K-41(n, gamma)K-42 thermal and resonance integral cross section measurements

We measured the K-41 thermal neutron absorption and resonance integral cross sections after the irradiation of KNO3 samples near the core of the IEA-R1 IPEN pool-type research reactor. Bare and cadmium-covered targets were irradiated in pairs with Au-Al alloy flux-monitors. The residual activities were measured by gamma-ray spectroscopy with a HPGe detector, with special care to avoid the K-42 decay beta(-) emission effects on the spectra. The gamma-ray self-absorption was corrected with the help of MCNP simulations. We applied the Westcott formalism in the average neutron flux determination and calculated the depression coefficients for thermal and epithermal neutrons due to the sample thickness with analytical approximations. We obtained 1.57(4) and 1.02(4) b, for thermal and resonance integral cross sections, respectively, with correlation coefficient equal to 0.39.

Assessment of integration of the Leprosy Program into primary health care in Aracaju, State of Sergipe, Brazil

Introduction: The aim of this study was to assess the epidemiological and operational characteristics of the Leprosy Program before and after its integration into the Primary Healthcare Services of the municipality of Aracaju-Sergipe, Brazil. Methods: Data were drawn from the national database. The study periods were divided into preintegration (1996-2000) and postintegration (2001-2007). Annual rates of epidemiological detection were calculated. Frequency data on clinico-epidemiological variables of cases detected and treated for the two periods were compared using the Chi-squared (chi(2)) test adopting a 5% level of significance. Results: Rates of detection overall, and in subjects younger than 15 years, were greater for the postintegration period and were higher than rates recorded for Brazil as a whole during the same periods. A total of 780 and 1,469 cases were registered during the preintegration and postintegration periods, respectively. Observations for the postintegration period were as follows: I) a higher proportion of cases with disability grade assessed at diagnosis, with increase of 60.9% to 78.8% (p < 0.001), and at end of treatment, from 41.4% to 44.4% (p < 0.023); II) an increase in proportion of cases detected by contact examination, from 2.1% to 4.1% (p < 0.001); and III) a lower level of treatment default with a decrease from 5.64 to 3.35 (p < 0.008). Only 34% of cases registered from 2001 to 2007 were examined. Conclusions: The shift observed in rates of detection overall, and in subjects younger than 15 years, during the postintegration period indicate an increased level of health care access. The fall in number of patients abandoning treatment indicates greater adherence to treatment. However, previous shortcomings in key actions, pivotal to attaining the outcomes and impact envisaged for the program, persisted in the postintegration period.

Prognostic factors for survival in patients with colorectal liver metastases: experience of a single brazilian cancer center

CONTEXT: Liver metastases are a common event in the clinical outcome of patients with colorectal cancer and account for 2/3 of deaths from this disease. There is considerable controversy among the data in the literature regarding the results of surgical treatment and prognostic factors of survival, and no analysis have been done in a large cohort of patients in Brazil. OBJECTIVES: To characterize the results of surgical treatment of patients with colorectal liver metastases, and to establish prognostic factors of survival in a Brazilian population. METHOD: This was a retrospective study of patients undergoing liver resection for colorectal metastases in a tertiary cancer hospital from 1998 to 2009. We analyzed epidemiologic variables and the clinical characteristics of primary tumors, metastatic disease and its treatment, surgical procedures and follow-up, and survival results. Survival analyzes were done by the Kaplan-Meier method and the log-rank test was applied to determine the influence of variables on overall and disease-free survival. All variables associated with survival with P<0.20 in univariate analysis, were included in multivariate analysis using a Cox proportional hazard regression model. RESULTS: During the period analyzed, 209 procedures were performed on 170 patients. Postope-rative mortality in 90 days was 2.9% and 5-year overall survival was 64.9%. Its independent prognostic factors were the presence of extrahepatic disease at diagnosis of liver metastases, bilateral nodules and the occurrence of major complications after liver surgery. The estimated 5-year disease-free survival was 39.1% and its prognostic factors included R1 resection, extrahepatic disease, bilateral nodules, lymph node involvement in the primary tumor and primary tumors located in the rectum. CONCLUSION: Liver resection for colorectal metastases is safe and effective and the analysis of prognostic factors of survival in a large cohort of Brazilian patients showed similar results to those pointed in international series. The occurrence of major postoperative complications appears to be able to compromise overall survival and further investigation in needed in this topic.

Comparison of the reliability of multifocal visual evoked cortical potentials generated by pattern reversal and pattern pulse stimulation

This study compared the effectiveness of the multifocal visual evoked cortical potentials (mfVEP) elicited by pattern pulse stimulation with that of pattern reversal in producing reliable responses (signal-to-noise ratio >1.359). Participants were 14 healthy subjects. Visual stimulation was obtained using a 60-sector dartboard display consisting of 6 concentric rings presented in either pulse or reversal mode. Each sector, consisting of 16 checks at 99% Michelson contrast and 80 cd/m² mean luminance, was controlled by a binary m-sequence in the time domain. The signal-to-noise ratio was generally larger in the pattern reversal than in the pattern pulse mode. The number of reliable responses was similar in the central sectors for the two stimulation modes. At the periphery, pattern reversal showed a larger number of reliable responses. Pattern pulse stimuli performed similarly to pattern reversal stimuli to generate reliable waveforms in R1 and R2. The advantage of using both protocols to study mfVEP responses is their complementarity: in some patients, reliable waveforms in specific sectors may be obtained with only one of the two methods. The joint analysis of pattern reversal and pattern pulse stimuli increased the rate of reliability for central sectors by 7.14% in R1, 5.35% in R2, 4.76% in R3, 3.57% in R4, 2.97% in R5, and 1.78% in R6. From R1 to R4 the reliability to generate mfVEPs was above 70% when using both protocols. Thus, for a very high reliability and thorough examination of visual performance, it is recommended to use both stimulation protocols.

Acúmulo de minerais em Aechmea blanchetiana (Baker) L.B. Smith (Bromeliaceae), contaminadas com zinco em cultivo in vitro

Com o objetivo de estudar a absorção e translocação de Ca, Co, Fe, K e Zn em Aechmea blanchetiana, plantas foram cultivadas in vitro em meios de cultivo contendo concentrações de Zn (0,0; 0,18; 1,8; 18 e 180 mg Zn L-1). Após 16 semanas de cultivo, os sistemas aéreo e radicular foram separados e determinadas à massa seca para massa de matéria seca e para a análise por ativação com nêutrons (AAN). O procedimento consistiu em irradiar amostras e padrões no reator nuclear de pesquisa IEA-R1 por 16 h para análise por espectrometria de raios gama. O controle dos resultados foi avaliado por meio das análises dos materiais de referência certificados, com desvios padrão relativo de 9,1 % e erros inferiores a 12,9 %. Os resultados das determinações dos elementos mostraram que o Zn alterou absorção e translocação de Ca, Co, Fe, K e Zn. A espécie apresentou alta quantidade de Zn nos sistemas aéreo e radicular indicando, possivelmente, ser bioacumuladora desse elemento.

Fluorcalciomicrolite, (Ca,Na,□)2Ta2O6F, a new microlite-group mineral from Volta Grande pegmatite, Nazareno, Minas Gerais, Brazil

Fluorcalciomicrolite, (Ca,Na,□)2Ta2O6F, is a new microlite-group, pyrochlore supergroup mineral approved by the CNMNC (IMA 2012-036). It occurs as an accessory mineral in the Volta Grande pegmatite, Nazareno, Minas Gerais, Brazil. Associated minerals include: microcline, albite, quartz, muscovite, spodumene, "lepidolite", cassiterite, tantalite-(Mn), monazite-(Ce), fluorite, "apatite", beryl, "garnet", epidote, magnetite, gahnite, zircon, "tourmaline", bityite, hydrokenomicrolite, and other microlite-group minerals under study. Fluorcalciomicrolite occurs as euhedral, untwinned, octahedral crystals 0.1-1.5 mm in size, occasionally modified by rhombododecahedral faces. The crystals are colourless and translucent; the streak is white, and the lustre is adamantine to resinous. It does not fluoresce under ultraviolet light. Mohs' hardness is 4½- 5, tenacity is brittle. Cleavage is not observed; fracture is conchoidal. The calculated density is 6.160 g/cm3. The mineral is isotropic, ncalc. = 1.992. The Raman spectrum is dominated by bands of B-X octahedral bond stretching and X-B-X bending modes.The chemical composition (n = 6) is (by wavelength dispersive spectroscopy, H2O calculated to obtain charge balance, wt.%): Na2O 4.68, CaO 11.24, MnO 0.01, SrO 0.04, BaO 0.02, SnO2 0.63, UO2 0.02, Nb2O5 3.47, Ta2O5 76.02, F 2.80, H2O 0.48, O=F -1.18, total 98.23. The empirical formula, based on 2 cations at the B site, is (Ca1.07Na0.81□0.12)∑2.00(Ta1.84Nb0.14Sn0.02)∑2.00 [O5.93(OH)0.07]6.00[F0.79(OH)0.21]. The strongest eight X-ray powder-diffraction lines [d in Å(I)(hkl)] are: 5.997(59)(111), 3.138(83)(311), 3.005(100)(222), 2.602(29)(400), 2.004(23)(511), 1.841(23)(440), 1.589(25)(533), and 1.504(24)(444). The crystal structure refinement (R1 = 0.0132) gave the following data: cubic, Fd3m, a = 10.4191(6) Å, V = 1131.07(11) Å3, Z = 8.

Effect of culture system and diet in early larval stages over skeletal deformities development in gilthead sea bream

[ES] Main deformities such as lordosis, opercular deformities and upper/lower jaws shortening are considered as quality descriptors in commercial marine fish fry production and seem to be related with larval culture conditions in early larval stages. The aim of this work was to obtain information about the contribution of the diet and rearing system to the apparition of these abnormalities in gilthead sea bream (Sparus aurata) larvae in semi-industrial scale facilities. For that purpose, two different larval rearing systems semi-intensive and intensive were compared; besides, two different rotifer enrichments, DHA Protein Selco, (Inve Aquaculture, Dendermonde, Belgium) (R1) and Red Pepper Paste, (Bernaqua bvba, Turnhout, Belgium) were tested in the intensive system. Biochemical composition of larvae, preys and commercial products was analysed. At 50 days post hatching six hundred fish per treatment were individually studied under stereoscope and deformity frequency recorded. Besides at 95 days post hatching fry were soft X ray monitored. Both rotifer enrichment and rearing system affected survival, growth and deformity frequency. Rearing system did not affect total larvae fatty acid content except at 20 dah, where DHA were significantly higher and EPA significantly lower in Semi-intensive system. A significantly lower percentage of deformity rates together with better survival and growth were obtained in the semi-intensive system. In dietary treatment, rotifer enrichment significantly affected larval survival. R1 rotifers enrichment significantly (P<0.05) improved survival when compared to fed R2 larvae. The content of DPA was significantly (P<0.05) higher in R2 fed larvae reflecting the R2 rotifers content of this fatty acid. The level of this FA tended to decrease in concordance with the rotifers replacement by artemia in the diet. The effects n-3-HUFA and DPA (22:5n-6) over larval survival and skeletal deformities development is discussed.

Modellazione e simulazione di sistemi meccanici ad elevato numero di gradi di libertà mediante metodi non convenzionali e sistemi CAD

Recent developments in piston engine technology have increased performance in a very significant way. Diesel turbocharged/turbo compound engines, fuelled by jet fuels, have great performances. The focal point of this thesis is the transformation of the FIAT 1900 jtd diesel common rail engine for the installation on general aviation aircrafts like the CESSNA 172. All considerations about the diesel engine are supported by the studies that have taken place in the laboratories of the II Faculty of Engineering in Forlì. This work, mostly experimental, concerns the transformation of the automotive FIAT 1900 jtd – 4 cylinders – turbocharged – diesel common rail into an aircraft engine. The design philosophy of the aluminium alloy basement of the spark ignition engine have been transferred to the diesel version while the pistons and the head of the FIAT 1900 jtd are kept in the aircraft engine. Different solutions have been examined in this work. A first V 90° cylinders version that can develop up to 300 CV and whose weight is 30 kg, without auxiliaries and turbocharging group. The second version is a development of e original version of the diesel 1900 cc engine with an optimized crankshaft, that employ a special steel, 300M, and that is verified for the aircraft requirements. Another version with an augmented stroke and with a total displacement of 2500 cc has been examined; the result is a 30% engine heavier. The last version proposed is a 1600 cc diesel engine that work at 5000 rpm, with a reduced stroke and capable of more than 200 CV; it was inspired to the Yamaha R1 motorcycle engine. The diesel aircraft engine design keeps the bore of 82 mm, while the stroke is reduced to 64.6 mm, so the engine size is reduced along with weight. The basement weight, in GD AlSi 9 MgMn alloy, is 8,5 kg. Crankshaft, rods and accessories have been redesigned to comply to aircraft standards. The result is that the overall size is increased of only the 8% when referred to the Yamaha engine spark ignition version, while the basement weight increases of 53 %, even if the bore of the diesel version is 11% lager. The original FIAT 1900 jtd piston has been slightly modified with the combustion chamber reworked to the compression ratio of 15:1. The material adopted for the piston is the aluminium alloy A390.0-T5 commonly used in the automotive field. The piston weight is 0,5 kg for the diesel engine. The crankshaft is verified to torsional vibrations according to the Lloyd register of shipping requirements. The 300M special steel crankshaft total weight is of 14,5 kg. The result reached is a very small and light engine that may be certified for general aviation: the engine weight, without the supercharger, air inlet assembly, auxiliary generators and high pressure body, is 44,7 kg and the total engine weight, with enlightened HP pump body and the titanium alloy turbocharger is less than 100 kg, the total displacement is 1365 cm3 and the estimated output power is 220 CV. The direct conversion of automotive piston engine to aircrafts pays too huge weight penalties. In fact the main aircraft requirement is to optimize the power to weight ratio in order to obtain compact and fast engines for aeronautical use: this 1600 common rail diesel engine version demonstrates that these results can be reached.

I rifiuti da apparecchiature elettriche ed elettroniche (RAEE) - Aspetti tecnico-gestionali e ambientali

I RAEE (Rifiuti da Apparecchiature Elettriche ed Elettroniche) costituiscono un problema prioritario a livello europeo per quanto riguarda la loro raccolta, stoccaggio, trattamento, recupero e smaltimento, essenzialmente per i seguenti tre motivi: Il primo riguarda le sostanze pericolose contenute nei RAEE. Tali sostanze, nel caso non siano trattate in modo opportuno, possono provocare danni alla salute dell’uomo e all’ambiente. Il secondo è relativo alla vertiginosa crescita relativa al volume di RAEE prodotti annualmente. La crescita è dovuta alla continua e inesorabile commercializzazione di prodotti elettronici nuovi (è sufficiente pensare alle televisioni, ai cellulari, ai computer, …) e con caratteristiche performanti sempre migliori oltre all’accorciamento del ciclo di vita di queste apparecchiature elettriche ed elettroniche (che sempre più spesso vengono sostituiti non a causa del loro malfunzionamento, ma per il limitato livello di performance garantito). Il terzo (ed ultimo) motivo è legato all’ambito economico in quanto, un corretto trattamento dei RAEE, può portare al recupero di materie prime secondarie (alluminio, ferro, acciaio, plastiche, …) da utilizzare per la realizzazione di nuove apparecchiature. Queste materie prime secondarie possono anche essere vendute generando profitti considerevoli in ragione del valore di mercato di esse che risulta essere in costante crescita. Questo meccanismo ha portato a sviluppare un vasto quadro normativo che regolamenta tutto l’ambito dei RAEE dalla raccolta fino al recupero di materiali o al loro smaltimento in discarica. È importante inoltre sottolineare come lo smaltimento in discarica sia da considerarsi come una sorta di ‘ultima spiaggia’, in quanto è una pratica piuttosto inquinante. Per soddisfare le richieste della direttiva l’obiettivo dev’essere quello di commercializzare prodotti che garantiscano un minor impatto ambientale concentrandosi sul processo produttivo, sull’utilizzo di materiali ‘environmentally friendly’ e sulla gestione consona del fine vita. La Direttiva a livello europeo (emanata nel 2002) ha imposto ai Paesi la raccolta differenziata dei RAEE e ha definito anche un obiettivo di raccolta per tutti i suoi Stati Membri, ovvero 4 kg di RAEE raccolti annualmente da ogni abitante. Come riportato di seguito diversi paesi hanno raggiunto l’obiettivo sopra menzionato (l’Italia vi è riuscita nel 2010), ma esistono anche casi di paesi che devono necessariamente migliorare il proprio sistema di raccolta e gestione dei RAEE. Più precisamente in Italia la gestione dei RAEE è regolamentata dal Decreto Legislativo 151/2005 discusso approfonditamente in seguito ed entrato in funzione a partire dal 1° Gennaio 2008. Il sistema italiano è basato sulla ‘multi consortilità’, ovvero esistono diversi Sistemi Collettivi che sono responsabili della gestione dei RAEE per conto dei produttori che aderiscono ad essi. Un altro punto chiave è la responsabilità dei produttori, che si devono impegnare a realizzare prodotti durevoli e che possano essere recuperati o riciclati facilmente. I produttori sono coordinati dal Centro di Coordinamento RAEE (CDC RAEE) che applica e fa rispettare le regole in modo da rendere uniforme la gestione dei RAEE su tutto il territorio italiano. Il documento che segue sarà strutturato in quattro parti. La prima parte è relativa all’inquadramento normativo della tematica dei RAEE sia a livello europeo (con l’analisi della direttiva ROHS 2 sulle sostanze pericolose contenute nei RAEE e la Direttiva RAEE), sia a livello italiano (con un’ampia discussione sul Decreto Legislativo 151/2005 e Accordi di Programma realizzati fra i soggetti coinvolti). La seconda parte tratta invece il sistema di gestione dei RAEE descrivendo tutte le fasi principali come la raccolta, il trasporto e raggruppamento, il trattamento preliminare, lo smontaggio, il riciclaggio e il recupero, il ricondizionamento, il reimpiego e la riparazione. La terza definisce una panoramica delle principali metodologie di smaltimento dei 5 raggruppamenti di RAEE (R1, R2, R3, R4, R5). La quarta ed ultima parte riporta i risultati a livello italiano, europeo ed extra-europeo nella raccolta dei RAEE, avvalendosi dei report annuali redatti dai principali sistemi di gestione dei vari paesi considerati.

Materialeigenschaften und Optimierungspotential von farbigen Korunden am Beispiel vietnamesischer und synthetischer Rubine

Die vorliegende Arbeit beschäftigt sich mit Rubinen der drei derzeit bedeutendsten Vorkommen in Nord-Vietnam, mit ihrer Entstehung, ihrer Charakterisierung, ihrem Edelsteinpotential und ihren Materialeigenschaften im Kontext mit handelsüblichen Synthesen. Zur Erstellung der hierfür erforderlichen Datenbanken wurden sowohl phasenanalytische wie chemisch-analytische als auch spektroskopische Methoden benutzt und die Ergebnisse mit den Erkenntnissen klassischer gemmologischer Untersuchungsmethoden interpretiert. Die natürlichen Bildungsbedingungen der Rubine werden der granulit-faziellen Metamorphose der Day Nui Con Voi - Zone innerhalb der Red River Ailao Shan - Region Südostasiens zugerechnet. Marmore, Gneise und Mobilisationszonen zwischen sehr unterschiedlichen Gesteinen sind dabei zu Trägern von oxidischen Edelsteinmineralen wie Rubin und Spinell geworden, gleichzeitig entstandene Magmatite führen silikatische Edelsteinminerale wie Turmalin und Topas.Mit IR-, Ramanspektroskopie, Elektronstrahl-Mikrosonde und Edelsteinmikroskop werden Kaolinit, Boehmit, Glimmer, Diaspor, Calcit, Zirkon, Turmalin, Graphit, Rutil als charakterisierende Mineraleinschlüsse in vietnamesischen Rubinen bestimmt. Die chemische Zusammensetzung vietnamesischer und synthetischer Rubine wurde mit der Elektronenstrahl-Mikrosonde untersucht. Die vietnamesischen Rubine von Yen Bai, Luc Yen und Nghe An sind aufgrund spezieller Spurenelement-Kombinationen und auch durch Absolutgehalte bestimmter Elemente relativ sicher von Synthesen jeglicher Art zu unterscheiden; selbst die qualitativ besten Synthesen (Douros), die mit klassischen Methoden nur schwer als solche zu identifizieren sind, können von hochwertigen natürlichen Rubinen differenziert werden. Polarisierte Absorptionsspektren vietnamesischer Rubine zeigen die typischen Banden des Cr3+ in der Kristallstruktur des Rubins bei 17953 cm-1; 24570 cm-1 (E?c) sowie 17985 cm-1 und 25125 cm-1 (E//c). Sie entsprechen den Spinübergängen 4A2g?4T2g(4F) und 4A2g?4T1g(4F); eine zu beobachtende Verschiebung der Spektrenkante bei 32500 cm-1 zu 35000 cm-1 nach Temperaturbehandlung wird wahrscheinlich von V3+ verursacht. Mit Laser-Fluoreszenzspektroskopie wurden polarisierte Emissionsspektren von ausgewählten Rubinen mit spezieller Spurenelementchemie aufgenommen; dabei konnte die Schwächung der Fluoreszenzintensität von Cr durch Fe festgestellt werden. Die Emissionsspektren bestehen aus dem charakteristischen Chromdublett (R1 und R2 Linien bei etwa 693 nm und 694 nm), Seitenbanden in Stoke und anti Stoke-Bereich und n-Linien, die auf die Emission benachbarter, farbwirksamer Ionenpaare zurückzuführen sind. Das Verhältnis der Intensitäten der n-Linien bei 702 nm und 705 nm zu den Seitenbandenlinien bei 713 nm zeigt im untersuchten Cr3+-Konzentrationsbereich eine nahezu lineare Abhängigkeit zur Cr3+-Konzentration, unabhängig von der Anregungswellenlänge und der Fe-Konzentration. Die in vietnamesischen Rubinen häufig vorkommenden blauen Farbzonen werden durch elektronische Wechselwirkung von Fe2+/Fe3+ und Fe2+/Ti4+ -Kombinationen verursacht und können für den Edelstein schadlos durch geeignete Temperaturbehandlung eliminiert werden.

Role of caveolin-1 in the proliferation of solid tumours in vitro

Caveolin-1 (Cav-1), the essential structural constituent of caveolae, which are flask-shaped invaginations of the plasma membrane, has been found to play a key role in the modulation of cell proliferation and cancer development. It seems to act as an oncosuppressor or a promoter of growth, depending on the histotype, stage and grade of each tumour. The aim of this study was to analyze the effects of Caveolin-1 gene silencing on the proliferation of human lung cancer and osteosarcoma in vitro. Our data show that Cav-1 silencing blocks the growth in both metastatic lung cancer cell lines analyzed, suggesting a proliferation promoting action of the protein in these cells. A marked decrease of phospho-Akt, phospho-ERK, STAT3, cyclin D1, CDK4 and consequently of phospho-Rb expression was evident in the cells treated with Cav-1 siRNA. With regards to osteosarcoma, we demonstrated that the suppression of Cav-1 results in the blocking of MG-63 and in the slowing down of HOS proliferation, suggesting a role for Cav-1 as a promoter of tumour growth in these cell lines. A marked decrease of phospho-Akt, cyclin E, CDK2 and phospho-Rb and an increase of p21 expression levels were evident in the cells treated with Cav-1 siRNA. Our results suggest two new cell cycle inhibiting pathways, mediated by Cav-1 knock-down, and provide new insights into the molecular mechanisms underlying the tumour-promoting role of Cav-1 in lung cancer and osteosarcoma. In this work we also investigated the role of estrogens in lung cancer and the functional cross-talk between Cav-1 and estrogens/estrogen receptors in it. Our results show that 17β-estradiol induces proliferation either in RAL or in SCLC-R1 cells and that both cell lines are sensitive to 4-OHT antiproliferative effect. The sensitivity to estrogen stimulation seems to be gender- and/or histological type-independent in metastatic lung cancer in vitro.

Advanced Waste-To-Energy Cycles

The increase in environmental and healthy concerns, combined with the possibility to exploit waste as a valuable energy resource, has led to explore alternative methods for waste final disposal. In this context, the energy conversion of Municipal Solid Waste (MSW) in Waste-To-Energy (WTE) power plant is increasing throughout Europe, both in terms of plants number and capacity, furthered by legislative directives. Due to the heterogeneous nature of waste, some differences with respect to a conventional fossil fuel power plant have to be considered in the energy conversion process. In fact, as a consequence of the well-known corrosion problems, the thermodynamic efficiency of WTE power plants typically ranging in the interval 25% ÷ 30%. The new Waste Framework Directive 2008/98/EC promotes production of energy from waste introducing an energy efficiency criteria (the so-called “R1 formula”) to evaluate plant recovery status. The aim of the Directive is to drive WTE facilities to maximize energy recovery and utilization of waste heat, in order to substitute energy produced with conventional fossil fuels fired power plants. This calls for novel approaches and possibilities to maximize the conversion of MSW into energy. In particular, the idea of an integrated configuration made up of a WTE and a Gas Turbine (GT) originates, driven by the desire to eliminate or, at least, mitigate limitations affecting the WTE conversion process bounding the thermodynamic efficiency of the cycle. The aim of this Ph.D thesis is to investigate, from a thermodynamic point of view, the integrated WTE-GT system sharing the steam cycle, sharing the flue gas paths or combining both ways. The carried out analysis investigates and defines the logic governing plants match in terms of steam production and steam turbine power output as function of the thermal powers introduced.

Transgenic mice as a tool for depression research: examples from the endocannabinoid and the corticotropin-releasing hormone system

Major depression belongs to the most serious and widespread psychiatric disorders in today’s society. There is a great need for the delineation of the underlying molecular mechanisms as well as for the identification of novel targets for its treatment. In this thesis, transgenic mice of the endocannabinoid and the corticotropin-releasing hormone (CRH) system were investigated to determine the putative role of these systems for depression-like phenotypes in mice. In the first part of the thesis, we found that the endocannabinoid system was prominently involved in a brain region-specific and temporally controlled manner in acute as well as in chronic stress processing. Genetic deletion in combination with pharmacological intervention revealed the importance of a fully functional endocannabinoid system for efficient neuroendocrine and behavioral stress coping. Accordingly, cannabinoid type 1 (CB1) receptor-deficient mice displayed several depression-like symptoms and molecular alterations, including “behavioral despair”, stress hormone hypersecretion and decreased glucocorticoid receptor and brain-derived neurotrophic factor expression in the hippocampus. However, the endocannabinoid system was dispensable for the efficacy of currently used antidepressant drugs. To facilitate future endocannabinoid research, a transgenic mouse was generated, which overexpressed the CB1 receptor protein fused to a fluorescent protein. In the second part of the thesis, conditional brain region-specific CRH overexpressing mice were evaluated as a model for pathological chronic CRH hyperactivation. Mutant mice showed aberrant neuroendocrine and behavioral stress coping and hyperarousal due to CRH-induced activation of the noradrenergic system in the brain. Mutant mice appeared to share similarities with naturally occurring endogenous CRH activation in wild-type mice and were sensitive to acute pharmacological blockade of CRH receptor type 1 (CRH-R1). Thus, CRH overexpressing mice serve as an ideal in vivo tool to evaluate the efficacy of novel CRH-R1 antagonists. Together, these findings highlight the potential of transgenic mice for the understanding of certain endo-phenotypes (isolated symptoms) of depression and their molecular correlates.

Molekularer Magnetismus und Multistabilitäten in sternförmigen cyanidgebrückten Eisen- und Übergangsmetall-Komplexverbindungen

In der hier vorliegenden Arbeit wurden neue eisenhaltige Spincrossover-Komplexerndargestellt und deren magnetische Eigenschaften untersucht. Ausgehend von früheren Ergebnissen wurden verschiedene Strategien zur Optimierung der Eisen-Spincrossover Verbindungen verfolgt. Wie schon früher dokumentiert finden sich bei Eisen-Übergangsmetall Komplexen eine Vielzahl von Spincrossover Phänomenen. Ebenso gut dokumentiert sind die Möglichen Änderungen des Spin Zustandes durch äußere Einflüsse wie Temperatur, Druck oder Licht. Darauf aufbauend wurden nunrnverschiedene Eisenkomplexe synthetisiert und auf das Spincrossover Phänomen hin untersucht. Dazu wurden zum Einen Fe(II) Komplexe vom Typ [FeL1(NCS)2] (L1 = pmea, pmap, tepa and tmpa) betrachtet und zum anderen Sternförmige Fe(III) Komplexe vom Typ [M{(CN-FeIIIL2}x]y+. (M=Fe(II), Co(III), Mo(IV), Ru(II)) undrndodecanukleare Komplexe vom Typ [(L2Fe(III)NC)5Fe(II)CNCo(III)(CNFe(III)L2)5]4+. L2= Bis(R2,3,4 -salicylidenaminoalkyl-R1-amin. Thermischen Spincrossover und LIESST zeigen [3,3/N-H/Sal-H/Fe/Co]; [3,3/N-H/Sal-H/Fe/Ru]; [3,3/N-H/sal-H/Fe/Mo]; [3,3/N-H/Sal-H/Fe/W]; FeII(pmea)(SCN)2; thermischen Spinübergang zeigt [2,3/N-H/Sal-H/Fe/Fe-Co]. Die Ethylen gebrückten Komplexe zeigen weniger guten oder gar keinen Schalteffekt im Gegensatz zum Propylen gebrückten Komplexe. Fe(II)(PMEA)(SCN)2 zeigt vollständigen thermischen Spinübergang von High Spin nach Low Spin ein LIESST und einen LiPTH Effekt.

Development Of New Toolkits For Orbit Determination Codes For Precise Radio Tracking Experiments

This thesis describes the developments of new models and toolkits for the orbit determination codes to support and improve the precise radio tracking experiments of the Cassini-Huygens mission, an interplanetary mission to study the Saturn system. The core of the orbit determination process is the comparison between observed observables and computed observables. Disturbances in either the observed or computed observables degrades the orbit determination process. Chapter 2 describes a detailed study of the numerical errors in the Doppler observables computed by NASA's ODP and MONTE, and ESA's AMFIN. A mathematical model of the numerical noise was developed and successfully validated analyzing against the Doppler observables computed by the ODP and MONTE, with typical relative errors smaller than 10%. The numerical noise proved to be, in general, an important source of noise in the orbit determination process and, in some conditions, it may becomes the dominant noise source. Three different approaches to reduce the numerical noise were proposed. Chapter 3 describes the development of the multiarc library, which allows to perform a multi-arc orbit determination with MONTE. The library was developed during the analysis of the Cassini radio science gravity experiments of the Saturn's satellite Rhea. Chapter 4 presents the estimation of the Rhea's gravity field obtained from a joint multi-arc analysis of Cassini R1 and R4 fly-bys, describing in details the spacecraft dynamical model used, the data selection and calibration procedure, and the analysis method followed. In particular, the approach of estimating the full unconstrained quadrupole gravity field was followed, obtaining a solution statistically not compatible with the condition of hydrostatic equilibrium. The solution proved to be stable and reliable. The normalized moment of inertia is in the range 0.37-0.4 indicating that Rhea's may be almost homogeneous, or at least characterized by a small degree of differentiation.