Combination of pulsed corona discharge with TiO2 photocatalysis: verification of hypothesis

The oxidation potential of pulsed corona discharge concerning aqueous impurities is limited in respect to certain refractory compounds. This may be enhanced in combination of the discharge with catalysis/photocatalysis as developed in homogeneous gas-phase reactions. The objective of the work consists of testing the hypothesis of oxidation potential enhancement in combination of the discharge with TiO2 photocatalysis applied to aqueous solutions of refractory oxalate. Meglumine acridone acetate was included for meeting the practical needs. The experimental research was undertaken into oxidation of aqueous solutions under conditions of various target pollutant concentrations, pH and the pulse repetition rate with plain electrodes and the electrodes with TiO2 attached to their surface. The results showed no positive influence of the photocatalyst, the pollutants were oxidized with the rate identical within the accuracy of measurements. The possible explanation for the observed inefficiency may include low UV irradiance, screening effect of water and generally low oxidation rate in photocatalytic reactions. Further studies might include combination of electric discharge with ozone decomposition/radical formation catalysts.

Utilization of steelmaking waste materials for production of calcium carbonate (CaCO3)

The steel industry produces, besides steel, also solid mineral by-products or slags, while it emits large quantities of carbon dioxide (CO2). Slags consist of various silicates and oxides which are formed in chemical reactions between the iron ore and the fluxing agents during the high temperature processing at the steel plant. Currently, these materials are recycled in the ironmaking processes, used as aggregates in construction, or landfilled as waste. The utilization rate of the steel slags can be increased by selectively extracting components from the mineral matrix. As an example, aqueous solutions of ammonium salts such as ammonium acetate, chloride and nitrate extract calcium quite selectively already at ambient temperature and pressure conditions. After the residual solids have been separated from the solution, calcium carbonate can be precipitated by feeding a CO2 flow through the solution. Precipitated calcium carbonate (PCC) is used in different applications as a filler material. Its largest consumer is the papermaking industry, which utilizes PCC because it enhances the optical properties of paper at a relatively low cost. Traditionally, PCC is manufactured from limestone, which is first calcined to calcium oxide, then slaked with water to calcium hydroxide and finally carbonated to PCC. This process emits large amounts of CO2, mainly because of the energy-intensive calcination step. This thesis presents research work on the scale-up of the above-mentioned ammonium salt based calcium extraction and carbonation method, named Slag2PCC. Extending the scope of the earlier studies, it is now shown that the parameters which mainly affect the calcium utilization efficiency are the solid-to-liquid ratio of steel slag and the ammonium salt solvent solution during extraction, the mean diameter of the slag particles, and the slag composition, especially the fractions of total calcium, silicon, vanadium and iron as well as the fraction of free calcium oxide. Regarding extraction kinetics, slag particle size, solid-to-liquid ratio and molar concentration of the solvent solution have the largest effect on the reaction rate. Solvent solution concentrations above 1 mol/L NH4Cl cause leaching of other elements besides calcium. Some of these such as iron and manganese result in solution coloring, which can be disadvantageous for the quality of the PCC product. Based on chemical composition analysis of the produced PCC samples, however, the product quality is mainly similar as in commercial products. Increasing the novelty of the work, other important parameters related to assessment of the PCC quality, such as particle size distribution and crystal morphology are studied as well. As in traditional PCC precipitation process, the ratio of calcium and carbonate ions controls the particle shape; a higher value for [Ca2+]/[CO32-] prefers precipitation of calcite polymorph, while vaterite forms when carbon species are present in excess. The third main polymorph, aragonite, is only formed at elevated temperatures, above 40-50 °C. In general, longer precipitation times cause transformation of vaterite to calcite or aragonite, but also result in particle agglomeration. The chemical equilibrium of ammonium and calcium ions and dissolved ammonia controlling the solution pH affects the particle sizes, too. Initial pH of 12-13 during the carbonation favors nonagglomerated particles with a diameter of 1 μm and smaller, while pH values of 9-10 generate more agglomerates of 10-20 μm. As a part of the research work, these findings are implemented in demonstrationscale experimental process setups. For the first time, the Slag2PCC technology is tested in scale of ~70 liters instead of laboratory scale only. Additionally, design of a setup of several hundreds of liters is discussed. For these purposes various process units such as inclined settlers and filters for solids separation, pumps and stirrers for material transfer and mixing as well as gas feeding equipment are dimensioned and developed. Overall emissions reduction of the current industrial processes and good product quality as the main targets, based on the performed partial life cycle assessment (LCA), it is most beneficial to utilize low concentration ammonium salt solutions for the Slag2PCC process. In this manner the post-treatment of the products does not require extensive use of washing and drying equipment, otherwise increasing the CO2 emissions of the process. The low solvent concentration Slag2PCC process causes negative CO2 emissions; thus, it can be seen as a carbon capture and utilization (CCU) method, which actually reduces the anthropogenic CO2 emissions compared to the alternative of not using the technology. Even if the amount of steel slag is too small for any substantial mitigation of global warming, the process can have both financial and environmental significance for individual steel manufacturers as a means to reduce the amounts of emitted CO2 and landfilled steel slag. Alternatively, it is possible to introduce the carbon dioxide directly into the mixture of steel slag and ammonium salt solution. The process would generate a 60-75% pure calcium carbonate mixture, the remaining 25-40% consisting of the residual steel slag. This calcium-rich material could be re-used in ironmaking as a fluxing agent instead of natural limestone. Even though this process option would require less process equipment compared to the Slag2PCC process, it still needs further studies regarding the practical usefulness of the products. Nevertheless, compared to several other CO2 emission reduction methods studied around the world, the within this thesis developed and studied processes have the advantage of existing markets for the produced materials, thus giving also a financial incentive for applying the technology in practice.

Chemical derivatization of galactoglucomannan for functional materials

In the framework of the biorefinery concept researchers aspire to optimize the utilization of plant materials, such as agricultural wastes and wood. For most of the known processes, the first steps in the valorisation of biomass are the extraction and purification of the individual components. The obtained raw products by means of a controlled separation can consecutively be modified to result in biofuels or biogas for energy production, but also in value-added products such as additives and important building blocks for the chemical and material industries. Considerable efforts are undertaken in order to substitute the use of oil-based starting materials or at least minimize their processing for the production of everyday goods. Wood is one of the raw materials, which have gained large attention in the last decades and its composition has been studied in detail. Nowadays, the extraction of water-soluble hemicelluloses from wood is well known and so for example xylan can be obtained from hardwoods and O-acetyl galactoglucomannans (GGMs) from softwoods. The aim of this work was to develop water-soluble amphiphilic materials of GGM and to assess their potential use as additives. Furthermore, GGM was also applied as a crosslinker in the synthesis of functional hydrogels for the removal of toxic metals and metalloid ions from aqueous solutions. The distinguished products were obtained by several chemical approaches and analysed by nuclear magnetic resonance spectroscopy (NMR), Fourier transform infrared spectroscopy (FTIR), size exclusion chromatography (SEC), thermal gravimetric analysis (TGA), scanning electron microscope SEM, among others. Bio-based surfactants were produced by applying GGM and different fatty acids as starting materials. On one hand, GGM-grafted-fatty acids were prepared by esterification and on the other hand, well-defined GGM-block-fatty acid derivatives were obtained by linking amino-functional fatty acids to the reducing end of GGM. The reaction conditions for the syntheses were optimized and the resultant amphiphilic GGM derivatives were evaluated concerning their ability to reduce the surface tension of water as surfactants. Furthermore, the block-structured derivatives were tested in respect to their applicability as additives for the surface modification of cellulosic materials. Besides the GGM surfactants with a bio-based hydrophilic and a bio-based hydrophobic part, also GGM block-structured derivatives with a synthetic hydrophobic tail, consisting of a polydimethylsiloxane chain, were prepared and assessed for the hydrophobization of surface of nanofibrillated cellulose films. In order to generate GGM block-structured derivatives containing a synthetic tail with distinguished physical and chemical properties, as well as a tailored chain length, a controlled polymerization method was used. Therefore, firstly an initiator group was introduced at the reducing end of the GGM and consecutively single electron transfer-living radical polymerization (SET-LRP) was performed by applying three different monomers in individual reactions. For the accomplishment of the synthesis and the analysis of the products, challenges related to the solubility of the reactants had to be overcome. Overall, a synthesis route for the production of GGM block-copolymers bearing different synthetic polymer chains was developed and several derivatives were obtained. Moreover, GGM with different molar masses were, after modification, used as a crosslinker in the synthesis of functional hydrogels. Hereby, a cationic monomer was used during the free radical polymerization and the resultant hydrogels were successfully tested for the removal of chromium and arsenic ions from aqueous solutions. The hydrogel synthesis was tailored and materials with distinguished physical properties, such as the swelling rate, were obtained after purification. The results generated in this work underline the potential of bio-based products and the urge to continue carrying out research in order to be able to use more green chemicals for the manufacturing of biorenewable and biodegradable daily products.

Modified nano- and microcellulose based adsorption materials in water treatment

In recent decades, industrial activity growth and increasing water usage worldwide have led to the release of various pollutants, such as toxic heavy metals and nutrients, into the aquatic environment. Modified nanocellulose and microcellulose-based adsorption materials have the potential to remove these contaminants from aqueous solutions. The present research consisted of the preparation of five different nano/microcellulose-based adsorbents, their characterization, the study of adsorption kinetics and isotherms, the determination of adsorption mechanisms, and an evaluation of adsorbents’ regeneration properties. The same well known reactions and modification methods that were used for modifying conventional cellulose also worked for microfibrillated cellulose (MFC). The use of succinic anhydride modified mercerized nanocellulose, and aminosilane and hydroxyapatite modified nanostructured MFC for the removal of heavy metals from aqueous solutions exhibited promising results. Aminosilane, epoxy and hydroxyapatite modified MFC could be used as a promising alternative for H2S removal from aqueous solutions. In addition, new knowledge about the adsorption properties of carbonated hydroxyapatite modified MFC as multifunctional adsorbent for the removal of both cations and anions ions from water was obtained. The maghemite nanoparticles (Fe3O4) modified MFC was found to be a highly promising adsorbent for the removal of As(V) from aqueous solutions due to its magnetic properties, high surface area, and high adsorption capacity . The maximum removal efficiencies of each adsorbent were studied in batch mode. The results of adsorption kinetics indicated very fast removal rates for all the studied pollutants. Modeling of adsorption isotherms and adsorption kinetics using various theoretical models provided information about the adsorbent’s surface properties and the adsorption mechanisms. This knowledge is important for instance, in designing water treatment units/plants. Furthermore, the correspondence between the theory behind the model and properties of the adsorbent as well as adsorption mechanisms were also discussed. On the whole, both the experimental results and theoretical considerations supported the potential applicability of the studied nano/microcellulose-based adsorbents in water treatment applications.

Graphene from Graphite by Chemical and Physical Techniques.

Graphene is a material with extraordinary properties. Its mechanical and electrical properties are unparalleled but the difficulties in its production are hindering its breakthrough in on applications. Graphene is a two-dimensional material made entirely of carbon atoms and it is only a single atom thick. In this work, properties of graphene and graphene based materials are described, together with their common preparation techniques and related challenges. This Thesis concentrates on the topdown techniques, in which natural graphite is used as a precursor for the graphene production. Graphite consists of graphene sheets, which are stacked together tightly. In the top-down techniques various physical or chemical routes are used to overcome the forces keeping the graphene sheets together, and many of them are described in the Thesis. The most common chemical method is the oxidisation of graphite with strong oxidants, which creates a water-soluble graphene oxide. The properties of graphene oxide differ significantly from pristine graphene and, therefore, graphene oxide is often reduced to form materials collectively known as reduced graphene oxide. In the experimental part, the main focus is on the chemical and electrochemical reduction of graphene oxide. A novel chemical route using vanadium is introduced and compared to other common chemical graphene oxide reduction methods. A strong emphasis is placed on electrochemical reduction of graphene oxide in various solvents. Raman and infrared spectroscopy are both used in in situ spectroelectrochemistry to closely monitor the spectral changes during the reduction process. These in situ techniques allow the precise control over the reduction process and even small changes in the material can be detected. Graphene and few layer graphene were also prepared using a physical force to separate these materials from graphite. Special adsorbate molecules in aqueous solutions, together with sonic treatment, produce stable dispersions of graphene and few layer graphene sheets in water. This mechanical exfoliation method damages the graphene sheets considerable less than the chemical methods, although it suffers from a lower yield.

Differences in pressure and temperature transitions of proteins and polymer gels

Pressure-driven and temperature-driven transitions of two thermoresponsive polymers, poly(N-isopropylacrylamide) (pNIPAM) and poly(N-vinylisobutyramide) (pNVIBA)), in both a soluble linear polymer form and a cross-linked hydro-gel form, were examined by a dynamic light-scattering method and direct microscopic observation, respectively. Their behavior was compared with that of protein systems. Changes in some characteristic parameters in the time-intensity correlation functions of dynamic light-scattering measurement of aqueous solutions of pNIPAM at various pressures and temperatures showed no essential differences during temperature and pressure scanning and, as a whole, the motions of polymers in aqueous solutions were similar in two types of transitions until chain shrinkage occurred. The gels (cross-linked polymer gels) prepared from the thermoresponsive polymers also showed similar volume transitions responding to the pressure and temperature increase. In temperature transitions, however, gels showed drastic volume shrinkage with loss of transparency, while pressure-induced transition showed a slow recovery of transparency while keeping the size, after first transient drastic volume shrinkage with loss of transparency. At a temperature slightly higher than the transition under atmospheric temperature, so-called reentry of the volume change and recovery of the transparency were observed during the pressure-increasing process, which implies much smaller aggregation or non-aggregated collapsed polymer chains in the gel at higher pressures, indicating a certain mechanistic difference of the dehydration processes induced by temperature and pressure.

Electrophoretic analisys to detect and quantify additional whey in milk and dairy beverages

Polyacrylamide gel electrophoresis, SDS-PAGE system, was adjusted to detect the presence of additional whey in dairy beverages distributed in a Brazilian Government School Meals Program. Aqueous solutions of samples in 8 M urea were submitted to a polyacrylamide gel gradient (10% to 18%). Gel scans from electrophoresis patterns of previously adulterated milk samples showed that caseins peak areas decreased while peak areas of beta -lactoglobulin plus alpha -lactalbumin increased as the percentage of raw milk powder replaced by whey powder increased. The relative densitometer areas of caseins or beta -lactoglobulin plus alpha -lactalbumin plotted against the percentage of whey added to the raw milk showed a linear correlation coefficient square higher than 0.97. The caseins plot was used to determine the percentage of additional whey in 116 dairy beverages, chocolate or coffee flavor. Considering that the lowest relative caseins concentration found in commercial milk powder samples by the present method was 72%, the dairy beverages containing caseins percentages equal to or higher than this value were considered free of additional whey. Based on this criterion, about 49% of the coffee-flavor dairy beverages and 29% of the chocolate-flavor beverages, among all the samples analyzed were adulterated with whey protein to reach the total protein contents specified on their labels. The present method showed a sensitivity of 5% to additional whey.

The role of metal ions in selective and sustainable processes

Sustainability and recycling are core values in today’s industrial operations. New materials, products and processes need to be designed in such a way as to consume fewer of the diminishing resources we have available and to put as little strain on the environment as possible. An integral part of this is cleaning and recycling. New processes are to be designed to improve the efficiency in this aspect. Wastewater, including municipal wastewaters, is treated in several steps including chemical and mechanical cleaning of waters. Well-cleaned water can be recycled and reused. Clean water for everyone is one of the greatest challenges we are facing today. Ferric sulphate, made by oxidation from ferrous sulphate, is used in water purification. The oxidation of ferrous sulphate, FeSO4, to ferric sulphate in acidic aqueous solutions of H2SO4 over finely dispersed active carbon particles was studied in a vigorously stirred batch reactor. Molecular oxygen was used as the oxidation agent and several catalysts were screened: active carbon, active carbon impregnated with Pt, Rh, Pd and Ru. Both active carbon and noble metal-active carbon catalysts enhanced the oxidation rate considerably. The order of the noble metals according to the effect was: Pt >> Rh > Pd, Ru. By the use of catalysts, the production capacities of existing oxidation units can be considerably increased. Good coagulants have a high charge on a long polymer chain effectively capturing dirty particles of the opposite charge. Analysis of the reaction product indicated that it is possible to obtain polymeric iron-based products with good coagulation properties. Systematic kinetic experiments were carried out at the temperature and pressure ranges of 60B100°C and 4B10 bar, respectively. The results revealed that both non-catalytic and catalytic oxidation of Fe2+ to Fe3+ take place simultaneously. The experimental data were fitted to rate equations, which were based on a plausible reaction mechanism: adsorption of dissolved oxygen on active carbon, electron transfer from Fe2+ ions to adsorbed oxygen and formation of surface hydroxyls. A comparison of the Fe2+ concentrations predicted by the kinetic model with the experimentally observed concentrations indicated that the mechanistic rate equations were able to describe the intrinsic oxidation kinetics of Fe2+ over active carbon and active carbon-noble metal catalysts. Engineering aspects were closely considered and effort was directed to utilizing existing equipment in the production of the new coagulant. Ferrous sulphate can be catalytically oxidized to produce a novel long-chained polymeric iron-based flocculent in an easy and affordable way in existing facilities. The results can be used for modelling the reactors and for scale-up. Ferric iron (Fe3+) was successfully applied for the dissolution of sphalerite. Sphalerite contains indium, gallium and germanium, among others, and the application can promote their recovery. The understanding of the reduction process of ferric to ferrous iron can be used to develop further the understanding of the dissolution mechanisms and oxidation of ferrous sulphate. Indium, gallium and germanium face an ever-increasing demand in the electronics industry, among others. The supply is, however, very limited. The fact that most part of the material is obtained through secondary production means that real production quota depends on the primary material production. This also sets the pricing. The primary production material is in most cases zinc and aluminium. Recycling of scrap material and the utilization of industrial waste, containing indium, gallium and geranium, is a necessity without real options. As a part of this study plausible methods for the recovery of indium, gallium and germanium have been studied. The results were encouraging and provided information about the precipitation of these valuables from highly acidic solutions. Indium and gallium were separated from acidic sulphuric acid solutions by precipitation with basic sulphates such as alunite or they were precipitated as basic sulphates of their own as galliunite and indiunite. Germanium may precipitate as a basic sulphate of a mixed composition. The precipitation is rapid and the selectivity is good. When the solutions contain both indium and gallium then the results show that gallium should be separated before indium to achieve a better selectivity. Germanium was separated from highly acidic sulphuric acid solutions containing other metals as well by precipitating with tannic acid. This is a highly selective method. According to the study other commonly found metals in the solution do not affect germanium precipitation. The reduction of ferric iron to ferrous, the precipitation of indium, gallium and germanium, and the dissolution of the raw materials are strongly depending on temperature and pH. The temperature and pH effect were studied and which contributed to the understanding and design of the different process steps. Increased temperature and reduced pH improve the reduction rate. Finally, the gained understanding in the studied areas can be employed to develop better industrial processes not only on a large scale but also increasingly on a smaller scale. The small amounts of indium, gallium and germanium may favour smaller and more locally bound recovery.

Solute effects on the production and decay of primary species in the flash photolysis of indole

Maximum production rates ofs and decay kinetics for the hydrated electron, the indolyl neutral radical and the indole triplet state have been obtained in the microsecond, broadband (X > 260 nm) flash photolysis of helium-saturated, neutral aqueous solutions of indole, in the absence and in the presence of the solutes NaBr, BaCl2*2H20 and CdSCV Fluorescence spectra and fluorescence lifetimes have also been obtained in the absence and in the presence of the above solutes, The hydrated electron is produced monophotonically and biphotonically at an apparent maximum rate which is increased by BaCl2*2H20 and decreased by NaBr and CdSOif. The neutral indolyl radical may be produced monophotonically and biphotonically or strictly monophotonically at an apparent maximum rate which is increased by NaBr and CdSO^ and is unaffected by BaCl2*2H20. The indole triplet state is produced monophotonically at a maximum rate which is increased by all solutes. The hydrated electron decays by pseudo first order processes, the neutral indolyl radical decays by second order recombination and the indole triplet state decays by combined first and second order processes. Hydrated electrons are shown to react with H , H2O, indole, Na and Cd"*""1"". No evidence has been found for the reaction of hydrated electrons with Ba . The specific rate of second order neutral indolyl radical recombination is unaffected by NaBr and BaCl2*2H20, and is increased by CdSO^. Specific rates for both first and second order triplet state decay processes are increased by all solutes. While NaBr greatly reduced the fluorescence lifetime and emission band intensity, BaCl2*2H20 and CdSO^ had no effect on these parameters. It is suggested that in solute-free solutions and in those containing BaCl2*2H20 and CdSO^, direct excitation occurs to CTTS states as well as to first excited singlet states. It is further suggested that in solutions containing NaBr, direct excitation to first excited singlet states predominates. This difference serves to explain increased indole triplet state production (by ISC from CTTS states) and unchanged fluorescence lifetimes and emission band intensities in the presence of BaCl2*2H20 and CdSOt^., and increased indole triplet state production (by ISC from S^ states) and decreased fluorescence lifetime and emission band intensity in the presence of NaBr. Evidence is presented for (a) very rapid (tx ^ 1 us) processes involving reactions of the hydrated electron with Na and Cd which compete with the reformation of indole by hydrated electron-indole radical cation recombination, and (b) first and second order indole triplet decay processes involving the conversion of first excited triplet states to vibrationally excited ground singlet states.

Characterisation and optimisation of the flavour of health-promoting, plantderived bitterants in functional beverages.

Flavour is a combination of taste, odour, and chemesthetic sensations. Close associations exist between these sensory modalities, and thus, the overall flavour of a food or beverage product can change when the intensity of one or more of these sensations is altered. Strategies to modify flavour are often utilized by the food industry, and are central to the engineering of new and reformulated products. For functional food and beverages, flavour modification is particularly important, as fortifying agents can elicit high levels of less than desirable sensations, such as bitterness and astringency. The application of various flavour modifying strategies can decrease the perceived intensity of these sensations, and in tum, improve the sensory profile of the product. This collection of studies describes the sensory characteristics of experimental functional beverages fortified with trans-resveratrol, (+)-catechin, and/or caffeine, and examines the impact of novel flavour modifying strategies on the perceived flavour of these beverages. In the first study, results demonstrate that the flavour profile of Cabemet Sauvignon wines fortified with 20 mglL and 200 mg/L of trans-resveratrol is not perceived as different compared to control wine (0 mglL). However, Riesling wine fortified with 200 mg/L is perceived as significantly higher in bitterness compared to 20 mglL and control. For some functional food formulations, alternative strategies for flavour modification are needed. Traditional methods, such as the addition of sucrose and sodium chloride, may decrease the perceived 'healthiness' of a product, and thus, may be sub-optimal. In a second study, high and low concentrations of five different bitter inhibiting compounds - 'bitter blockers' - (B-cyclodextrin, homoeridictyol sodium salt, carboxymethylcellulose - low viscosity, zinc sulfate, magnesium sulfate) were tested for their efficacy towards decreasing the bitterness of high and low concentrations of caffeine and (+)catechin - two health-relevant, plant-derived bitterants. B-cyclodextrin and homoeridictyol sodium salt were the most effective blockers at decreasing (+ )-catechin and caffeine, respectively. In addition to bitter blockers, additional flavour modifying strategies, either alone or in combination - may also be successful in functional food formulations. Both sucrose and rebaudioside A - a plant-derived sweetener - were effective at decreasing the bitterness of (+)catechin. When added to (+)-catechin along with B-cyc1odextrin, both sweeteners provided the most effective decrease in bitterness compared to binary, ternary, or quaternary mixtures of (+)catechin together with bitter blockers, sweeteners, andlor odourants. The perceived intensity of sensations elicited by sweeteners and odourants was not affected by the addition of bitter blockers, and thus, their impact within these complex matrices is minimal. In addition, withinmodal (taste-taste) compared to cross-modal (taste-odour) sensory interactions were more effective at decreasing the bitterness of (+ )-catechin. Overall, results from these studies demonstrate that certain novel, alternative flavour modifying approaches may be successful towards lowering the bitterness and astringency elicited by (+ )-catechin and caffeine in aqueous solutions.

Polysaccharide-based Polyion Complex Micelles as New Delivery Systems for Hydrophilic Cationic Drugs

Les micelles polyioniques ont émergé comme des systèmes prometteurs de relargage de médicaments hydrophiles ioniques. Le but de cette étude était le développement des micelles polyioniques à base de dextrane pour la relargage de médicaments hydrophiles cationiques utilisant une nouvelle famille de copolymères bloc carboxymethyldextran-poly(éthylène glycol) (CMD-PEG). Quatre copolymères CMD-PEG ont été préparés dont deux copolymères identiques en termes de longueurs des blocs de CMD et de PEG mais différent en termes de densité de charges du bloc CMD; et deux autres copolymères dans lesquels les blocs chargés sont les mêmes mais dont les blocs de PEG sont différents. Les propriétés d’encapsulation des micelles CMD-PEG ont été évaluées avec différentes molécules cationiques: le diminazène (DIM), un médicament cationique modèle, le chlorhydrate de minocycline (MH), un analogue semi-synthétique de la tétracycline avec des propriétés neuro-protectives prometteuses et différents antibiotiques aminoglycosidiques. La cytotoxicité des copolymères CMD-PEG a été évaluée sur différentes lignées cellulaires en utilisant le test MTT et le test du Bleu Alamar. La formation de micelles des copolymères de CMD-PEG a été caractérisée par différentes techniques telles que la spectroscopie RMN 1H, la diffusion de la lumière dynamique (DLS) et la titration calorimétrique isotherme (ITC). Le taux de relargage des médicaments et l’activité pharmacologique des micelles contenant des médicaments ont aussi été évalués. Les copolymères CMD-PEG n'ont induit aucune cytotoxicité dans les hépatocytes humains et dans les cellules microgliales murines (N9) après 24 h incubation pour des concentrations allant jusqu’à 15 mg/mL. Les interactions électrostatiques entre les copolymères de CMD-PEG et les différentes drogues cationiques ont amorcé la formation de micelles polyioniques avec un coeur composé du complexe CMD-médicaments cationiques et une couronne composée de PEG. Les propriétés des micelles DIM/CMDPEG ont été fortement dépendantes du degré de carboxyméthylation du bloc CMD. Les micelles de CMD-PEG de degré de carboxyméthylation du bloc CMD ≥ 60 %, ont incorporé jusqu'à 64 % en poids de DIM et ont résisté à la désintégration induite par les sels et ceci jusqu'à 400 mM NaCl. Par contre, les micelles de CMD-PEG de degré de carboxyméthylation ~ 30% avaient une plus faible teneur en médicament (~ 40 % en poids de DIM) et se désagrégeaient à des concentrations en sel inférieures (∼ 100 mM NaCl). Le copolymère de CMD-PEG qui a montré les propriétés micellaires les plus satisfaisantes a été sélectionné comme système de livraison potentiel de chlorhydrate de minocycline (MH) et d’antibiotiques aminoglycosidiques. Les micelles CMD-PEG encapsulantes de MH ou d’aminoglycosides ont une petite taille (< 200 nm de diamètre), une forte capacité de chargement (≥ 50% en poids de médicaments) et une plus longue période de relargage de médicament. Ces micelles furent stables en solution aqueuse pendant un mois; après lyophilisation et en présence d'albumine sérique bovine. De plus, les micelles ont protégé MH contre sa dégradation en solutions aqueuses. Les micelles encapsulant les drogues ont maintenu les activités pharmacologiques de ces dernières. En outre, les micelles MH réduisent l’inflammation induite par les lipopolysaccharides dans les cellules microgliales murines (N9). Les micelles aminoglycosides ont été quant à elles capable de tuer une culture bactérienne test. Toutefois les micelles aminoglycosides/CMDPEG furent instables dans les conditions physiologiques. Les propriétés des micelles ont été considérablement améliorées par des modifications hydrophobiques de CMD-PEG. Ainsi, les micelles aminoglycosides/dodecyl-CMD-PEG ont montré une taille plus petite et une meilleure stabilité aux conditions physiologiques. Les résultats obtenus dans le cadre de cette étude montrent que CMD-PEG copolymères sont des systèmes prometteurs de relargage de médicaments cationiques.

Modification d'acides biliaires à l'aide de polymères pour en moduler les propriétés d'agrégation

Les polymères amphiphiles sont largement utilisés pour les applications biomédicales et pharmaceutiques. Afin d’améliorer les chances de biocompatibilité des nouveaux polymères que nous voulons développer, nous avons utilisé des composés naturels, les acides biliaires, comme produits de départ dans la synthèse de ces polymères. De nouveaux polymères anioniques amphiphiles dérivés de l’acide cholique ont été préparés par polymérisation radicalaire par transfert d’atomes. Par un contrôle rigoureux des conditions de polymérisation, des bras de poly(acide acrylique) de différentes longueurs ont été greffés sur le squelette de l’acide cholique. L’architecture moléculaire des polymères a été étudiée par spectroscopie 1H RMN et par spectrométrie de masse. Ces polymères en étoile formés par l’acide biliaire modifié sont capables de s’agréger dans l’eau même si les groupements hydroxyles ont été remplacés par des segments plus volumineux. Il a été observé que les liaisons ester entre le polymère et le cœur d’acide cholique sont sensibles à l’hydrolyse en solution aqueuse. Pour remédier au problème de stabilité en solution aqueuse et pour avoir, en même temps, des bras hydrophiles non ioniques et biocompatibles, de l’oxyde d’éthylène a été polymérisé sur l’acide cholique par polymérisation anionique. Les liaisons éther formées entre le polymère et les groupements hydroxyles de l’acide biliaire sont plus stables que les liaisons ester sur le polymère de poly(acide acrylique). Les conditions de réaction de la polymérisation anionique ont été optimisées et ont donné des polymères aux architectures et aux masses molaires contrôlées. Les nouveaux polymères forment des agrégats sphériques tel qu’observé par microscopie électronique à transmission avec des échantillons préparés par la méthode de fracture à froid. Leur morphologie est différente de celle des agrégats cylindriques formés par les acides biliaires. Avec la méthode optimisée pour la polymérisation anionique, l’éther d’allyle et glycidyle a été polymérisé sur un dérivé d’acide cholique, suivi par une thiolation des liaisons doubles pour introduire l’amine ou l’acide sur la chaîne polymère. Cette addition radicalaire est efficace à plus de 90%. Les polymères qui en résultent sont solubles dans l’eau et s’agrègent à une certaine concentration critique. Il est particulièrement intéressant d’observer la thermosensibilité des polymères ayant des groupements amine, laquelle peut être modulée en acétylant partiellement les amines, donnant des points nuages entre 15 et 48°C.

Semisynthetic aminoglycoside antibiotics : toward biomimetic synthesis, evasion of bacterial resistance and reduced toxicity

Les antibiotiques aminoglycosidiques sont des agents bactéricides de grande valeur et d’efficacité à large spectre contre les pathogènes Gram-positifs et Gram-négatifs, dont plusieurs membres naturels et semisynthétiques sont importants dans l’histoire clinique depuis 1950. Des travaux crystallographiques sur le ribosome, récompensés par le prix Nobel, ont démontré comment leurs diverses structures polyaminées sont adaptées pour cibler une hélice d’ARN dans le centre de codage de la sous-unité 30S du ribosome bactérien. Leur interférence avec l’affinité et la cinétique des étapes de sélection et vérification des tARN induit la synthèse de protéines à basse fidélité, et l’inhibition de la translocation, établissant un cercle vicieux d’accumulation d’antibiotique et de stress sur la membrane. En réponse à ces pressions, les pathogènes bactériens ont évolué et disséminé une panoplie de mécanismes de résistance enzymatiques et d’expulsion : tels que les N acétyltransférases, les O phosphotransférases et les O nucleotidyltransférases qui ciblent les groupements hydroxyle et amino sur le coeur des aminoglycosides; des méthyl-transférases, qui ciblent le site de liaison ribosomale; et des pompes d’expulsion actives pour l’élimination sélective des aminoglycosides, qui sont utilisés par les souches Gram-négatives. Les pathogènes les plus problématiques, qui présentent aujourd’hui une forte résilience envers la majorité des classes d’antibiotiques sur le bord de la pan-résistance ont été nommés des bactéries ESKAPE, une mnémonique pour Enterococcus faecium, Staphylococcus aureus, Klebsiella pneumoniae, Acinetobacter baumannii, Pseudomonas aeruginosa et Enterobacteriaceae. La distribution globale des souches avec des mécanismes de résistance envers les standards cliniques aminoglycosides, tels que la tobramycine, l’amikacine et la gentamicine, est comprise entre 20 et 60% des isolées cliniques. Ainsi, les aminoglycosides du type 4,6-disubstitués-2-deoxystreptamine sont inadéquats comme thérapies anti-infectieuses à large spectre. Cependant, la famille des aminoglycosides 4,5-disubstitués, incluant la butirosine, la neomycine et la paromomycine, dont la structure plus complexe, pourrait constituter une alternative. Des collègues dans le groupe Hanessian et collaborateurs d’Achaogen Inc. ont démontré que certains analogues de la paraomomycine et neomycine, modifiés par désoxygénation sur les positions 3’ et 4’, et par substitution avec la chaîne N1-α-hydroxy-γ-aminobutyramide (HABA) provenant de la butirosine, pourrait produire des antibiotiques très prometteurs. Le Chapitre 4 de cette dissertation présente la conception et le développement d’une stratégie semi-synthétique pour produire des nouveaux aminoglycosides améliorés du type 4,5 disubstitués, inspiré par des modifications biosynthétiques de la sisomicine, qui frustrent les mécanismes de résistance bactérienne distribuées globalement. Cette voie de synthèse dépend d’une réaction d’hydrogénolyse de type Tsuji catalysée par palladium, d’abord développée sur des modèles monosaccharides puis subséquemment appliquée pour générer un ensemble d’aminoglycosides hybrides entre la neomycine et la sisomicine. Les études structure-activité des divers analogues de cette nouvelle classe ont été évaluées sur une gamme de 26 souches bactériennes exprimant des mécanismes de résistance enzymatique et d’expulsion qui englobe l’ensemble des pathogènes ESKAPE. Deux des antibiotiques hybrides ont une couverture antibacterienne excellente, et cette étude a mis en évidence des candidats prometteurs pour le développement préclinique. La thérapie avec les antibiotiques aminoglycosidiques est toujours associée à une probabilité de complications néphrotoxiques. Le potentiel de toxicité de chaque aminoglycoside peut être largement corrélé avec le nombre de groupements amino et de désoxygénations. Une hypothèse de longue date dans le domaine indique que les interactions principales sont effectuées par des sels des groupements ammonium, donc l’ajustement des paramètres de pKa pourrait provoquer une dissociation plus rapide avec leurs cibles, une clairance plus efficace et globalement des analogues moins néphrotoxiques. Le Chapitre 5 de cette dissertation présente la conception et la synthèse asymétrique de chaînes N1 HABA β substitutées par mono- et bis-fluoration. Des chaînes qui possèdent des γ-N pKa dans l’intervalle entre 10 et 7.5 ont été appliquées sur une neomycine tétra-désoxygénée pour produire des antibiotiques avancés. Malgré la réduction considérable du γ N pKa, le large spectre bactéricide n’a pas été significativement affecté pour les analogues fluorés isosteriques. De plus, des études structure-toxicité évaluées avec une analyse d’apoptose propriétaire d’Achaogen ont démontré que la nouvelle chaîne β,β difluoro-N1-HABA est moins nocive sur un modèle de cellules de rein humain HK2 et elle est prometteuse pour le développement d’antibiotiques du type neomycine avec des propriétés thérapeutiques améliorées. Le chapitre final de cette dissertation présente la proposition et validation d’une synthèse biomimétique par assemblage spontané du aminoglycoside 66-40C, un dimère C2 symétrique bis-imine macrocyclique à 16 membres. La structure proposée du macrocycle a été affinée par spectroscopie nucléaire à un système trans,trans-bis-azadiène anti-parallèle. Des calculs indiquent que l’effet anomérique de la liaison α glycosidique entre les anneaux A et B fournit la pré-organisation pour le monomère 6’ aldéhydo sisomicine et favorise le produit macrocyclique observé. L’assemblage spontané dans l’eau a été étudié par la dimérisation de trois divers analogues et par des expériences d’entre croisement qui ont démontré la généralité et la stabilité du motif macrocyclique de l'aminoglycoside 66-40C.

Revêtement anti-apoptotique à base de chondroïtine sulfate : vers un stent-graft bioactif

La réparation endovasculaire (EVAR) est une technique minimalement invasive permettant de traiter l’anévrisme de l’aorte abdominale (AAA) par l’entremise d’un stent- graft (SG). L’utilisation d’EVAR est actuellement limitée par de fréquentes complications liées à une guérison inadéquate autour de l’implant. Ce manque de guérison est principalement dû au type de recouvrement polymérique des SG, au milieu pro-apoptotique des AAA et à l’accès réduit aux nutriments et à l’oxygène après EVAR. L’objectif de cette thèse consistait à concevoir un revêtement bioactif permettant d’inhiber l’apoptose et stimuler la croissance des cellules musculaires lisses vasculaires (CMLV), pour ainsi favoriser la guérison des tissus vasculaires autour des SG. La chondroïtine-4-sulfate (CS) a d’abord été choisie, car elle a été identifiée comme un médiateur important de la réparation vasculaire. Il a été démontré que la CS en solution influence directement la résistance à l’apoptose des CMLV, en plus de favoriser la différenciation myofibroblastique chez les fibroblastes. Dans le cadre de ce projet, un premier revêtement à base de CS et de collagène a été créé. Bien que le revêtement permettait d’induire une résistance à l’apoptose chez les CMLV, il se désintégrait trop rapidement dans des conditions aqueuses. Une nouvelle méthodologie a donc été adaptée afin de greffer la CS directement sur des surfaces aminées, à l’aide d’un système utilisant un carbodiimide. Dans le but d’accroître la croissance des CMLV à la surface des revêtements, le facteur de croissance de l’épiderme (EGF) a ensuite été sélectionné. En plus de ses propriétés mitogéniques et chimiotactiques, l’EGF stimule la production d’éléments de la matrice extracellulaire, comme le collagène et la fibronectine. De plus, l’activation du récepteur de l’EGF inhibe également l’apoptose des CMLV. L’EGF a donc été greffé sur la CS. Le revêtement de CS+EGF a démontré une bonne uniformité et bioactivité sur des surfaces de verre aminé. iii iv Dans une 3ème étape, afin de permettre de transposer ce revêtement bioactif sur des implants, plusieurs méthodes permettant de créer des groupements d’amines primaires sur les biomatériaux polymériques comme le PET ou le ePTFE ont été étudiées. La polymérisation par plasma a été choisie pour créer le revêtement CS+EGF à la surface de PET. Une fois de plus, celui-ci a permis d’inhiber l’apoptose des CMLV, dans des conditions pro-apoptotiques, et de favoriser la croissance des cellules. Le revêtement de CS et d’EGF, déposé sur des surfaces aminées, possède des caractéristiques biologiques intéressantes et semble donc prometteur pour favoriser une meilleure guérison autour des SG.

New stimuli-responsive block random copolymers and their aggregation

Les polymères sensibles à des stimuli ont été largement étudiés ces dernières années notamment en vue d’applications biomédicales. Ceux-ci ont la capacité de changer leurs propriétés de solubilité face à des variations de pH ou de température. Le but de cette thèse concerne la synthèse et l’étude de nouveaux diblocs composés de deux copolymères aléatoires. Les polymères ont été obtenus par polymérisation radicalaire contrôlée du type RAFT (reversible addition-fragmentation chain-transfer). Les polymères à bloc sont formés de monomères de méthacrylates et/ou d’acrylamides dont les polymères sont reconnus comme thermosensibles et sensible au pH. Premièrement, les copolymères à bloc aléatoires du type AnBm-b-ApBq ont été synthétisés à partir de N-n-propylacrylamide (nPA) et de N-ethylacrylamide (EA), respectivement A et B, par polymérisation RAFT. La cinétique de copolymérisation des poly(nPAx-co-EA1-x)-block-poly(nPAy-co-EA1-y) et leur composition ont été étudiées afin de caractériser et évaluer les propriétés physico-chimiques des copolymères à bloc aléatoires avec un faible indice de polydispersité . Leurs caractères thermosensibles ont été étudiés en solution aqueuse par spectroscopie UV-Vis, turbidimétrie et analyse de la diffusion dynamique de la lumière (DLS). Les points de trouble (CP) observés des blocs individuels et des copolymères formés démontrent des phases de transitions bien définies lors de la chauffe. Un grand nombre de macromolécules naturels démontrent des réponses aux stimuli externes tels que le pH et la température. Aussi, un troisième monomère, 2-diethylaminoethyl methacrylate (DEAEMA), a été ajouté à la synthèse pour former des copolymères à bloc , sous la forme AnBm-b-ApCq , et qui offre une double réponse (pH et température), modulable en solution. Ce type de polymère, aux multiples stimuli, de la forme poly(nPAx-co-DEAEMA1-x)-block-poly(nPAy-co-EA1-y), a lui aussi été synthétisé par polymérisation RAFT. Les résultats indiquent des copolymères à bloc aléatoires aux propriétés physico-chimiques différentes des premiers diblocs, notamment leur solubilité face aux variations de pH et de température. Enfin, le changement d’hydrophobie des copolymères a été étudié en faisant varier la longueur des séquences des blocs. Il est reconnu que la longueur relative des blocs affecte les mécanismes d’agrégation d’un copolymère amphiphile. Ainsi avec différents stimuli de pH et/ou de température, les expériences effectuées sur des copolymères à blocaléatoires de différentes longueurs montrent des comportements d’agrégation intéressants, évoluant sous différentes formes micellaires, d’agrégats et de vésicules.