Carbon isotope fractionation during calcium carbonate precipitation induced by urease-catalysed hydrolysis of urea

Stable carbon isotopic fractionation during calcium carbonate precipitation induced by urease-catalysed hydrolysis of urea was experimentally investigated in artificial water at a constant temperature of 30 degrees C. Carbon isotope fractionation during urea hydrolysis follows a Rayleigh distillation trend characterized by a C-13-enrichment factor of -20 to -22 parts per thousand. CaCO3 precipitate is up to 17.9 parts per thousand C-13-depleted relative to the urea substrate (-48.9 +/- 0.07 parts per thousand). Initial CaCO3 precipitate forms close to isotopic equilibrium with dissolved inorganic carbon. Subsequent precipitation occurs at -2 to -3 parts per thousand offset from isotopic equilibrium, suggesting that the initial delta C-13 value of CaCO3 is reset through dissolution followed by reprecipitation with urease molecules playing a role in offsetting the delta C-13 value of CaCO3 from isotopic equilibrium. Potentially, this isotopic systematics may provide a tool for the diagnosis of ureolytically-formed carbonate cements used as sealing agent. Moreover, it may serve as a basis to develop a carbon isotope tool for the quantification of ureolytically-induced CO2 sequestration. Finally, it suggests carbon isotope disequilibrium as a hallmark of past enzymatic activity in ancient microbial carbonate formation. (C) 2012 Elsevier B.V. All rights reserved.

Strontium zirconate heterogeneous catalyst for biodiesel production: Synthesis, characterization and catalytic activity evaluation

Strontium zirconate oxide was synthesized by co-precipitation and the citrate route and was evaluated as a heterogeneous catalyst for biodiesel production. The catalyst samples were characterized by XRD, FTIR, and TG, and catalytic activity was measured based on the ester content of the biodiesel produced that was quantified by GC. The co-precipitate samples were obtained in alkaline pH and had a mixture of the perovskite and pure strontium and zirconium oxide phases. Ester conversion using these samples was approximately 1.6%, indicating no catalytic activity. The citrate route was more efficient in producing perovskite when carried out at pH 7-8; excess SrCO3 was found on the catalyst surface due to CO2 adsorption, thus demonstrating no catalytic activity. The same synthesis carried out at pH 2 resulted in free OH- groups, with a small amount of the carbonate species that produced ester yield values of 98%. Therefore, matrices based on strontium zirconate produced via the citrate route in acidic media are potential heterogeneous catalysts for transesterification. (C) 2012 Elsevier B.V. All rights reserved.

Structural Refinement and Photoluminescence Properties of MnWO4 Nanorods Obtained by Microwave-Hydrothermal Synthesis

Manganese tungstate (MnWO4) nanorods were prepared at room temperature by the co-precipitation method and synthesized after processing in a microwave-hydrothermal (MH) system at 140 degrees C for 6-96 min. These nanorods were structurally characterized by X-ray diffraction (XRD), Rietveld refinements and Fourier transform (FT)-Raman spectroscopy. The growth direction, shape and average size distribution of nanorods were observed by means of transmission electron microscopy (TEM) and high resolution TEM (HR-TEM). The optical properties of the nanorods were investigated by ultraviolet visible (UV-vis) absorption and photoluminescence (PL) measurements. XRD patterns, Rietveld refinement data and FT-Raman spectroscopy indicate that the MnWO4 precipitate is not a single phase structure while the nanorods synthesized by MH processing have a wolframite-type monoclinic structure without deleterious phases. FT-Raman spectra exhibited the presence of 17 Raman-active modes from 50 to 1,000 cm(-1). TEM and HR-TEM micrographs indicated that the nanorods are aggregated due to surface energy by Van der Waals forces and grow along the [100] direction. UV-vis absorption measurements confirmed non-linear values for the optical band gap (from 3.2 to 2.72 eV), which increased as the MH processing time increased. The structural characterizations indicated that the presence of defects in the MnWO4 precipitate promotes a significant contribution to maximum PL emission, while MnWO4 nanorods obtained by MH processing decrease the PL emission due to the reduction of defects in the lattice.

La política económica, la construcción de vivienda y la producción de la ciudad en España (1939-75)

[ES] La construcción de la ciudad y la edificación de viviendas en España han estado condicionadas, entre otros factores, por las características estructurales y coyunturales del sector de la construcción y por las diferentes políticas económicas desarrolladas. El objetivo de esta aportación se centra en el análisis de la acción política puesta en marcha en España durante el franquismo (1939-75), en la caracterización del sector constructor-promotor y en el estudio de las repercusiones en el crecimiento inmobiliario y de la ciudad, centrándonos de un modo más específico en el caso de Canarias, dadas las peculiaridades que presentan las Islas en el contexto español. Al contrario de lo que suele afirmarse, se defiende que el precipitado proceso de conformación de la ciudad a partir de la década de los sesenta no sólo se debe al desarrollo de un modelo económico desarrollista, sino también a la profunda huella que el periodo autárquico había dejado en la economía y en la sociedad española. 

Morphological and functional study of cerebral aging in rat

Aging is a physiological process characterized by a progressive decline of the “cellular homeostatic reserve”, refereed as the capability to respond suitably to exogenous and endogenous stressful stimuli. Due to their high energetic requests and post-mitotic nature, neurons are peculiarly susceptible to this phenomenon. However, the aged brain maintains a certain level of adaptive capacities and if properly stimulated may warrant a considerable functional recovery. Aim of the present research was to verify the plastic potentialities of the aging brain of rats subjected to two kind of exogenous stimuli: A) the replacement of the standard diet with a ketogenic regimen (the change forces the brain to use ketone bodies (KB) in alternative to glucose to satisfy the energetic needs) and B) a behavioural task able to induce the formation of inhibitory avoidance memory. A) Fifteen male Wistar rats of 19 months of age were divided into three groups (average body weight pair-matched), and fed for 8 weeks with different dietary regimens: i) diet containing 10% medium chain triglycerides (MCT); ii) diet containing 20% MCT; iii) standard commercial chow. Five young (5 months of age) and five old (26-27 months of age) animals fed with the standard diet were used as further controls. The following morphological parameters reflecting synaptic plasticity were evaluated in the stratum moleculare of the hippocampal CA1 region (SM CA1), in the outer molecular layer of the hippocampal dentate gyrus (OML DG), and in the granule cell layer of the cerebellar cortex (GCL-CCx): average area (S), numeric density (Nvs), and surface density (Sv) of synapses, and average volume (V), numeric density (Nvm), and volume density (Vv) of synaptic mitochondria. Moreover, succinic dehydrogenase (SDH) activity was cytochemically determined in Purkinje cells (PC) and V, Nvm, Vv, and cytochemical precipitate area/mitochondrial area (R) of SDH-positive mitochondria were evaluated. In SM CA1, MCT-KDs induced the early appearance of the morphological patterns typical of old animals: higher S and V, and lower Nvs and Nvm. On the contrary, in OML DG, Sv and Vv of MCT-KDs-fed rats were higher (as a result of higher Nvs and Nvm) vs. controls; these modifications are known to improve synaptic function and metabolic supply. The opposite effects of MCT-KDs might reflect the different susceptibility of these brain regions to the aging processes: OML DG is less vulnerable than SM CA1, and the reactivation of ketone bodies uptake and catabolism might occur more efficiently in this region, allowing the exploitation of their peculiar metabolic properties. In GCL-CCx, the results described a new scenario in comparison to that found in the hippocampal formation: 10%MCT-KD induced the early appearance of senescent patterns (decreased Nvs and Nvm; increased V), whereas 20%MCT-KD caused no changes. Since GCL-CCx is more vulnerable to age than DG, and less than CA1, these data further support the hypothesis that MCT-KDs effects in the aging brain critically depend on neuronal vulnerability to age, besides MCT percentage. Regarding PC, it was decided to evaluate only the metabolic effect of the dietetic regimen (20%MCT-KD) characterized by less side effects. KD counteracted age-related decrease in numeric density of SDH-positive mitochondria, and enhanced their energetic efficiency (R was significantly higher in MCT-KD-fed rats vs. all the controls). Since it is well known that Purkinje and dentate gyrus cells are less vulnerable to aging than CA1 neurons, these results corroborate our previous hypothesis. In conclusion, the A) experimental line provides the first evidence that morphological and functional parameters reflecting synaptic plasticity and mitochondrial metabolic competence may be modulated by MCT-KDs in the pre-senescent central nervous system, and that the effects may be heterogeneous in different brain regions. MCT-KDs seem to supply high energy metabolic intermediates and to be beneficial (“anti-aging”) for those neurons that maintain the capability to exploit them. This implies risks but also promising potentialities for the therapeutic use of these diets during aging B) Morphological parameters of synapses and synaptic mitochondria in SM CA1 were investigated in old (26-27 month-old) female Wistar rats following a single trial inhibitory avoidance task. In this memory protocol animals learn to avoid a dark compartment in which they received a mild, inescapable foot-shock. Rats were tested 3 and 6 or 9 hours after the training, divided into good and bad responders according to their performance (retention times above or below 100 s, respectively) and immediately sacrificed. Nvs, S, Sv, Nvm, V, and Vv were evaluated. In the good responder group, the numeric density of synapses and mitochondria was significantly higher and the average mitochondrial volume was significantly smaller 9 hours vs. 6 hours after the training. No significant differences were observed among bad responders. Thus, better performances in passive avoidance memory task are correlated with more efficient plastic remodeling of synaptic contacts and mitochondria in hippocampal CA1. These findings indicate that maintenance of synaptic plastic reactivity during aging is a critical requirement for preserving long-term memory consolidation.

Preparation of new crystal forms via photochemical, mechanochemical and sol-gel methods

This work of thesis involves various aspects of crystal engineering. Chapter 1 focuses on crystals containing crown ether complexes. Aspects such as the possibility of preparing these materials by non-solution methods, i.e. by direct reaction of the solid components, thermal behavior and also isomorphism and interconversion between hydrates are taken into account. In chapter 2 a study is presented aimed to understanding the relationship between hydrogen bonding capability and shape of the building blocks chosen to construct crystals. The focus is on the control exerted by shape on the organization of sandwich cations such as cobalticinium, decamethylcobalticinium and bisbenzenchromium(I) and on the aggregation of monoanions all containing carboxylic and carboxylate groups, into 0-D, 1-D, 2-D and 3-D networks. Reactions conducted in multi-component molecular assemblies or co-crystals have been recognized as a way to control reactivity in the solid state. The [2+2] photodimerization of olefins is a successful demonstration of how templated solid state synthesis can efficiently synthesize unique materials with remarkable stereoselectivity and under environment-friendly conditions. A demonstration of this synthetic strategy is given in chapter 3. The combination of various types of intermolecular linkages, leading to formation of high order aggregation and crystalline materials or to a random aggregation resulting in an amorphous precipitate, may not go to completeness. In such rare cases an aggregation process intermediate between crystalline and amorphous materials is observed, resulting in the formation of a gel, i.e. a viscoelastic solid-like or liquid-like material. In chapter 4 design of new Low Molecular Weight Gelators is presented. Aspects such as the relationships between molecular structure, crystal packing and gelation properties and the application of this kind of gels as a medium for crystal growth of organic molecules, such as APIs, are also discussed.

Il Senato come camera di rappresentanza territoriale

La riforma del bicameralismo rappresenta nell’ordinamento italiano una delle tematiche più dibattute sin dalla “concessione” dello Statuto Albertino. In Assemblea Costituente, infatti, l’opzione tra monocamerali e bicameralismo - prima - e il dibattito su che tipo di bicameralismo si sarebbe dovuto adottare - poi - hanno dato vita ad una parte organizzativa particolarmente debole e in gran parte antiquata rispetto alle esigenze della prima parte della Costituzione che, al contrario, ha rappresentato il precipitato di una profonda consonanza di ideali. La tesi si propone dunque l’obiettivo di dimostrare che l’esigenza di procedere ad una riforma del sistema bicamerale in Italia sia oggi quanto mai attuale e necessaria. Da un lato, infatti, essa favorirebbe il superamento delle inefficienze del sistema parlamentare e potrebbe rappresentare uno strumento per ovviare alla debole razionalizzazione della forma di governo che, da sempre, ha determinato la strutturale instabilità degli esecutivi. Dall’altro lato, la riforma servirebbe soprattutto a realizzare quella connessione organica tra Stato e regioni necessaria per completare il disegno regionalistico che si ricava dalla Costituzione stessa. Esigenza questa che, peraltro, si è notevolmente rafforzata con la riforma del titolo V della Costituzione, la cui portata innovativa è stata sostanzialmente svuotata di contenuto a causa delle difficoltà che si sono incontrate nella sua attuazione.

Lichtsammler hinter Glas : Stabilisierung und Funktionalisierung des pflanzlichen Hauptlichtsammelkomplexes (LHCII) durch biomineralische Einbettung in Nanopartikel

Der Haupt-Lichtsammelkomplex des Fotosystems II (LHCII) setzt sich aus einem Proteinanteil und nicht-kovalent gebundenen Pigmenten – 8 Chlorophyll a, 6 Chlorophyll b und 4 Carotinoide - zusammen. Er assembliert in vivo zu einem Trimer, in dem die Monomereinheiten ebenfalls nicht-kovalent miteinander wechselwirken. Die ausgesprochen hohe Farbstoffdichte und die Tatsache, dass der Komplex rekombinant hergestellt werden kann, machen den LHCII zu einem interessanten Kandidaten für technische Anwendungen wie einer Farbstoffsolarzelle. Allerdings muss hierzu seine thermische Stabilität drastisch erhöht werden.rnDer Einschluss von Proteinen/Enzymen in Silikat erhöht deren Stabilität gegenüber Hitze signifikant. LHCII sollte als erster rekombinanter Membranproteinkomplex mittels kovalent verbundener, polykationischen Sequenzen in Silikat eingeschlossen werden. Hierzu wurde der Komplex auf zwei Weisen polykationisch modifiziert: Auf Genebene wurde die Sequenz des R5-Peptids in den N-terminalen Bereich des LHCP-Gens eingeführt und ein Protokoll zur Überexpression, Rekonstitution und Trimerisierung etabliert. Außerdem wurde eine kovalente Modifikation des trimeren LHCII mit dem Arginin-reichen Protamin über heterobifunktionelle Crosslinker entwickelt. Beide resultierenden LHCII-Derivate waren in der Lage, Silikat autogen zu fällen. Die Stabilisierung der so in Silikat präzipitierten Komplexe war jedoch deutlich geringer als bei nicht-modifizierten Komplexen, die durch eine Spermin-induzierte Copräzipitation eingeschlossenen wurden. Dabei zeigte sich, dass für den Anteil der eingebauten Komplexe und das Ausmaß an Stabilisierung die Größe und klare partikuläre Struktur des Silikats entscheidend ist. Kleine Partikel mit einem Durchmesser von etwa 20 nm führten zu einem Einbau von rund 75 % der Komplexe, und mehr als 80 % des Energietransfers innerhalb des Komplexes blieben erhalten, wenn für 24 Stunden bei 50°C inkubiert wurde. Nicht in Silikat eingeschlossene Komplexe verloren bei 50°C ihren Komplex-internen Energietransfer binnen weniger Minuten. Es war dabei unerheblich, ob die Partikelgröße durch die Wahl des Puffers und des entsprechenden pH-Wertes, oder aber durch Variation des Spermin-zu-Kieselsäure-Verhältnisses erreicht wurde. Wurden die polykationisch veränderten Komplexe in solchen Copräzipitationen verwendet, so erhöhte sich der Anteil an eingebauten Komplexen auf über 90 %, jedoch wurde nur bei der R5-modifizierten Variante vergleichbare Ausmaße an Stabilisierung erreicht. Ein noch höherer Anteil an Komplexen wurde in das Silikatpellet eingebaut, wenn LHCII kovalent mit Silanolgruppen modifiziert wurde (95 %); jedoch war das Ausmaß der Stabilisierung wiederum geringer als bei einer Copräzipitation. Die analysierten Fällungssysteme waren außerdem in der Lage, Titandioxid zu fällen, wobei der Komplex in dieses eingebaut wurde. Allerdings muss das Stabilisierungspotential hier noch untersucht werden. Innerhalb eines Silikatpräzipitats aggregierten die Komplexe nicht, zeigten aber einen inter-trimeren Energietransfer, der sehr wahrscheinlich auf einem Förster Resonanz Mechanismus basiert. rnDies und das hohe Maß an Stabilisierung eröffnen neue Möglichkeiten, rekombinanten LHCII in technischen Applikationen als Lichtsammelkomponente zu verwenden.rn

Processing and Composition Effects on the Fracture Behavior of Spray-Formed 7XXX Series Al Alloys

The fracture properties of high-strength spray-formed Al alloys were investigated, with consideration of the effects of elemental additions such as zinc,manganese, and chromium and the influence of the addition of SiC particulate. Fracture resistance values between 13.6 and 25.6 MPa (m)1/2 were obtained for the monolithic alloys in the T6 and T7 conditions, respectively. The alloys with SiC particulate compared well and achieved fracture resistance values between 18.7 and 25.6 MPa (m)1/2. The spray-formed materials exhibited a loss in fracture resistance (KI) compared to ingot metallurgy 7075 alloys but had an improvedperformance compared to high-solute powder metallurgy alloys of similar composition. Characterization of the fracture surfaces indicated a predominantly intergranular decohesion, possibly facilitated by the presence of incoherent particles at the grain boundary regions and by the large strength differentialbetween the matrix and precipitate zone. It is believed that at the slip band-grain boundary intersection, particularly in the presence of large dispersoids and/or inclusions, microvoid nucleation would be significantly enhanced. Differences in fracture surfaces between the alloys in the T6 and T7 condition were observed and are attributed to inhomogeneous slip distribution, which results in strain localization at grain boundaries. The best overall combination of fracture resistance properties were obtained for alloys with minimum amounts of chromium and manganese additions.

Health, Justice, and Fairness

In this study I will endeavor to show that the American system of health care violates any conception of distributive justice understood as equality of opportunity. This system fails to provide equal access through a lack of universal insurance, a consumer driven conception of quality, and a system wide focus on cost control, leaving millions of Americans exposed to the ravages of disease. However, if health is understood as an antecedent for one's ability to function across a number of categories that have been objectively deemed as vital to engage in a life that is fully human than the commitment our nation has to the protection of fair equality of opportunity, established by our adoption of a Rawlsian conception of justice, necessitates a revision of our nation's conception of quality to encapsulate health outcomes as well as the advent of a system of universal coverage. Quality care will come to be understood as care that returns to the patient the ability to function across those categories of functioning that illness has jeopardized, and this conception of quality will precipitate system wide reform geared at the creation of positive health outcomes. This paper will articulate this argument by reconstructing and synthesizing precepts from the contemporary philosophical sources and then applying these to the practical workings of our healthcare system, while concurrently demonstrating that a system of distributive justice is compatible with the creation of a universal system of healthcare.

Adsorption behavior of redox-active suppressor additives: Combined electrochemical and STM studies

The redox chemistry and the related surface phase behavior of Safranine (SAF) and Janus Green B (JGB) have been studied by means of cyclic voltammetry in combination with in situ Scanning Tunneling Microscopy using HOPG (Highly Oriented Pyrolytic Graphite) and single crystalline Cu(1 0 0) as model substrates, both revealing different widths of the accessible potential windows. JGB and SAF serve as prototypical heterocyclic suppressor/leveler additives that are used for the metallization of 3D-TSVs (3D Through Silicon Vias) following a classical "leveling" concept. SAF can be considered as the reductive decomposition product of JGB that is formed at the copper/electrolyte interface upon electroplating. Both additives reveal a pronounced pH-dependent redox-chemistry with redox-transitions lying close to or even beyond the anodic limit of the copper potential window. Affected by these redox-processes are in particular the aromatic cores of those heterocycles that can be (quasi)reversibly reduced by a two electron transfer process within the potential window of copper. Therefore we identify the reduced form of those dyes as the active components for the suppressing/leveling effect in copper plating. STM data clearly shows a dye surface phase behavior that is crucially determined by its potential-dependent redox-chemistry. This will be exemplarily discussed for the SAF dye. On chloride-modified Cu(1 0 0) mono-reduced SAF forms a structurally well-defined monolayer of cationic stacking polymers. However, this coupled anion/cation layer reveals only minor suppressing capabilities with respect to the copper dissolution and deposition processes. Complete reduction of the aromatic heterocycle finally leads to the 3D precipitation of hydrophobic reaction products. 3D clusters of this SAF precipitate are discussed as the active structural motif for the suppressing effect of these dyes. (C) 2011 Elsevier Ltd. All rights reserved.

Nutrition in clinical practice-the refeeding syndrome: illustrative cases and guidelines for prevention and treatment

The refeeding syndrome is a potentially lethal complication of refeeding in patients who are severely malnourished from whatever cause. Too rapid refeeding, particularly with carbohydrate may precipitate a number of metabolic and pathophysiological complications, which may adversely affect the cardiac, respiratory, haematological, hepatic and neuromuscular systems leading to clinical complications and even death. We aimed to review the development of the refeeding syndrome in a variety of situations and, from this and the literature, devise guidelines to prevent and treat the condition. We report seven cases illustrating different aspects of the refeeding syndrome and the measures used to treat it. The specific complications encountered, their physiological mechanisms, identification of patients at risk, and prevention and treatment are discussed. Each case developed one or more of the features of the refeeding syndrome including deficiencies and low plasma levels of potassium, phosphate, magnesium and thiamine combined with salt and water retention. These responded to specific interventions. In most cases, these abnormalities could have been anticipated and prevented. The main features of the refeeding syndrome are described with a protocol to anticipate, prevent and treat the condition in adults.

Regulation of human liver delta-aminolevulinic acid synthase by bile acids

Aminolevulinic acid synthase 1 (ALAS1) is the rate-limiting enzyme of heme synthesis in the liver and is highly regulated to adapt to the metabolic demand of the hepatocyte. In the present study, we describe human hepatic ALAS1 as a new direct target of the bile acid-activated nuclear receptor farnesoid X receptor (FXR). Experiments in primary human hepatocytes and in human liver slices showed that ALAS1 messenger RNA (mRNA) and activity is increased upon exposure to chenodeoxycholic acid (CDCA), the most potent natural FXR ligand, or the synthetic FXR-specific agonist GW4064. Moreover, overexpression of a constitutively active form of FXR further increased ALAS1 mRNA expression. In agreement with these observations, an FXR response element was identified in the 5' flanking region of human ALAS1 and characterized in reporter gene assays. A highly conserved FXR binding site (IR1) within a 175-bp fragment at -13 kilobases upstream of the transcriptional start site was able to trigger an FXR-specific increase in luciferase activity upon CDCA treatment. Site-directed mutagenesis of IR1 abolished this effect. Binding of FXR/retinoid acid X receptor heterodimers was demonstrated by mobility gel shift experiments. Conclusion: These data strongly support a role of bile acid-activated FXR in the regulation of human ALAS1 and, consequently, hepatic porphyrin and heme synthesis. These data also suggest that elevated endogenous bile acids may precipitate neuropsychiatric attacks in patients with acute hepatic porphyrias.

CHARACTERIZATION OF ASPHALT MATERIALS CONTAINING BIO OIL FROM MICHIGAN WOOD

The objective of this research is to develop sustainable wood-blend bioasphalt and characterize the atomic, molecular and bulk-scale behavior necessary to produce advanced asphalt paving mixtures. Bioasphalt was manufactured from Aspen, Basswood, Red Maple, Balsam, Maple, Pine, Beech and Magnolia wood via a 25 KWt fast-pyrolysis plant at 500 °C and refined into two distinct end forms - non-treated (5.54% moisture) and treated bioasphalt (1% moisture). Michigan petroleum-based asphalt, Performance Grade (PG) 58-28 was modified with 2, 5 and 10% of the bioasphalt by weight of base asphalt and characterized with the gas chromatography-mass spectroscopy (GC-MS), Fourier Transform Infra-red (FTIR) spectroscopy and the automated flocculation titrimetry techniques. The GC-MS method was used to characterize the Carbon-Hydrogen-Nitrogen (CHN) elemental ratio whiles the FTIR and the AFT were used to characterize the oxidative aging performance and the solubility parameters, respectively. For rheological characterization, the rotational viscosity, dynamic shear modulus and flexural bending methods are used in evaluating the low, intermediate and high temperature performance of the bio-modified asphalt materials. 54 5E3 (maximum of 3 million expected equivalent standard axle traffic loads) asphalt paving mixes were then prepared and characterized to investigate their laboratory permanent deformation, dynamic mix stiffness, moisture susceptibility, workability and constructability performance. From the research investigations, it was concluded that: 1) levo, 2, 6 dimethoxyphenol, 2 methoxy 4 vinylphenol, 2 methyl 1-2 cyclopentandione and 4-allyl-2, 6 dimetoxyphenol are the dominant chemical functional groups; 2) bioasphalt increases the viscosity and dynamic shear modulus of traditional asphalt binders; 3) Bio-modified petroleum asphalt can provide low-temperature cracking resistance benefits at -18 °C but is susceptible to cracking at -24 °C; 3) Carbonyl and sulphoxide oxidation in petroleum-based asphalt increases with increasing bioasphalt modifiers; 4) bioasphalt causes the asphaltene fractions in petroleum-based asphalt to precipitate out of the solvent maltene fractions; 5) there is no definite improvement or decline in the dynamic mix behavior of bio-modified mixes at low temperatures; 6) bio-modified asphalt mixes exhibit better rutting performance than traditional asphalt mixes; 7) bio-modified asphalt mixes have lower susceptibility to moisture damage; 8) more field compaction energy is needed to compact bio-modified mixes.

The Effect of the Fe2: Fe3 Ratio upon the Current Efficiency in the Electrolysis of a Copper Sulfate Solution Containing Iron Sulfate

In the treatment of copper ores by hydro-electro-metallurgical methods, not only is copper deposited, but other metals are also dissolved. In practice it has been found* that iron, under certain conditions, causes the copper to deposit on the cathode as a nonadherent precipitate and also that the iron in solution causes a great decrease in current efficiency, es­pecially when the electrolysis is conducted by operating with a higher current density at the cathode than at the anode. The present investigation deals with the effects of the two valences of iron on the current efficiency and endeavors to determine whether or not there is a ratio of the two at which point the efficiency becomes zero or approaches it.