Estudo da infiltração marginal em restaurações de resinas compostas para dentes posteriores. Efeito do material, preparo cavitário e condicionamento do esmalte a nível cervical.

The purpose of this in vitro study was to investigate the cervical marginal leakage in class II restorations with chemically cured resin (P10) and light-cured resin (P30) in two types of cavities: conventional and adhesive. The effect of acid-etching in this area was also observed. Dentine adhesive Scotchbond was used in all experimental groups. Leakage was evidenced by Rodamina B dye penetration after thermocycling procedure between 10 degrees C and 50 degrees C temperature and analysed by using Zeiss Stereoscopic Magnifying Glass (10 X). According to the results obtained marginal leakage occurred in all experimental groups, with lower percentage for adhesives cavities when enamel acid-etching and light-cured resin P30 was used.

Method for marginal measurements of restorations: accessory device for toolmakers microscope.

Standardization of measurements for marginal fit of castings is critical. This study describes the fabrication of a device that allowed fixation of specimens on a Toolmakers microscope with identical conditions according to tri-dimensional positioning of specimens, measuring location, and seating force. The device also allows mapping of the marginal discrepancies on the entire marginal perimeter of the tooth preparation.

Marginal fit of nickel-chromium copings before and after internal adjustments with duplicated stone dies and disclosing agent.

STATEMENT OF PROBLEM: Despite careful procedures, master stone dies may be damaged during laboratory procedures. The dentist routinely adjusts castings because the marginal fit of casting is not as accurate as on the dies. PURPOSE: This study evaluated the technique of internal adjustment of castings with use of duplicated stone dies and a disclosing agent to improve marginal fit discrepancy. MATERIAL AND METHODS: Thirty-two nickel-chromium copings were fabricated and simulated standard clinical and laboratory procedures with 2 variables: tooth preparation convergence angles of 6 and 18 degrees, with or without internal relief. Master stone dies and their duplicates were selected for coping construction and internal adjustment, respectively. A specimen positioning device was coupled with a Toolmakers microscope to allow reproducibility of measurements. Each coping was evaluated at 8 locations of its marginal perimeter, before and after internal adjustment. RESULTS: Marginal fit discrepancy of copings were significantly reduced with an internal adjustment technique (mean > 52%) for all experimental groups. Tooth preparations with greater convergence and internally relieved castings recorded a better marginal fit. CONCLUSION: The casting internal adjustment technique with use of duplicated stone dies and a disclosing agent substantially reduced marginal fit discrepancy.

Caring for organ donors: The intensive care unit nurses' view

The nursing care for patients who are pronounced brain-dead but kept alive to serve as organ donors demands technical-scientific skills and the ability to handle situations that are often in conflict with the traditional concepts of nursing care. Based on the phenomenological approach in this article, essential themes of the lived experience of caring for these patients, including the technical and specific nursing care, the relationship with organ donors and their families, and the nurses' perception of themselves in this professional situation are described. The results point to the contradictions and ambiguities of this type of nursing, especially in regards to the affective and philosophical aspects.

Evaluation of marginal microleakage in Class II cavities: Effect of microhybrid, flowable, and compactable resins

Objective: The goal of the present study was to evaluate the microleakage on the cementum/dentin and enamel surfaces in Class II restorations, using different kinds of resin composite (microhybrid, flowable, and compactable). Method and materials: Forty human caries-free molars were extracted and selected. Eighty Class II standardized cavities were made in the cervical wall at the cementoenamel junction (CEJ) and at the mesial and distal surfaces. The teeth were divided into four groups: G1 - adhesive system + microhybrid resin composite Z100; G2 - adhesive system + compactable resin composite Prodigy Condensable; G3 - adhesive system + flowable resin composite Revolution + Z100 resin composite; G4 - adhesive system + Revolution fluid resin + compactable resin composite Prodigy Condensable. The adhesive system used in this study was Scotchbond Multi-Purpose Plus. The specimens were thermocycled in baths of 5°C and 55°C for 1,000 cycles and immersed in 50% silver nitrate solution. The specimens then were sectioned and evaluated on degree of dye penetration. Results: The results were evaluated using the nonparametric Kruskall-Wallis test, which showed a statistically significant difference between groups G1 and G4, G2 and G4, and G3 and G4. Conclusions: None of the materials was able to eliminate the marginal microleakage at the cervical wall; the application of a low-viscosity resin composite combined with a compactable resin composite significantly decreased the microleakage.

Progression of liver fibrosis in blood donors infected with hepatitis C virus

Background/Aims. Chronic hepatitis by HCV is progressive towards cirrhosis, with variable rate. We evaluated the rate of fibrosis progression (RFP), risk factors associated with advanced fibrosis (F3 and F4), and estimated the evolution time to cirrhosis. Methods. We transversely selected 142 blood donors infected only with HCV, with a known route of infection, submitted to liver biopsy at admission. RFP= ratio between stage of fibrosis (METAVIR)/estimated duration of infection in years. Non-parametric tests and logistic regression analysis, with significance level of 5% were used. Results. Median RFP was 0.086 U/year (0.05 - 0.142). Ten patients had F4 and 25 had F3. Median RFP values were significantly different (p=0.001) from one age group at contamination to the others and ALT and AST levels. There were no differences in the expected evolution to cirrhosis between intermediate fibrosers (F2) and the rapid fibrosers (F3 and F4). The independent variables associated with advanced fibrosis were ALT (OR 7.2) and GGT (OR 6.4) and age at inclusion (OR 1.12). Conclusion. This study suggests that RFP is extremely variable, it is exponential with age, and mainly influenced by host characteristics, especially age at contamination and possibly ethnical group. These asymptomatic patients had high percentage of fibrosis F2, F3 and F4.

A biodiversidade bentônica em lagoa marginal ao rio Paranapanema na zona de sua desembocadura, na represa de Jurumirim

Coqueiral lake is a marginal lake located at the southeast São Paulo State, in the mouth zone of the Paranapanema river into Jurumirim Reservoir and it has high connectivity with the Paranapaneina river. This work aimed to verify the benthic biodiversity in areas of the lake bottom. 18 sampling sites in the lake were selected, including shallow and deep areas. The samples were taken every three months during one year. Physical and chemical water variables (level, transparency, dissolved oxygen, pH, and electric conductivity) were analyzed. Sediment samples were picked up in triplicate for fauna and abiotic factors analysis (granulometric composition and sediment organic content), using Petersen dredge. The material was sorted out and analyzed under stereoscopic microscope. Counting and identification of the organisms were accomplished and diversity, relative abundance, taxonomic richness and dominance index were calculated. The analysis revealed a fauna with low species diversity and, with Chironomidae and Ephemeroptera dominance. Ephemeroptera, Campsurus, dominated in the hottest period and with low lake depth. Organisms' distribution had as main factors depth, transparency, pH, and water temperature. In the comparison between shallow and deep areas, a small density of organism in the deep regions was observed.

Influence of cavity preparation and curing method on the marginal seal of resin composite restorations: an in vitro evaluation.

OBJECTIVE: To evaluate the influence of cavity design and photocuring method on the marginal seal of resin composite restorations. METHOD AND MATERIALS: Seventy-two bovine teeth were divided into 2 groups: group 1 received box-type cavity preparations, and group 2 received plate-type preparations. Each group was divided into 3 subgroups. After etching and bonding, Z250 resin composite (3M Espe) was applied in 2 equal increments and cured with 1 of 3 techniques: (1) conventional curing for 30 seconds at 650 mW/cm2; (2) 2-step photocuring, in which the first step was performed 14 mm from the restoration for 10 seconds at 180 mW/cm2 and the second step was performed in direct contact for 20 seconds at 650 mW/cm2; or (3) progressive curing using Jetlite 4000 (J. Morita) for 8 seconds at 125 mW/cm2 and then 22 seconds at 125 mW/cm2 up to 500 mW/cm2. The specimens were thermocycled for 500 cycles and then submitted to dye penetration with a 50% silver nitrate solution. Microleakage was assessed using a stereomicroscope. Data were analyzed using analysis of variance and Tukey test (5% level of significance). RESULTS: A statistically significant difference was found between groups when a double interaction between photocuring and cavity preparation was considered (P = .029). CONCLUSIONS: No one type of cavity preparation or photocuring method prevented micro-leakage. The plate-type preparation showed the worst dye penetration when conventional and progressive photocuring methods were used. The best results were found using the 2-step photocuring with the plate-type preparation.

Effect of cast rectifiers on the marginal fit of UCLA abutments

Objectives: This study assessed the effect of cast rectifiers on the marginal misfit of cast UCLA abutments compared to premachined UCLA abutments. The influence of casting and porcelain baking on the marginal misfit of these components was also investigated. Methods: Two groups were analyzed: test group - 10 cast UCLA abutments, finished with cast rectifier and submitted to ceramic application; control group - 10 premachined UCLA abutments, cast with noble metal alloy and submitted to ceramic application. Vertical misfit measurements were performed under light microscopy. In the test group, measurements were performed before and after the use of cast rectifiers, and after ceramic application. In the control group, measurements were performed before and after casting, and after ceramic application. Data were submitted to statistical analysis by ANOVA and Tukey's test (α= 5%). Results: The use of cast rectifiers significantly reduced the marginal misfit of cast UCLA abutments (from 25.68μm to 14.83μm; p<0.05). After ceramic application, the rectified cylinders presented misfit values (16.18μm) similar to those of premachined components (14.3 μm). Casting of the premachined UCLA abutments altered the marginal misfit of these components (from 9.63 μm to 14.6 μm; p<0.05). There were no significant changes after porcelain baking, in both groups. Conclusion: The use of cast rectifiers reduced the vertical misfit of cast UCLA abutments. Even with carefully performed laboratory steps, changes at the implant interface of premachined UCLA abutments occurred. Ceramic application did not alter the marginal misfit values of UCLA abutments.

In vitro evaluation of marginal leakage in bonded restorations, with mechanical or chemical-mechanical (Carisolv) removal of carious tissue

This study carried out an in vitro evaluation and comparison of the occurrence of marginal leakage in bonded restorations using mechanical or chemical-mechanical (Carisolv) removal of carious tissue. For that purpose, 40 extracted decayed human molars were divided into 4 groups: GI (burs + Prime & Bond NT + TPH), GII (Carisolv + Prime & Bond NT + TPH), GIII (burs + SBMP + Z100) and GIV (Carisolv + SBMP + Z100). After accomplishment of the restorations and thermal cycling, the teeth were exposed to dye, sectioned and qualitatively evaluated. The results demonstrated that the system of removal of carious tissue did not influence the results of microleakage at any of the cavity margins. At dentinal margins, use of the Prime & Bond NT + TPH restorative system allowed the occurrence of less microleakage than the SBMP + Z100 system.

The effect of endodontic materials on the optical density of dyes used in marginal leakage studies

The aim of this study was to determine the effect of the exposure of different endodontic materials to different dye solutions by evaluating the optical density of the dye solutions. Seventy-five plastic tubes were filled with one of the following materials: AH Plus, Sealapex, Portland cement, MTA (Angelus and Pro Root) and fifteen control plastic tubes were not. Each specimen of material and control was immersed in a container with 1 ml of each dye solution. A 0.1 ml-dye solution aliquote was removed before immersion and after 12, 24, 48 and 72 hours of each specimen immersion to record its optical density (OD) in a spectrophotometer. Statistical analysis was performed with ANOVA and Tukey tests (5%). No significant difference was found among any of the solution OD values for AH Plus cement. Portland cement promoted different OD values after 12 hours of immersion. MTA-Angelus cement presented different OD values only for 2% rhodamine B and the MTA-Pro Root cement presented different OD values in all 2% rhodamine B samples. Sealapex cement promoted a reduction in the India Ink OD values. Dye evaluation through OD seems to be an interesting method to select the best dye solution to use in a given marginal leakage study.

Frequency of the HFE C282Y and H63D polymorphisms in Brazilian malaria patients and blood donors from the Amazon region

Malaria is an endemic parasitosis and its causitive agent, Plasmodium, has a metabolism linked to iron supply. HFE is a gene with the polymorphisms C282Y and H63D, which are associated with a progressive iron accumulation in the organism leading to a disease called hereditary hemochromatosis. The aim of the present study was to determine the allelic and genotypic frequencies of the HFE gene polymorphisms in malaria patients and blood donors from the Brazilian Amazon region. We screened 400 blood donors and 400 malaria patients for the HFE C282Y and H63D polymorphisms from four states of the Brazilian Amazon region by polymerase chain reaction and restriction fragment length polymorphism analysis. We did not find any C282Y homozygous individuals, and the only five heterozygous individuals detected were from Pará State. The most frequent genotype in the North region of Brazil was the H63D heterozygote, in both study groups. Our results contribute to the concept that the Brazilian Amazon region should not be regarded as a single entity in South America. These polymorphisms did not influence the symptoms of malaria in the population studied, as neither severe signs nor high parasitemia were observed. Therefore, different hereditary hemochromatosis diagnostic and control measures must be developed and applied within its diverse locations. Investigations are currently being carried out in our laboratory in order to determine the importance of the coexistence of hereditary hemochromatosis in patients affected by parasitic diseases, such as malaria. ©FUNPEC-RP.

Estudios sobre la juventud marginal latinoamericana

Incluye Bibliografía

Financing for development and middle income-countries: new challenges

Spanish version avalilable at the Library

Frequency of ABO blood group system polymorphisms in Plasmodium falciparum malaria patients and blood donors from the Brazilian Amazon region.

We investigated the ABO genotypes and heterogeneity of the O alleles in Plasmodium falciparum-infected and non-infected individuals from the Brazilian Amazon region. Sample collection took place from May 2003 to August 2005, from P. falciparum malaria patients from four endemic regions of the Brazilian Amazon. The control group consisted of donors from four blood banks in the same areas. DNA was extracted using the Easy-DNA(TM) extraction kit. ABO genotyping was performed using PCR/RFLP. There was a high frequency of ABO*O01O01. ABO*AO01 was the second most frequent genotype, and the third most frequent genotype was ABO*BO01. There were low frequencies of the ABO*O01O02, ABO*AA, ABO*AB, ABO*BB, and ABO*O02O02 genotypes. We analyzed the alleles of the O phenotype; the O(1variant) allele was the most frequent, both in malaria and non-malaria groups; consequently, the homozygous genotype O(1)(v)O(1)(v) was the most frequently observed. There was no evidence of the homozygous O(2) allele. Significant differences were not detected in the frequency of individuals with the various alleles in the comparison of the malaria patients and the general population (blood donors).