Strap repairs using embedded patches: numerical analysis and experimental results

Adhesively bonded repairs offer an attractive option for repair of aluminium structures, compared to more traditional methods such as fastening or welding. The single-strap (SS) and double-strap (DS) repairs are very straightforward to execute but stresses in the adhesive layer peak at the overlap ends. The DS repair requires both sides of the damaged structures to be reachable for repair, which is often not possible. In strap repairs, with the patches bonded at the outer surfaces, some limitations emerge such as the weight, aerodynamics and aesthetics. To minimize these effects, SS and DS repairs with embedded patches were evaluated in this work, such that the patches are flush with the adherends. For this purpose, in this work standard SS and DS repairs, and also with the patches embedded in the adherends, were tested under tension to allow the optimization of some repair variables such as the overlap length (LO) and type of adhesive, thus allowing the maximization of the repair strength. The effect of embedding the patch/patches on the fracture modes and failure loads was compared with finite elements (FE) analysis. The FE analysis was performed in ABAQUS® and cohesive zone modelling was used for the simulation of damage onset and growth in the adhesive layer. The comparison with the test data revealed an accurate prediction for all kinds of joints and provided some principles regarding this technique.

Numerical and Experimental Analysis of Balanced and Unbalanced Adhesive Single-Lap Joints between Aluminium Adherends

The single-lap joint is the most commonly used, although it endures significant bending due to the non-collinear load path, which negatively affects its load bearing capabilities. The use of material or geometric changes is widely documented in the literature to reduce this handicap, acting by reduction of peel and shear peak stresses or alterations of the failure mechanism emerging from local modifications. In this work, the effect of using different thickness adherends on the tensile strength of single-lap joints, bonded with a ductile and brittle adhesive, was numerically and experimentally evaluated. The joints were tested under tension for different combinations of adherend thickness. The effect of the adherends thickness mismatch on the stress distributions was also investigated by Finite Elements (FE), which explained the experimental results and the strength prediction of the joints. The numerical study was made by FE and Cohesive Zone Modelling (CZM), which allowed characterizing the entire fracture process. For this purpose, a FE analysis was performed in ABAQUS® considering geometric non-linearities. In the end, a detailed comparative evaluation of unbalanced joints, commonly used in engineering applications, is presented to give an understanding on how modifications in the bonded structures thickness can influence the joint performance.

Fire safety barrier availability analysis

This paper shows several ways to analyse the performance of a safety barrier, depending on the objective to be achieved and present a method to analyse binary components usually present on sensor systems of safety barriers. An application example of a water-based fire system is presented and the Probability of Failure on Demand (PFD) of the sensor system is determined based on the analysis of pressure switches installed in this safety barrier. The knowledge of such information will allow the determination of safety barrier’s availability.

Modelling a cable structure for a new wind energy production device

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Mecânica Especialização em Concepção e Produção

Infective endocarditis (IE) first diagnosed at autopsy: analysis of 31 cases in Ribeirão Preto, Brazil

Thirty one infective endocarditis (IE) fatal cases whose diagnosis was first obtained at autopsy were studied. The clinical data of these patients (Group 1) showed significant differences compared to other 141 IE cases (Group 2). The average age of 53 years in Group 1 patients was 18 years higher than that of Group 2. The Group 1 patients had a low frequency of IE predisposing heart disease. Both patient groups presented fever (about 87%), but a significant low frequency of cardiac murmur (25.8%) was observed in Group 1 patients and echocardiography tests were performed in only 16.1%, suggesting that IE diagnosis was not suspected. Likewise, although most Group 1 patients appeared with severe acute illness, they did not present the classic IE clinical presentation. Blood cultures were performed in only 64.5% of the Group 1 patients. However, bacteria were isolated in 70% of these blood cultures and Staphylococcus aureus was isolated in 71.4%. The bacteria attacked mitral and aortic valves. Complications such as embolizations and cardiac failure occurred in almost half of the cases and they also presented with infections of the lungs, urinary tract, and central nervous system. Medical procedures were performed in practically all fatal cases whose diagnosis was first obtained at autopsy. Sepsis occurred in about half of the patients and it was followed by shock in more than 25%. This form of IE must be suspected in mature and in old febrile hospitalized patients having infection predisposing diseases, embolization, and suffering medical procedures.

The Prognostic Impact of Renal Failure in Patients with ST-Segment Elevation Acute Myocardial Infarction

INTRODUCTION: Renal insufficiency (RI) is associated with higher morbidity and mortality in patients (P) with coronary artery disease and in P submitted to angioplasty. In ST-segment elevation acute myocardial infarction (STEAMI), this impact has not been well demonstrated. AIM: To evaluate the impact of RI in P with STEAMI. METHODS: We evaluated 160 P admitted with STEAMI, mean age of 62+/-14 years, 76% male. We determined creatinine levels on admission. RI was defined as a level >1.5 mg/dl. Analysis of clinical, electrocardiographic and laboratory variables was performed, in relation to the endpoint defined as the occurrence of death at 30-day follow-up. RESULTS: There were 16 deaths (10%) at 30-day follow-up. P with RI (n=21) were older (68+/-11 vs 61+/-14 years, p<0.001), more often had diabetes (57 vs 24 %, p=0.004) and presented more often with Killip class > or =2 (57 vs 12%, p<0.001). The use of statins (62 vs 83%, p=0.05) and beta-blockers (24 vs 65%, p<0.001) was lower in P with RI. Mortality was higher in RI P (62 vs 2%, p<0.001). The univariate predictors of death were age > or =75 years, diabetes, Killip class > or =2 on admission, RI, non-use of statins and beta-blockers and use of diuretics. In multivariate analysis, independent predictors of death at 30 days were RI (HR 29.6, 95% CI 6.3-139.9, p<0.001) and non-use of beta-blockers (HR 0.13, 95% CI 0.02-1.01, p=0.01). CONCLUSION: In P admitted for STEAMI, the presence of RI was an independent predictor of death at 30 days whereas the usage of beta-blockers was protective.

Entropy Analysis of Industrial Accident Data Series

Complex industrial plants exhibit multiple interactions among smaller parts and with human operators. Failure in one part can propagate across subsystem boundaries causing a serious disaster. This paper analyzes the industrial accident data series in the perspective of dynamical systems. First, we process real world data and show that the statistics of the number of fatalities reveal features that are well described by power law (PL) distributions. For early years, the data reveal double PL behavior, while, for more recent time periods, a single PL fits better into the experimental data. Second, we analyze the entropy of the data series statistics over time. Third, we use the Kullback–Leibler divergence to compare the empirical data and multidimensional scaling (MDS) techniques for data analysis and visualization. Entropy-based analysis is adopted to assess complexity, having the advantage of yielding a single parameter to express relationships between the data. The classical and the generalized (fractional) entropy and Kullback–Leibler divergence are used. The generalized measures allow a clear identification of patterns embedded in the data.

Failure of nitric oxide production by macrophages and decrease in CD4+ T cells in oral paracoccidioidomycosis: possible mechanisms that permit local fungal multiplication

Paracoccidioidomycosis is a chronic granulomatous disease that induces a specific inflammatory and immune response. The participation of nitric oxide (NO), a product of the inducible nitric oxide synthase enzyme (iNOS), as an important fungicidal molecule against Paracoccidioides brasiliensis has been demonstrated. In order to further characterize the Oral Paracoccidioidomycosis (OP), we undertook an immunohistochemical study of iNOS+, CD45RO+, CD3+, CD8+, CD20+, CD68+ cells and mast cells. The samples were distributed in groups according to the number of viable fungi per mm². Our results showed weak immunolabeling for iNOS in the multinucleated giant cells (MNGC) and in most of the mononuclear (MN) cells, and the proportion of iNOS+ MN/MNGC cells in the OP were comparable to Control (clinically healthy oral tissues). Additionally, our analysis revealed a similarity in the number of CD4+ cells between the Control and the OP groups with higher numbers of fungi. These findings suggest that a low expression of iNOS and a decrease in the CD4+ T cells in OP may represent possible mechanisms that permit the local fungal multiplication and maintenance of active oral lesions.

Prognostic Value of a New Cardiopulmonary Exercise Testing Parameter in Chronic Heart Failure: Oxygen Uptake Efficiency at Peak Exercise - Comparison with Oxygen Uptake Efficiency Slope

INTRODUCTION: A growing body of evidence shows the prognostic value of oxygen uptake efficiency slope (OUES), a cardiopulmonary exercise test (CPET) parameter derived from the logarithmic relationship between O(2) consumption (VO(2)) and minute ventilation (VE) in patients with chronic heart failure (CHF). OBJECTIVE: To evaluate the prognostic value of a new CPET parameter - peak oxygen uptake efficiency (POUE) - and to compare it with OUES in patients with CHF. METHODS: We prospectively studied 206 consecutive patients with stable CHF due to dilated cardiomyopathy - 153 male, aged 53.3±13.0 years, 35.4% of ischemic etiology, left ventricular ejection fraction 27.7±8.0%, 81.1% in sinus rhythm, 97.1% receiving ACE-Is or ARBs, 78.2% beta-blockers and 60.2% spironolactone - who performed a first maximal symptom-limited treadmill CPET, using the modified Bruce protocol. In 33% of patients an cardioverter-defibrillator (ICD) or cardiac resynchronization therapy device (CRT-D) was implanted during follow-up. Peak VO(2), percentage of predicted peak VO(2), VE/VCO(2) slope, OUES and POUE were analyzed. OUES was calculated using the formula VO(2) (l/min) = OUES (log(10)VE) + b. POUE was calculated as pVO(2) (l/min) / log(10)peakVE (l/min). Correlation coefficients between the studied parameters were obtained. The prognosis of each variable adjusted for age was evaluated through Cox proportional hazard models and R2 percent (R2%) and V index (V6) were used as measures of the predictive accuracy of events of each of these variables. Receiver operating characteristic (ROC) curves from logistic regression models were used to determine the cut-offs for OUES and POUE. RESULTS: pVO(2): 20.5±5.9; percentage of predicted peak VO(2): 68.6±18.2; VE/VCO(2) slope: 30.6±8.3; OUES: 1.85±0.61; POUE: 0.88±0.27. During a mean follow-up of 33.1±14.8 months, 45 (21.8%) patients died, 10 (4.9%) underwent urgent heart transplantation and in three patients (1.5%) a left ventricular assist device was implanted. All variables proved to be independent predictors of this combined event; however, VE/VCO2 slope was most strongly associated with events (HR 11.14). In this population, POUE was associated with a higher risk of events than OUES (HR 9.61 vs. 7.01), and was also a better predictor of events (R2: 28.91 vs. 22.37). CONCLUSION: POUE was more strongly associated with death, urgent heart transplantation and implantation of a left ventricular assist device and proved to be a better predictor of events than OUES. These results suggest that this new parameter can increase the prognostic value of CPET in patients with CHF.

Failure of both azithromycin and antimony to treat cutaneous leishmaniasis in Manaus, AM, Brazil

A non-randomized controlled clinical trial was carried outin order to evaluate both azithromycin and antimony efficacy in cutaneous leishmaniasis in Manaus, AM, Brazil. Forty nine patients from both genders, aged 14 to 70, with cutaneous ulcers for less than three months and a positive imprint for Leishmania spp. amastigotes were recruited into two groups. Group I (26 patients) received a daily-single oral dose of 500 mg of azithromycin for 20 days and Group II (23 patients) received a daily-single intramuscular dose of 20 mg/kg of meglumine antimony, also for 20 days. Azithromycin cured three of 24 (12.5%) patients on days 60, 90 and 120 respectively whereas therapeutic failure was considered in 21 of 24 (87.5%) cases. In group II, antimony cured eight of 19 (42.1%) cases as follows: three on day 30, one each on day 60 and day 90, and three on day 120. Therapeutic failure occurred in 11 of 19 (57.9%) individuals. The efficacy of antimony for leishmaniasis was better than azithromycin but analysis for the intention-to-treat response rate did not show statistical difference between them. Although azithromycin was better tolerated, it showed a very low efficacy to treat cutaneous leishmaniasis in Manaus.

Mortality after Discharge from Intensive Care: the Impact of Organ System Failure and Nursing Workload Use at Discharge

OBJECTIVES: Mortality after ICU discharge accounts for approx. 20-30% of deaths. We examined whether post-ICU discharge mortality is associated with the presence and severity of organ dysfunction/failure just before ICU discharge. PATIENTS AND METHODS: The study used the database of the EURICUS-II study, with a total of 4,621 patients, including 2,958 discharged alive to the general wards (post-ICU mortality 8.6%). Over a 4-month period we collected clinical and demographic characteristics, including the Simplified Acute Physiology Score (SAPS II), Nine Equivalents of Nursing Manpower Use Score, and Sequential Organ Failure Assessment (SOFA) score. RESULTS: Those who died in the hospital after ICU discharge had a higher SAPS II score, were more frequently nonoperative, admitted from the ward, and had stayed longer in the ICU. Their degree of organ dysfunction/failure was higher (admission, maximum, and delta SOFA scores). They required more nursing workload resources while in the ICU. Both the amount of organ dysfunction/failure (especially cardiovascular, neurological, renal, and respiratory) and the amount of nursing workload that they required on the day before discharge were higher. The presence of residual CNS and renal dysfunction/failure were especially prognostic factors at ICU discharge. Multivariate analysis showed only predischarge organ dysfunction/failure to be important; thus the increased use of nursing workload resources before discharge probably reflects only the underlying organ dysfunction/failure. CONCLUSIONS: It is better to delay the discharge of a patient with organ dysfunction/failure from the ICU, unless adequate monitoring and therapeutic resources are available in the ward.

One Anastomosis Gastric Bypass versus Roux en Y Gastric Bypass as Salvage Technique after Failed Gastric Band: a Retrospective Analysis of 80 Cases

The classical “Roux en Y Gastric Bypass” (RYGBP) is still the standard technique between all the ones being used nowadays. The “One anastomosis gastric bypass” (OAGBP), is an evolution of the “Minigastic bypass” described by Robert Rutledge in 2001, is a well known and progressively frequent but still controversial technique. In our group, after an experience of 10 years using the RYGBP as a salvage surgery after failed gastric banding, in 132 cases, we decided to adopt the OAGBP as our preferential bariatric technique also in this situation. The theoretical main reasons for that shift are related to the increased safety, maximized weight loss, long term weight loss maintenance and reversibility of the operation. Method: Retrospectively we evaluated data of the surgical management of revisional cases for conversion, after failed or complicated gastric bands to gastric bypass. We selected the last 40 cases of each technique since May 2010. Results: All cases were performed by laparoscopy without any conversion. In both groups the conversion has been performed in one single step (17 cases, 42,5%). Data showed lower morbidity with OAGBP (2,5% against 7,5%) and better weight loss in theOAGBP cohort after a median follow up of 16months (67%against 55%) in patients revised after gastric band failure or complications. None had statistic significance (p>0,1) by the chi-square contingency table analysis.Conclusion: It seems to there is a difference in favour of OAGBP for conversion of complicated gastric bands. In this study we didn’t found statistic significance probably because of the short numbers. Prospective and more powerful studies are necessary to evaluate the benefit of the studied procedure.

Spatial analysis of suicide attack incidences in Kabul City

Dissertation submitted in partial fulfillment of the requirements for the Degree of Master of Science in Geospatial Technologies.

Strength and damage analysis of composite-aluminium adhesively-bonded single-lap joints

With the need to find an alternative way to mechanical and welding joints, and at the same time to overcome some limitations linked to these traditional techniques, adhesive bonds can be used. Adhesive bonding is a permanent joining process that uses an adhesive to bond the components of a structure. Composite materials reinforced with fibres are becoming increasingly popular in many applications as a result of a number of competitive advantages. In the manufacture of composite structures, although the fabrication techniques reduce to the minimum by means of advanced manufacturing techniques, the use of connections is still required due to the typical size limitations and design, technological and logistical aspects. Moreover, it is known that in many high performance structures, unions between composite materials with other light metals such as aluminium are required, for purposes of structural optimization. This work deals with the experimental and numerical study of single lap joints (SLJ), bonded with a brittle (Nagase Chemtex Denatite XNRH6823) and a ductile adhesive (Nagase Chemtex Denatite XNR6852). These are applied to hybrid joints between aluminium (AL6082-T651) and carbon fibre reinforced plastic (CFRP; Texipreg HS 160 RM) adherends in joints with different overlap lengths (LO) under a tensile loading. The Finite Element (FE) Method is used to perform detailed stress and damage analyses allowing to explain the joints’ behaviour and the use of cohesive zone models (CZM) enables predicting the joint strength and creating a simple and rapid design methodology. The use of numerical methods to simulate the behaviour of the joints can lead to savings of time and resources by optimizing the geometry and material parameters of the joints. The joints’ strength and failure modes were highly dependent on the adhesive, and this behaviour was successfully modelled numerically. Using a brittle adhesive resulted in a negligible maximum load (Pm) improvement with LO. The joints bonded with the ductile adhesive showed a nearly linear improvement of Pm with LO.

HIV-2 Integrase Polymorphisms and Longitudinal Genotypic Analysis of HIV-2 Infected Patients Failing a Raltegravir-Containing Regimen

To characterize the HIV-2 integrase gene polymorphisms and the pathways to resistance of HIV-2 patients failing a raltegravir-containing regimen, we studied 63 integrase strand transfer inhibitors (INSTI)-naïve patients, and 10 heavily pretreated patients exhibiting virological failure while receiving a salvage raltegravir-containing regimen. All patients were infected by HIV-2 group A. 61.4% of the integrase residues were conserved, including the catalytic motif residues. No INSTI-major resistance mutations were detected in the virus population from naïve patients, but two amino acids that are secondary resistance mutations to INSTIs in HIV-1 were observed. The 10 raltegravir-experienced patients exhibited resistance mutations via three main genetic pathways: N155H, Q148R, and eventually E92Q - T97A. The 155 pathway was preferentially used (7/10 patients). Other mutations associated to raltegravir resistance in HIV-1 were also observed in our HIV-2 population (V151I and D232N), along with several novel mutations previously unreported. Data retrieved from this study should help build a more robust HIV-2-specific algorithm for the genotypic interpretation of raltegravir resistance, and contribute to improve the clinical monitoring of HIV-2-infected patients.