Influencia de la refusion en las propiedades mecanicas y composicion quimica de aleaciones odontologicas

The objective of the study presented in this article was to analyze the influence of remelting of two odontological alloys: Dentorium and Steeldent, on the mechanical properties and on the chemical composition. For the two alloys, samples, containing 10% and 50% new alloy, were subjected to tensile test, micrography and chemical analysis. The alloys presented similar mechanical properties, except for the elongation, which presented higher values for the Dentorium 50% new alloy. This is due to the smaller carbides formed in this sample. The remelting itself seems not to be responsible for these differences, but they are probably due to the lack of a good control of the casting process. The micrography showed a dendritic column matrix, with carbides in the interdentric region and inside dendritic grain. In the chemical composition was observed few elements percentage change.

Estudio de la adición de K+ y LiNbO3 en las propiedades finales del relaxor PMN procesado por mezcla de polvos

PMN ceramic relaxor has been investigated by several researchers and many aspects of this material, like powder morphology, phase decomposition, weight loss during sintering process, densification, between others, still are investigated. PMN powder preparation has been shown more efficient when synthesized by columbite route, however lead addition stage for the PMN powder synthesis remains problematical. Therefore, this work proposes a new association of methodologies, using columbite route and the hydroxide precipitation method. Through use of the powder mixture technique, which permitted to obtain good green and sintered densities, was possible to observe K+ y Li + dopants reduce weight loss in sintering process and change significantly the dielectric properties. Addition of LiNbO3 seeds in conformation stage, which react in a distinct way as a function of the particle size, promotes the formation of differenced grains in the ceramic bulk. Consequently, very different dielectrics properties from conventional PMN ceramic were obtained.

Influencia del TiO2 y Al2O3 sobre las propiedades eléctricas y microestructurales de cerámicas de SnO2 obtenidas por el método Pechini

Tin oxide has wakened up great scientific and technological interest for its potential use in varistors production and as gas sensor. In order to improve the microstructural and electrical properties in SnO varistor ceramics, the influence of differents dopants used, like TiO2 and Al2O3, is under research. The effect of TiO2 and Al2O3 on the properties of Sn-Co-Nb varistor Systems obtained by the Pechini method has been investigated in this work. Characterization of synthesized raw material was performed by X-Ray Diffraction (XRD) and Scanning Electronic Microscopy (SEM). The microstructural and electrical characterization of sintered samples show that the TiO2 favors the grain growth and the Al2O3, contributes to the decrease it, effect that is manifested in the Sn-Co-Nb varistor systems. Breakdown field increase up to 6300V/cm with increasing Al2O3 content and non-linear coefficients with α=22 were obtained.

Efecto del método de secado en las propiedades termodinámicas de pulpa de mora en polvo

Three different types of maltodextrin encapsulated dehydrated blackberry fruit powders were obtained using vibrofluidized bed drying (VF), spray drying (SD), vacuum drying (VD), and freeze drying (FD). Moisture equilibrium data of blackberry pulp powders with 18% maltodextrin were determined at 20, 30, 40, and 50°C using the static gravimetric method for the water activity range of 0.06-0.90. Experimental equilibrium moisture content data versus water activity were fit to the Guggenheim-Anderson-de Boer (GAB) model. Agreement was found between experimental and calculated values. The isosteric heat of sorption of water was determined using the Clausius-Clapeyron equation from the equilibrium data; isosteric heats of sorption were found to increase with increasing temperature and could be adjusted by an exponential relationship. For freeze dried, vibrofluidized, and vacuum dried pulp powder samples, the isosteric heats of sorption were lower (more negative) than those calculated for spray dried samples. The enthalpy-entropy compensation theory was applied to sorption isotherms and plots of ΔH versus ΔS provided the isokinetic temperatures, indicating an enthalpy-controlled sorption process.

Fabricação e caracterização morfológica de filmes layer-by-layer de DODAB/FTALOCIANINA de níquel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Fases magnéticas em compostos Er'Co IND. x''Mn IND. 1-x''O IND> 3+ou - δ'

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Caracterização de filmes finos de YBa2Cu3O7-x e La0.7Ca0.3MnO3 produzidos via síntese química

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Propriedades magnéticas do modelo de Ising bidimensional em uma rede bipartida de spins 1/2 e 1: um estudo de ferrimagnetismo com vacâncias

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Síntesis de la oferta de América Latina y demanda de los mayores mercados mundiales, de los principales metales, 1970-1990: aluminio, cobre, hierro, níquel, plomo, zinc, estaño

Incluye Bibliografía

Propiedades de las maderas de Panamá

Incluye Bibliografía

Avaliação da instrumentação rotatória com limas de níquel e titânio, K3 e RaCe, em canais radiculares curvos simulados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da resistência à fratura torcional de diferentes instrumentos rotatórios de níquel-titânio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise radiográfica da modelagem de canais radiculares ovalados realizada com sistemas rotatórios de níquel-titânio

Pós-graduação em Odontologia - FOAR

Síntese e caracterização de nanopartículas magnéticas de óxido de ferro para aplicações biomédicas – um estudo citotóxico em linhagem celular de carcinoma cervical humano (células HeLa)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)