Scale-up of mixer granulators for effective liquid distribution

There is considerable anecdotal evidence from industry that poor wetting and liquid distribution can lead to broad granule size distributions in mixer granulators. Current scale-up scenarios lead to poor liquid distribution and a wider product size distribution. There are two issues to consider when scaling up: the size and nature of the spray zone and the powder flow patterns as a function of granulator scale. Short, nucleation-only experiments in a 25L PMA Fielder mixer using lactose powder with water and HPC solutions demonstrated the existence of different nucleation regimes depending on the spray flux Psi(a)-from drop-controlled nucleation to caking. In the drop-controlled regime at low Psi(a) values. each drop forms a single nucleus and the nuclei distribution is controlled by the spray droplet size distribution. As Psi(a) increases, the distribution broadens rapidly as the droplets overlap and coalesce in the spray zone. The results are in excellent agreement with previous experiments and confirm that for drop-controlled nucleation. Psi(a) should be less than 0.1. Granulator flow studies showed that there are two powder flow regimes-bumping and roping. The powder flow goes through a transition from bumping to roping as impeller speed is increased. The roping regime gives good bed turn over and stable flow patterns. This regime is recommended for good liquid distribution and nucleation. Powder surface velocities as a function of impeller speed were measured using high-speed video equipment and MetaMorph image analysis software, Powder surface velocities were 0.2 to 1 ms(-1)-an order of magnitude lower than the impeller tip speed. Assuming geometrically similar granulators, impeller speed should be set to maintain constant Froude number during scale-up rather than constant tip speed to ensure operation in the roping regime. (C) 2002 Published by Elsevier Science B.V.

Effect of the Impact Conditions on the Mechanical Properties of Injection-Molded Parts

This work focused on the study of the impact event on molded parts in the framework of automotive components. The influence of the impact conditions and processing parameters on the mechanical behavior of talc-filled polypropylene specimens was analyzed. The specimens were lateral-gate discs produced by injection molding, and the mechanical characterization was performed through instrumented falling weight impact tests concomitantly assisted with high-speed videography. Results analyzed using the analysis of variance (ANOVA) method have shown that from the considered parameters, only the dart diameter and test temperature have significant influence on the falling weight impact properties. Higher dart diameter leads to higher peak force and peak energy results. Conversely, higher levels of test temperatures lead to lower values of peak force and peak energy. By means of high-speed videography, a more brittle fracture was observed for experiments with higher levels of test velocity and dart diameter and lower levels of test temperature. The injection-molding process conditions assessed in this study have an influence on the impact response of moldings, mainly on the deformation capabilities of the moldings.

Distribuição de vídeo sobre uma rede IEEE 802.11n

A recente norma IEEE 802.11n oferece um elevado débito em redes locais sem fios sendo por isso esperado uma adopção massiva desta tecnologia substituindo progressivamente as redes 802.11b/g. Devido à sua elevada capacidade esta recente geração de redes sem fios 802.11n permite um crescimento acentuado de serviços audiovisuais. Neste contexto esta dissertação procura estudar a rede 802.11n, caracterizando o desempenho e a qualidade associada a um serviço de transmissão de vídeo, recorrendo para o efeito a uma arquitectura de simulação da rede 802.11n. Desta forma é caracterizado o impacto das novas funcionalidades da camada MAC introduzidas na norma 801.11n, como é o caso da agregação A-MSDU e A-MPDU, bem como o impacto das novas funcionalidades da camada física como é o caso do MIMO; em ambos os casos uma optimização da parametrização é realizada. Também se verifica que as principais técnicas de codificação de vídeo H.264/AVC para optimizar o processo de distribuição de vídeo, permitem optimizar o desempenho global do sistema de transmissão. Aliando a optimização e parametrização da camada MAC, da camada física, e do processo de codificação, é possível propor um conjunto de configurações que permitem obter o melhor desempenho na qualidade de serviço da transmissão de conteúdos de vídeo numa rede 802.11n. A arquitectura de simulação construída nesta dissertação é especificamente adaptada para suportar as técnicas de agregação da camada MAC, bem como para suportar o encapsulamento em protocolos de rede que permitem a transmissão dos pacotes de vídeo RTP, codificados em H.264/AVC.

Parametric analog signal amplification applied to nanoscale cmos wireless digital transceivers

Thesis presented in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the subject of Electrical and Computer Engineering by the Universidade Nova de Lisboa,Faculdade de Ciências e Tecnologia

Comunicações marítimas wi-fi usando a banda 5.8 ghz

Tendo em conta a popularidade que as comunicações Wi-Fi têm na atualidade em vários dispositivos como computadores portáteis, telemóveis ou tablets, sendo estes utilizados praticamente por qualquer pessoa, surgiu a ideia de utilizar esta tecnologia de baixo custo e isenta de licenciamento num cenário de comunicações marítimas. Neste contexto, esta permite fornecer o acesso à Internet em banda larga a grupos de embarcações, que atualmente recorrem a tecnologias de elevado custo (satélite) e/ou de banda estreita (rádios VHF). Com o acesso em banda larga, os proprietários poderão utilizar aplicações informáticas de interesse à atividade de negócio ou de lazer, até então só disponíveis junto à costa onde existe cobertura celular. Nesta tese pretende-se fazer um estudo teórico e prático sobre o alcance e respetivo desempenho de comunicações de banda larga em ambiente marítimo, utilizando parte da gama de frequências dos 5,8 GHz, isenta de licença, e a norma IEEE 802.11n. Para se utilizar equipamento produzido em massa a operar nessa gama, existem duas normas disponíveis, a IEEE 802.11a e a IEEE 802.11n. Optou-se pelo IEEE 802.11n pois os esquemas de codificação ao nível físico permitem débitos mais elevados e MIMO. Para a realização dos testes experimentais, foi necessário elaborar um protótipo de comunicação ponto a ponto, constituído por dois nós de comunicação. Um deles foi instalado numa embarcação de pesca em colaboração com a Associação Propeixe e o outro no Edifício Transparente, no Porto, em colaboração com a entidade gestora do edifício e a Associação Porto Digital. Tanto quanto se conhece é o primeiro teste de comunicações Wi-Fi realizado nestas condições a nível mundial. Os objetivos do trabalho foram atingidos. Foi possível estabelecer comunicações Wi-Fi na banda dos 5,8 GHz até cerca de 7 km com débito médio mínimo de 1 Mbit/s. O ambiente de testes desenvolvido e os resultados obtidos servirão de base para futuros trabalhos de investigação na área das comunicações marítimas.

Pipelined analog-to-digital conversion using current-mode reference shifting

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Empirical models for quantification of machining damage in composite materials

Dissertação para obtenção do Grau de Doutor em Engenharia Mecânica

Multipacket reception in LTE femtocell networks

Dissertação apresentada para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores

QoS in LEO satellite networks with multipacket reception

Dissertação apresentada para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Advances in thermoplastic pultruded composites

Pultrusion is a versatile continuous high speed production technology allowing the production of fibre reinforced complex profiles. Thermosetting resins are normally used as matrices in the production of structural constant cross section profiles. Although only recently thermoplastic matrices have been used in long and continuous fibre reinforced composites replacing with success thermosetting matrices, the number of their applications is increasing due to their better ecological and mechanical performance. Composites with thermoplastic matrices offers increased fracture toughness, higher impact tolerance, short processing cycle time and excellent environmental stability. They are recyclable, post-formable and can be joined by welding. The use of long/continuous fibre reinforced thermoplastic matrix composites involves, however, great technological and scientific challenges since thermoplastics present much higher viscosity than thermosettings, which makes much difficult and complex the impregnation of reinforcements and consolidation tasks. In this work continuous fibres reinforced thermoplastic matrix towpregs were produced using equipment developed by the Institute for Polymers and Composites (IPC). The processing of the towpregs was made by pultrusion, in a developed prototype equipment existing in the Engineering School of the Polytechnic Institute of Porto (ISEP). Different thermoplastic matrices and fibres raw-materials were used in this study to manufacture pultruded composites for commercial applications (glass and carbon fibre/ polypropylene) and for advanced markets (carbon fibre/Primospire®). To improve the temperature distribution profile in heating die, different modifications were performed. In order to optimize both processes, towpregs production and pultruded composites profiles were analysed to determine the influence of the most relevant processing arameters in the final properties. The final pultruded composite profiles were submitted to mechanical tests to obtain the relevant properties.

Effect of hormonal changes on corneal biomechanical properties and anterior segment ocular perameters

Dissertação de mestrado em Optometria Avançada

Simulations of parasitic and intrinsic capacitances related to Multiple-Gate-Field-Effect Transistor architectures

Report for the scientific sojourn carried out at the Université Catholique de Louvain, Belgium, from March until June 2007. In the first part, the impact of important geometrical parameters such as source and drain thickness, fin spacing, spacer width, etc. on the parasitic fringing capacitance component of multiple-gate field-effect transistors (MuGFET) is deeply analyzed using finite element simulations. Several architectures such as single gate, FinFETs (double gate), triple-gate represented by Pi-gate MOSFETs are simulated and compared in terms of channel and fringing capacitances for the same occupied die area. Simulations highlight the great impact of diminishing the spacing between fins for MuGFETs and the trade-off between the reduction of parasitic source and drain resistances and the increase of fringing capacitances when Selective Epitaxial Growth (SEG) technology is introduced. The impact of these technological solutions on the transistor cut-off frequencies is also discussed. The second part deals with the study of the effect of the volume inversion (VI) on the capacitances of undoped Double-Gate (DG) MOSFETs. For that purpose, we present simulation results for the capacitances of undoped DG MOSFETs using an explicit and analytical compact model. It monstrates that the transition from volume inversion regime to dual gate behaviour is well simulated. The model shows an accurate dependence on the silicon layer thickness,consistent withtwo dimensional numerical simulations, for both thin and thick silicon films. Whereas the current drive and transconductance are enhanced in volume inversion regime, our results show thatintrinsic capacitances present higher values as well, which may limit the high speed (delay time) behaviour of DG MOSFETs under volume inversion regime.

Desenvolupament d'eines d'alta ressolució per al cribatge (screening) de l'activitat de fàrmacs

Projecte de recerca elaborat a partir d’una estada a la Satandford University, EEUU, entre 2007 i 2009. Els darrers anys, hi ha hagut un avanç espectacular en la tecnologia aplicada a l’anàlisi del genoma i del proteoma (microarrays, PCR quantitativa real time, electroforesis dos dimensions, espectroscòpia de masses, etc.) permetent la resolució de mostres complexes i la detecció quantitativa de diferents gens i proteïnes en un sol experiment. A més a més, la seva importància radica en la capacitat d’identificar potencials dianes terapèutiques i possibles fàrmacs, així com la seva aplicació en el disseny i desenvolupament de noves eines de diagnòstic. L’aplicabilitat de les tècniques actuals, però, està limitada al nivell al que el teixit pot ser disseccionat. Si bé donen valuosa informació sobre expressió de gens i proteïnes implicades en una malaltia o en resposta a un fàrmac per exemple, en cap cas, s’obté una informació in situ ni es pot obtenir informació espacial o una resolució temporal, així com tampoc s’obté informació de sistemes in vivo. L’objectiu d’aquest projecte és desenvolupar i validar un nou microscopi, d’alta resolució, ultrasensible i de fàcil ús, que permeti tant la detecció de metabòlits, gens o proteïnes a la cèl•lula viva en temps real com l’estudi de la seva funció. Obtenint així una descripció detallada de les interaccions entre proteïnes/gens que es donen dins la cèl•lula. Aquest microscopi serà un instrument sensible, selectiu, ràpid, robust, automatitzat i de cost moderat que realitzarà processos de cribatge d’alt rendiment (High throughput screening) genètics, mèdics, químics i farmacèutics (per aplicacions diagnòstiques i de identificació i selecció de compostos actius) de manera més eficient. Per poder realitzar aquest objectius el microscopi farà ús de les més noves tecnologies: 1)la microscopia òptica i d’imatge, per millorar la visualització espaial i la sensibilitat de l’imatge; 2) la utilització de nous mètodes de detecció incloent els més moderns avanços en nanopartícules; 3) la creació de mètodes informàtics per adquirir, emmagatzemar i processar les imatges obtingudes.

Digital Strategy for Schools 2015 - 2020

Among the key points of the Digital Strategy are: Dedicated multi-annual funding to schools to invest in technology Build on the successful roll-out of high-speed broadband to every second-level school by investing in high-speed wifi networks in every school Integration of digital skills in the curriculum and in assessment Develop opportunities for students to take an in-depth ICT course at Leaving Cert, as well as embedding digital skills within other subjects Promotion of the use of e-portfolios at primary and post-primary level Provide enhanced digital content to schools, including working with cultural institutions, sporting bodies and other to expand this range of resources Embed ICT skills as part of initial teacher education and ongoing training for teachers

How useful is satellite positioning system (GPS) to track gait parameters? A review.

Over the last century, numerous techniques have been developed to analyze the movement of humans while walking and running. The combined use of kinematics and kinetics methods, mainly based on high speed video analysis and forceplate, have permitted a comprehensive description of locomotion process in terms of energetics and biomechanics. While the different phases of a single gait cycle are well understood, there is an increasing interest to know how the neuro-motor system controls gait form stride to stride. Indeed, it was observed that neurodegenerative diseases and aging could impact gait stability and gait parameters steadiness. From both clinical and fundamental research perspectives, there is therefore a need to develop techniques to accurately track gait parameters stride-by-stride over a long period with minimal constraints to patients. In this context, high accuracy satellite positioning can provide an alternative tool to monitor outdoor walking. Indeed, the high-end GPS receivers provide centimeter accuracy positioning with 5-20 Hz sampling rate: this allows the stride-by-stride assessment of a number of basic gait parameters--such as walking speed, step length and step frequency--that can be tracked over several thousand consecutive strides in free-living conditions. Furthermore, long-range correlations and fractal-like pattern was observed in those time series. As compared to other classical methods, GPS seems a promising technology in the field of gait variability analysis. However, relative high complexity and expensiveness--combined with a usability which requires further improvement--remain obstacles to the full development of the GPS technology in human applications.