Biaxial failure model for fiber reinforced concrete

Steel fiber reinforced concrete (SFRC) is widely applied in the construction industry. Numerical elastoplastic analysis of the macroscopic behavior is complex. This typically involves a piecewise linear failure curve including corner singularities. This paper presents a single smooth biaxial failure curve for SFRC based on a semianalytical approximation. Convexity of the proposed model is guaranteed so that numerical problems are avoided. The model has sufficient flexibility to closely match experimental results. The failure curve is also suitable for modeling plain concrete under biaxial loading. Since this model is capable of simulating the failure states in all stress regimes with a single envelope, the elastoplastic formulation is very concise and simple. The finite element implementation is developed to demonstrate the conciseness and the effectiveness of the model. The computed results display good agreement with published experimental data.

In situ characterization of stickiness of sugar-rich foods using a linear actuator driven stickiness testing device

A stickiness testing device based on the probe tack test has been designed and tested. It was used to perform in situ characterization of drying hemispherical drops with an initial radius 3.5 mm. Tests were carried out in two drying temperatures, 63 and 95 degreesC. Moisture and temperature histories of the drying drops of fructose, honey, sucrose, maltodextrin and sucrose-maltodextrin mixtures were determined. The rates of moisture evaporation of the fructose solution was the fastest while those of the maltodextrin solution was the lowest. A profile reversal was observed when the temperature profiles of these materials were compared. Different modes of failure were observed during the stickiness tests. Pure fructose and honey solutions remained completely sticky and failed cohesively until the end of drying. Pure sucrose solution remained sticky and failed cohesively until complete crystallization occurred. The surface of the maltodextrin drops formed a skin shortly after the start of drying. It exhibited adhesive failure and reached a state of non-adhesion. Addition of maltodextrin significantly altered the stickiness of sucrose solution. (C) 2002 Elsevier Science Ltd. All rights reserved.

A reduced load approximation accounting for link interactions in a loss network

This paper is concerned with evaluating the performance of loss networks. Accurate determination of loss network performance can assist in the design and dimen- sioning of telecommunications networks. However, exact determination can be difficult and generally cannot be done in reasonable time. For these reasons there is much interest in developing fast and accurate approximations. We develop a reduced load approximation that improves on the famous Erlang fixed point approximation (EFPA) in a variety of circumstances. We illustrate our results with reference to a range of networks for which the EFPA may be expected to perform badly.

A class B switch-mode assisted linear amplifier

A switch-mode assisted linear amplifier (SMALA) combining a linear (Class B) and a switch-mode (Class D) amplifier is presented. The usual single hysteretic controlled half-bridge current dumping stage is replaced by two parallel buck converter stages, in a parallel voltage controlled topology. These operate independently: one buck converter sources current to assist the upper Class B output device, and a complementary converter sinks current to assist the lower device. This topology lends itself to a novel control approach of a dead-band at low power levels where neither class D amplifier assists, allowing the class B amplifier to supply the load without interference, ensuring high fidelity. A 20 W implementation demonstrates 85% efficiency, with distortion below 0.08% measured across the full audio bandwidth at 15 W. The class D amplifier begins assisting at 2 W, and below this value, the distortion was below 0.03%. Complete circuitry is given, showing the simplicity of the additional class D amplifier and its corresponding control circuitry.

Pseudo-randomness of round-off errors in discretized linear maps on the plane

We analyze the sequences of round-off errors of the orbits of a discretized planar rotation, from a probabilistic angle. It was shown [Bosio & Vivaldi, 2000] that for a dense set of parameters, the discretized map can be embedded into an expanding p-adic dynamical system, which serves as a source of deterministic randomness. For each parameter value, these systems can generate infinitely many distinct pseudo-random sequences over a finite alphabet, whose average period is conjectured to grow exponentially with the bit-length of the initial condition (the seed). We study some properties of these symbolic sequences, deriving a central limit theorem for the deviations between round-off and exact orbits, and obtain bounds concerning repetitions of words. We also explore some asymptotic problems computationally, verifying, among other things, that the occurrence of words of a given length is consistent with that of an abstract Bernoulli sequence.

Comparação de desempenho entre a formulação direta do Método dos Elementos de Contorno com Funções Radiais e o Método dos Elementos Finitos em problemas de Poisson e Helmholtz

O presente trabalho objetiva avaliar o desempenho do MECID (Método dos Elementos de Contorno com Interpolação Direta) para resolver o termo integral referente à inércia na Equação de Helmholtz e, deste modo, permitir a modelagem do Problema de Autovalor assim como calcular as frequências naturais, comparando-o com os resultados obtidos pelo MEF (Método dos Elementos Finitos), gerado pela Formulação Clássica de Galerkin. Em primeira instância, serão abordados alguns problemas governados pela equação de Poisson, possibilitando iniciar a comparação de desempenho entre os métodos numéricos aqui abordados. Os problemas resolvidos se aplicam em diferentes e importantes áreas da engenharia, como na transmissão de calor, no eletromagnetismo e em problemas elásticos particulares. Em termos numéricos, sabe-se das dificuldades existentes na aproximação precisa de distribuições mais complexas de cargas, fontes ou sorvedouros no interior do domínio para qualquer técnica de contorno. No entanto, este trabalho mostra que, apesar de tais dificuldades, o desempenho do Método dos Elementos de Contorno é superior, tanto no cálculo da variável básica, quanto na sua derivada. Para tanto, são resolvidos problemas bidimensionais referentes a membranas elásticas, esforços em barras devido ao peso próprio e problemas de determinação de frequências naturais em problemas acústicos em domínios fechados, dentre outros apresentados, utilizando malhas com diferentes graus de refinamento, além de elementos lineares com funções de bases radiais para o MECID e funções base de interpolação polinomial de grau (um) para o MEF. São geradas curvas de desempenho através do cálculo do erro médio percentual para cada malha, demonstrando a convergência e a precisão de cada método. Os resultados também são comparados com as soluções analíticas, quando disponíveis, para cada exemplo resolvido neste trabalho.

Testes para verificar a igualdade de parâmetros e a identidade de modelos de regressão não-linear em dados de experimento com delineamento em blocos casualizados

Considerou-se o ajustamento de equações de regressão não-linear e o teste da razão de verossimilhança, com aproximações pelas estatísticas qui-quadrado e F, para testar as hipóteses de igualdade de qualquer subconjunto de parâmetros e de identidade dos modelos para dados com repetições provenientes de experimento com delineamento em blocos completos casualizados. Concluiu-se que as duas aproximações podem ser utilizadas, mas a aproximação pela estatística F deve ser preferida, principalmente para pequenas amostras.

Atributos físicos de um Latossolo Vermelho correlacionados linear e espacialmente com a consorciação de guandu com milheto

O sistema cultivo mínimo, por possibilitar pouca movimentação de solo, menor número de operações agrícolas sem incorporação dos resíduos vegetais, apresenta vantagens em razão do menor custo de preparo e da redução das perdas de solo e água. No ano agrícola de 2006/2007, na Fazenda de Ensino e Pesquisa da Faculdade de Engenharia de Ilha Solteira, SP, Brasil - FEIS/UNESP, situada nas condições do Cerrado Brasileiro, objetivou-se analisar a produtividade de massa de matéria seca da consorciação de forragem (guandu+milheto) (MSF), em função de atributos físicos do solo, tais como resistência à penetração (RP), umidade gravimétrica (UG), umidade volumétrica (UV) e densidade do solo (DS) nas profundidades de 0,0-0,10 m; 0,10-0,20 m e 0,20-0,30 m. Para tanto, foi instalado um ensaio, contendo 117 pontos amostrais, em um Latossolo Vermelho distroférrico, sob pivô central, numa área experimental de 1600 m² sob cultivo mínimo. A análise estatística constou de análise descritiva inicial dos atributos e análise das correlações lineares simples entre eles, e, finalmente, de análise geoestatística. Do ponto de vista da correlação espacial, o atributo que mais bem explica a produtividade de massa de matéria seca da consorciação é a densidade do solo na camada de 0,20-0,30 m, com uma correlação inversa, indicando que as espécies se desenvolvem bem em solos adensados.

Portugal’s Minho-Lima region as a tourist destination: tourism operators’ attitudes towards its management and promotion

The success of tourism development depends on the capacity of a region’s tourism agents to establish and sustain networks, involving both private-sector companies and the public sector. Creating an attractive destination able to compete with others that are better positioned and consolidated requires cooperative behaviour among the various agents involved. This behaviour will facilitate both external and internal competition, which in turn will assure better product quality, continuous product renewal, a strong offer of unique experiences and the efficient use of endogenous resources. In this paper, the authors discuss the results of a survey of restaurant owners and of interviews conducted with the main institutional agents concerned with tourism promotion and the economic development of the Minho–Lima region. Such an approach, the authors argue, can be valuable in identifying the strengths and weaknesses of the area in question with regard to future tourism development. The authors work from the premise that the commitment of tourism agents constitutes a precondition for the success of the strategy to be defined. This is especially applicable to Minho–Lima, which to date has suffered from an absence of commitment and coordination on the part of those agents.

Eigenvalue computations in the context of data-sparse approximations of integral operators

In this work, we consider the numerical solution of a large eigenvalue problem resulting from a finite rank discretization of an integral operator. We are interested in computing a few eigenpairs, with an iterative method, so a matrix representation that allows for fast matrix-vector products is required. Hierarchical matrices are appropriate for this setting, and also provide cheap LU decompositions required in the spectral transformation technique. We illustrate the use of freely available software tools to address the problem, in particular SLEPc for the eigensolvers and HLib for the construction of H-matrices. The numerical tests are performed using an astrophysics application. Results show the benefits of the data-sparse representation compared to standard storage schemes, in terms of computational cost as well as memory requirements.

Error bounds for low-rank approximations of the first exponential integral kernel

A hierarchical matrix is an efficient data-sparse representation of a matrix, especially useful for large dimensional problems. It consists of low-rank subblocks leading to low memory requirements as well as inexpensive computational costs. In this work, we discuss the use of the hierarchical matrix technique in the numerical solution of a large scale eigenvalue problem arising from a finite rank discretization of an integral operator. The operator is of convolution type, it is defined through the first exponential-integral function and, hence, it is weakly singular. We develop analytical expressions for the approximate degenerate kernels and deduce error upper bounds for these approximations. Some computational results illustrating the efficiency and robustness of the approach are presented.

Application of Gage R&R methodology for improving the training and evaluation of automatic optical inspection machine operators

The current level of demand by customers in the electronics industry requires the production of parts with an extremely high level of reliability and quality to ensure complete confidence on the end customer. Automatic Optical Inspection (AOI) machines have an important role in the monitoring and detection of errors during the manufacturing process for printed circuit boards. These machines present images of products with probable assembly mistakes to an operator and him decide whether the product has a real defect or if in turn this was an automated false detection. Operator training is an important aspect for obtaining a lower rate of evaluation failure by the operator and consequently a lower rate of actual defects that slip through to the following processes. The Gage R&R methodology for attributes is part of a Six Sigma strategy to examine the repeatability and reproducibility of an evaluation system, thus giving important feedback on the suitability of each operator in classifying defects. This methodology was already applied in several industry sectors and services at different processes, with excellent results in the evaluation of subjective parameters. An application for training operators of AOI machines was developed, in order to be able to check their fitness and improve future evaluation performance. This application will provide a better understanding of the specific training needs for each operator, and also to accompany the evolution of the training program for new components which in turn present additional new difficulties for the operator evaluation. The use of this application will contribute to reduce the number of defects misclassified by the operators that are passed on to the following steps in the productive process. This defect reduction will also contribute to the continuous improvement of the operator evaluation performance, which is seen as a quality management goal.

Regressão linear com duplo truncamento na distribuição da variável dependente

Do problema do ajuste de uma regressão linear, quando a distribuição da variável dependente tem duplo truncamento, utilizando a função de máxima verossimilhança e um processo iterativo.

Análise multivariada: um exemplo usando modelo log-linear

Apresenta-se de forma resumida análise multivariada de dados categóricos, usando modelo log-linear para a situação de uma tabela de contingência 2 x 2 x 2.