A kinetic investigation of thermal degradation of poly(vinyl formals)

Several samples of poly(vinyl formal) having the same vinyl alcohol content (8–9%) but varying contents of vinyl acetate (6–22%) and vinyl formol (70–85%) were prepared and subjected to thermogravimetric analysis, in air and nitrogen atmospheres, employing both isothermal and dynamic methods. Kinetic parameters determined from both the isothermal and dynamic TGA data are compared. The activation energy is seen to be largely dependent on the degree of conversion, implying a complex degradation reaction. The activation energy is also much less for degradation in air than in nitrogen, which can be explained by a reaction with oxygen-producing structures favoring degradation. The activation energy is less sensitive to variation in polymer composition for degradation in air than in nitrogen. Thus, in the dynamic process, the activation energy value decreases (from 36 to 23 kcal/mole) with increasing acetate content (from 6 to 22%) in nitrogen atmosphere, while in air the activation energy value increases only moderately (from 21 to 27 kcal/mole) with increasing acetate content (from 6 to 22%). The order of reaction is nearly unity, irrespective of the composition of the polymer, both in air and nitrogen.

A kinetic investigation of thermal degradation of poly(vinyl formals)

Several samples of poly(vinyl formal) having the same vinyl alcohol content (8–9%) but varying contents of vinyl acetate (6–22%) and vinyl formol (70–85%) were prepared and subjected to thermogravimetric analysis, in air and nitrogen atmospheres, employing both isothermal and dynamic methods. Kinetic parameters determined from both the isothermal and dynamic TGA data are compared. The activation energy is seen to be largely dependent on the degree of conversion, implying a complex degradation reaction. The activation energy is also much less for degradation in air than in nitrogen, which can be explained by a reaction with oxygen-producing structures favoring degradation. The activation energy is less sensitive to variation in polymer composition for degradation in air than in nitrogen. Thus, in the dynamic process, the activation energy value decreases (from 36 to 23 kcal/mole) with increasing acetate content (from 6 to 22%) in nitrogen atmosphere, while in air the activation energy value increases only moderately (from 21 to 27 kcal/mole) with increasing acetate content (from 6 to 22%). The order of reaction is nearly unity, irrespective of the composition of the polymer, both in air and nitrogen.

Mesoporous Carbon and Poly(3,4-ethylenedioxythiophene) Composite as Catalyst Support for Polymer Electrolyte Fuel Cells

In situ polymerization of 3,4-ethylenedioxythiophene with sol-gel-derived mesoporous carbon (MC) leading to a new composite and its subsequent impregnation with Pt nanoparticles for application in polymer electrolyte fuel cells (PEFCs) is reported. The composite exhibits good dispersion and utilization of platinum nanoparticles akin to other commonly used microporous carbon materials, such as carbon black. Pt-supported MC-poly(3,4-ethylenedioxythiophene) (PEDOT) composite also exhibits promising electrocatalytic activity toward oxygen reduction reaction, which is central to PEFCs. The PEFC with Pt-loaded MC-PEDOT support exhibits 75% of enhancement in its power density in relation to the PEFC with Pt-loaded pristine MC support while operating under identical conditions. It is conjectured that Pt-supported MC-PEDOT composite ameliorates PEFC performance/durability on repetitive potential cycling. (C) 2010 The Electrochemical Society. DOI: 10.1149/1.3486172] All rights reserved.

Estimation Of Charge Transport Parameters And Equivalent Circuit For Poly Alkyl Thiophene Field-Effect Transistors

The small signal ac response is measured across the source-drain terminals of organic field-effect transistors (OFET) under dc bias to obtain the equivalent circuit parameters of poly(2,5-bis(3-tetradecylthiophen-2-yl)thieno[3,2-b]thiophene) (PBTTT) and poly(3-hexyl thiophene) (P3HT) based devices. The numerically simulated response based on these parameters is in good agreement with the experimental data for PBTTT-FET except at low frequencies, while the P3HT-FET data show significant deviations. This indicates that the interface with the metal electrode is rather complex for the latter, involving additional circuit elements arising from contact impedance or charge injection processes. Such an investigation can help in identifying the operational bottlenecks and to improve the performance of OFETs.

Interactions of tris buffer with nucleotides: the crystal structure of tris(hydroxymethyl)methylammonium adenosine 5'-diphosphate dihydrate

The crystal and molecular structures of the Tris salt of adenosine 5'-diphosphate were determined from X-ray diffraction data. The crystals are monoclinic, space P21, and Z = 2 with a=9.198 (2) A, b=6.894 (1) A, c=18.440 (4) A, and beta = 92.55 (2) degrees. Intensity data were collected on an automated diffractometer. The structure was solved by the heavy-atom technique and refined by least squares to R = 0.047. The ADP molecule adopts a folded conformation. The conformation about the glycosidic bond is anti. The conformation of the ribose ring is close to a perfect C(2')-endo-C-(3')-exo puckering. The conformation about C(4')-C(5') is gauche-gauche, similar to other nucleotide structures. The pyrophosphate chain displays a nearly eclipsed geometry when viewed down the P-P vector, unlike the staggered conformation observed in crystal structures of other pyrophosphates. The less favorable eclipsed conformation probably results from the observed association of Tris molecules with the polar diphosphate chain through electrostatic interactions and hydrogen bonds. Such interactions may play an important role in Tris-buffered aqueous solutions of nucleotides and metal ions.

Chemical toughening of epoxies. I. Structural modification of epoxy resins by reaction with hydroxy-terminated poly (butadiene-co-acrylonitrile)

In an attempt to toughen the epoxy resin matrix for fiber-reinforced composite applications, a chemical modification procedure of a commercially available bisphenol-A-based epoxy resin using reactive liquid rubber HTBN [hydroxy-terminated poly(butadiene-co-acrylonitrile)] and TDI (tolylene diisocyanate) is described. The progress of the reaction and the structural changes during modification process are studied using IR spectroscopy, viscosity data, and chemical analysis (epoxy value determination). The studies support the proposition that TDI acts as a coupling agent between the epoxy and HTBN, forming a urethane linkage with the former and an oxazolidone ring with the latter. The chemical reactions that possibly take place during the modification are discussed.

Kinetics of sono-photooxidative degradation of poly(alkyl methacrylate)s

The mechano-chemical degradation of poly(methyl methacrylate) (PMMA), poly(ethyl methacrylate) (PEMA) and poly(n-butyl methacrylate) (PBMA) using ultrasound (US), ultraviolet (UV) radiation and a photoinitiator (benzoin) has been investigated. The degradation of the polymers was monitored using the reduction in number average molecular weight (M-n) and polydispersity (PDI). A degradation mechanism that included the decomposition of the initiator, generation of polymer radicals by the hydrogen abstraction of initiator radicals, reversible chain transfer between stable polymer and polymer radicals was proposed. The mechanism assumed mid-point chain scission due to US and random scission due to UV radiation. A series of experiments with different initial M-n of the polymers were performed and the results indicated that, irrespective of the initial PDI, the PDI during the sono-photooxidative degradation evolved to a steady state value of 1.6 +/- 0.05 for all the polymers. This steady state evolution of PDI was successfully predicted by the continuous distribution kinetics model. The rate coefficients of polymer scission due to US and UV exhibited a linear increase and decrease with the size of the alkyl group of the poly(alkyl methacrylate)s, respectively. (C) 2010 Elsevier B.V. All rights reserved.

Chemical toughening of epoxies. II. Mechanical, thermal, and microscopic studies of epoxies toughened with hydroxyl-terminated poly(butadiene-co-acrylonitrile)

Diglycidyl ether–bisphenol-A-based epoxies toughened with various levels (0–12%) of chemically reacted liquid rubber, hydroxyl-terminated poly(butadiene-co-acrylonitrile) (HTBN) were studied for some of the mechanical and thermal properties. Although the ultimate tensile strength showed a continuous decrease with increasing rubber content, the toughness as measured by the area under the stress-vs.-strain curve and flexural strength reach a maximum around an optimum rubber concentration of 3% before decreasing. Tensile modulus was found to increase for concentrations below 6%. The glass transition temperature Tg as measured by DTA showed no variation for the toughened formulations. The TGA showed no variations in the pattern of decomposition. The weight losses for the toughened epoxies at elevated temperatures compare well with that of the neat epoxy. Scanning electron microscopy revealed the presence of a dual phase morphology with the spherical rubber particles precipitating out in the cured resin with diameter varying between 0.33 and 6.3 μm. In contrast, a physically blended rubber–epoxy showed much less effect towards toughening with the precipitated rubber particles of much bigger diameter (0.6–21.3 μm).

Chemical toughening of epoxies. I. Structural modification of epoxy resins by reaction with hydroxy-terminated poly(butadiene-co-acrylonitrile)

In an attempt to toughen the epoxy resin matrix for fiber-reinforced composite applications, a chemical modification procedure of a commercially available bisphenol-A-based epoxy resin using reactive liquid rubber HTBN [hydroxy-terminated poly(butadiene-co-acrylonitrile)] and TDI (tolylene diisocyanate) is described. The progress of the reaction and the structural changes during modification process are studied using IR spectroscopy, viscosity data, and chemical analysis (epoxy value determination). The studies support the proposition that TDI acts as a coupling agent between the epoxy and HTBN, forming a urethane linkage with the former and an oxazolidone ring with the latter. The chemical reactions that possibly take place during the modification are discussed.

Characterization of poly- and monoclonal antibodies to physalis mottle (tymo) virus

Polyclonal antibodies were raised against the Physalis mottle virus (PhMV) and its denatured coat protein (PhMV-P). Analysis of the reactivity of the polyclonal antibodies with tryptic peptides of PhMV-P in dot-blot assays revealed that many of the epitopes were common to intact virus and denatured coat protein. Five monoclonal antibodies to the intact virus were obtained using hybridoma technology. These monoclonal antibodies reacted well with the denatured coat protein. Epitope analysis suggested that probably these monoclonal antibodies recognize overlapping epitopes. This was substantiated by epitope mapping using the CNBr digest of PhMV-P in western blots. All the five monoclonals recognized the N-terminal 15 K fragment. Attempts to further delineate the specific region recognized by the monoclonals by various enzymatic cleavages resulted in the loss of reactivity in all the cases. The results indicate that these monoclonals probably recognize epitopes within the N-terminal 15 K fragment of the coat protein.

Inverse relationship of the dehydrogenase and ADP-ribosylation activities in sodium-nitroprusside-treated glyceraldehyde-3-phosphate dehydrogenase is coincidental

Incubation of glyceraldehyde-3-phosphate dehydrogenase (GAPD) with sodium nitroprusside (SNP) decreased its activity in concentration- and time-dependent fashion in the presence of a thiol compounds, with DTT being more effective than GSH. Both forward and backward reactions were effected. Coinciding with this, HgCl2-sensitive labelling of the protein by [32P]NAD+ also increased, indicating the stimulation of ADP-ribosylation. Treatment with SNP of GAPD samples from rabbit muscle, sheep brain and yeast inactivated the dehydrogenase activity of the three, but only the mammalian proteins showed ADP-ribosylation activity. The SNP-modified protein of rabbit muscle GAPD, freed from the reagent by Sephadex filtration showed a concentration-dependent restoration of the dehydrogenase activity on preincubation with DTT and GSH. Such thiol-treated preparations also gave increased ADP-ribosylation activity with DTT, and to a lesser extent with GSH. The SNP-modified protein was unable to catalyze this activity with the native yeast enzyme and native and heat-inactivated muscle enzyme. It was possible to generate the ADP-ribosylation activity in muscle GAPD, by an NO-independent mechanism, on dialysis in Tris buffer under aerobic conditions , and on incubating with NADPH, but not NADH, in muscle and brain, but not yeast, enzymes. The results suggest that the inverse relationship of the dehydrogenase and ADP-ribosylation activities is coincidental but not correlated

New flame-retardant poly(pyromellitic imide aryl phosphoramide-ester)s

Flame-retardant poly(pyromellitic imide aryl phosphoramide-ester)s were synthesized by interfacial polycondensation of N,N?-bis(p-hydroxyphenyl)pyromellitic diimide with aryl phosphoramidic dichlorides. The polymers were characterized by IR and 1H-NMR spectroscopy. The molecular composition was confirmed by elemental analysis. The thermal stability and flammability of the polymers were studied by thermogravimetry and limiting oxygen index, respectively. Durch Grenzflächen-Polykondensation von N,N?-bis(4-hydroxyphenyl)pyromellitsäurediimid mit Dichloriden verschiedener Phosphoramide wurden flammhemmende Polymere erhalten. Diese wurden mittels IR- und 1H-NMR-Spektroskopie und Elementaranalyse charakterisiert. Thermische Stabilität und Entflammbarkeit wurden thermogravimetrisch bzw. durch Bestimmung des Sauerstoff-Indexes untersucht.

Novel photocrosslinkable liquid-crystalline polymers: poly[bis(benzylidene)] esters

A new class of photo-cross-linkable main-chain liquid crystalline polymers (PMCLCPs) containing bis(benzylidene)cycloallranone groups have been synthesized and studied for their liquid crystalline and photochemical properties. The bis(benzylidene)cycloalkanone group in the chain functions both as a mesogen and as a photoreactive center. All of the polymers exhibit a nematic mesophase. Two kinds of photoreactions, namely, photoisomerization and photo-cross-linking, operate in these polymers. Above Tu at the initial stages of irradiation, photoisomerization predominates the cross-linking, which resulta in the disruption of the chromophore aggregates. Below T8, because of the restricted mobility of the chains, only cross-linking takes place. Studies on the model compound, bis(benzylidene)cyclopentanone, confii the above observations and demonstrate further that the cross-linking proceeds by the 2r + 2r cycloaddition reaction of the bis(benzylidene)cycloallranone moieties. The cross-linking rate decreases with increase in the size of the cycloalkanone ring. Heating the solution cast polymer fii results in the ordered aggregation of the chromophores just above TI and also at the crystal to crystal transition temperature, which facilitates the phobcross-linking reactions. In the isotropic phase, the random orientation of the chromophores drastically curtails the cross-linking rata