process at an optimized growth temperature of 200 ◦C and a growth/reaction time of 3 h. As-prepared ZnO nanoflowers were characterized by x-ray diffraction, scanning electron microscopy, UV–visible and Raman spectroscopy. X-ray diffraction and Raman studies reveal that the as-synthesized flower-like ZnO nanostructures are highly crystalline with a hexagonal wurtzite phase preferentially oriented along the (1 0 1 1) plane. The average length (234–347 nm) and diameter (77–106 nm) of the nanorods constituting the flower-like structure are estimated using scanning electron microscopy studies. The band gap of ZnO nanoflowers is estimated as 3.23 eV, the lowering of band gap is attributed to the flower-like surface morphology and microstructure of ZnO. Room temperature photoluminescence spectrum shows a strong UV emission peak at 392 nm, with a suppressed visible emission related to the defect states, indicating the defect free formation of ZnO nanoflowers that can be potentially used for UV light-emitting devices. The suppressed Raman bands at 541 and 583 cm−1 related to defect states in ZnO confirms that the ZnO nanoflowers here obtained have a reduced presence of defects

Synthesis, Characterization and Applications of Hybrid Nanocomposites of TiO2 With Conducting Polymers

A nanocomposite is a multiphase solid material where one of the phases has one, two or three dimensions of less than 100 nanometers (nm), or structures having nano-scale repeat distances between the different phases that make up the material. In the broadest sense this definition can include porous media, colloids, gels and copolymers, but is more usually taken to mean the solid combination of a bulk matrix and nano-dimensional phase(s) differing in properties due to dissimilarities in structure and chemistry. The mechanical, electrical, thermal, optical, electrochemical, catalytic properties of the nanocomposite will differ markedly from that of the component materials. Size limits for these effects have been proposed, <5 nm for catalytic activity, <20 nm for making a hard magnetic material soft, <50 nm for refractive index changes, and <100 nm for achieving superparamagnetism, mechanical strengthening or restricting matrix dislocation movement. Conducting polymers have attracted much attention due to high electrical conductivity, ease of preparation, good environmental stability and wide variety of applications in light-emitting, biosensor chemical sensor, separation membrane and electronic devices. The most widely studied conducting polymers are polypyrrole, polyaniline, polythiophene etc. Conducting polymers provide tremendous scope for tuning of their electrical conductivity from semiconducting to metallic region by way of doping and are organic electro chromic materials with chemically active surface. But they are chemically very sensitive and have poor mechanical properties and thus possessing a processibility problem. Nanomaterial shows the presence of more sites for surface reactivity, they possess good mechanical properties and good dispersant too. Thus nanocomposites formed by combining conducting polymers and inorganic oxide nanoparticles possess the good properties of both the constituents and thus enhanced their utility. The properties of such type of nanocomposite are strongly depending on concentration of nanomaterials to be added. Conducting polymer composites is some suitable composition of a conducting polymer with one or more inorganic nanoparticles so that their desirable properties are combined successfully. The composites of core shell metal oxide particles-conducting polymer combine the electrical properties of the polymer shell and the magnetic, optical, electrical or catalytic characteristics of the metal oxide core, which could greatly widen their applicability in the fields of catalysis, electronics and optics. Moreover nanocomposite material composed of conducting polymers & oxides have open more field of application such as drug delivery, conductive paints, rechargeable batteries, toners in photocopying, smart windows, etc.The present work is mainly focussed on the synthesis, characterization and various application studies of conducting polymer modified TiO2 nanocomposites. The conclusions of the present work are outlined below, Mesoporous TiO2 was prepared by the cationic surfactant P123 assisted hydrothermal synthesis route and conducting polymer modified TiO2 nanocomposites were also prepared via the same technique. All the prepared systems show XRD pattern corresponding to anatase phase of TiO2, which means that there is no phase change occurring even after conducting polymer modification. Raman spectroscopy gives supporting evidence for the XRD results. It also confirms the incorporation of the polymer. The mesoporous nature and surface area of the prepared samples were analysed by N2 adsorption desorption studies and the mesoporous ordering can be confirmed by low angle XRD measurementThe morphology of the prepared samples was obtained from both SEM & TEM. The elemental analysis of the samples was performed by EDX analysisThe hybrid composite formation is confirmed by FT-IR spectroscopy and X-ray photoelectron spectroscopyAll the prepared samples have been used for the photocatalytic degradation of dyes, antibiotic, endocrine disruptors and some other organic pollutants. Photocatalytic antibacterial activity studies were also performed using the prepared systemsAll the prepared samples have been used for the photocatalytic degradation of dyes, antibiotic, endocrine disruptors and some other organic pollutants. Photocatalytic antibacterial activity studies were also performed using the prepared systems Polyaniline modified TiO2 nanocomposite systems were found to have good antibacterial activity. Thermal diffusivity studies of the polyaniline modified systems were carried out using thermal lens technique. It is observed that as the amount of polyaniline in the composite increases the thermal diffusivity also increases. The prepared systems can be used as an excellent coolant in various industrial purposes. Nonlinear optical properties (3rd order nonlinearity) of the polyaniline modified systems were studied using Z scan technique. The prepared materials can be used for optical limiting Applications. Lasing studies of polyaniline modified TiO2 systems were carried out and the studies reveal that TiO2 - Polyaniline composite is a potential dye laser gain medium.

Low-Cost Micromechanically Tunable Optical Devices: Strained Resonator Engineering, Technological Implementation and Characterization

The rapid growth of the optical communication branches and the enormous demand for more bandwidth require novel networks such as dense wavelength division multiplexing (DWDM). These networks enable higher bitrate transmission using the existing optical fibers. Micromechanically tunable optical microcavity devices like VCSELs, Fabry-Pérot filters and photodetectors are core components of these novel DWDM systems. Several air-gap based tunable devices were successfully implemented in the last years. Even though these concepts are very promising, two main disadvantages are still remaining. On the one hand, the high fabrication and integration cost and on the other hand the undesired adverse buckling of the suspended membranes. This thesis addresses these two problems and consists of two main parts: • PECVD dielectric material investigation and stress control resulting in membranes shape engineering. • Implementation and characterization of novel tunable optical devices with tailored shapes of the suspended membranes. For this purposes, low-cost PECVD technology is investigated and developed in detail. The macro- and microstress of silicon nitride and silicon dioxide are controlled over a wide range. Furthermore, the effect of stress on the optical and mechanical properties of the suspended membranes and on the microcavities is evaluated. Various membrane shapes (concave, convex and planar) with several radii of curvature are fabricated. Using this resonator shape engineering, microcavity devices such as non tunable and tunable Fabry-Pérot filters, VCSELs and PIN photodetectors are succesfully implemented. The fabricated Fabry-Pérot filters cover a spectral range of over 200nm and show resonance linewidths down to 1.5nm. By varying the stress distribution across the vertical direction within a DBR, the shape and the radius of curvature of the top membrane are explicitely tailored. By adjusting the incoming light beam waist to the curvature, the fundamental resonant mode is supported and the higher order ones are suppressed. For instance, a tunable VCSEL with 26 nm tuning range, 400µW maximal output power, 47nm free spectral range and over 57dB side mode suppresion ratio (SMSR) is demonstrated. Other technologies, such as introducing light emitting organic materials in microcavities are also investigated.

High Indium Concentration InGaN/GaN Grown on Sapphire Substrate by MOCVD

The InGaN system provides the opportunity to fabricate light emitting devices over the whole visible and ultraviolet spectrum due to band-gap energies E[subscript g] varying between 3.42 eV for GaN and 1.89 eV for InN. However, high In content in InGaN layers will result in a significant degradation of the crystalline quality of the epitaxial layers. In addition, unlike other III-V compound semiconductors, the ratio of gallium to indium incorporated in InGaN is in general not a simple function of the metal atomic flux ratio, f[subscript Ga]/f[subscript In]. Instead, In incorporation is complicated by the tendency of gallium to incorporate preferentially and excess In to form metallic droplets on the growth surface. This phenomenon can definitely affect the In distribution in the InGaN system. Scanning electron microscopy, room temperature photoluminescence, and X-ray diffraction techniques have been used to characterize InGaN layer grown on InN and InGaN buffers. The growth was done on c-plane sapphire by MOCVD. Results showed that green emission was obtained which indicates a relatively high In incorporation.