Electrochemical and physical characterization of Ni-Cu-Fe alloy for chlor-alkali hydrogen cathodes

This work describes the development of an alternative acetate bath for the electrochemical codeposition of Ni-Cu-Fe electrodes at low pH that is stable for several weeks and produces electrodes with good performance for chlor-alkali electrolysis. Physical characterization of the electrode surface was made using X ray absorption spectroscopy (XAS), scanning electron microscopy (SEM) and energy dispersive analysis (EDX). The evaluation of the material as electrocatalyst for the hydrogen evolution reaction (her) was carried out in brine solution (160 g L-1 NaCl + 150 g L-1 NaOH) at different temperatures through steady-state polarization curves. The Ni-Cu-Fe electrodes obtained with this bath have shown low overpotentials for the her, around 0.150 V at 353 K, and good stability under continuous long-term operation for 260 hours. One positive aspect of this cathode is that the polarization behavior of the material shows only one Tafel slope over the temperature range of 298 - 353 K.

Reatividade do [Fe(CO)2(eta2-CS2)(PPh 3)2] frente a compostos de Cu(I): síntese de espécies binucleares heterometálicas contendo CS2 em ponte entre Fe(0) e Cu(I)

Este trabalho contempla a síntese e caracterização espectroscópica de dois compostos carbonílicos heterometálicos do tipo [Fe(CO)3(m-CS2)(PPh3 )(CuX)], X = Cl, ClO4. Os dados provenientes da espectroscopia no infravermelho e de RMN de 31P{¹H} foram conclusivos quanto à proposição da geometria octaédrica distorcida ao redor do átomo de ferro (0), como também sobre a natureza bimetálica de ambos compostos. Estes dados esclareceram o modo de coordenação dos grupos carbonilos, da trifenilfosfina (PPh3), bem como a disposição do ligante dissulfeto de carbono em ponte entre os átomos de Fe (0) e Cu (I).

Synthesis and characterization of Fe(III)-doped ceramic membranes of titanium dioxide and its application in photoelectrocatalysis of a textile dye

Pure and Fe(III)-doped TiO2 suspensions were prepared by the sol gel method with the use of titanium isopropoxide (Ti(OPri)4) as precursor material. The properties of doped materials were compared to TiO2 properties based on the characterization by thermal analysis (TG-DTA and DSC), X-ray powder diffractometry and spectroscopy measurements (FTIR). Both undoped and doped TiO2 suspensions were used to coat metallic substrate as a mean to make thin-film electrodes. Thermal treatment of the precursors at 400ºC for 2 h in air resulted in the formation of nanocrystalline anatase TiO2. The thin-film electrodes were tested with respect to their photocatalytic performance for degradation of a textile dye in aqueous solution. The plain TiO2 remains as the best catalyst at the conditions used in this report.

Gutenberg 1900:57

Gutenberg-lehti ilmestyi vuosina 1893-1915. Se oli perustettu ammattilehdeksi ja yhdyssiteeksi Suomen kirjanpainajille sekä äänenkannattajaksi Suomen kirjaltajaliitolle.

Hymnus op. 57

Soitinnus: sellot (16).

Anaerobic biodigestion of pigs feces in the initial, growing and finishing stages fed with diets formulated with corn or sorghum

The objective of this study was to evaluate the quality and the production of biogas and biofertilizer obtained from biodigester supplied with pig feces in the initial, growing and finishing stages, fed with diets formulated based on corn or sorghum. Twenty bench biodigesters were used with hydraulic retention time of 30 days and daily loads that contained 4 to 6% of total solids (TS) and 3.6 to 5.2% of volatile solids (VS). In the effluent of the biodigesters, mean levels of TS were observed ranging between 1.6 and 2.0% and of VS between 1.2 and 1.6%. The mean reductions of TS were 57.7 to 64.7% and of VS from 61.7 to 69.0%, and there was only difference in the finishing phase, in which the major averages reductions were produced by the biodigesters supplied with feces from animals fed with diets based on corn. In biodigesters supplied with feces from animals in the initial and growing stages fed with diets based on corn, were observed higher average productions of biogas and the greatest average potentials of biogas production. The average potentials obtained were 0.033; 0.181; 0.685; 0.788 and 1.132 m³ per kg of affluent, manure, TS added, VS added and VS reduced, respectively. No differences were found on the average content of methane in the biogas between diets and stages. The average concentrations of nutrients N, P, K, Ca, Mg, Na, Fe, Mn, Zn and Cu in the biodigester affluent and effluent, ranged between diets and stages.

Operational parameters of soybean seeding in santa fe system

The use of no tillage system associated with the crop-livestock integration is an alternate managing that promotes the accumulation of dry matter in the soil, an essential fact to make the system sustainable and profitable. The aim of this study was to evaluate the operational performance of a planter-tractor set on maize straws intercropped with Urochloa, in different seeding modes. The soybean crop was seed on the intercropping of two forage species (Urochloa brizantha and Urochloa ruziziensis) in five cropping systems: MBL (Maize with Urochloa in the maize seeding row, mixed with base fertilizer and deposited at 0.10 m), MBE (Maize with Urochloa seeded between rows at the same day of seeding maize), MBC (Urochloa between rows of maize seeded with the covering fertilizer at the V4 stage), MBLA (Maize with Urochloa by broadcast seeding at the V4 stage ) and MS (Single Maize: control). The following variables were evaluated: dry mass of maize straw, dry mass of forages and total dry mass of straw; and for the operational parameters the speed of seeding, wheel slippage, traction force and average power at the drawbar. The results showed that the amount of straw produced by maize intercropping with Urochloa, interferes in the operational performance of the tractor-planter at the operation of soybean seeding, i.e., areas with higher amount of straw promote greater energy demand, as well as higher wheel slippage.

COD, TSS, nutrients and coliforms removals in UASB reactors in two stages treating swine wastewater

The performance of two upflow anaerobic sludge blanket (UASB) reactors was evaluated in pilot scale (908 and 188 L), installed in series (R1 and R2), fed with swine wastewater with TSS around 5 and 13 g L-1. The UASB reactors were submitted to HDT of 36 and 18 h with VOL of 5.5 to 34.4 g COD (L d)-1 in the R1 and HDT of 7.5 e 3.7 h with VOL from 5.1 to 45.2 g COD (L d)-1 in the R2. The average removal efficiencies of COD ranged from 55 to 85% in the R1 and from 43 to 57% in the R2, resulting in values from 82 to 93% in the UASB reactors in two stage. Methane concentrations in the biogas were 69 to 74% with specific production from 0.05 to 0.27 L CH4 (g removedCOD)-1 in the R1 and of 0.10 to 0.12 L CH4 (g removedCOD)-1 in the R2. The average removal efficiencies were 61 to 75% for totalP, 39 to 69% for KN, 82 to 93% for orgN and 20 to 94% for Fe, Zn, Cu and Mn. The amN concentration were not reduced indicating the need to post-treatment for effluent disposal into water bodies. There were reductions of total coliforms from 99.8123 to 99.9989% and of thermotolerant coliforms from 99.9725 to 99.9999%. The conditions imposed to the UASB reactors in two stage provided high conversions of removedCOD into methane (up to 77%) and reductions of organic an inorganic pollution loads from swine wastewater.

Sarcoma sinovial de extremidades com doença localizada ao diagnóstico: tratamento e padrões de recidiva em 57 casos

OBJETIVOS: Os sarcomas sinoviais são tumores raros e agressivos que acometem adultos jovens, com sobrevida doençaespecífica em cinco anos de 57 a 63%. O presente estudo analisa a experiência institucional com este tumor, dando ênfase à associação entre variáveis clínicas, padrões de recorrência e sobrevida. MÉTODO: Entre 1970 e 2001 foram identificados 57 pacientes com sarcomas sinoviais. Fatores demográficos, clínicos e anatomopatológicos foram pesquisados. Associações entre variáveis clínicas e a sobrevida livre de recidiva local, livre de metástases e doença-específica em cinco anos foram calculadas. RESULTADOS: A idade mediana dos pacientes foi 26 anos, 56% eram masculinos, 79% eram brancos. Localizavam-se em membro inferior em 74%, proximalmente em 53%. O sintoma mais comum foi a presença de tumor em 42%. Na admissão 18% eram intactos, 42% manipulados e 40% recidivados. A maioria era maior que 5 cm., e três pacientes apresentavam metástase linfonodal. A cirurgia mais freqüente foi ressecção ampla, 30% necessitou amputação. Margens amplas foram obtidas em 65%, 51% eram tumores bifásicos. Neoadjuvância foi utilizada em 46% e adjuvância em 58% dos casos. As sobrevidas livre de recidiva local , metástases e doença específica em cinco anos foram 60±8%, 47±7% e 58±7%. A localização proximal do tumor associou-se com preservação de membro (p=-0,001), margens inadequadas (p=0,006) e subtipo bifásico (p=0,047). CONCLUSÕES: Os dados confirmam a hipótese de tratar-se de tumor agressivo, com altos índices de recidiva local e à distância. Os resultados do tratamento são comparáveis a outros centros especializados. Tratamento fora destes centros deve ser desencorajado.

Volvo PV 53-57 ja 801-802 voiteluohjeita

kuv., 18 x 12 cm

Traumatismo da medula espinhal em cães e gatos: estudo prospectivo de 57 casos

O traumatismo da medula espinhal é uma causa comum de disfunção neurológica em cães e gatos. Lesões nestas espécies ocorrem devido a vários tipos de acidentes, podendo ocasionar sequelas que prejudicam o paciente como animais de estimação ou lesões que comprometam a vida. O objetivo principal deste estudo foi a monitoração intensiva de animais com lesão medular atendidos entre 8/2009 e 11/2010 no Hospital Veterinário da Universidade Estadual de Londrina, estudando os fatores epidemiológicos e etiológicos, fatores de risco, segmentos medulares mais afetados, resultados dos tratamentos conservativo ou cirúrgico, relação entre o tempo de atendimento e a recuperação do animal, eficácia e efeitos colaterais do succinato sódico de metilprednisolona, complicações, sequelas e evolução do quadro. Durante este período foram acompanhados 57 animais (48 cães e nove gatos). Observou-se predominância de animais machos (68%) e domiciliados (79%). A principal causa de lesão foi o atropelamento (66%). O tempo entre o trauma e o atendimento foi menos de oito horas em 42% dos casos e mais de um dia em 51%. O segmento medular mais atingido foi o toracolombar (52%). Vinte animais foram submetidos à eutanásia após o atendimento inicial devido ao prognóstico reservado. O tratamento conservativo com repouso e/ou imobilização externa foi realizado em 29 animais e um bom resultado com esta modalidade foi obtida em 72,4% dos casos: houve recuperação funcional total em 17 (58,6%) animais e parcial em quatro (13,8%). Quatro animais não se recuperaram e quatro animais morreram. Oito pacientes foram submetidos ao tratamento cirúrgico, sendo que três animais recuperaram-se, um paciente não apresentou recuperação e quatro morreram ou foram submetidos a eutanásia devido a complicações no trans ou pós-operatório. O tratamento conservativo foi viável, principalmente em cães com lesão medular cervical.

Be-Fe coupled method for the analysis of 3D elastodynamic problems in the time domain

By coupling the Boundary Element Method (BEM) and the Finite Element Method (FEM) an algorithm that combines the advantages of both numerical processes is developed. The main aim of the work concerns the time domain analysis of general three-dimensional wave propagation problems in elastic media. In addition, mathematical and numerical aspects of the related BE-, FE- and BE/FE-formulations are discussed. The coupling algorithm allows investigations of elastodynamic problems with a BE- and a FE-subdomain. In order to observe the performance of the coupling algorithm two problems are solved and their results compared to other numerical solutions.

Noise and vibration damping of Fe-Cr-x alloys

The aim of the present work is to study the noise and vibration damping capacity of ferromagnetic Fe-16%Cr base alloys (before and after heat treatment) with different Al and Mo contents. The noise damping was evaluated by the level of sound emission after an impact. The vibration damping was studied using a cantilever device. In addition to these tests, the magnetic structure of the materials was also investigated by Kerr effect. It was verified that the materials can decrease noise level in the frequency range of human earring. The vibration damping is influenced by heat treatment and chemical composition of the alloy. The improvement of vibration damping after heat treatment is ascribed to the decrease of internal stresses in materials and changes in magnetic domain structures.

FE-analyysin soveltaminen S960 QC teräksisen I-profiilin äärikestävyyden määrittämisessä

Tässä työssä tutkittiin FE-analyysin soveltamista S960 QC teräksisen I-profiilin kestävyyden määrittämisessä. Työn tavoitteena oli tarkastella nykyisten suunnitteluohjeiden soveltuvuutta ultralujille teräksille ja koota ohjemateriaali I-profiilin optimoimisesta sekä FE-analyysin hyö-dyntämisestä I-profiilin staattisen ja dynaamisen kestävyyden määrittämisessä. I-profiili mitoitettiin ja optimoitiin Eurokoodi 3:ssa esitettyjen PL3 mukaisten mitoitusohjeiden avulla. Rakenteelle suoritettiin Eurokoodi 3:n ja IIW:n mukaiset lommahdus-, kiepahdus- ja vä-symiskestävyystarkastelut. Väsymistarkastelussa sovellettiin nimellisen jännityksen, rakenteelli-sen jännityksen ja tehollisen lovijännityksen menetelmiä sekä murtumismekaniikkaa. Rakenteel-lisen jännityksen menetelmässä sovellettiin lisäksi lineaarista ja parabolista pintaa pitkin ekstra-polointia, paksuuden yli linearisointia sekä Dong:in menetelmää. Lommahdus-, kiepahdus- ja väsymistarkasteluissa hyödynnettiin analyyttistä laskentaa, FE-analyysiä sekä Frank2d sovellusta. Tarkastelujen perusteella voidaan todeta, että analyyttisillä menetelmillä saadaan numeerisia me-netelmiä varmemmalla puolella olevia tuloksia. Lommahdustarkastelussa ero tulosten välillä on suurimmillaan 8 % ja kiepahdustarkastelussa suurimmillaan 20 % mutta väsymistarkastelussa saadut tulokset eroavat keskenään huomattavasti. Väsymistarkastelussa tehollisen lovijännityksen menetelmällä sekä rakenteellisen jännityksen menetelmän Dong:in menetelmällä saadaan huo-mattavasti muita menetelmiä pidempiä kestoikiä, kun taas yksinkertaisemmilla menetelmillä saa-dut kestoiät ovat lyhyempiä. Rakenteen kestävyyden määrittäminen analyyttisillä menetelmillä on melko helppoa, mutta tu-lokset ovat monesti liian konservatiivisia. FE-analyysillä saadaan puolestaan hyvin tarkkoja tu-loksia mallin ollessa yksityiskohtainen. Mallintaminen on kuitenkin aikaa ja resursseja vievää ja vaatii käyttökokemusta. FE-analyysin mahdolliset hyödyt on aina arvioitava tapauskohtaisesti tarkasteltavan geometrian, kuormitusten ja reunaehtojen perusteella.