Estudo do sistema celulose bacteriana-poliuretano para a produção de novos compósitos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de equipamento para avaliação em campo da dureza de madeiras para dormente ferroviário

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Torneamento de liga de níquel Pyromet 31V (N07032) com ferramentas de metal duro

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização mecânica e microestrutural de um aço 4340 com estrutura multifásicas e tratamento de nitrocarbonetação a plasma

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desempenho reprodutivo de cordeiras suplementadas em comedouro privativo

Pós-graduação em Zootecnia - FMVZ

Identificação de genótipos superiores para crescimento e qualidade de carcaça em bovinos de corte submetidos ao modelo biológico superprecose

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Níveis plasmáticos hormonais e crescimento muscular de bovinos superprecoces recebendo somatotropina bovina recombinante (rbST)

Pós-graduação em Zootecnia - FMVZ

Obtenção da liga Ti-35Nb por metalurgia do pó para utilização em próteses ortopédicas

Pós-graduação em Engenharia Mecânica - FEG

Efeito de diferentes taxas de resfriamento sobre a porcelana feldspática de cobertura para infraestrutura em zircônia

Pós-graduação em Reabilitação Oral - FOAR

Caracterização mecânica de uma porcelana de aplicação convencional e uma prensada para recobrimento de infraestruturas de zircônia e o efeito do método de resfriamento na resistência à flexão biaxial do conjunto zircônia/porcelana

Pós-graduação em Reabilitação Oral - FOAR

Structural and optical properties of brominated plasma polymers

Novel brominated amorphous hydrogenated carbon (a-C:H:Br) films were produced by the plasma polymerization of acetylene-bromoform mixtures. The main parameter of interest was the degree of bromination, which depends on the partial pressure of bromoform in the plasma feed, expressed as a percentage of the total pressure, R-B. When bromoform is present in the feed, deposition rates of up to about 110 nm min(-1) may be obtained. The structure and composition of the films were characterized by Transmission Infrared Reflection Absorption Spectroscopy (IRRAS) and X-ray Photo-electron Spectroscopy (XPS). The latter revealed that films with atomic ratios Br:C of up to 0.58 may be produced. Surface contact angles, measured using goniometry, could be increased from similar to 63 degrees (for an unbrominated film) to similar to 90 degrees for R-B of 60 to 80%. Film surface roughness, measured using a profilometer, does not depend strongly on R-B. Optical properties the refractive index, n, absorption coefficient, alpha(E), where E is the photon energy, and the optical gap, E-g, were determined from film thicknesses and data obtained by Transmission Ultraviolet-Visible Near Infrared Spectroscopy (UVS). Control of n was possible via selection of R-B. The measured optical gap increases with increasing F-BC, the atomic ratio of Br to C in the film, and semi-empirical modeling accounts for this tendency. A typical hardness of the brominated films, determined via nano-indentation, was similar to 0.5 GPa. (C), 2013 Elsevier B.V. All rights reserved.

Ethyl Ferulate, a Component with Anti-Inflammatory Properties for Emulsion-Based Creams

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da fragilização ao revenido em aço liga de 2,25CR-1MO através do ensaio de indentificação instrumentada

2,25Cr-1Mo alloy steels are widely used in petrochemical plant equipments working in high temperature conditions because of their good mechanical proprieties in these conditions. Although, when exposed for a long time at high temperature, in the rage of 343 °C to 593 °C, may present the temper embrittlement phenomenon. The component named stripper of assembly converter of fluid catalytic cracking unit (UFCC) of studied plant is manufactured using this material, which is subject to temper embrittlement. The phenomenon of temper embrittlement refers to progressive lose of toughness, making the material brittle. With embrittlement, equipaments manufactured with this material are under risks to suffer brittle fracture in the cool down and start-up situations of them, which can cause catastrophic failures. By this reason, this research studies presence of temper ebrittlement phenomenon on this material. To verify the toughness of the material is conventionally used charpy V-notch test. However, this test requires the removing of samples of the material to make specimens. This fact becomes critical when talk about structural components of an equipment. So, this research also studies a non-destructive test that can be executes in-situ, known as instrumented indentation, as an alternative detection of the phenomenon at the component stripper, by comparative of the mechanical proprieties obtained by conventional tests in similar samples

Estudo da fluência dos aços inoxidáveis ferríticos estabilizados ao titânio e nióbio e simulação numérica do processo no abaqus

The purpose of this research was tested a finite element model (FEM) that represented the creep of a slab during the reheating process of hot rolling. The aim is to prevent creep phenomenon changing the reheating profile with hot tensile test in Gleeble 3500, and, also, understand the former defect crisis. The goal of this work is to have a predictive tool to optimize the reheating process changing parameters (length and thickness). Then, use input parameters obtained from the tests to approximate the solution of the problem aided by Abaqus CAE. The results have showed that the ferritic stainless steel AISI 409 has a lower sensitivity to creep comparing to the stainless steel AISI 409, AISI 430Ti, AISI 441 and AISI 444

Avaliação dos danos por fluência da serpentina da caldeira da REVAP

The determination of the remaining life of equipment operating at high temperatures has been a great challenge for their owners. The use of safety factors, often conservative, makes the replacement of equipment or of its components at the end of the life of design gets financially unviable. This study aimed to estimate the remaining life of the serpentine of the secondary superheater of one of REVAP’s boilers (Henrique Lage Refinery), through accelerated creep tests and comparison of the results with the techniques based on microstructure and hardness. When conducting a proper assessment it’s possible to increase the equipment reliability, ensuring operational continuity and physical integrity. The tests showed a minimal residual life of 12.7 years (111,252 hours), longer than the design life (100,000 hours), even after a period of operation of approximately 250,000 hours, confirming the conservatism of the project. The techniques based on microstructure and hardness did not show good correlation with the creep test, decreasing the reliability of these techniques in determining the residual life