Aquisição por Visão Artificial e Medição Automática de Micro Dureza Vickers

O ensaio de dureza, e mais concretamente o ensaio de micro dureza Vickers, é no universo dos ensaios mecânicos um dos mais utilizados quer seja na indústria, no ensino ou na investigação e desenvolvimento de produto no âmbito das ciências dos materiais. Na grande maioria dos casos, a utilização deste ensaio tem como principal aplicação a caracterização ou controlo da qualidade de fabrico de materiais metálicos. Sendo um ensaio de relativa simplicidade de execução, rapidez e com resultados comparáveis e relacionáveis a outras grandezas físicas das propriedades dos materiais. Contudo, e tratando-se de um método de ensaio cuja intervenção humana é importante, na medição da indentação gerada por penetração mecânica através de um sistema ótico, não deixa de exibir algumas debilidades que daí advêm, como sendo o treino dos técnicos e respetivas acuidades visuais, fenómenos de fadiga visual que afetam os resultados ao longo de um turno de trabalho; ora estes fenómenos afetam a repetibilidade e reprodutibilidade dos resultados obtidos no ensaio. O CINFU possui um micro durómetro Vickers, cuja realização dos ensaios depende de um técnico treinado para a execução do mesmo, apresentando todas as debilidades já mencionadas e que o tornou elegível para o estudo e aplicação de uma solução alternativa. Assim, esta dissertação apresenta o desenvolvimento de uma solução alternativa ao método ótico convencional na medição de micro dureza Vickers. Utilizando programação em LabVIEW da National Instruments, juntamente com as ferramentas de visão computacional (NI Vision), o programa começa por solicitar ao técnico a seleção da câmara para aquisição da imagem digital acoplada ao micro durómetro, seleção do método de ensaio (Força de ensaio); posteriormente o programa efetua o tratamento da imagem (aplicação de filtros para eliminação do ruído de fundo da imagem original), segue-se, por indicação do operador, a zona de interesse (ROI) e por sua vez são identificadas automaticamente os vértices da calote e respetivas distâncias das diagonais geradas concluindo, após aceitação das mesmas, com o respetivo cálculo de micro dureza resultante. Para validação dos resultados foram utilizados blocos-padrão de dureza certificada (CRM), cujos resultados foram satisfatórios, tendo-se obtido um elevado nível de exatidão nas medições efetuadas. Por fim, desenvolveu-se uma folha de cálculo em Excel com a determinação da incerteza associada às medições de micro dureza Vickers. Foram então comparados os resultados nas duas metodologias possíveis, pelo método ótico convencional e pela utilização das ferramentas de visão computacional, tendo-se obtido bons resultados com a solução proposta.

A Metrologia na Indústria Aeronáutica

O presente relatório é um dos elementos que contribuirão para a concretização da avaliação individual da Unidade Curricular de Dissertação/Projeto/Estágio Profissional, inserida no plano de estudos do Mestrado em Engenharia de Instrumentação e Metrologia e traduz o trabalho realizado na empresa Caetano Aeronautic. O estágio, com a duração de sete meses, permitiu a concretização de finalidades e objetivos que deram suporte ao desenvolvimento das aprendizagens e mobilização dos saberes científicos relativos a domínios e conteúdos curriculares, nomeadamente inseridos nas áreas da Metrologia e Qualidade. A Metrologia é circunscrita como a ciência da medição. A medição é uma operação de extrema relevância em diversas atividades, porque é através da Metrologia que se garante um elevado nível de qualidade pretendido para a conceção, fabricação e utilização de serviços ou produtos. Face à indústria aeronáutica envolver um elevado conjunto de processos, de normas e documentação, foi necessário inicialmente um envolvimento integrado com o Sistema de Gestão da Qualidade da Caetano Aeronautic e com as operações inerentes, nomeadamente de melhoria contínua. Foram desenvolvidas, dentro do possível, propostas de melhoria no processo de inspeção dos componentes aeronáuticos. Dentro das mesmas destacam-se a alteração dos registos de medição, o estudo e posterior proposta de aquisição de ferramentas adicionais para equipamentos de medição. O fluxo de medição tornou-se mais fluído através da concretização da proposta de alteração do layout do laboratório. De salientar o trabalho desenvolvido na área da Engenharia da Qualidade, nomeadamente no tratamento de não conformidades, o que contribuiu para que o processo se encontre atualmente bastante simplificado na empresa.

Estudo do Aborto Recorrente. Ainda há Lugar para a Histerossalpingografia?

Overview and Aims: The investigation of recurrent miscarriage includes the study of uterine morphology. 3D ultrasound allows the evaluation of the morphology (cavity and outer contour), reducing the need for invasive tests such as hystero - salpingography (HSG), hysteroscopy and laparoscopy. We evaluated the diagnostic agreement between HSG and 3D ultrasound in the study of the uterine cavity morphology. Study Design: Prospective study. Population: A total of 34 women referred to our institution with a history of recurrent miscarriage. Methods: To compare the results of 3D ultrasound and HSG, all women underwent both exams. 3D scans were performed by the same operator and HSG were evaluated by the same clinician. The concordance study was performed using the Kappa coefficient. Results: With 3D ultrasound and HSG, uterine anomalies were diagnosed in 52.9% (18/34) and 47% (16/34) of the cases and congenital malformations were the most frequent findings. The agreement between the two techniques was excellent(K = 0.825). The three cases of diagnostic disagreement were analyzed. Conclusion: A high level of diagnostic agreement was observed between HSG and 3D ultrasound. The 3D ultrasound, a low cost and well tolerated technique, when performed by an experienced operator, is the first line exam to study the uterine morphology in women with recurrent miscarriage.

Perinatal Ischemic Stroke: a Five-Year Retrospective Study in a Level-III Maternity

Objective To study the incidence, clinical presentation, risk factors, imaging diagnosis, and clinical outcome of perinatal stroke. Methods Data was retrospectively collected from full-term newborns admitted to the neonatal unit of a level III maternity in Lisbon with cerebral stroke, from January 2007 to December 2011. Results There were 11 cases of stroke: nine were arterial ischemic stroke and two were cerebral venous sinus thrombosis. We estimated an incidence of arterial ischemic stroke of 1.6/5,000 births and of cerebral venous sinus thrombosis of 7.2/100,000 births. There were two cases of recurrent stroke. Eight patients presented with symptoms while the remaining three were asymptomatic and incidentally diagnosed. The most frequently registered symptoms (8/11) were seizures; in that, generalized clonic (3/8) and focal clonic (5/8). Strokes were more commonly left-sided (9/11), and the most affected artery was the left middle cerebral artery (8/11). Transfontanelle ultrasound was positive in most of the patients (10/11), and stroke was confirmed by cerebral magnetic resonance in all patients. Electroencephalographic recordings were carried out in five patients and were abnormal in three (focal abnormalities n=2, burst-suppression pattern n=1). Eight patients had previously identified risk factors for neonatal stroke which included obstetric and neonatal causes. Ten patients were followed up at outpatients setting; four patients developed motor deficits and one presented with epilepsy. Conclusions Although a modest and heterogeneous sample, this study emphasizes the need for a high level of suspicion when it comes to neonatal stroke, primarily in the presence of risk factors. The prevalence of neurological sequelae in our series supports the need of long-term follow-up and early intervention strategies.

Petri net based development of globally-asynchronous locally-synchronous distributed embedded systems

Dissertação para obtenção do Grau de Doutor em Engenharia Electrotécnica e de Computadores

A framework for efficient model transformations

The reported productivity gains while using models and model transformations to develop entire systems, after almost a decade of experience applying model-driven approaches for system development, are already undeniable benefits of this approach. However, the slowness of higher-level, rule based model transformation languages hinders the applicability of this approach to industrial scales. Lower-level, and efficient, languages can be used but productivity and easy maintenance seize to exist. The abstraction penalty problem is not new, it also exists for high-level, object oriented languages but everyone is using them now. Why is not everyone using rule based model transformation languages then? In this thesis, we propose a framework, comprised of a language and its respective environment, designed to tackle the most performance critical operation of high-level model transformation languages: the pattern matching. This framework shows that it is possible to mitigate the performance penalty while still using high-level model transformation languages.

Automatic generation of ETL physical systems from BPMN conceptual models

ETL conceptual modeling is a very important activity in any data warehousing system project implementation. Owning a high-level system representation allowing for a clear identification of the main parts of a data warehousing system is clearly a great advantage, especially in early stages of design and development. However, the effort to model conceptually an ETL system rarely is properly rewarded. Translating ETL conceptual models directly into something that saves work and time on the concrete implementation of the system process it would be, in fact, a great help. In this paper we present and discuss a hybrid approach to this problem, combining the simplicity of interpretation and power of expression of BPMN on ETL systems conceptualization with the use of ETL patterns to produce automatically an ETL skeleton, a first prototype system, which has the ability to be executed in a commercial ETL tool like Kettle.

Environmental determinants for natural regeneration of gallery forest at the Cerrado/Amazonia boundaries in Brazil

Natural regeneration and structure and their relationship to environmental variables were studied in three sections of a gallery forest, in Eastern Mato Grosso, Brazil (14º43′S and 52º21′W). The assumption was that natural regeneration is constrained by environmental determinants at all stages of development of the tree community. The objective was to analyse the forest structure and to verify the relationship between species distribution and abundance at different stages of regeneration and environmental variables. In each section, 47 contiguous (10x10m) permanent plots were established to sample trees (gbh≥15cm), following a systematic design. Seedlings (0.01 to 1m height), saplings (1.01 to 2m) and poles (from 2.01m height to gbh<15cm) were sampled in sub-plots of 1x1m, 2x2m and 5x5m, respectively. In each plot, soil properties, gaps projection, bamboos, rocky cover, declivity and depth of ground watertable were determined. The relationships between the environmental variables with trees and seedling communities were assessed by canonical correspondence analysis. In spite of the sections being near to each other, they presented large differences in floristics, structure and site conditions. The forest soil presented a low cation exchange capacity and a high level of Al saturation. The occurrence of bamboos and gaps and the depth of ground watertable limited the occurrence of poles and trees. The high degree of structural heterogeneity for each regeneration category was related primarily to a humidity gradient; but soil fertility (Ca+Mg) was also a determinant of seedling and sapling communities.

Characterization of the oculomotor alterations in inicial phase of Multiple Sclerosis

Dissertação de mestrado em Advanced Optometry

Contribuição para equipamento didático de máquina de medição por coordenadas

Dissertação de mestrado integrado em Engenharia Mecânica

Mejoramiento del comportamiento térmico de sistemas de calentamiento de agua solares termosifónicos hechos con materiales no convencionales y con tanques de almacenamiento verticales y horizontales Performance improvement of solar thermosyphonic systems for water heating made of non conventional materials and using horizontal and vertical storage tanks

El objeto de estudio de este proyecto son los sistemas de calentamiento de agua mediante energía solar que funcionan termosifónicamente. En particular se tratará con dos diseños particulares generados por fabricantes de la Provincia de Córdoba y que han solicitado el asesoramiento del Grupo de Energía Solar (GES) para el mejoramiento de la performance térmica de dichos equipos. Se trata de dos sistemas que tienen materiales no tradicionales y se diferencian además por tener una distinta disposición del tanque de almacenamiento: uno es en forma vertical y el otro en forma horizontal. Basados en los resultados de un ensayo bajo norma internacional, donde se detectaron algunas puntos factibles de mejora, se propone en este proyecto el análisis en detalle de los equipos, para lo cual se les debe desarmar completos, para realizar un estudio analítico y experimental de los mismos con el objeto de hacer un planteo teórico-analítico del comportamiento de los mismos, con la implementación de propuestas de mejora y chequeo de los resultados. Se propone entonces como objetivo lograr un mejoramiento de la performance térmica de los citados equipos a partir de un estudio experimental y analítico. Asumiendo esta posibilidad de mejora, se plantea la hipótesis de que es posible representar el funcionamiento de estos equipos mediante modelos físico-matemáticos desarrollados a partir de ecuaciones y correlaciones conocidas y procesos a interpretar mediante resoluciones numéricas y softwares específicos de simulación. De esta manera, se plantea el despieze completo de los equipos para estudiar en detalle su estructura y conexiones internas y a partir de la geometría, dimensiones y propiedades termofísicas de materiales constructivos y fluidos de trabajo, realizar modelos físico-matemáticos que permitan realizar variaciones de propiedades y geometría y así buscar las mejores combinaciones que produzcan equipos más eficientes térmicamente. Los modelos físico-matemáticos serán codificados en lenguajes de alto nivel para poder luego de una validación de los modelos, correr simulaciones en un software de reconocimiento internacional que permite sumar dichos modelos mediante un protocolo de comunicación, haciendo que las poderosas prestaciones del software se puedan aplicar a nuestros modelos. Se complementará el estudio con un análisis exergético para identificar los puntos críticos en que se producen las pérdidas de oportunidad de aprovechar la energía disponible, para así analizar cómo solucionar los problemas en dichos puntos. Los materiales a utilizar serán los propios equipos provistos por los fabricantes, que serán modificados convenientemente para operarlos como prototipos Se espera obtener un conocimiento acabado de los procesos y principios de funcionamiento de los equipos, que permita plantear las mejoras, las cuales se implementarán en los prototipos, realizándose una medición mediante norma igual a la inicial para ver en que magnitud se logran las mejoras esperadas. Se pretende además que las mejoras a implementar, en la etapa de transferencia a las empresas involucradas, redunden no sólo en un beneficio técnico, sino que también los sea desde el punto de vista económico. Para ello se trabajará también sobre los procesos y métodos de fabricación para que los equipos mejorados no sean mas caros que los originales y de ser posible sean aún más económicos, todo esto apuntando a la difusión de la energía solar térmica y poner al alcance de todos estos equipos tan convenientes para la propagación de las energías limpias. El proyecto redundará también en un importante beneficio para el conocimiento de la comunidad científica en general, con el aporte de nuevos resultados en diseños novedosos y con nuevos materiales. Además, la institución se beneficiará con la formación que obtendrán los integrantes del proyecto, muchos de ellos en etapa de realización de sus estudios de posgrado y en una etapa importante de su vida como investigadores. The main goal of this project is the improvement of two thermosyphonic solar water heating systems, made of non conventional materials and with different arrangement of their storage tanks: one is vertical and the other one horizontal. The thermosyphonic systems are provided by manufacturers of the Córdoba Province, who came to the Solar Energy Group (GES) of the National University of Río Cuarto looking for help for the design of their products. In an agreement with these manufacturers, it was proposed this project in order to work analytically and experimentally in order to obtain physical-mathematical models of these two systems, which allow for changes to look by means of simulations the best changes to implement on the equipments for the improvement of their thermal performance. Then, the materials to be used are the proper systems provided by the manufacturers, which will be disarmed to be studied in detail. After the analytical study the proposals of improvement will be implemented in a high level language of programming to perform simulations in the environment of a well-known software for energy simulations (TRNSYS). After the simulations, the best modifications will be physically implemented in the prototypes to perform finally the same normalized test of the beginning and check the magnitude of the implemented improvements. The importance of this project is based on the offer of better systems the companies would make, which would benefit the deployment of the thermal solar energy. Another relevant point is to make the new equipments at the same cost of the previous ones or cheaper, in order to achieve a good deployment of the solar water heating systems; then, the manufacture processes and methods must be studied to obtain not only good technical solutions, but also economical equipments. In addition, this project will contribute to the increasing of the knowledge in the area of thermosyphonic solar systems and the training of postgraduate students.

Efeitos de diferentes níveis de N, P e K sôbre cacaueiros jovens (Theorema cacao L.) em solução nutritiva

Cocoa seedlings were grown in nutrient solution in order to find out the effects of the levels of N, P, K in the substrate on growth, symptoms and chemical composition of the leaves. A 3x3x3 factorial design was used. The following conclusions can be drawn. 5.1. Among the three elements under study, only nitrogen had a positive, significant effect on growth as measured by height and dry weight. 5.2. The level of a given elements in the leaves did increase when its level in the nutrient solution was raised. On the other hand the N content was positively affected by the concentration of P in the substrate. 5.3. A decrease in the N/P and K/P rations in the leaves was observed when the nutrient solutions had, res-respectively, absence of K and N and high level both of K and N. The N/K ratio increased with the level of P in the substrate. 5.4 A highly significant positive correlation was found between N content in the leaves and dry weight. This was not the case however, insofar P and K are considered - no correlation whatsoever was observed.

GNSS array: diseño de una antena con polarización circular

Aquest projecte es centra en el disseny d’una antena microstrip per a GNSS. Una antena per a GNSS ha de tenir adaptació de impedància d’entrada i polarització circular a dretes, com a principals especificacions, en el rang de 1.15-1.6 GHz. El tipus d’alimentació d’una antena microstrip amb el major ample de banda d’adaptació és l’alimentació mitjançant acoblament per apertura. Si a l’antena s’introdueixen dos apertures de forma ortogonal, alimentades amb un desfasament de 90º entre elles, s’aconsegueix polarització circular. L’opció de separar les apertures redueix la transferència de potència entre elles, i disminueix el guany de polarització creuada. La xarxa d’alimentació dissenyada és un divisor de Wilkinson amb una línia de λ/4 a la freqüència central, encara que el desfasament als extrems de la banda no sigui de 90º. Com a xarxa d’alimentació es va provar un hibrid de 90º, però l’elevat valor del paràmetre S21 de l’antena impossibilita l’adaptació a l’entrada del hibrid.

Utilització del robot mòbil com a eina d'aprenentatge en ensenyaments tècnics

En aquest Projecte de Millora de la Qualitat Docent es descriu el disseny, la construcció i la utilització d’un robot mòbil com a eina docent en titulacions d’Enginyeria. El robot mòbil té com a element de control un PC portàtil convencional per tal de facilitar el procés d’aprenentatge de l’alumnat estigui centrat en l’objectiu de les pràctiques i no en el funcionament i control del robot. A més a més, el robot disposa d’un elevat nombre de sensors i actuadors per tal d’oferir un elevat grau d’interdisciplinaritat.

Scheduling in virtual infrastructure

For the execution of the scientific applications, different methods have been proposed to dynamically provide execution environments for such applications that hide the complexity of underlying distributed and heterogeneous infrastructures. Recently virtualization has emerged as a promising technology to provide such environments. Virtualization is a technology that abstracts away the details of physical hardware and provides virtualized resources for high-level scientific applications. Virtualization offers a cost-effective and flexible way to use and manage computing resources. Such an abstraction is appealing in Grid computing and Cloud computing for better matching jobs (applications) to computational resources. This work applies the virtualization concept to the Condor dynamic resource management system by using Condor Virtual Universe to harvest the existing virtual computing resources to their maximum utility. It allows existing computing resources to be dynamically provisioned at run-time by users based on application requirements instead of statically at design-time thereby lay the basis for efficient use of the available resources, thus providing way for the efficient use of the available resources.