The wire rope & its applications,

Mode of access: Internet.

The theory, practice, and architecture of bridges of stone, iron, timber, and wire;

Mode of access: Internet.

Iron and steel wire; a bibliography,

Mode of access: Internet.

NOAA weather wire service (NWWS).

"NOAA Weather Wire Service is part of National Disaster Warning Communication System (NADWARN)."

Proceedings of the convention of the Wood, Wire and Metal Lathers' International Union.

Mode of access: Internet.

Double-heater-wire circuits and heat-and-moisture exchangers and the risk of ventilator-associated pneumonia

Objective: To compare the incidence of ventilator-associated pneumonia (VAP) in patients ventilated in intensive care by means of circuits humidified with a hygroscopic heat-and-moisture exchanger with a bacterial viral filter (HME) or hot-water humidification with a heater wire in both inspiratory and expiratory circuit limbs (DHW) or the inspiratory limb only (SHW). Design: A prospective, randomized trial. Setting: A metropolitan teaching hospital's general intensive care unit. Patients: Three hundred eighty-one patients requiring a minimum period of mechanical ventilation of 48 hrs. Interventions: Patients were randomized to humidification with use of an HME (n = 190), SHW (n = 94), or DHW (n = 97). Measurements and Main Results. Study end points were VAP diagnosed on the basis of Clinical Pulmonary Infection Score (CPIS) (1), HME resistance after 24 hrs of use, endotracheal tube resistance, and HME use per patient. VAP occurred with similar frequency in all groups (13%, HME; 14%, DHW; 10%, SHW; p = 0.61) and was predicted only by current smoking (adjusted odds ratio [AOR], 2.1; 95% confidence interval [CI], 1.1-3.9; p =.03) and ventilation days (AOR, 1.05; 95% Cl, 1.0-1.2; p =.001); VAP was less likely for patients with an admission diagnosis of pneumonia (AOR, 0.40; 95% Cl, 0.4-0.2; p =.04). HME resistance after 24 hrs of use measured at a gas flow of 50 L/min was 0.9 cm H2O (0.4-2.9). Endotracheal tube resistance was similar for all three groups (16-19 cm H2O min/L; p =.2), as were suction frequency, secretion thickness, and blood on suctioning (p =.32, p =.06, and p =.34, respectively). The HME use per patient per day was 1.13. Conclusions: Humidification technique does not influence either VAP incidence or secretion characteristics, but HMEs may have air-flow resistance higher than manufacturer specifications after 24 hrs of use.

ESTUDO COMPARATIVO DA POSIÇÃO ÂNTERO POSTERIOR DOS PRIMEIROS MOLARES INFERIORES NO TRATAMENTO ORTODÔNTICO, UTILIZANDO AS TÉCNICAS STRAIGHT-WIRE E EDGEWISE, EM CASOS DE MÁ OCLUSÃO DE CLASSE I DE ANGLE, COM EXTRAÇÃO DE PRIMEIROS PRÉ-MOLARES

Este estudo avaliou o posicionamento ântero posterior dos primeiros molares inferiores, durante o tratamento ortodôntico, utilizando o arco lingual inferior como acessório de ancoragem na técnica Straight-Wire, em comparação aos casos tratados pela técnica Edgewise, sem a utilização do arco lingual. Dois grupos foram selecionados, ambos apresentando má oclusão de Classe I de Angle7, tratados com extração dos primeiros pré-molares superiores e inferiores. Foi utilizada uma amostra de 255 telerradiografias em norma lateral, obtidas de pacientes brasileiros, de ambos os sexos, com média de idade de 13 anos e 6 meses e com diferentes padrões de crescimento facial. Embasado na análise e discussão dos resultados, concluiu-se que: 1) do início do tratamento ao fim da fase de nivelamento, a perda de ancoragem coronária do primeiro molar inferior foi maior nos casos tratados com a técnica Straight-Wire; 2) do fim da fase de nivelamento ao fim do tratamento, a perda de ancoragem coronária e radicular do primeiro molar inferior foi maior na técnica Edgewise; 3) do início ao fim tratamento a perda de ancoragem radicular foi maior nos pacientes tratados com a técnica Edgewise; e 4) o deslocamento ântero-posterior dos incisivos inferiores não apresentou diferença estatisticamente significante para ambas as técnicas, em todas as etapas observadas.(AU)

Avaliação das inclinações dentárias obtidas pela técnica Straight-Wire Prescrição Capelozza Classe II.

Ao criar a técnica para tratamento ortodôntico denominado Straight-Wire, Andrews introduziu o uso de bráquetes pré-programados, ou bráquetes construídos individualmente para cada dente, com o objetivo de melhor posicioná-los ao final do tratamento. Capelozza Filho sugeriu novas angulações e inclinações para dentes que necessitavam de ajuste ao final do tratamento, criando prescrições para os diferentes padrões faciais. O presente trabalho tem por objetivo avaliar as alterações nas inclinações dentárias causadas pelo tratamento ortodôntico nos dentes anteriores utilizando-se da prescrição Capelozza Classe II. Foram selecionados 17 indivíduos adultos de padrão facial II, portadores de má-oclusão Classe II; para tratamento ortodôntico compensatório, e em três tempos clínicos, relativos a três diferentes fios ortodônticos (.020 ; .019 x .025 , .021 x .025 ), foram realizados exames de tomografia computadorizada volumétrica, para mensuração e posterior avaliação das inclinações dentárias alcançadas em cada um dos tempos, pela ação de cada um dos fios, comparando-se estes valores aos da prescrição utilizada, bem como das diferenças ocorridas entre os tempos. Após a coleta de dados e aplicação dos testes estatísticos, concluiu-se que existe diferença estatística (p<0,05) na maioria dos valores da prescrição e os valores encontrados em cada um dos tempos avaliados; não foram encontradas diferenças estatisticamente significantes quando comparados os tempos estudados. Observou-se também uma tendência dos dentes a expressarem a prescrição apenas em T3.

An investigation of the mechanics of wire drawing with the superposition of an oscillatory drawing stress

A number of investigators have studied the application of oscillatory energy to a metal undergoing plastic deformation. Their results have shown that oscillatory stresses reduce both the stress required to initiate plastic deformation and the friction forces between the tool and workpiece. The first two sections in this thesis discuss historically and technically the devolopment of the use of oscillatory energy techniques to aid metal forming with particular reference to wire drawing. The remainder of the thesis discusses the research undertaken to study the effect of applying longitudinal oscillations to wire drawing. Oscillations were supplied from an electric hydraulic vibrator at frequencies in the range 25 to 500 c/s., and drawing tests were performed at drawing speeds up to 50 ft/m. on a 2000 lbf. bull-block. Equipment was designed to measure the drawing force, drawing torque, amplitude of die and drum oscillation and drawing speed. Reasons are given for selecting mild steel, pure and hard aluminium, stainless steel and hard copper as the materials to be drawn, and the experimental procedure and calibration of measuring equipment arc described. Results show that when oscillatory stresses are applied at frequencies within the range investigated : (a) There is no reduction in the maximum drawing load. (b) Using sodium stearate lubricant there is a negligible reduction in the coefficient of friction between the die and wire. (c) Pure aluminium does not absorb sufficient oscillatory energy to ease the movement of dislocations. (d) Hard aluminium is not softened by oscillatory energy accelerating the diffusion process. (e) Hard copper is not cyclically softened. A vibration analysis of the bull-block and wire showed that oscillatory drawiing in this frequency range, is a mechanical process of straining; and unstraining the drawn wire, and is dependent upon the stiffness of the material being drawn and the drawing machine. Directions which further work should take are suggested.

Lubrication efficiency and die design in wire drawing

With the competitive challenge facing business today, the need to keep cost down and quality up is a matter of survival. One way in which wire manufacturers can meet this challenge is to possess a thorough understanding of deformation, friction and lubrication during the wire drawing process, and therefore to make good decisions regarding the selection and application of lubricants as well as the die design. Friction, lubrication and die design during wire drawing thus become the subject of this study. Although theoretical and experimental investigations have been being carried out ever since the establishment of wire drawing technology, many problems remain unsolved. It is therefore necessary to conduct further research on traditional and fundamental subjects such as the mechanics of deformation, friction, lubrication and die design in wire drawing. Drawing experiments were carried out on an existing bull-block under different cross-sectional area reductions, different speeds and different lubricants. The instrumentation to measure drawing load and drawing speed was set up and connected to the wire drawing machine, together with a data acquisition system. A die box connected to the existing die holder for using dry soap lubricant was designed and tested. The experimental results in terms of drawing stress vs percentage area reduction curves under different drawing conditions were analysed and compared. The effects on drawing stress of friction, lubrication, drawing speed and pressure die nozzle are discussed. In order to determine the flow stress of the material during deformation, tensile tests were performed on an Instron universal test machine, using the wires drawn under different area reductions. A polynomial function is used to correlate the flow stress of the material with the plastic strain, on which a general computer program has been written to find out the coefficients of the stress-strain function. The residual lubricant film on the steel wire after drawing was examined both radially and longitudinally using an SEM and optical microscope. The lubricant film on the drawn wire was clearly observed. Therefore, the micro-analysis by SEM provides a way of friction and lubrication assessment in wire drawing.

Quantum wire hybridized with a single-level impurity

We have studied low-temperature properties of interacting electrons in a one-dimensional quantum wire (Luttinger liquid) side-hybridized with a single-level impurity. The hybridization induces a backscattering of electrons in the wire which strongly affects its low-energy properties. Using a one-loop renormalization group approach valid for a weak electron-electron interaction, we have calculated a transmission coefficient through the wire, T(epsilon), and a local density of states, nu(epsilon) at low energies epsilon. In particular, we have found that the antiresonance in T(epsilon) has a generalized Breit-Wigner shape with the effective width Gamma(epsilon) which diverges at the Fermi level.

In situ diagnostics and prognostics of wire bonding faults in IGBT modules for electric vehicle drives

This paper presents a diagnostic and prognostic condition monitoring method for insulated-gate bipolar transistor (IGBT) power modules for use primarily in electric vehicle applications. The wire-bond-related failure, one of the most commonly observed packaging failures, is investigated by analytical and experimental methods using the on-state voltage drop as a failure indicator. A sophisticated test bench is developed to generate and apply the required current/power pulses to the device under test. The proposed method is capable of detecting small changes in the failure indicators of the IGBTs and freewheeling diodes and its effectiveness is validated experimentally. The novelty of the work lies in the accurate online testing capacity for diagnostics and prognostics of the power module with a focus on the wire bonding faults, by injecting external currents into the power unit during the idle time. Test results show that the IGBT may sustain a loss of half the bond wires before the impending fault becomes catastrophic. The measurement circuitry can be embedded in the IGBT drive circuits and the measurements can be performed in situ when the electric vehicle stops in stop-and-go, red light traffic conditions, or during routine servicing.