Pre-diseño de una instalación mixta fotovoltaica-térmica para una vivienda

El objetivo del presente proyecto es realizar el pre-diseño de una instalación solar mixta fotovoltaica-térmica para satisfacer la demanda eléctrica para iluminación y para parte de las necesidades de energía térmica para agua caliente de una vivienda. El proyecto define las condiciones técnicas de la instalación a partir de la radiación solar registrada en la localización elegida. Además de incluir el estudio económico y los planos correspondientes que indican la viabilidad del mismo. Como puntos a destacar en el proyecto, se puede tomar los datos obtenidos de generación eléctrica y térmica, la viabilidad técnica y económica y el análisis de la incipiente tecnología de paneles híbridos fotovoltaicos-térmicos. La incorporación de las energías renovables es ya una realidad para las viviendas de nueva construcción, en cambio son pocas las nuevas instalaciones en edificios o viviendas ya construidas. Es importante promover este tipo de tecnologías con objetivo de reducir la dependencia actual de los combustibles fósiles y evitar así sus efectos nocivos al medio ambiente. ABSTRACT The purpose of this project is to carry out the draft design of a solar mixed photovoltaic-thermal installation to satisfy the electrical and thermal demand in a building, for lighting as well as for some of the energy required for water heating. The project defines the technical conditions of the system, given the solar radiation registered in the chosen location. It also includes the economic analysis and the respective plans that indicates the viability of the project. The highlights of the project are the following: electricity and thermal energy generation data, the technical and financial viability and the analysis of the new technology of the Photovoltaic-Thermal hybrid solar collectors. The inclusion of renewable energies is already a living reality for newly constructed buildings. By contrast, they are rarely implemented in old buildings. In order to be able to reduce the fossil fuels dependency, and in doing so, avoid its damaging effects on the environment, it is very important to promote the use of these cleaner technologies.

Extracellular Matrix Assembly in Diatoms (Bacillariophyceae)1 : III. Organization of Fucoglucuronogalactans within the Adhesive Stalks of Achnanthes longipes

Achnanthes longipes is a marine, biofouling diatom that adheres to surfaces via adhesive polymers extruded during motility or organized into structures called stalks that contain three distinct regions: the pad, shaft, and collar. Four monoclonal antibodies (AL.C1–AL.C4) and antibodies from two uncloned hybridomas (AL.E1 and AL.E2) were raised against the extracellular adhesives of A. longipes. Antibodies were screened against a hot-water-insoluble/hot-bicarbonate-soluble-fraction. The hot-water-insoluble/hot-bicarbonate-soluble fraction was fractionated to yield polymers in three size ranges: F1, ≥ 20,000,000 Mr; F2, ≅100,000 Mr; and F3, <10,000 Mr relative to dextran standards. The ≅100,000-Mr fraction consisted of highly sulfated (approximately 11%) fucoglucuronogalactans (FGGs) and low-sulfate (approximately 2%) FGGs, whereas F1 was composed of O-linked FGG (F2)-polypeptide (F3) complexes. AL.C1, AL.C2, AL.C4, AL.E1, and AL.E2 recognized carbohydrate complementary regions on FGGs, with antigenicity dependent on fucosyl-containing side chains. AL.C3 was unique in that it had a lower affinity for FGGs and did not label any portion of the shaft. Enzyme-linked immunosorbent assay and immunocytochemistry indicated that low-sulfate FGGs are expelled from pores surrounding the raphe terminus, creating the cylindrical outer layers of the shaft, and that highly sulfated FGGs are extruded from the raphe, forming the central core. Antibody-labeling patterns and other evidence indicated that the shaft central-core region is related to material exuded from the raphe during cell motility.

Evolução das doses no ambiente do Reator IEA-R1 e tendências com base nos resultados atuais

O Ipen/Cnen-SP possui um Reator de Pesquisa(IEA-R1) em operação desde 1957. Ele utiliza água leve como blindagem, moderador e como fluido refrigerante, o volume desta piscina é de 273m3. Até 1995 a operação do Reator era descontinua, ou seja, operava diariamente sendo desligado no final do dia, a uma potência de 2,0 MW. A partir daquele ano, após algumas modificações de segurança, o Reator passou a operar de forma continua, ou seja, de segunda-feira a quarta-feira sem ser desligado, totalizando 64 horas semanais. A potência também foi aumentando até 4,5 MW em 2012. Em virtude dessas alterações, a saber, operação contínua e do aumento da potência, as doses dos trabalhadores aumentaram e por isso foram realizados vários estudos para diminui-las. Estudos demonstraram que uma das principais limitações para operação de um reator em potência elevada, provém das radiações gama emitidas pelo sódio-24. Outros elementos como magnésio-27, Alumínio-28, Argônio-51, contribuem de forma considerável para a atividade da água da piscina. A introdução de uma camada de água quente em sua superfície, estável e isenta de elementos radioativos com 1,5m a 2m de espessura constituiria uma blindagem às radiações provenientes dos elementos radioativos dissolvidos na água. Estudos de otimização provaram que a instalação da camada quente não era necessária para o regime e potência atual de operação do Reator, pois outros procedimentos adotados eram mais eficazes. A partir desta decisão o serviço de Proteção Radiológica do Reator IEA-R1, montou um programa de avaliação das doses para certificar-se de que elas se mantinham em valores razoáveis baseados em princípios estabelecidos em normas nacionais e internacionais. O intuito deste trabalho é realizar uma análise das doses individuais dos IOE (Individuo Ocupacionalmente Expostos), considerando as mudanças no regime de operação do Reator e sugerir opções de proteção e segurança, viáveis em primeira instância, para reduzir as doses analisadas, visando se chegar aos níveis de referencia de 3 mSv/ano adotados pela instalação em apreço.

Sustainable Energy Plan for a Small Island Economy: St. Vincent & the Grenadines

This paper defines a sustainable energy plan to provide the basis for renewable energy initiatives that will increase energy security, reduce negative economic impacts and provide a cleaner environment. The hotel, agriculture, transportation, construction, utility, government and private sectors will play pivotal roles in achieving targets and will see significant gains. Government policies, educational campaigns and financial incentives will be required to facilitate and encourage renewable energy development and entrepreneurship. Utilization of solar energy, energy conservation measures and the use of efficient and alternative fuel vehicles by the commercial/industrial and private sectors will be crucial in meeting targets. The utility company will be charged with developing large scale renewable energy applications and with improving efficiency of the electrical system.

THE TRANSPORT OF HEAT BY FLOWING GROUNDWATER IN A DISCRETE FRACTURE

In typical theoretical or experimental studies of heat migration in discrete fractures, conduction and thermal dispersion are commonly neglected from the fracture heat transport equation, assuming heat conduction into the matrix is predominant. In this study analytical and numerical models are used to investigate the significance of conduction and thermal dispersion in the plane of the fracture for a point and line sources geometries. The analytical models account for advective, conductive and dispersive heat transport in both the longitudinal and transverse directions in the fracture. The heat transport in the fracture is coupled with a matrix equation in which heat is conducted in the direction perpendicular to the fracture. In the numerical model, the governing heat transport processes are the same as the analytical models; however, the matrix conduction is considered in both longitudinal and transverse directions. Firstly, we demonstrate that longitudinal conduction and dispersion are critical processes that affect heat transport in fractured rock environments, especially for small apertures (eg. 100 μm or less), high flow rate conditions (eg. velocity greater than 50 m/day) and early time (eg. less than 10 days). Secondly, transverse thermal dispersion in the fracture plane is also observed to be an important transport process leading to retardation of the migrating heat front particularly at late time (eg. after 40 days of hot water injection). Solutions which neglect dispersion in the transverse direction underestimate the locations of heat fronts at late time. Finally, this study also suggests that the geometry of the heat sources has significant effects on the heat transport in the system. For example, the effects of dispersion in the fracture are observed to decrease when the width of the heat source expands.

High altitude cook book /

Sample recipes: English roast turkey, Hot water sponge cake, Mustard pickles.

The cell wall galactans from Australian representatives of the genus Meristotheca (solieriaceae, rhodophyta)

The Solieriaceae, has the largest number of genera (16-18) of any family in the carrageenophyte order Gigartinales. One of these genera, Meristotheca, consists of three or four species of foliose, erect to prostrate plants sporadically recorded from the tropics of both hemispheres. The hot-water-soluble polysaccharides from Australian representatives of the type species, M. papulosa, and M. procumbens from Lord Howe Island have been characterized by compositional assays, linkage analysis, and Fourier transform infrared and C-13-nuclear magnetic resonance spectroscopy. The results show that polysaccharides from both species are similar, being predominantly composed of 4-linked 3,6-anhydro-alpha-D-galactopyranose 2-sulphate alternating with 3-linked beta-D-galactopyranose 4-sulphate, as is typical of iota-carrageenan. Small proportions of the 3-linked units occur as the pyruvated residue 4,6-O-(1-carboxyethylidene)-beta-D-galactopyranose, and other minor variations from idealized iota-carrageenan were also detected. The polysaccharides from representatives of Meristotheca are comparable to those of other solieriacean algae analysed to date, but the minor structural variations suggest a closer chemotaxonomic affinity with noneucheumoid genera of the Solieriaceae, such as Sarconema, Solieria, and Tikvahiella, than to the eucheumoid genera Eucheuma, Kappaphycus and Betaphycus (tribe Eucheumatoideae) from which most kappa- and iota-carrageenans are commercially extracted.

Elicitors of induced disease resistance in postharvest horticultural crops: a brief review

Increasing loss of conventional fungicides due to pathogen resistance and general unacceptability in terms of public and environmental risk have favoured the introduction of integrated pest management (IPM) programmes. Induction of natural disease resistance (NDR) in harvested horticultural crops using physical, biological and/or chemical elicitors has received increasing attention over recent years, it being considered a preferred strategy for disease management. This article reviews the enhancement of constitutive and inducible antifungal compounds and suppression of postharvest diseases through using elicitors. The effect of timing of pre- and/or postharvest elicitor treatment and environment on the degree of elicitation and the potential for inducing local acquired resistance, systemic acquired resistance and/or induced systemic resistance to reduce postharvest disease is discussed. The review highlights that more applied and basic research is required to understand the role that induced NDR can play in achieving practical suppression of postharvest diseases as part of an IPM approach. (C) 2003 Elsevier B.V. All rights reserved.

Double-heater-wire circuits and heat-and-moisture exchangers and the risk of ventilator-associated pneumonia

Objective: To compare the incidence of ventilator-associated pneumonia (VAP) in patients ventilated in intensive care by means of circuits humidified with a hygroscopic heat-and-moisture exchanger with a bacterial viral filter (HME) or hot-water humidification with a heater wire in both inspiratory and expiratory circuit limbs (DHW) or the inspiratory limb only (SHW). Design: A prospective, randomized trial. Setting: A metropolitan teaching hospital's general intensive care unit. Patients: Three hundred eighty-one patients requiring a minimum period of mechanical ventilation of 48 hrs. Interventions: Patients were randomized to humidification with use of an HME (n = 190), SHW (n = 94), or DHW (n = 97). Measurements and Main Results. Study end points were VAP diagnosed on the basis of Clinical Pulmonary Infection Score (CPIS) (1), HME resistance after 24 hrs of use, endotracheal tube resistance, and HME use per patient. VAP occurred with similar frequency in all groups (13%, HME; 14%, DHW; 10%, SHW; p = 0.61) and was predicted only by current smoking (adjusted odds ratio [AOR], 2.1; 95% confidence interval [CI], 1.1-3.9; p =.03) and ventilation days (AOR, 1.05; 95% Cl, 1.0-1.2; p =.001); VAP was less likely for patients with an admission diagnosis of pneumonia (AOR, 0.40; 95% Cl, 0.4-0.2; p =.04). HME resistance after 24 hrs of use measured at a gas flow of 50 L/min was 0.9 cm H2O (0.4-2.9). Endotracheal tube resistance was similar for all three groups (16-19 cm H2O min/L; p =.2), as were suction frequency, secretion thickness, and blood on suctioning (p =.32, p =.06, and p =.34, respectively). The HME use per patient per day was 1.13. Conclusions: Humidification technique does not influence either VAP incidence or secretion characteristics, but HMEs may have air-flow resistance higher than manufacturer specifications after 24 hrs of use.

Flow patterns and performance of distillation trays

It is known that distillation tray efficiency depends on the liquid flow pattern, particularly for large diameter trays. Scale·up failures due to liquid channelling have occurred, and it is known that fitting flow control devices to trays sometirr.es improves tray efficiency. Several theoretical models which explain these observations have been published. Further progress in understanding is at present blocked by lack of experimental measurements of the pattern of liquid concentration over the tray. Flow pattern effects are expected to be significant only on commercial size trays of a large diameter and the lack of data is a result of the costs, risks and difficulty of making these measurements on full scale production columns. This work presents a new experiment which simulates distillation by water cooling. and provides a means of testing commercial size trays in the laboratory. Hot water is fed on to the tray and cooled by air forced through the perforations. The analogy between heat and mass transfer shows that the water temperature at any point is analogous to liquid concentration and the enthalpy of the air is analogous to vapour concentration. The effect of the liquid flow pattern on mass transfer is revealed by the temperature field on the tray. The experiment was implemented and evaluated in a column of 1.2 m. dia. The water temperatures were measured by thennocouples interfaced to an electronic computerised data logging system. The "best surface" through the experimental temperature measurements was obtained by the mathematical technique of B. splines, and presented in tenos of lines of constant temperature. The results revealed that in general liquid channelling is more imponant in the bubbly "mixed" regime than in the spray regime. However, it was observed that severe channelling also occurred for intense spray at incipient flood conditions. This is an unexpected result. A computer program was written to calculate point efficiency as well as tray efficiency, and the results were compared with distillation efficiencies for similar loadings. The theoretical model of Porter and Lockett for predicting distillation was modified to predict water cooling and the theoretical predictions were shown to be similar to the experimental temperature profiles. A comparison of the repeatability of the experiments with an errors analysis revealed that accurate tray efficiency measurements require temperature measurements to better than ± 0.1 °c which is achievable with conventional techniques. This was not achieved in this work, and resulted in considerable scatter in the efficiency results. Nevertheless it is concluded that the new experiment is a valuable tool for investigating the effect of the liquid flow pattern on tray mass transfer.

The durability of glass fibre reinforced cements made with new cementitious matrices

Widespread use of glass fibre reinforced cement (GRC) has been impeded by concerns over its durability. Three degradation mechanisms are proposed - fibre corrosion, Ca(OHh precipitation and matrix densification - although their relative importance is debated. Matrices with reduced alkalinities and Ca(OH)2 contents are being developed; the aim of this study was to investigate their hydration and interaction with alkali-resistant fibres to determine the factors controlling their long-term durability, and assess the relevancy of accelerated ageing. The matrices studied were: OPC/calcium-sulphoaluminate cement plus metakaolin (C); OPC plus metakaolin (M); blast-furnace slag cement plus a micro-silica based additive (D); and OPC (O). Accelerated ageing included hot water and cyclic regimes prior to tensile testing. Investigations included pore solution expression, XRD, DTA/TG, SEM and optical petrography. Bond strength was determined from crack spacings using microstructural parameters obtained from a unique image analysis technique. It was found that, for the new matrices - pore solution alkalinities were lower; Ca(OH)2 was absent or quickly consumed; different hydrates were formed at higher immersion temperatures; degradation under 65°C immersion was an order of magnitude slower, and no interfilamental Ca(OH)2 was observed .It was concluded that: fibre weakening caused by flaw growth was the primary degradation mechanism and was successfully modelled on stress corrosion/static fatigue principles. OPC inferiority was attributed partly to its higher alkalinity but chiefly to the growth of Ca(OH)2 aggravating the degradation; and hot water ageing although useful in model formulation and contrasting the matrices, changed the intrinsic nature of the composites rather than simply accelerating the degradation mechanisms.

Annealing effects on strain and stress sensitivity of polymer optical fibre based sensors

The annealing effects on strain and stress sensitivity of polymer optical fibre Bragg grating sensors after their photo-inscription are investigated. PMMA optical fibre based Bragg grating sensors are first photo-inscribed and then they were placed into hot water for annealing. Strain, stress and force sensitivity measurements are taken before and after annealing. Parameters such as annealing time and annealing temperature are investigated. The change of the fibre diameter due to water absorption and the annealing process is also considered. The results show that annealing the polymer optical fibre tends to increase the strain, stress and force sensitivity of the photo-inscribed sensor.

Sensitivity enhancement using annealed polymer optical fibre based sensors for pressure sensing applications

Thermal annealing can be used to induce a permanent negative Bragg wavelength shift for polymer fibre grating sensors and it was originally used for multiplexing purposes. Recently, researchers showed that annealing can also provide additional benefits, such as strain and humidity sensitivity enhancement and augmented temperature operational range. The annealing process can change both the optical and mechanical properties of the fibre. In this paper, the annealing effects on the stress and force sensitivities of PMMA fibre Bragg grating sensors are investigated. The incentive for that investigation was an unexpected behaviour observed in an array of sensors which were used for liquid level monitoring. One sensor exhibited much lower pressure sensitivity and that was the only one that was not annealed. To further investigate the phenomenon, additional sensors were photo-inscribed and characterised with regard their stress and force sensitivities. Then, the fibres were annealed by placing them in hot water, controlling with that way the humidity factor. After annealing, stress and force sensitivities were measured again. The results show that the annealing can improve the stress and force sensitivity of the devices. This can provide better performing sensors for use in stress, force and pressure sensing applications.

Review and analysis of solar thermal facades

Harnessing solar energy to provide for the thermal needs of buildings is one of the most promising solutions to the global energy issue. Exploiting the additional surface area provided by the building’s façade can significantly increase the solar energy output. Developing a range of integrated and adaptable products that do not significantly affect the building’s aesthetics is vital to enabling the building integrated solar thermal market to expand and prosper. This work reviews and evaluates solar thermal facades in terms of the standard collector type, which they are based on, and their component make-up. Daily efficiency models are presented, based on a combination of the Hottel Whillier Bliss model and finite element simulation. Novel and market available solar thermal systems are also reviewed and evaluated using standard evaluation methods, based on experimentally determined parameters ISO 9806. Solar thermal collectors integrated directly into the facade benefit from the additional wall insulation at the back; displaying higher efficiencies then an identical collector offset from the facade. Unglazed solar thermal facades with high capacitance absorbers (e.g. concrete) experience a shift in peak maximum energy yield and display a lower sensitivity to ambient conditions than the traditional metallic based unglazed collectors. Glazed solar thermal facades, used for high temperature applications (domestic hot water), result in overheating of the building’s interior which can be reduced significantly through the inclusion of high quality wall insulation. For low temperature applications (preheating systems), the cheaper unglazed systems offer the most economic solution. The inclusion of brighter colour for the glazing and darker colour for the absorber shows the lowest efficiency reductions (<4%). Novel solar thermal façade solutions include solar collectors integrated into balcony rails, shading devices, louvers, windows or gutters.