Optical demultiplexer device operating in the visible spectrum

In this paper, we present results on the use of multilayered a-SiC:H heterostructures as a device for wavelength-division demultiplexing of optical signals. These devices are useful in optical communications applications that use the wavelength division multiplexing technique to encode multiple signals into the same transmission medium. The device is composed of two stacked p-i-n photodiodes, both optimized for the selective collection of photo generated carriers. Band gap engineering was used to adjust the photogeneration and recombination rate profiles of the intrinsic absorber regions of each photodiode to short and long wavelength absorption in the visible spectrum. The photocurrent signal using different input optical channels was analyzed at reverse and forward bias and under steady state illumination. A demux algorithm based on the voltage controlled sensitivity of the device was proposed and tested. An electrical model of the WDM device is presented and supported by the solution of the respective circuit equations.

The influence of genetic polymorphisms in XRCC3 and ADH5 genes on the frequency of genotoxicity biomarkers in workers exposed to formaldehyde

The International Agency for Research on Cancer classified formaldehyde as carcinogenic to humans because there is “sufficient epidemiological evidence that it causes nasopharyngeal cancer in humans”. Genes involved in DNA repair and maintenance of genome integrity are critically involved in protecting against mutations that lead to cancer and/or inherited genetic disease. Association studies have recently provided evidence for a link between DNA repair polymorphisms and micronucleus (MN) induction. We used the cytokinesis-block micronucleus (CBMN assay) in peripheral lymphocytes and MN test in buccal cells to investigate the effects of XRCC3 Thr241Met, ADH5 Val309Ile, and Asp353Glu polymorphisms on the frequency of genotoxicity biomarkers in individuals occupationally exposed to formaldehyde (n = 54) and unexposed workers (n = 82). XRCC3 participates in DNA double-strand break/recombination repair, while ADH5 is an important component of cellular metabolism for the elimination of formaldehyde. Exposed workers had significantly higher frequencies (P < 0.01) than controls for all genotoxicity biomarkers evaluated in this study. Moreover, there were significant associations between XRCC3 genotypes and nuclear buds, namely XRCC3 Met/Met (OR = 3.975, CI 1.053–14.998, P = 0.042) and XRCC3 Thr/Met (OR = 5.632, CI 1.673–18.961, P = 0.005) in comparison with XRCC3 Thr/Thr. ADH5 polymorphisms did not show significant effects. This study highlights the importance of integrating genotoxicity biomarkers and genetic polymorphisms in human biomonitoring studies.

Transformations induced in bulk amorphous silica by ultrafast laser direct writingTransformations induced in bulk amorphous silica by ultrafast laser direct writing

Agências Financiadoras: Fundação para a Ciência e a Tecnologia - PTDC/FIS/102127/2008 e PTDC/FIS/102127/2008 e SFRH/BPD/78871/2011; Spanish Ministerio de Ciencia e Innovacion - FUNCOAT-CSD2008-00023-CONSOLIDER; Instituto Superior Técnico;

Cu2ZnSnS4 absorber layers obtained through sulphurization of metallic precursors: Graphite box versus sulphur flux

In this work we employed a hybrid method, combining RF-magnetron sputtering with evaporation, for the deposition of tailor made metallic precursors, with varying number of Zn/Sn/Cu (ZTC) periods and compared two approaches to sulphurization. Two series of samples with 1×, 2× and 4× ZTC periods have been prepared. One series of precursors was sulphurized in a tubular furnace directly exposed to a sulphur vapour and N2+5% H2 flux at a pressure of 5.0×10+4 Pa. A second series of identical precursors was sulphurized in the same furnace but inside a graphite box where sulphur pellets have been evaporated again in the presence of N2+5% H2 and at the same pressure as for the sulphur flux experiments. The morphological and chemical analyses revealed a small grain structure but good average composition for all three films sulphurized in the graphite box. As for the three films sulphurized in sulphur flux grain growth was seen with the increase of the number of ZTC periods whilst, in terms of composition, they were slightly Zn poor. The films' crystal structure showed that Cu2ZnSnS4 is the dominant phase. However, in the case of the sulphur flux films SnS2 was also detected. Photoluminescence spectroscopy studies showed an asymmetric broad band emission whichoccurs in the range of 1–1.5 eV. Clearly the radiative recombination efficiency is higher in the series of samples sulphurized in sulphur flux. We have found that sulphurization in sulphur flux leads to better film morphology than when the process is carried out in a graphite box in similar thermodynamic conditions. Solar cells have been prepared and characterized showing a correlation between improved film morphology and cell performance. The best cells achieved an efficiency of 2.4%.

Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

Demux devices based on A-SiC:H

In this paper we present results about the functioning of a multilayered a-SiC:H heterostructure as a device for wavelength-division demultiplexing of optical signals. The device is composed of two stacked p-i-n photodiodes, both optimized for the selective collection of photogenerated carriers. Band gap engineering was used to adjust the photogeneration and recombination rates profiles of the intrinsic absorber regions of each photodiode to short and long wavelength absorption and carrier collection in the visible spectrum. The photocurrent signal using different input optical channels was analyzed at reverse and forward bias and under steady state illumination. This photocurrent is used as an input for a demux algorithm based on the voltage controlled sensitivity of the device. The device functioning is explained with results obtained by numerical simulation of the device, which permit an insight to the internal electric configuration of the double heterojunction.These results address the explanation of the device functioning in the frequency domain to a wavelength tunable photocapacitance due to the accumulation of space charge localized at the internal junction. The existence of a direct relation between the experimentally observed capacitive effects of the double diode and the quality of the semiconductor materials used to form the internal junction is highlighted.

Susceptibilidade genética para cancro da mama

RESUMO: O cancro da mama é a patologia oncológica mais frequente nas mulheres sendo o responsável pela maior taxa de mortalidade por cancro no sexo feminino. Contudo, as causas inerentes a esta patologia permanecem por esclarecer. Nos últimos anos tem-se verificado que o risco para patologia neoplásica depende de factores ambientais e genéticos, estando estes últimos associados à variabilidade genética inter-individual. Polimorfismos genéticos em genes envolvidos no metabolismo de hormonas sexuais, de cancerígenos ambientais e na reparação da lesão genética, são potenciais candidatos a estarem associados à susceptibilidade individual para esta patologia. Assim, neste trabalho desenvolveram-se estudos de associação caso-controlo na população Portuguesa, com vista a avaliar-se o papel atribuído aos polimorfismos na susceptibilidade para cancro da mama. Foram seleccionados polimorfismos em genes envolvidos em diferentes vias mecanicistas: destoxificação de cancerígenos, metabolismo de estrogénios, reparação por excisão de bases, reparação por excisão de nucleótidos, reparação mismatch e reparação por recombinação homóloga. Os resultados obtidos revelaram associação entre os seguintes polimorfismos e a susceptibilidade individual para cancro da mama: os dois SNPs estudados no gene XRCC1 (Arg194Trp e Arg399Gln) e o SNP no gene XRCC3 (Thr241Met) após estratificação pelo status menopausico. Mediante estratificação por status de amamentação os SNPs identificados nos genes MnSOD (Val16Ala) e XRCC2 (Arg118His); um SNP no gene MLH3 (Leu844Pro), e por fim como resultado de interacção gene-gene as interacções descritas por MSH3 Ala1045Thr/MSH6 Gly39Glu e MSH4 Ala97Thr/MLH3 Leu844Pro. Os resultados obtidos e apresentados na presente dissertação, revelam que o estudo de polimorfismos pode representar um papel determinante na etiologia do cancro da mama. No entanto, mais estudos envolvendo estes mesmos polimorfismos em populações casuisticamente superiores serão uma mais-valia nos estudos de associação para esta neoplasia. Adicionalmente, a utilização da metodologia de Pools de DNA, poderá ser uma ferramenta útil na pré-selecção dos polimorfismos mais relevantes a estudar, na medida em que permite estimar a frequência alélica de cada SNP numa determinada população.-----------------------------------ABSTRACT: Breast cancer is the most common form of cancer among women, being the responsible for the highest mortality rate from cancer among the female sex. However, the main causes related to this pathology remain unclear. The risk of neoplasic disease has been connected with genetic and environmental factors. In fact, genes and the environment share the stage for most, if not all, common non-familial cancers, and are related to individual susceptibility. Genetic polymorphisms identified in genes encoding enzymes involved in estrogen metabolism, xenobiotics and DNA repair pathways are believed to be candidates for associations with breast cancer. Therefore, it was our intention to develop case-control studies among the Portuguese population, in order to evaluate the potential role of several genetic polymorphisms in breast cancer susceptibility. We selected polymorphisms in genes involved in different pathways: carcinogenic detoxification, estrogen metabolism, base excision repair, nucleotide excision repair, mismatch repair and double strand break repair by homologous recombination. The results obtained revealed potential associations between some polymorphisms studied and individual susceptibility to breast cancer. Regarding this fact, our results suggest the potential involvement of two XRCC1 gene polymorphisms (Arg194Trp and Arg399Gln) and XRCC3 gene polymorphism (Thr241Met) after stratification to menopausal status and after stratification to breastfeeding status an association of MnSOD gene polymorphism (Val16Ala) and XRCC2 (Arg188His) with the disease. The SNP identified in MLH3 gene (Leu844Pro), and the interaction gene-gene described by MSH3 Ala1045Thr/MSH6 Gly39Glu and MSH4 Ala97Thr/MLH3 Leu844Pro were also related to breast cancer susceptibility. The results shown in the present dissertation have revealed the potential role of polymorphisms in breast cancer etiology. However, further studies will be needed with larger populations to confirm these results. Additionally, the use of DNA pools methodology, as a pre-selection tool, could allow the identification of the most relevant polymorphisms to be studied, estimating the allelic frequency of each SNPs in different populations.

A comparison between thin film solar cells made from co-evaporated CuIn1-xGaxSe2using a one-stage process versus a three-stage process

Until this day, the most efficient Cu(In,Ga)Se2 thin film solar cells have been prepared using a rather complex growth process often referred to as three-stage or multistage. This family of processes is mainly characterized by a first step deposited with only In, Ga and Se flux to form a first layer. Cu is added in a second step until the film becomes slightly Cu-rich, where-after the film is converted to its final Cu-poor composition by a third stage, again with no or very little addition of Cu. In this paper, a comparison between solar cells prepared with the three-stage process and a one-stage/in-line process with the same composition, thickness, and solar cell stack is made. The one-stage process is easier to be used in an industrial scale and do not have Cu-rich transitions. The samples were analyzed using glow discharge optical emission spectroscopy, scanning electron microscopy, X-ray diffraction, current–voltage-temperature, capacitance-voltage, external quantum efficiency, transmission/reflection, and photoluminescence. It was concluded that in spite of differences in the texturing, morphology and Ga gradient, the electrical performance of the two types of samples is quite similar as demonstrated by the similar J–V behavior, quantum spectral response, and the estimated recombination losses.

Novel functions of the cohesin accessory factor dPDS5 uncover a new meiotic checkpoint

Dissertation presented to obtain the Ph.D degree in Biology.

Design of a tool to study the fate of Chlamydia trachomatis infected cells

Chlamydia trachomatis has a unique obligate intracellular developmental cycle that ends by the lysis of the cell and/or the extrusion of the bacteria in order to allow for re-infections. While Chlamydia trachomatis infections are often asymptomatic the diagnosis of Chlamydia trachomatis is usually late, occurring after manifestation of persistency. Investigations on the consequences of long-term infections and the molecular mechanisms behind it will reveal light to what extent bacteria can modulate host cell function and what the ultimate fate of host cells after clearance of an infection is. Such studies on the host cell fate could be greatly facilitated if the infected cells become permanently marked during and after the infection. Therefore, this project intends to develop a new genetic tool that would allow permanently labeling of Chlamydia trachomatis host cells. The plan was to generate a Chlamydia trachomatis strain that encodes a recombinant CRE recombinase, fused to a secretory effector function of the Chlamydia type 3 secretion system (T3SS). Upon translocation into the host cell, this recombinant CRE enzyme could then, owing to its site-specific recombination function, switch a reporter gene contained in the host cell genome. To this end, the reporter line carried a membrane-tagged tdTomato (mT) gene flanked by two LoxP sequences followed by a GFP gene. The translocation of the recombinant CRE recombinase into this cell line was designed to trigger the recombination of the LoxP sites whereby the cells would turn from red fluorescence to green as an irreversible label of the infected cells. Successful execution of this mechanism would allow to draw a direct link between Chlamydia trachomatis infection and the subsequent fate of the infected cell.

Impact of chromossomal structure on the evolution of Schizosaccharomyces pombe undergoing Mutation Accumulation

Large chromosomal rearrangements are common in natural populations and thought to be involved in speciation events. In this project, we used experimental evolution to determine how the speed of evolution and the type of accumulated mutations depend on the ancestral chromosomal structure and genotype. We utilized two Wild Type strains and a set of genetically engineered Schizosaccharomyces pombe strains, different solely in the presence of a certain type of chromosomal variant (inversions or translocations), along with respective controls. Previous research has shown that these chromosomal variants have different fitness levels in several environments, probably due to changes in the gene expression along the genome. These strains were propagated in the laboratory at very low population sizes, in which we expect natural selection to be less efficient at purging deleterious mutations. We then measured these strains’ changes in fitness throughout this accumulation of deleterious mutations, comparing the evolutionary trajectories in the different rearrangements to understand if the chromosomal structure affected the speed of evolution. We also tested these mutations for possible epistatic effects and estimated their parameters: the number of arising deleterious mutations per generation (Ud) and each one’s mean effect (sd).

Ancestry of the Brazilian TP53 c.1010G>A (p.Arg337His, R337H) founder mutation : clues from haplotyping of short tandem repeats on Chromosome 17p

Rare germline mutations in TP53 (17p13.1) cause a highly penetrant predisposition to a specific spectrum of early cancers, defining the Li-Fraumeni Syndrome (LFS). A germline mutation at codon 337 (p.Arg337His, c1010G>A) is found in about 0.3% of the population of Southern Brazil. This mutation is associated with partially penetrant LFS traits and is found in the germline of patients with early cancers of the LFS spectrum unselected for familial his- tory. To characterize the extended haplotypes carrying the mutation, we have genotyped 9 short tandem repeats on chromosome 17p in 12 trios of Brazilian p.Arg337His carriers. Results confirm that all share a common ancestor haplotype of Caucasian/Portuguese-Ibe- ric origin, distant in about 72–84 generations (2000 years assuming a 25 years intergenera- tional distance) and thus pre-dating European migration to Brazil. So far, the founder p. Arg337His haplotype has not been detected outside Brazil, with the exception of two resi- dents of Portugal, one of them of Brazilian origin. On the other hand, increased meiotic recombination in p.Arg337His carriers may account for higher than expected haplotype diversity. Further studies comparing haplotypes in populations of Brazil and of other areas of Portuguese migration are needed to understand the historical context of this mutation in Brazil.

Flippase (FLP) recombinase-mediated marker recycling in the dermatophyte Arthroderma vanbreuseghemii.

Biological processes can be elucidated by investigating complex networks of relevant factors and genes. However, this is not possible in species for which dominant selectable markers for genetic studies are unavailable. To overcome the limitation in selectable markers for the dermatophyte Arthroderma vanbreuseghemii (anamorph: Trichophyton mentagrophytes), we adapted the flippase (FLP) recombinase-recombination target (FRT) site-specific recombination system from the yeast Saccharomyces cerevisiae as a selectable marker recycling system for this fungus. Taking into account practical applicability, we designed FLP/FRT modules carrying two FRT sequences as well as the flp gene adapted to the pathogenic yeast Candida albicans (caflp) or a synthetic codon-optimized flp (avflp) gene with neomycin resistance (nptII) cassette for one-step marker excision. Both flp genes were under control of the Trichophyton rubrum copper-repressible promoter (PCTR4). Molecular analyses of resultant transformants showed that only the avflp-harbouring module was functional in A. vanbreuseghemii. Applying this system, we successfully produced the Ku80 recessive mutant strain devoid of any selectable markers. This strain was subsequently used as the recipient for sequential multiple disruptions of secreted metalloprotease (fungalysin) (MEP) or serine protease (SUB) genes, producing mutant strains with double MEP or triple SUB gene deletions. These results confirmed the feasibility of this system for broad-scale genetic manipulation of dermatophytes, advancing our understanding of functions and networks of individual genes in these fungi.

Phenotypic consequences of copy number variation: insights from Smith-Magenis and Potocki-Lupski syndrome mouse models.

A large fraction of genome variation between individuals is comprised of submicroscopic copy number variation of genomic DNA segments. We assessed the relative contribution of structural changes and gene dosage alterations on phenotypic outcomes with mouse models of Smith-Magenis and Potocki-Lupski syndromes. We phenotyped mice with 1n (Deletion/+), 2n (+/+), 3n (Duplication/+), and balanced 2n compound heterozygous (Deletion/Duplication) copies of the same region. Parallel to the observations made in humans, such variation in gene copy number was sufficient to generate phenotypic consequences: in a number of cases diametrically opposing phenotypes were associated with gain versus loss of gene content. Surprisingly, some neurobehavioral traits were not rescued by restoration of the normal gene copy number. Transcriptome profiling showed that a highly significant propensity of transcriptional changes map to the engineered interval in the five assessed tissues. A statistically significant overrepresentation of the genes mapping to the entire length of the engineered chromosome was also found in the top-ranked differentially expressed genes in the mice containing rearranged chromosomes, regardless of the nature of the rearrangement, an observation robust across different cell lineages of the central nervous system. Our data indicate that a structural change at a given position of the human genome may affect not only locus and adjacent gene expression but also "genome regulation." Furthermore, structural change can cause the same perturbation in particular pathways regardless of gene dosage. Thus, the presence of a genomic structural change, as well as gene dosage imbalance, contributes to the ultimate phenotype.

A New Large-DNA-Fragment Delivery System Based on Integrase Activity from an Integrative and Conjugative Element.

During the past few decades, numerous plasmid vectors have been developed for cloning, gene expression analysis, and genetic engineering. Cloning procedures typically rely on PCR amplification, DNA fragment restriction digestion, recovery, and ligation, but increasingly, procedures are being developed to assemble large synthetic DNAs. In this study, we developed a new gene delivery system using the integrase activity of an integrative and conjugative element (ICE). The advantage of the integrase-based delivery is that it can stably introduce a large DNA fragment (at least 75 kb) into one or more specific sites (the gene for glycine-accepting tRNA) on a target chromosome. Integrase recombination activity in Escherichia coli is kept low by using a synthetic hybrid promoter, which, however, is unleashed in the final target host, forcing the integration of the construct. Upon integration, the system is again silenced. Two variants with different genetic features were produced, one in the form of a cloning vector in E. coli and the other as a mini-transposable element by which large DNA constructs assembled in E. coli can be tagged with the integrase gene. We confirmed that the system could successfully introduce cosmid and bacterial artificial chromosome (BAC) DNAs from E. coli into the chromosome of Pseudomonas putida in a site-specific manner. The integrase delivery system works in concert with existing vector systems and could thus be a powerful tool for synthetic constructions of new metabolic pathways in a variety of host bacteria.