Miscibility and crystallization of PHB PMA blends

The miscibility, crystallization behavior and morphological structure of PHB/PMA blends have been studied by the differential scanning calorimeter (DSC) and polarized optical microscopy (POM). The chemical repeat units of the two components of the blend are isomers. The results indicate that PHB and PMA are miscible in the melt. The addition of PMA into PHB results in a depression in the spherulite growth rate of PHB. With increasing PMA content in the blends, the texture of PHB spherulite becomes more open.

Nanoscale electronic properties of conjugated polymers and nanocrystals

The objective of this thesis is the exploration and characterisation of the nanoscale electronic properties of conjugated polymers and nanocrystals. In Chapter 2, the first application of conducting-probe atomic force microscopy (CP-AFM)-based displacement-voltage (z-V) spectroscopy to local measurement of electronic properties of conjugated polymer thin films is reported. Charge injection thresholds along with corresponding single particle gap and exciton binding energies are determined for a poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] thin film. By performing measurements across a grid of locations on the film, a series of exciton binding energy distributions are identified. The variation in measured exciton binding energies is in contrast to the smoothness of the film suggesting that the variation may be attributable to differences in the nano-environment of the polymer molecules within the film at each measurement location. In Chapter 3, the CP-AFM-based z-V spectroscopy method is extended for the first time to local, room temperature measurements of the Coulomb blockade voltage thresholds arising from sequential single electron charging of 28 kDa Au nanocrystal arrays. The fluid-like properties of the nanocrystal arrays enable reproducible formation of nanoscale probe-array-substrate junctions, allowing the influence of background charge on the electronic properties of the array to be identified. CP-AFM also allows complementary topography and phase data to be acquired before and after spectroscopy measurements, enabling comparison of local array morphology with local measurements of the Coulomb blockade thresholds. In Chapter 4, melt-assisted template wetting is applied for the first time to massively parallel fabrication of poly-(3-hexylthiophene) nanowires. The structural characteristics of the wires are first presented. Two-terminal electrical measurements of individual nanowires, utilising a CP-AFM tip as the source electrode, are then used to obtain the intrinsic nanowire resistivity and the total nanowire-electrode contact resistance subsequently allowing single nanowire hole mobility and mean nanowire-electrode barrier height values to be estimated. In Chapter 5, solution-assisted template wetting is used for fabrication of fluorene-dithiophene co-polymer nanowires. The structural characteristics of these wires are also presented. Two-terminal electrical measurements of individual nanowires indicate barrier formation at the nanowire-electrode interfaces and measured resistivity values suggest doping of the nanowires, possibly due to air exposure. The first report of single conjugated polymer nanowires as ultra-miniature photodetectors is presented, with single wire devices yielding external quantum efficiencies ~ 0.1 % and responsivities ~ 0.4 mA/W under monochromatic illumination.

Design and synthesis of hierarchical MnO2 nanospheres/carbon nanotubes/conducting polymer ternary composite for high performance electrochemical electrodes.

For efficient use of metal oxides, such as MnO(2) and RuO(2), in pseudocapacitors and other electrochemical applications, the poor conductivity of the metal oxide is a major problem. To tackle the problem, we have designed a ternary nanocomposite film composed of metal oxide (MnO(2)), carbon nanotube (CNT), and conducting polymer (CP). Each component in the MnO(2)/CNT/CP film provides unique and critical function to achieve optimized electrochemical properties. The electrochemical performance of the film is evaluated by cyclic voltammetry, and constant-current charge/discharge cycling techniques. Specific capacitance (SC) of the ternary composite electrode can reach 427 F/g. Even at high mass loading and high concentration of MnO(2) (60%), the film still showed SC value as high as 200 F/g. The electrode also exhibited excellent charge/discharge rate and good cycling stability, retaining over 99% of its initial charge after 1000 cycles. The results demonstrated that MnO(2) is effectively utilized with assistance of other components (fFWNTs and poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) in the electrode. Such ternary composite is very promising for the next generation high performance electrochemical supercapacitors.

Notes on the Asymmetric Hydrogenation of Methyl Acetoacetate in Neoteric Solvents

Asymmetric hydrogenation of methyl acetoacetate to methyl (R)-3-hydroxybutyrate by [(R)-RuCl(binap)( p-cymen)] Cl has been studied in methanol-ionic liquid and methanol-dense CO(2) solvent systems. The ionic pairs triethylhexylammonium and 1-methylimidazolium with bis(trifluoromethane sulfonyl) imide and hexafluorophosphates were used. The role of ionic pairs on the kinetic parameters and (enantio) selectivity has been demonstrated. Although the CO(2) expanded methanol system suffered from a reduction in both reaction rate and product selectivity, this changed in the presence of water. The high selectivity of the optimized methanol-CO(2)-water-halide system was designed as a consequence of observed additive effects.

Modified electrodes with Keggin-type polyoxotungstates

O objectivo deste trabalho é a produção de novos eléctrodos modificados com polioxotungstatos (POMs) do tipo Keggin, incluindo POMs lacunares e substituídos por metais de transição. A preparação e caracterização dos polioxotungstatos encontram-se descritas no Capítulo 2. No Capítulo 3 descreve-se a produção de eléctrodos de carbono vítreo funcionalizados com sais híbridos de tetra-n-butilamónio de vários silicotungstatos pelo método de evaporação da gota. As propriedades electroquímicas dos polioxotungstatos imobilizados foram comparadas com as das espécies solúveis correspondentes. A morfologia dos depósitos foi avaliada por microscopia óptica e por microscopia electrónica de varrimento. No capítulo 4 descreve-se a preparação de novos eléctrodos compósitos de carbono e poli(hexilmetacrilato) com fosfotungstatos. Os estudos electroquímicos revelaram que as principais características dos POMs são mantidas e que os processos de redução são controlados por difusão, dependendo da difusão dos protões da solução. O Capítulo 5 descreve a construção de filmes em multicamadas ultrafinos contendo POMs e polietilenimina, preparados pelo método de auto-montagem camada-sobre-camada em eléctrodos de carbono vítreo. Os filmes em multicamada foram caracterizados por voltametria cíclica e por microscopia electrónica de varrimento e foi usada a espectroscopia de absorção de UV-Vis em placas de quartzo para monitorar o crescimento de filme. Os resultados voltamétricos revelaram que os processos de redução dos POM são confinados à superfície. Alguns destes eléctrodos modificados revelaram propriedades electrocatalíticas relativamente à redução dos aniões nitrito, bromato e/ou iodato. A espectroscopia de impedância electroquímica também foi usada na caracterização destes filmes e os resultados revelaram que a resistência à transferência de carga aumenta com o aumento do número de bicamadas para ambas as espécies redox, indicando que a espessura do filme tem um efeito importante sobre a cinética de reacções de transferência de carga. No capítulo 6 descreve-se a síntese de filmes híbridos orgânicos/inorgânicos compostos por poli(3,4-etilenodioxitiofeno) (PEDOT) e por silicotungstatos do tipo Keggin através da polimerização electroquímica, em condições aquosas, na superfície de electrodos de carbono vítreo. A voltametria cíclica revelou que as características principais dos POMs são mantidas nos filmes. Verificou-se que estes filmes são muito estáveis, possivelmente devido a fortes interacções electrostáticas entre os POMs aniónicos e o polímero positivamente carregado. A espectroscopia de impedância electroquímica foi também utilizada e os resultados mostraram que a resistência de transferência de carga aumenta com o aumento do pH e para valores de potenciais mais elevados. O capítulo 7 apresenta as conclusões finais e possíveis trabalhos futuros.

Caracterização e transformação de Lenhosulfonatos de Eucalyptus globulus

Os lenhosulfonatos representam um sub-produto formado durante o cozimento ao sulfito ácido, sendo queimados para a regeneração da base e recuperação de energia. No entanto, os lenhosulfonatos são também considerados uma importante matéria-prima para a produção de vários produtos de valor acrescentado. Os objectivos principais deste trabalho foram contribuir para uma melhor compreensão sobre a caracterização química e estrutural dos lenhosulfonatos do Eucalyptus globulus, assim como, para complementar a informação disponível sobre a síntese e a caracterização estrutural e térmica de materiais poliméricos obtidos a partir de compostos modelo dos produtos de oxidação dos lenhosulfonatos. O licor de cozimento ao sulfito foi analisado em termos do teor de cinzas, extractáveis, compostos voláteis, açúcares e lenhosulfonatos. O teor de cinzas e açúcares no licor de cozimento é muito elevado, tendo sido necessário purificar o mesmo (2,8-13,8 % e 3,2-9,1 %, respectivamente). A análise dos açúcares mostrou uma quantidade considerável de pentoses, sendo o açúcar predominante a xilose. Os lenhosulfonatos foram purificados, isolados e caracterizados por química molhada (titulação potenciométrica e oxidação com permanganato), análise elementar, espectroscopia de ultravioleta/visível (UV/Vis), espectroscopia de infravermelho de transformada de Fourier (FTIR), espectroscopia de ressonância magnética nuclear de protão (RMN de 1H) e carbono (RMN de 13C), espectrometria de massa de ionização por electrospray (ESI-MS), cromatografia de permeação em gel (GPC), termogavimetria (TGA) e calorimetria diferencial de varrimento (DSC). Os lenhosulfonatos são constituídos principalmente por unidades S, são parcialmente sulfonados e possuem um peso molecular relativamente baixo (Mw = 1250-2400 Da). A ruptura das ligações β-O-4 e α-O-4 da lenhina do Eucalyptus globulus após cozimento ao sulfito ácido originam olígomeros de baixo peso molecular cuja estrutura foi elucidada por RMN 1D/2D e ESI-MS. A degradação térmica dos lenhosulfonatos apresentou dois máximos de degradação a 188-190ºC e a 315-380ºC. As curvas de DSC mostraram um pico endotérmico para temperaturas inferiores a 130ºC e um pico exotérmico a 300-500ºC. Os lenhosulfonatos foram despolimerizados na presença de oxigénio molecular em meio alcalino. Os produtos de oxidação principais foram o aldeído siríngico, a vanilina, o ácido vanílico e o ácido siríngico. A adição do catalisador (sal de cobre) promoveu a oxidação dos lenhosulfonatos aumentando o rendimento dos aldeídos aromáticos (< 50%). A presença de açúcares nos lenhosulfonatos teve um efeito negativo no rendimento dos produtos de oxidação principais. Alguns compostos modelo dos produtos de oxidação dos lenhosulfonatos foram polimerizados por poliadição (catiónica e radicalar) e policondensação. Os monómeros e os polímeros foram caracterizados por espectroscopia de infravermelho de transformada de Fourier e reflectância total atenuada (FTIR-ATR), RMN em solução e no estado sólido, UV/Vis no estado sólido, GPC, difracção de raios-X (XRD), TGA e DSC. Os compostos modelo estudados foram os estirenos metoxi-substituídos (p-metoxiestireno e 3,4-dimetoxiestireno) e os ácidos hidroxi aromáticos metoxi-substituídos (ácido vanílico e ácido siríngico). O 3,4-dimetoxiestireno foi ainda copolimerizado com o éter isobutil vinílico e os seus copolímeros foram desmetilados, assim como, o poli(p-metoxiestireno) e o poli(3,4-dimetoxiestireno). A polimerização catiónica do p-metoxiestireno e 3,4-dimetoxiestireno é mais rápida e mais completa do que a polimerização radicalar produzindo polímeros com pesos moleculares elevados. O poli(p-metoxiestireno) (Mw = 235000 Da) possui um peso molecular maior do que o poli(3,4-dimetoxiestireno) (Mw = 18800 Da). A estabilidade térmica e a temperatura de transição vítrea diminuiram com a presença do segundo grupo metoxilo. A desmetilação dos homopolímeros foi bem sucedida, tendo sido corroborada por FTIR-ATR e RMN. A policondensação do ácido siríngico foi dificultada pela presença do segundo grupo metoxilo, tendo sido necessário adicionar uma maior quantidade do agente de condensação devido a factores estéricos. O poli(ácido vanílico) e poli(ácido siríngico) são insolúveis na maior parte dos solventes orgânicos, sendo parcialmente solúveis em clorofórmio, ácido triflúoracético, 1,1,2,2- tetracloroetano, dimetilsulfóxido, tetrahidrofurano, N,N’-dimetilformamida e 1,1,1,3,3,3-hexaflúor-2-propanol. A estabilidade térmica diminuiu com a presença do segundo grupo metoxilo e os dois polímeros não exibiram temperatura de transição vítrea. O poli(ácido vanílico) e poli(ácido siríngico) apresentaram uma estrutura muito cristalina (grau de cristalinidade 70% e 50%, respectivamente). O segundo grupo metoxilo aumentou o valor da absorvância, mas a forma do espectro de UV/Vis foi similar. A polimerização catiónica do éter isobutil vinílico resultou na produção de um polímero muito viscoso com peso molecular elevado (Mw = 20400 Da). A degradação térmica do polímero ocorreu em várias gamas de temperatura e foi completa (0% de resíduo a 800ºC). A copolimerização catiónica do 3,4-dimetoxiestireno com o éter isobutil vinílico foi realizada com proporções diferentes 80:20, 50:50 e 20:80. Os copolímeros apresentaram uma viscosidade elevada e um peso molecular baixo (Mw = 2000-4000 Da) que aumentou com a quantidade de éter isobutil vinílico. A degradação térmica dos copolímeros ocorreu também em várias gamas de temperatura, sendo a sua degradação completa (0,9-1,5% de resíduo a 800ºC). A desmetilação dos copolímeros não foi bem sucedida, tendo sido confirmada por FTIR-ATR e RMN.

Novos compostos orgânicos reticuláveis para aplicações em células fotovoltaicas

Trabalho Final de Mestrado para obtenção do grau de mestre em Engenharia Química e Biológica

Polyhydroxyalkanoates production by photosynthetic mixed cultures

Polyhydroxyalkanoates (PHAs) are natural biologically synthesized polymers that have been the subject of much interest in the last decades due to their biodegradability. Thus far, its microbial production is associated with high operational costs, which increases PHA prices and limits its marketability. To address this situation, this thesis’ work proposes the utilization of photosynthetic mixed cultures (PMC) as a new PHA production system that may lead to a reduction in operational costs. In fact, the operational strategies developed in this work led to the selection of PHA accumulating PMCs that, unlike the traditional mixed microbial cultures, do not require aeration, thus permitting savings in this significant operational cost. In particular, the first PHA accumulating PMC tested in this work was selected under non-aerated illuminated conditions in a feast and famine regime, being obtained a consortium of bacteria and algae, where photosynthetic bacteria accumulated PHA during the feast phase and consumed it for growth during the famine phase, using the oxygen produced by algae. In this symbiotic system, a maximum PHA content of 20% cell dry weight (cdw) was reached, proving for the first time, the capacity of a PMC to accumulate PHA. During adaptation to dark/light alternating conditions, the culture decreased its algae content but maintained its viability, achieving a PHA content of 30% cdw. Also, the PMC was found to be able to utilize different volatile fatty acids for PHA production, accumulating up to 20% cdw of a PHA co-polymer composed of 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (HV) monomers. Finally, a new selective approach for the enrichment of PMCs in PHA accumulating bacteria was tested. Instead of imposing a feast and famine regime, a permanent feast regime was used, thus selecting a PMC that was capable of simultaneously growing and accumulating PHA, being attained a maximum PHA content of 60% cdw, the highest value reported for a PMC thus far. The results presented in this thesis prospect the utilization of cheap, VFA-rich fermented wastes as substrates for PHA production, which combined with this new photosynthetic technology opens up the possibility for direct sunlight illumination, leading to a more cost-effective and environmentally sustainable PHA production process.

Effet de la microstructure sur les propriétés excitoniques des polymères semi-conducteurs semi-cristallins

Les polymères semi-conducteurs semicristallins sont utilisés au sein de diodes électroluminescentes, transistors ou dispositifs photovoltaïques organiques. Ces matériaux peuvent être traités à partir de solutions ou directement à partir de leur état solide et forment des agrégats moléculaires dont la morphologie dicte en grande partie leurs propriétés optoélectroniques. Le poly(3-hexylthiophène) est un des polymères semi-conducteurs les plus étudiés. Lorsque le poids moléculaire (Mw) des chaînes est inférieur à 50 kg/mol, la microstructure est polycristalline et composée de chaînes formant des empilements-π. Lorsque Mw>50 kg/mol, la morphologie est semicristalline et composée de domaines cristallins imbriquées dans une matrice de chaînes amorphes. À partir de techniques de spectroscopie en continu et ultrarapide et appuyé de modèles théoriques, nous démontrons que la cohérence spatiale des excitons dans ce matériau est légèrement anisotrope et dépend de Mw. Ceci nous permet d’approfondir la compréhension de la relation intime entre le couplage inter et intramoléculaire sur la forme spectrale en absorption et photoluminescence. De plus, nous démontrons que les excitations photogénérées directement aux interfaces entre les domaines cristallins et les régions amorphes génèrent des paires de polarons liés qui se recombinent par effet tunnel sur des échelles de temps supérieures à 10ns. Le taux de photoluminescence à long temps de vie provenant de ces paires de charges dépend aussi de Mw et varie entre ∼10% et ∼40% pour les faibles et hauts poids moléculaires respectivement. Nous fournissons un modèle permettant d’expliquer le processus de photogénération des paires de polarons et nous élucidons le rôle de la microstructure sur la dynamique de séparation et recombinaison de ces espèces.

Étude de dépendance des dynamiques de Polarons avec microstructures des semi-conducteurs polymériques

Cet ouvrage présente une étude portant sur le polymère P3EHT (poly(3-(20-ethyl)hexyl-thiophene)). Parmi les nombreuses caractéristiques de la dynamique des polarons pouvant être étudiées, seules celles liées aux changement de morphologie le seront dans ce travail. De plus, la vérification du modèle HJ permet d’expliquer la photophysique des polymères conjugués, grâce à l’étude des spectres de photoluminescence. L’étude de la dynamique des polarons à travers l’absorption photo-induite en fonction de la fréquence a permis de trouver les durées de vie pour un même échantillon avec des morphologies différentes. Les résultats ont démontré que la morphologie est non seulement fondamentale pour l’étude des polarons, mais consiste aussi en une caractéristique essentielle pour comprendre le nouveau modèle HJ.

Design de nouvelles fonctionnelles en théorie de la fonctionnelle de la densité et conception de polymères pour application à la photovoltaïque organique

La présente thèse porte sur les calculs utilisant la théorie de la fonctionnelle de la densité (DFT) pour simuler des systèmes dans lesquels les effets à longue portée sont importants. Une emphase particulière est mise sur les calculs des énergies d’excitations, tout particulièrement dans le cadre des applications photovoltaïques. Cette thèse aborde ces calculs sous deux angles. Tout d’abord, des outils DFT déjà bien établis seront utilisés pour simuler des systèmes d’intérêt expérimental. Par la suite, la théorie sous-jacente à la DFT sera explorée, ses limites seront identifiées et de nouveaux développements théoriques remédiant à ceux-ci seront proposés. Ainsi, dans la première partie de cette thèse, des calculs numériques utilisant la DFT et la théorie de la fonctionnelle de la densité dépendante du temps (TDDFT) telles qu’implémentées dans le logiciel Gaussian [1] sont faits avec des fonctionnelles courantes sur des molécules et des polymères d’intérêt expérimental. En particulier, le projet présenté dans le chapitre 2 explore l’utilisation de chaînes latérales pour optimiser les propriétés électroniques de polymères déjà couramment utilisés en photovoltaïque organique. Les résultats obtenus montrent qu’un choix judicieux de chaînes latérales permet de contrôler les propriétés électroniques de ces polymères et d’augmenter l’efficacité des cellules photovoltaïques les utilisant. Par la suite, le projet présenté dans le chapitre 3 utilise la TDDFT pour explorer les propriétés optiques de deux polymères, le poly-3-hexyl-thiophène (P3HT) et le poly-3-hexyl- sélénophène (P3HS), ainsi que leur mélange, dans le but d’appuyer les observations expérimentales indiquant la formation d’exciplexe dans ces derniers. Les calculs numériques effectués dans la première partie de cette thèse permettent de tirer plusieurs conclusions intéressantes, mais mettent également en évidence certaines limites de la DFT et de la TDDFT pour le traitement des états excités, dues au traitement approximatif de l’interaction coulombienne à longue portée. Ainsi, la deuxième partie de cette thèse revient aux fondements théoriques de la DFT. Plus précisément, dans le chapitre 4, une série de fonctionnelles modélisant plus précisément l’interaction coulombienne à longue portée grâce à une approche non-locale est élaborée. Ces fonctionnelles sont basées sur la WDA (weighted density approximation), qui est modifiée afin d’imposer plusieurs conditions exactes qui devraient être satisfaites par le trou d’échange. Ces fonctionnelles sont ensuite implémentées dans le logiciel Gaussian [1] et leurs performances sont évaluées grâce à des tests effectués sur une série de molécules et d’atomes. Les résultats obtenus indiquent que plusieurs de ces fonctionnelles donnent de meilleurs résultats que la WDA. De plus, ils permettrent de discuter de l’importance relative de satisfaire chacune des conditions exactes.

Comparison of Microwave and Electrical Properties Selected Conducting Polymers

Microwave properties of conductive polymers is crucial because of their wide areas of applications such as coating in reflector antennas, coating in electronic equipments, firequenry selective .surfaces, EMI materials, satellite communication links, microchip antennas, and medical applications. This work involves a comparative study of dielectric properties of selected conducting polymers such as polyaniline. poly(3,4-eth),lenedio.syt2iophene), polvthiophene, polvpvrrole. and pohparaphenylene diazomethine (PPDA) in microwave and DC,fields. The inicrowave properties such as dielectric constant, dielectric loss. absorption coefficient, heating coefficient, skin depth, and conductivity in the microwave frequency (S hand), and DC fields were compared. PEDOT and polccuiiline were found to exhibit excellent properties in DC field and microwave frequencies, which make thein potential materials in many of the alorenientioned applications

Development of Photorefractive Polymers: Evaluation of Photoconducting and Electro-optic Properties

This Thesis discussed molecules suitable for photorefractive effect. Out of the molecules studied, only one system was used to make photorefractive polymers system. Other molecules, especially, the electro-optic polymer, Poly(3-methacrloyl-1-(4'-nitro-4-azo-1'-phenyl)phenylalanine-co- methyl methacrylate) can be subjected to more detailed studies to explore the possibilities of using them for electro-optic applications. Though not included in the thesis, the efficient photoconductor, Poly(6-tert-butyl-3- phenyl-3,4-dihydro-2H-1,3-benzoxazine) sensitized with C60, which was described in Chapter 3 showed a low magnitude photovoltaic effect. This hints at the possibility of using this system for organic solar cells also. The thesis presented the initial observation of photorefractive effect in a polybenzoxazine based polymer system. A detailed analysis of the effect of C60, ECZ and DR1 can be carried out to check for the possibility of a high efficiency photorefractive system.

Gut microbiota modulate the metabolism of brown adipose tissue in mice

A two by two experimental study has been designed to determine the effect of gut microbiota on energy metabolism in mouse models. The metabolic phenotype of germ-free (GF, n = 20) and conventional (n = 20) mice was characterized using a NMR spectroscopy-based metabolic profiling approach, with a focus on sexual dimorphism (20 males, 20 females) and energy metabolism in urine, plasma, liver, and brown adipose tissue (BAT). Physiological data of age-matched GF and conventional mice showed that male animals had a higher weight than females in both groups. In addition, conventional males had a significantly higher total body fat content (TBFC) compared to conventional females, whereas this sexual dimorphism disappeared in GF animals (i.e., male GF mice had a TBFC similar to those of conventional and GF females). Profiling of BAT hydrophilic extracts revealed that sexual dimorphism in normal mice was absent in GF animals, which also displayed lower BAT lactate levels and higher levels of (D)-3-hydroxybutyrate in liver, plasma, and BAT, together with lower circulating levels of VLDL. These data indicate that the gut microbiota modulate the lipid metabolism in BAT, as the absence of gut microbiota stimulated both hepatic and BAT lipolysis while inhibiting lipogenesis. We also demonstrated that (1)H NMR metabolic profiles of BAT were excellent predictors of BW and TBFC, indicating the potential of BAT to fight against obesity.

Integrated cytokine and metabolic analysis of pathological responses to parasite exposure in rodents

Parasitic infections cause a myriad of responses in their mammalian hosts, on immune as well as on metabolic level. A multiplex panel of cytokines and metabolites derived from four parasite-rodent models, namely, Plasmodium berghei-mouse, Trypanosoma brucei brucei-mouse, Schistosoma mansoni-mouse, and Fasciola hepatica-rat were statistically coanalyzed. 1H NMR spectroscopy and multivariate statistical analysis were used to characterize the urine and plasma metabolite profiles in infected and noninfected animals. Each parasite generated a unique metabolic signature in the host. Plasma cytokine concentrations were obtained using the ‘Meso Scale Discovery’ multi cytokine assay platform. Multivariate data integration methods were subsequently used to elucidate the component of the metabolic signature which is associated with inflammation and to determine specific metabolic correlates with parasite-induced changes in plasma cytokine levels. For example, the relative levels of acetyl glycoproteins extracted from the plasma metabolite profile in the P. berghei-infected mice were statistically correlated with IFN-γ, whereas the same cytokine was anticorrelated with glucose levels. Both the metabolic and the cytokine data showed a similar spatial distribution in principal component analysis scores plots constructed for the combined murine data, with samples from all infected animals clustering according to the parasite species and whereby the protozoan infections (P. berghei and T. b. brucei) grouped separately from the helminth infection (S. mansoni). For S. mansoni, the main infection-responsive cytokines were IL-4 and IL-5, which covaried with lactate, choline, and D-3-hydroxybutyrate. This study demonstrates that the inherently differential immune response to single and multicellular parasites not only manifests in the cytokine expression, but also consequently imprints on the metabolic signature, and calls for in-depth analysis to further explore direct links between immune features and biochemical pathways.