Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

Mo bilayer for thin film photovoltaics revisited

Thin film solar cells based on Cu(In,Ga)Se2 as an absorber layer use Mo as the back contact. This metal is widely used in research and in industry but despite this, there are only a few published studies on the properties of Mo. Properties such as low resistivity and good adhesion to soda lime glass are hard to obtain at the same time. These properties are dependent on the deposition conditions and are associated with the overall stress state of the film. In this report, a study of the deposition of a Mo bilayer is carried out by analysing first single and then bilayers. The best properties of the bilayer were achieved when the bottom layer was deposited at 10 × 10−3 mbar with a thickness of 500 nm and the top layer deposited at 1 × 10−3 mbar with a thickness of 300 nm. The films deposited under these conditions showed good adhesion and a sheet resistivity lower than 0.8 .

Study of optical and structural properties of Cu2ZnSnS4 thin films

Cu2ZnSnS4 is a promising semiconductor to be used as absorber in thin film solar cells. In this work, we investigated optical and structural properties of Cu2ZnSnS4 thin films grown by sulphurization of metallic precursors deposited on soda lime glass substrates. The crystalline phases were studied by X-ray diffraction measurements showing the presence of only the Cu2ZnSnS4 phase. The studied films were copper poor and zinc rich as shown by inductively coupled plasma mass spectroscopy. Scanning electron microscopy revealed a good crystallinity and compactness. An absorption coefficient varying between 3 and 4×104cm−1 was measured in the energy range between 1.75 and 3.5 eV. The band gap energy was estimated in 1.51 eV. Photoluminescence spectroscopy showed an asymmetric broad band emission. The dependence of this emission on the excitation power and temperature was investigated and compared to the predictions of the donor-acceptor-type transitions and radiative recombinations in the model of potential fluctuations. Experimental evidence was found to ascribe the observed emission to radiative transitions involving tail states created by potential fluctuations.

Assessment of the potential of tin sulphide thin films prepared by sulphurization of metallic precursors as cell absorbers

In this work, SnxSy thin films have been grown on soda-lime glass substrates by sulphurization of metallic precursors in a nitrogen plus sulphur vapour atmosphere. Different sulphurization temperatures were tested, ranging from 300 °C to 520 °C. The resulting phases were structurally investigated by X-Ray Diffraction and Raman spectroscopy. Composition was studied using Energy Dispersive Spectroscopy being then correlated with the sulphurization temperature. Optical measurements were performed to obtain transmittance and reflectance spectra, from which the energy band gaps, were estimated. The values obtained were 1.17 eV for the indirect transition and for the direct transition the values varied from 1.26 eV to 1.57 eV. Electrical characterization using Hot Point Probe showed that all samples were p-type semiconductors. Solar cells were built using the structure: SLG/Mo/SnxSy/CdS/ZnO:Ga and the best result for solar cell efficiency was 0.17%.

Cu2ZnSnS4 solar cells prepared with sulphurized dc-sputtered stacked metallic precursors

In the present work we report the details of the preparation and characterization results of Cu2ZnSnS4 (CZTS) based solar cells. The CZTS absorber was obtained by sulphurization of dc magnetron sputtered Zn/Sn/Cu precursor layers. The morphology, composition and structure of the absorber layer were studied by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and Raman scattering. The majority carrier type was identified via a hot point probe analysis. The hole density, space charge region width and band gap energy were estimated from the external quantum efficiency measurements. A MoS2 layer that formed during the sulphurization process was also identified and analyzed in this work. The solar cells had the following structure: soda lime glass/Mo/CZTS/CdS/i-ZnO/ZnO:Al/Al grid. The best solar cell showed an opencircuit voltage of 345 mV, a short-circuit current density of 4.42 mA/cm2, a fill factor of 44.29% and an efficiency of 0.68% under illumination in simulated standard test conditions: AM 1.5 and 100 mW/cm2.

Análise do sistema de tratamento de efluentes gasosos de uma central de valorização energética de resíduos sólidos urbanos

Trabalho Final de Mestrado para obtenção do grau de Mestre Em Engenharia Química e Biológica Ramo de processos Químicos

Current mortars in conservation: an overview

Renders are an important item in historical buildings and the need for their periodical re-application is a basic conservation procedure. In modern times there has been a trend towards the replacement of traditional pure lime mortars by new formulations including Portland cement or hydraulic lime. Apart from those interventions on specific and very important monuments, in which the use oftraditional non-hydraulic mortars can be enforced, in most of the projects involving less than first order magnitude heritage the use of some sort of hydraulic components is becoming the rule rather than the exception. The present paper describes and analyses the results of an experimental study with ten formulations of current mortars - including some that can hardly be considered as adequate conservation procedures - allowing a direct comparison in terms of some of the most relevant characteristics.

Gestão de resíduos produzidos num sistema de drenagem e tratamento de águas residuais

O presente trabalho centra-se na gestão de resíduos produzidos no sistema de drenagem e tratamento de águas residuais do município de Vila Nova de Gaia. A entidade onde decorreu o trabalho é uma empresa responsável pela distribuição de água e pela drenagem e tratamento de águas residuais. A empresa está certificada pela norma NP EN ISO 14001, desde 2001, sendo então um dos objectivos o enquadramento da gestão dos resíduos em estudo na referida norma, acompanhando os requisitos da mesma com vista ao seu total cumprimento. Outros dos objectivos foi estudar qual a opção de tratamento mais adequada a aplicar ao resíduo no seu local de armazenamento temporário com vista a minorar os seus impactes ambientais. De acordo com a caracterização analítica do resíduo e com os aspetos legais aplicáveis, foram também analisados os destinos finais possíveis e ambientalmente adequados ao resíduo. A medida proposta para a minimização de impactes no local de armazenamento temporário do resíduo foi a estabilização com cal nos leitos de secagem, disponíveis numa antiga ETAR de loteamento. O doseamento de cal a aplicar ao resíduo será de 10 kg de cal apagada comercial (Ca (OH)2) por uma tonelada de resíduo fresco com um período mínimo de secagem de 2 meses. Outra das medidas de minimização de impactes selecionada foi a implantação de uma cortina arbórea ao redor da instalação. Sendo o resíduo em estudo muito heterogéneo, constituído principalmente por areias, terras e gradados, a valorização foi equacionada mas não foram encontrados alternativas viáveis. O destino final considerado como mais adequado tendo em conta todas as características do resíduo e eluato, analisadas de acordo com o previsto no Decreto-Lei n.º 183/2009 de 10 de Agosto, foi o aterro para resíduos não perigosos. Foi também objecto do estudo a identificação e análise de todos os aspectos ambientais relacionados com a gestão de resíduos e a avaliação da sua significância. Dos aspectos ambientais identificados como significativos, destacam-se aqueles que ocorrem presentemente, os resíduos armazenados (gradados/limpeza de redes), e os que podem ocorrer em situações de emergência, fuga/derrame de óleos/combustíveis e cheiros/odores. De forma a minimizar os aspectos ambientais identificados, e de acordo com a norma NP EN ISO 14001, foram propostas ações que constam de um programa de gestão elaborado para este trabalho, onde se definem os objectivos, metas e prazos. As principais medidas propostas no programa de gestão foram: Estabilização com cal (inicial e reforço se necessário); melhoria do espaço envolvente; análise de questões de saúde ocupacional/segurança; adjudicação de prestação de serviços da recolha por operador licenciado; implantação da cortina arbórea; registo no SIRAPA; criação de planos de emergência ambiental e de segurança.

Influence of the deposition pressure on the properties of transparent and conductive ZnO: Ga thin-film produced by r.f. sputtering at room temperature

Thin Solid Films, vol. 427, nº 1-2

Caracterización y determinación del proceso para la producción de cal comercial a partir de la piedra caliza

La cal es un material producido a partir de la calcinación de la roca caliza y tiene diversas utilidades en el mundo de la industria como la siderúrgica, papelera, alimentaria, en la construcción, entre otras. Es fundamental conocer todas las características de la caliza para poder determinar su grado de calcinación. Con el presente trabajo se pretende estudiar las propiedades de la caliza para su posterior calcinación y el dimensionamiento de una planta de producción de cal desde que el mineral llega de la explotación hasta que sale al mercado. Para determinar los equipos se calcularon sus dimensiones para una producción de 600 t/h de cal, sabiendo que la planta principal de machaqueo solo trabajará 5 días de la semana en jornadas de 8 horas, mientras que a partir del horno de calcinación estará en funcionamiento los 7 días de la semana, 24 horas al día. A partir de esas consideraciones se obtienen las dimensiones de todos los equipos y se realiza un estudio para la elección de un horno, o un horno de eje vertical y un horno rotativo, así como el combustible empleado, ya que es una parte fundamental para determinar los costes para la producción de cal. También fue objeto de este trabajo, el estudio ambiental de la instalación de la planta, en función de la mezcla de combustible empleada y del impacto en el entorno de la misma, así como un estudio de viabilidad de la planta, estimando unos costes de la misma y un precio de mercado “ex‐Works”.

Couro pergaminho e couro transparente: desenvolvimento de processo

Mestrado em Engenharia Química - Ramo Optimização Energética na Indústria Química

Utilization of food industry wastes for the production of zero-valent iron nanoparticles

The proper disposal of the several types of wastes produced in industrial activities increases production costs. As a consequence, it is common to develop strategies to reuse these wastes in the same process and in different processes or to transform them for use in other processes. This work combines the needs for new synthesis methods of nanomaterials and the reduction of production cost using wastes from citrine juice (orange, lime, lemon and mandarin) to produce a new added value product, green zero-valent iron nanoparticles that can be used in several applications, including environmental remediation. The results indicate that extracts of the tested fruit wastes (peel, albedo and pulp fractions) can be used to produce zero-valent iron nanoparticles (nZVIs). This shows that these wastes can be an added value product. The resulting nZVIs had sizes ranging from 3 up to 300 nm and distinct reactivities (pulp > peel > albedo extracts). All the studied nanoparticles did not present a significant agglomeration/settling tendency when compared to similar nanoparticles, which indicates that they remain in suspension and retain their reactivity.

Hydraulic binders

Hydraulic binders play a vital role in the economic and social development because they are essential components of concrete, the most widely used construction material. Nowadays, Portland cement is the most predominantly used hydraulic binder due to its properties and widespread availability. Cement manufacture consumes large amount of non-renewable raw materials and energy, and it is a carbon-intensive process. Many efforts are, therefore, being undertaken towards the developing “greener” hydraulic binders. Concomitantly, binders must also correspond to market demand in terms of performance and aesthetic as well as fulfill mandatory regulations. In order to pursue these goals, different approaches have been followed including the improvement of the cement manufacturing process, production of blended cements, and testing innovative hydraulic binders with a different chemistry. This chapter presents a brief history of hydraulic binder’s discovery and use as well as the environmental and economic context of cement industry. It, then, describes the chemistry and properties of currently most used hydraulic binders—common cements and hydraulic limes—and that of the more promising binders for future applications, namely special Portland cements, aluminous cements, calcium sulfoaluminate cements, and alkali-activated cements.

ECO: argamassas de cal hidráulica para reabilitação de edifícios

Dissertação de Natureza Científica para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações

Chemical analysis of 17th century Millefiori glasses excavated in the Monastery of Sta. Clara‐a‐Velha: comparison with Venetian and façon‐de‐Venise production

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Conservação e Restauro,Área de especialização Cerâmica e Vidro