Fault detection, diagnosis and active fault tolerant control for a satellite attitude control system

Modern control systems are becoming more and more complex and control algorithms more and more sophisticated. Consequently, Fault Detection and Diagnosis (FDD) and Fault Tolerant Control (FTC) have gained central importance over the past decades, due to the increasing requirements of availability, cost efficiency, reliability and operating safety. This thesis deals with the FDD and FTC problems in a spacecraft Attitude Determination and Control System (ADCS). Firstly, the detailed nonlinear models of the spacecraft attitude dynamics and kinematics are described, along with the dynamic models of the actuators and main external disturbance sources. The considered ADCS is composed of an array of four redundant reaction wheels. A set of sensors provides satellite angular velocity, attitude and flywheel spin rate information. Then, general overviews of the Fault Detection and Isolation (FDI), Fault Estimation (FE) and Fault Tolerant Control (FTC) problems are presented, and the design and implementation of a novel diagnosis system is described. The system consists of a FDI module composed of properly organized model-based residual filters, exploiting the available input and output information for the detection and localization of an occurred fault. A proper fault mapping procedure and the nonlinear geometric approach are exploited to design residual filters explicitly decoupled from the external aerodynamic disturbance and sensitive to specific sets of faults. The subsequent use of suitable adaptive FE algorithms, based on the exploitation of radial basis function neural networks, allows to obtain accurate fault estimations. Finally, this estimation is actively exploited in a FTC scheme to achieve a suitable fault accommodation and guarantee the desired control performances. A standard sliding mode controller is implemented for attitude stabilization and control. Several simulation results are given to highlight the performances of the overall designed system in case of different types of faults affecting the ADCS actuators and sensors.

The use of satellite remote sensing for flood risk management

Over the last decades the impact of natural disasters to the global environment is becoming more and more severe. The number of disasters has dramatically increased, as well as the cost to the global economy and the number of people affected. Among the natural disaster, flood catastrophes are considered to be the most costly, devastating, broad extent and frequent, because of the tremendous fatalities, injuries, property damage, economic and social disruption they cause to the humankind. In the last thirty years, the World has suffered from severe flooding and the huge impact of floods has caused hundreds of thousands of deaths, destruction of infrastructures, disruption of economic activity and the loss of property for worth billions of dollars. In this context, satellite remote sensing, along with Geographic Information Systems (GIS), has become a key tool in flood risk management analysis. Remote sensing for supporting various aspects of flood risk management was investigated in the present thesis. In particular, the research focused on the use of satellite images for flood mapping and monitoring, damage assessment and risk assessment. The contribution of satellite remote sensing for the delineation of flood prone zones, the identification of damaged areas and the development of hazard maps was explored referring to selected cases of study.

Development and implementation of a S/W platform to automatically receive and share satellite data

Relazione del lavoro di creazione e implementazione della piattaforma software che sviluppa l’archivio del progetto SATNET. I satelliti universitari hanno un tempo di vista della propria Stazione di Terra di pochi minuti al giorno: SATNET risponde all’esigenza di comunicare con un satellite universitario in orbita bassa per più dei pochi minuti al giorno che una singola Stazione di Terra permette. Questo avviene grazie a una rete di Stazioni di Terra Satellitari collegate da specifiche missioni comuni che mettono in condivisione dati ricevuti da uno o più satelliti, aumentando il rendimento dati/giorno di questi e permettendo una migliore fruizione delle Stazioni di Terra stesse. Il network sfrutta Internet come canale di connessione, e prevede la presenza di un archivio nel quale memorizzare i dati ricevuti, per poi renderne possibile la consultazione e il recupero. Oggetto di questo lavoro di tesi è stato lo sviluppo e l’implementazione di tale archivio: utilizzando un sito web dinamico, il software risponde a tutte le richieste evidenziate nel paragrafo precedente, permettendo a utenti autenticati di inserire dati e ad altri di poterne avere accesso. Il software è completo e funzionante ma non finito, in quanto manca la formulazione di alcune richieste; per esempio non è stato specificato il tipo di informazioni che è possibile caricare in upload, né il tipo di campi richiesti nel modulo di registrazione dei vari utenti. In questi casi sono stati inseriti campi generici, lasciando all’utente la possibilità di modificarli in seguito. Il software è stato dunque concepito come facilmente personalizzabile e modificabile anche da utenti inesperti grazie alla sola lettura della tesi, che rappresenta quindi una vera e propria guida per l’utilizzo, l’installazione, la personalizzazione e la manutenzione della piattaforma software. La tesi evidenzia gli obiettivi e le richieste, mostrando l’aspetto del sito web e le sue funzionalità, e spiega passo per passo il procedimento per la modifica dell’aspetto delle pagine e di alcuni parametri di configurazione. Inoltre, qualora siano necessarie modifiche sostanziali al progetto, introduce i vari linguaggi di programmazione necessari allo sviluppo e alla programmazione web e aiuta l’utente nella comprensione della struttura del software. Si conclude con alcuni suggerimenti su eventuali modifiche, attuabili solo a seguito di un lavoro di definizione degli obiettivi e delle specifiche richieste. In futuro ci si aspetta l’implementazione e la personalizzazione del software, nonché l’integrazione dell’archivio all’interno del progetto SATNET, con l’obiettivo di migliorare e favorire la diffusione e la condivisione di progetti comuni tra diverse Università Europee ed Extra-Europee.

Titanate-based paraelectric glass-ceramics for applications in GHz electronics

Das Gebiet der drahtlosen Kommunikationsanwendungen befindet sich in einem permanenten Entwicklungsprozess (Mobilfunkstandards: GSM/UMTS/LTE/5G, glo-bale Navigationssatellitensysteme (GNSS): GPS, GLONASS, Galileo, Beidou) zu immer höheren Datenraten und zunehmender Miniaturisierung, woraus ein hoher Bedarf für neue, optimierte Hochfrequenzmaterialien resultiert. Diese Entwicklung zeigt sich besonders in den letzten Jahren in der zunehmenden Entwicklung und Anzahl von Smartphones, welche verschiedene Technologien mit unterschiedlichen Arbeitsfrequenzen innerhalb eines Geräts kombinieren (data: 1G-4G, GPS, WLAN, Bluetooth). Die für zukünftige Technologien (z.B. 5G) benötigte Performance-steigerung kann durch die Verwendung von auf MIMO basierenden Antennensystemen realisiert werden (multiple-input & multiple-output, gesteuerte Kombination von mehreren Antennen) für welche auf dielectric Loading basierende Technologien als eine der vielversprechendsten Implementierungslösungen angesehen werden. rnDas Ziel dieser Arbeit war die Entwicklung einer geeigneten paraelektrischen Glaskeramik ($varepsilon_{r}$ > 20, $Qf$ > 5000 GHz, |$tau_f$| < 20 ppm/K; im GHz Frequenzbe-reich) im $mathrm{La_{2}O_{3}}$-$mathrm{TiO_{2}}$-$mathrm{SiO_{2}}$-$mathrm{B_{2}O_{3}}$-System für auf dielectric Loading basierende Mobilfunkkommunikationstechnologien als Alternative zu existierenden kommerziell genutzten Sinterkeramiken. Der Fokus lag hierbei auf der Frage, wie die makroskopi-schen dielektrischen Eigenschaften der Glaskeramik mit ihrer Mikrostruktur korreliert bzw. modifiziert werden können. Es konnte gezeigt werden, dass die dielektrischen Materialanforderungen durch das untersuchte System erfüllt werden und dass auf Glaskeramik basierende Dielektrika weitere vorteilhafte nichtelektro-nische Eigenschaften gegenüber gesinterten Keramiken besitzen, womit dielektrische Glaskeramiken durchaus als geeignete Alternative angesehen werden können. rnEin stabiles Grünglas mit minimalen Glasbildneranteil wurde entwickelt und die chemische Zusammensetzung bezüglich Entglasung und Redoxinstabilitäten optimiert. Geeignete Dotierungen für dielektrisch verlustarme $mathrm{TiO_{2}}$-haltige Glaskeramiken wurden identifiziert.rnDer Einfluss der Schmelzbedingungen auf die Keimbildung wurde untersucht und der Keramisierungsprozess auf einen maximalen Anteil der gewünschten Kristallphasen optimiert um optimale dielektrische Eigenschaften zu erhalten. Die mikroskopische Struktur der Glaskeramiken wurde analysiert und ihr Einfluss auf die makroskopischen dielektrischen Eigenschaften bestimmt. Die Hochfrequenzverlustmechanismen wurden untersucht und Antennen-Prototypenserien wurden analysiert um die Eignung von auf Glaskeramik basierenden Dielektrika für die Verwendung in dielectric Loading Anwendungen zu zeigen.

A new information fusion method for land-use classification using high resolution satellite imagery

Satellite image classification involves designing and developing efficient image classifiers. With satellite image data and image analysis methods multiplying rapidly, selecting the right mix of data sources and data analysis approaches has become critical to the generation of quality land-use maps. In this study, a new postprocessing information fusion algorithm for the extraction and representation of land-use information based on high-resolution satellite imagery is presented. This approach can produce land-use maps with sharp interregional boundaries and homogeneous regions. The proposed approach is conducted in five steps. First, a GIS layer - ATKIS data - was used to generate two coarse homogeneous regions, i.e. urban and rural areas. Second, a thematic (class) map was generated by use of a hybrid spectral classifier combining Gaussian Maximum Likelihood algorithm (GML) and ISODATA classifier. Third, a probabilistic relaxation algorithm was performed on the thematic map, resulting in a smoothed thematic map. Fourth, edge detection and edge thinning techniques were used to generate a contour map with pixel-width interclass boundaries. Fifth, the contour map was superimposed on the thematic map by use of a region-growing algorithm with the contour map and the smoothed thematic map as two constraints. For the operation of the proposed method, a software package is developed using programming language C. This software package comprises the GML algorithm, a probabilistic relaxation algorithm, TBL edge detector, an edge thresholding algorithm, a fast parallel thinning algorithm, and a region-growing information fusion algorithm. The county of Landau of the State Rheinland-Pfalz, Germany was selected as a test site. The high-resolution IRS-1C imagery was used as the principal input data.

Coded slotted aloha with multipacket reception over block fading channels (for satellite networks)

Random access (RA) protocols are normally used in a satellite networks for initial terminal access and are particularly effective since no coordination is required. On the other hand, contention resolution diversity slotted Aloha (CRDSA), irregular repetition slotted Aloha (IRSA) and coded slotted Aloha (CSA) has shown to be more efficient than classic RA schemes as slotted Aloha, and can be exploited also when short packets transmissions are done over a shared medium. In particular, they relies on burst repetition and on successive interference cancellation (SIC) applied at the receiver. The SIC process can be well described using a bipartite graph representation and exploiting tools used for analyze iterative decoding. The scope of my Master Thesis has been to described the performance of such RA protocols when the Rayleigh fading is taken into account. In this context, each user has the ability to correctly decode a packet also in presence of collision and when SIC is considered this may result in multi-packet reception. Analysis of the SIC procedure under Rayleigh fading has been analytically derived for the asymptotic case (infinite frame length), helping the analysis of both throughput and packet loss rates. An upper bound of the achievable performance has been analytically obtained. It can be show that in particular channel conditions the throughput of the system can be greater than one packets per slot which is the theoretical limit of the Collision Channel case.

An inter-comparison between a VIS/IR and a MW satellite-based methods for cloud detection and classification

This thesis is aimed to assess similarities and mismatches between the outputs from two independent methods for the cloud cover quantification and classification based on quite different physical basis. One of them is the SAFNWC software package designed to process radiance data acquired by the SEVIRI sensor in the VIS/IR. The other is the MWCC algorithm, which uses the brightness temperatures acquired by the AMSU-B and MHS sensors in their channels centered in the MW water vapour absorption band. At a first stage their cloud detection capability has been tested, by comparing the Cloud Masks they produced. These showed a good agreement between two methods, although some critical situations stand out. The MWCC, in effect, fails to reveal clouds which according to SAFNWC are fractional, cirrus, very low and high opaque clouds. In the second stage of the inter-comparison the pixels classified as cloudy according to both softwares have been. The overall observed tendency of the MWCC method, is an overestimation of the lower cloud classes. Viceversa, the more the cloud top height grows up, the more the MWCC not reveal a certain cloud portion, rather detected by means of the SAFNWC tool. This is what also emerges from a series of tests carried out by using the cloud top height information in order to evaluate the height ranges in which each MWCC category is defined. Therefore, although the involved methods intend to provide the same kind of information, in reality they return quite different details on the same atmospheric column. The SAFNWC retrieval being very sensitive to the top temperature of a cloud, brings the actual level reached by this. The MWCC, by exploiting the capability of the microwaves, is able to give an information about the levels that are located more deeply within the atmospheric column.

Sea level trends in the Mediterranean from tide gauges and satellite altimetry

Sea level variation is one of the parameters directly related to climate change. Monitoring sea level rise is an important scientific issue since many populated areas of the world and megacities are located in low-lying regions. At present, sea level is measured by means of two techniques: the tide gauges and the satellite radar altimetry. Tide gauges measure sea-level relatively to a ground benchmark, hence, their measurements are directly affected by vertical ground motions. Satellite radar altimetry measures sea-level relative to a geocentric reference and are not affected by vertical land motions. In this study, the linear relative sea level trends of 35 tide gauge stations distributed across the Mediterranean Sea have been computed over the period 1993-2014. In order to extract the real sea-level variation, the vertical land motion has been estimated using the observations of available GPS stations and removed from the tide gauges records. These GPS-corrected trends have then been compared with satellite altimetry measurements over the same time interval (AVISO data set). A further comparison has been performed, over the period 1993-2013, using the CCI satellite altimetry data set which has been generated using an updated modeling. The absolute sea level trends obtained from satellite altimetry and GPS-corrected tide gauge data are mostly consistent, meaning that GPS data have provided reliable corrections for most of the sites. The trend values range between +2.5 and +4 mm/yr almost everywhere in the Mediterranean area, the largest trends were found in the Northern Adriatic Sea and in the Aegean. These results are in agreement with estimates of the global mean sea level rise over the last two decades. Where GPS data were not available, information on the vertical land motion deduced from the differences between absolute and relative trends are in agreement with the results of other studies.

Perennial Snow and Ice Variations (2000-2008) in the Arctic Circumpolar Land Area from Satellite Observations

Perennial snow and ice (PSI) extent is an important parameter of mountain environments with regard to its involvement in the hydrological cycle and the surface energy budget. We investigated interannual variations of PSI in nine mountain regions of interest (ROI) between 2000 and 2008. For that purpose, a novel MODIS data set processed at the Canada Centre for Remote Sensing at 250 m spatial resolution was utilized. The extent of PSI exhibited significant interannual variations, with coefficients of variation ranging from 5% to 81% depending on the ROI. A strong negative relationship was found between PSI and positive degree-days (threshold 0°C) during the summer months in most ROIs, with linear correlation coefficients (r) being as low as r = −0.90. In the European Alps and Scandinavia, PSI extent was significantly correlated with annual net glacier mass balances, with r = 0.91 and r = 0.85, respectively, suggesting that MODIS-derived PSI extent may be used as an indicator of net glacier mass balances. Validation of PSI extent in two land surface classifications for the years 2000 and 2005, GLC-2000 and Globcover, revealed significant discrepancies of up to 129% for both classifications. With regard to the importance of such classifications for land surface parameterizations in climate and land surface process models, this is a potential source of error to be investigated in future studies. The results presented here provide an interesting insight into variations of PSI in several ROIs and are instrumental for our understanding of sensitive mountain regions in the context of global climate change assessment.

Culture's Calling: Mobile Phones, Gender, and the Making of an African Migrant Village in Lisbon

In this article, I explore how immigrants from the West African nation of Guinea-Bissau living in Portugal use mobile phones in their daily lives in Lisbon. Whereas one might assume that mobile phones and other new information technologies facilitate transnational communication between Africa and Portugal, the ethnographic fieldwork that I conducted in Lisbon from 1999 to 2003 revealed a different scenario. Instead, mobile phones as imagined and used by the Guinean immigrants I met in Lisbon revealed less about transnationalism and globalization than they did about constructing community and identity in a new locale. As Guinean immigrants in Portugal reconfigured their relationship to their former colonizers and struggled to make their way in a new, multicultural Europe, they used their mobile phones to engage local networks, shape local identities, and transform Lisbon's sprawl into an African migrant village. Here, I highlight the gendered dimensions of this process and contend that Guinean men's and women's varied uses of mobile phones in Lisbon underscore contrasting experiences of migration, mobility, and belonging.

Culture's Calling: Mobile Phones, Gender, and the Making of an African Migrant Village in Lisbon

In this article, I explore how immigrants from the West African nation of Guinea-Bissau living in Portugal use mobile phones in their daily lives in Lisbon. Whereas one might assume that mobile phones and other new information technologies facilitate transnational communication between Africa and Portugal, the ethnographic fieldwork that I conducted in Lisbon from 1999 to 2003 revealed a different scenario. Instead, mobile phones as imagined and used by the Guinean immigrants I met in Lisbon revealed less about transnationalism and globalization than they did about constructing community and identity in a new locale. As Guinean immigrants in Portugal reconfigured their relationship to their former colonizers and struggled to make their way in a new, multicultural Europe, they used their mobile phones to engage local networks, shape local identities, and transform Lisbon's sprawl into an African migrant village. Here, I highlight the gendered dimensions of this process and contend that Guinean men's and women's varied uses of mobile phones in Lisbon underscore contrasting experiences of migration, mobility, and belonging.

Mobile goes global: The effect of cell phones on economic growth and development

This study investigates the effect of cell phones on economic development and growth by performing an econometric analysis using data from the International Telecommunications Union and the Penn World Table. It discusses the various ways cell phones can make markets more efficient and how the diffusion of information andknowledge plays into development. Several approaches (OLS, Fixed Effects, 2SLS) were used to test over 20 econometric models. Overall, the mobile cellular subscriptions rate was found to have a positive and significant impact on countries’ level of real per capitaGDP and GDP growth rate. Furthermore, the study provides policy implications for the use of technology to promote global growth.