Ultrafast optical Kerr effect in amorphous Ge10As40S30Se20 film induced by ultrashort laser pulses

The results of the femtosecond optical heterodyne detection of optical Kerr effect at 805 am with the 80 fs ultrafast pulses in amorphous Ge10As40S30Se20 film is reported in this Letter. The film shows an optical nonlinear response of 200 fs under ultrafast 80 fs-pulse excitation, and the values of real and imaginary parts of nonlinear susceptibility chi((3)) were 9.0 x 10(-12) esu and -4.0 x 10(-12) esu respectively. The large third-order nonlinearity and ultrafast response are attributed to the ultrafast distortion of the electron orbits surrounding the average positions of the nucleus of Ge, As, S and Se atoms. This Ge10As40S30Se20 chalcogenide glass would be expected as a promising material for optical switching technique.

Effect of bismuth oxide on the thermal stability and Judd-Ofelt parameters of Er 3(+)/Yb3(+) co-doped aluminophosphate glasses

The Er3+/Yb3+ co-doped glasses with compositions of xBi(2)O(3)-(65-x)P2O5-4Yb(2)O(3)-11Al(2)O(3)-5BaO-15Na(2)O (where x = 0, 2.5, 5, 7.5 and 10 mol%) were prepared using the normal melt quench technique. The optical absorption spectra of the glasses were recorded in the wavelength range 300-1700 nm. The effect of Bi2O3 content on the thermal stability and absorption spectra of glasses was investigated. In addition, the Judd-Ofelt parameters and oscillator strengths were calculated by employing Judd-Ofelt theory. It was observed that the positions of the fundamental absorption edge and cut-off wavelength shifted towards red as the content of Bi2O3 increased. However, there were no red shifts found both in the peak wavelength and in the center of mass wavelength of all absorption bands with Bi2O3 content increasing. The results of Judd-Ofelt theory analysis showed that Judd-Ofelt parameters Omega(t), (t = 2, 4, 6) changed sharply when Bi2O3 concentration exceeded 5 mol%. The variation trends of experimental oscillator strength were similar with those of Judd-Ofelt parameters as function of Bi2O3 concentrations. Moreover, differential scanning calorimetry experiments showed that the increases of Bi2O3 content weakened the network structure and then lowered the thermal stability of the glasses. The spontaneous emission probability A(rad), branching ratio beta and the radiative lifetime tau(rad) were also calculated and analyzed. The stimulated emission cross-section of Er3+ was calculated according to the McCumber theory. It was found that the stimulated emission cross-section of Er3+ was monotonically increases with Bi2O3 content increasing. (C) 2006 Elsevier B.V. All rights reserved.

Efficient laser oscillation of Yb : Y3Al5O12 single crystal grown by temperature gradient technique

Low-threshold and highly efficient continuous-wave laser performance of Yb:Y3Al5O12 (Yb:YAG) single crystal grown by a temperature gradient technique (TGT) was achieved at room temperature. The laser can be operated at 1030 and 1049 nm by varying the transmission of the output coupler. Slope efficiencies of 57% and 68% at 1049 and 1030 nm, respectively, were achieved for 10 at. % Yb:YAG sample in continuous-wave laser-diode pumping. The effect of pump power on the laser emission spectrum of both wavelengths is addressed. The near-diffraction-limited beam quality for different laser cavities was achieved. The excellent laser performance indicates that TGT-grown Yb:YAG crystals have very good optical quality and can be potentially used in high-power solid-state lasers.

Effect of annealing and gamma irradiation on undoped and Eu3+-doped Y2SiO5 single crystals

The absorption spectra of the undoped Y2SiO5 and Eu3+-doped Y2SiO5 crystals grown by the Czochralski technique were compared before and after annealing and, similarly, the unannealed and annealed crystals after gamma-ray irradiation. The absorption bands of Eu2+ ions with peaks at 300 and 390 nm were observed in the as-grown Y2SiO5:Eu3+ crystal. These peaks were more intense in H-2-annealed and irradiated Y2SiO5:Eu3+ crystals. The additional absorption peaks at 260 and 320-330 nm which were attributed to F color centers and O- hole centers were observed in irradiated undoped Y2SiO5 and Y2SiO5:Eu3+ crystals, respectively. (c) 2005 Elsevier B.V. All rights reserved.

A preliminary investigation of Elastomer Visible Implant (EVI)tag retention rates and the effect of tagging on the growth and survival of barbel (Barbus barbus L.).

The Elastomer Visible Implant system (EVI) is a relatively new technique for batch marking fish. The aim of this study was to assess retention rates and the possible effects of tagging on the growth and mortality of barbel, Barbus barbus, (81-197mm, fork length) over approximately 2 months using a syringe injection system.

Trends in development in the prawn fishing technique in India: a review

The paper provides some background information about the developments in the prawn fishing technique. The important indigenous gear for prawns are the filtering type nets like the stake nets, boat seines and beach seines with bag. The only indigenous net, which can be compared in design with the modern bottom trawling gear, is the "Thuri Valai" of the Madras Coast. Prawns have also been reported from the catches of gill nets and cast nets. Dredges and beam trawls are simplest among the dragged gear. Even though several earlier attempts were made with the beam trawl, in 1959 season a detailed experiment was made to study the fishing features of this gear. The subsequent experiments conducted were for comparison with otter trawl, towing of 2 beam trawls one behind the other and the use of tickler chain. The initial experiments with otter trawls were mainly directed towards operational aspects. The experiments were to evaluate the effectiveness of fully mechanised and partially mechanised operation, the effect of extra buoyancy of floats and the use of tickler chain. Subsequent developments had been on the structure and design of prawn trawling gear. Effect of long wings and sweeps were tested. Catches of nylon and cotton nets were compared. The sizes of meshes of the cod-end have also been increased.

The effect of dopants on the twist elastic constant and the rotational viscosity coefficient for nematics

The twist elastic constant, K2, and the rotational viscosity coefficient, γ1, are of importance when the response lime for the in-plane switching mode is studied. Since adding dopants is one technique to improve the response characteristics, the effect of dopants on these physical properties is significant. The effect on K2 and γ1 of adding alkyl(alkoxy) phenylcyclopentenones and alkyl(alkoxy) cyanobiphenyls to the base mixture ZLI-4792 together with their temperature dependence have been investigated using different temperature scales. The reduced temperature scale showed the effect of these dopants on K2 is small. On the other hand, the temperature dependence of γ1 depends on both the absolute temperature scale and the reduced temperature scale. Therefore, it is clear that the choice of temperature scale with which to compare γ1 for different systems raises fundamental questions which way not have a unique answer. 2000 OPA (Overseas Publishers Association) N.V. Published by license under the Gordon and Breach Science Publishers imprint.

Effect of salinity and food ration level on the growth of Nile tilapia (Oreochromis niloticus L.)

The effect of salinity (0, 10 & 20‰, water temperature 28 ± 1°C) and food ration (3 and 4.5% bw/day) on food consumption and growth of Nile tilapia, Oreochromis niloticus (10.77 ± 0.21g) were investigated. Individual food consumption was measured using X-radiography technique. Salinities (0, 10 & 20‰) did not have significant effect on the growth rate of groups of Nile tilapia fed at different ration levels (3 & 4.5% bw/day). This study showed that the growth of all-male fish was significantly better than all-female fish for all three salinities and two rations. Salinities from 0 to 20‰ had no effect on growth performance of males or female fish. In the present study, it was evident that fish fed at 3% bw/day ration ate all the food offered and fish fed at 4.5% bw/day did not consumed all amounts. Also, growth performance did not significantly differ among fish fed at 3% bw/day ration level and reared at different salinities. Fish reared under higher salinities (20‰) and fed at higher ration (4.5% bw/day) level had skin lesions and injuries on their body. It was assumed that fish fed at higher ration under higher salinities (20‰) and maintained higher osmoregulatory costs together with osmotic stress may have a negative influence on the appetite of fish. Another possibility that may have affected the appetite could be the unionized ammonia levels that were high. The high-unionized ammonia levels combined with the osmotic stress may have been the cause, or have aided, development of skin lesions and injuries on the fish at higher salinities.

Coupling between elytra of some beetles: Mechanism, forces and effect of surface texture

Lightweight materials, structures and coupling mechanisms are very important for realizing advanced flight vehicles. Here, we obtained the geometric structures and morphologies of the elytra of beetles and ascertained its coupling zone by using the histological section technique and SEM. We set up a three-dimensional motion observing system to monitor the opening and closing behaviour of elytra in beetles and to determine the motion mechanism. We constructed a force measuring system to measure the coupling forces between elytra. The results show that elytra open and close by rotating about a single axle, where the coupling forces may be as high as 160 times its own bodyweight, the elytra coupling with the tenon and mortise mechanism, surface texture and opening angle between elytra heavily influence the coupling forces. These results may provide insights into the design mechanism and structure for future vehicles of flight.

Effect of antibiotics on development in vitro of hamster pronucleate ova

Antibiotics are commonly added to embryo culture media, but effects on embryo development have not been examined thoroughly. Hamster ova were used to investigate whether penicillin, streptomycin or gentamicin affect embryo development in vitro. Ova were collected 10 h post activation by spermatozoa in vivo and cultured in five treatments: 1) Control: chemically-defined medium HECM-9 with no antibiotics; 2) HECM-9 with 100 IU/mL, penicillin; 3) HECM-9 with 50 mug/mL streptomycin; 4) HECM-9 with 10 mug/mL,gentamicin and 5) HECM-9 with both 100 IU/mL penicillin and 50 mug/mL streptomycin. Individually, penicillin, streptomycin and gentamicin did not affect embryo development to the 8-cell stage at 58 h post oocyte activation, or morula/blastocyst stages, or blastocysts alone at 82 h post activation. However, when penicillin and streptomycin were both present in the culture medium the percentages of 8-cell embryos at 58 h and blastocysts at 82 h were significantly lower than the control. No antibiotic treatment improved hamster embryo development in vitro. We caution against the use of penicillin and streptomycin together for hamster embryo culture, and show that it is not necessary to include any antibiotics in embryo culture media for up to 72 h if proper sterile technique is used with an oil overlay. (C) 2000 by Elsevier Science Inc.

Techniques to improve the shear strength of impacted bone graft: The effect of particle size and washing of the graft

Background: When fresh morselized graft is compacted, as in impaction bone-grafting for revision hip surgery, fat and marrow fluid is either exuded or trapped in the voids between particles. We hypothesized that the presence of incompressible fluid damps and resists compressive forces during impaction and prevents the graft particles from moving into a closer formation, thus reducing the graft strength. In addition, viscous fluid such as fat may act as an interparticle lubricant, thus reducing the interlocking of the particles. Methods: We performed mechanical shear testing in the laboratory with use of fresh-frozen human femoral-head allografts that had been passed through different orthopaedic bone mills to produce graft of differing particle-size distributions (grading). Results: After compaction of fresh graft, fat and marrow fluid continued to escape on application of normal loads. Washed graft, however, had little lubricating fluid and better contact between the particles, increasing the shear resistance. On mechanical testing, washed graft was significantly (p < 0.001) more resistant to shearing forces than fresh graft was. This feature was consistent for different bone mills that produced graft of different particle-size distributions and shear strengths. Conclusions: Removal of fat and marrow fluid from milled human allograft by washing the graft allows the production of stronger compacted graft that is more resistant to shear, which is the usual mode of failure. Further research into the optimum grading of particle sizes from bone mills is required. Clinical Relevance: Understanding the mechanical properties of milled human allograft is important when impaction grafting is used for mechanical support. A simple means of improving the mechanical strength of graft produced by currently available bone mills, including an intraoperative washing technique, is described.

Effect of microbial activities on the mobility of copper in stabilised contaminated soil

Stabilisation, using a wide range of binders including wastes, is most effective for heavy metal soil contamination. Bioremediation techniques, including bioaugmentation to enhance soil microbial population, are most effective for organic contaminants in the soil. For mixed contaminant scenarios a combination of these two techniques is currently being investigated. An essential issue in this combined remediation system is the effect of microbial processes on the leachability of the heavy metals. This paper considers the use of zeolite and compost as binder additives combined with bioaugmentation treatments and their effect on copper leachability in a model contaminated soil. Different leaching test conditions are considered including both NRA and TCLP batch leaching tests as well as flow-through column tests. Two flow rates are applied in the flow-through tests and the two leaching tests are compared. Recommendations are given as to the effectiveness of this combined remediation technique in the immobilisation of copper. © 2005 Taylor & Francis Group.

Airfoil flow and noise computation using monotonically integrated large eddy simulation and acoustic analogy: Effect of the grid resolution.

A new scalable Monotonically Integrated Large Eddy Simulation (MILES) method based on the Compact Accurately Boundary-Adjusting high-REsolution Technique (CABARET) has been applied for the simulation of unsteady flow around NACA0012 airfoil at Re = 400,000 and M = 0.058. The flow solution is coupled with the Ffowcs Williams-Hawkings formulation for far-field noise prediction. The computational modeling results are presented for several computational grid resolutions: 8, 16, and 32 million grid cells and compared with the experimental data available.

The effect of shear strength on the ballistic response of laminated composite plates

The ballistic performance of clamped circular carbon fibre reinforced polymer (CFRP) and Ultra High Molecular Weight Polyethylene (UHMWPE) fibre composite plates of equal areal mass and 0/90 lay-up were measured and compared with that of monolithic 304 stainless steel plates. The effect of matrix shear strength upon the dynamic response was explored by testing: (i) CFRP plates with both a cured and uncured matrix and (ii) UHMWPE laminates with identical fibres but with two matrices of different shear strength. The response of these plates when subjected to mid-span, normal impact by a steel ball was measured via a dynamic high speed shadow moiré technique. Travelling hinges emanate from the impact location and travel towards the supports. The anisotropic nature of the composite plate results in the hinges travelling fastest along the fibre directions and this results in square-shaped moiré fringes in the 0/90 plates. Projectile penetration of the UHMWPE and the uncured CFRP plates occurs in a progressive manner, such that the number of failed plies increases with increasing velocity. The cured CFRP plate, of high matrix shear strength, fails by cone-crack formation at low velocities, and at higher velocities by a combination of cone-crack formation and communition of plies beneath the projectile. On an equal areal mass basis, the low shear strength UHMWPE plate has the highest ballistic limit followed by the high matrix shear strength UHMWPE plate, the uncured CFRP, the steel plate and finally the cured CFRP plate. We demonstrate that the high shear strength UHMWPE plate exhibits Cunniff-type ballistic limit scaling. However, the observed Cunniff velocity is significantly lower than that estimated from the laminate properties. The data presented here reveals that the Cunniff velocity is limited in its ability to characterise the ballistic performance of fibre composite plates as this velocity is independent of the shear properties of the composites: the ballistic limit of fibre composite plates increases with decreasing matrix shear strength for both CFRP and UHMWPE plates. © 2013 Elsevier Masson SAS. All rights reserved.

Implementation of shading effect for reconstruction of smooth layerbased 3D holographic images

A holographic rendering algorithm using a layer-based structure with angular tiling supports view-dependent shading and accommodation cues. This approach also has the advantages of rapid computation speed and visual reduction of layer gap artefacts compared to other approaches. Holograms rendered with this algorithm are displayed using an SLM to demonstrate view-dependent shading and occlusion. © 2013 SPIE-IS&T.