Control en modo corriente y tensión eficaz con lazo de offset para inversor monofásico embarcado en aviones adecuado para funcionamiento en paralelo y conexión trifásica

La incorporación de un lazo de tensión eficaz de (RMS) es una posibilidad atractiva para el control de inversores de potencia de una manera sencilla. Si se combina con un control en modo corriente usando una sonda de efecto Hall, el ruido de modo común de la etapa de potencia transmitido al control puede ser reducido, mejorando la distorsión armónica total (THD) y manteniendo la posibilidad de operación en paralelo. Además, al estar el control de tensión definido sobre baja frecuencia (DC), obtener una gran ganancia a la frecuencia de interés (0Hz) es sencilla con control basado en PI, lo cual garantiza una onda de tensión de salida a 400Hz sin error, a costa de un peor desempeño ante transitorios y ante cargas no lineales. Sin embargo, la implementación de una estrategia de control de esta naturaleza puede provocar la aparición de offset en la salida. Por otra parte, el esquema oculta la información de la fase de la onda de tensión de salida, necesaria para sincronizar tres módulos monofásicos en un montaje trifásico. En este artículo el diseño e implementación del sistema completo es abordado, resolviendo los inconvenientes mencionados mediante un tercer lazo analógico de control para el offset y un algoritmo de sincronización implementado en una FPGA.

Current Mode with RMS Voltage and Offset Control Loops for a Single-Phase Aircraft Inverter Suitable for Parallel and 3-Phase Operation Modes

Rms voltage regulation may be an attractive possibility for controlling power inverters. Combined with a Hall Effect sensor for current control, it keeps its parallel operation capability while increasing its noise immunity, which may lead to a reduction of the Total Harmonic Distortion (THD). Besides, as voltage regulation is designed in DC, a simple PI regulator can provide accurate voltage tracking. Nevertheless, this approach does not lack drawbacks. Its narrow voltage bandwidth makes transients last longer and it increases the voltage THD when feeding non-linear loads, such as rectifying stages. On the other hand, the implementation can fall into offset voltage error. Furthermore, the information of the output voltage phase is hidden for the control as well, making the synchronization of a 3-phase setup not trivial. This paper explains the concept, design and implementation of the whole control scheme, in an on board inverter able to run in parallel and within a 3-phase setup. Special attention is paid to solve the problems foreseen at implementation level: a third analog loop accounts for the offset level is added and a digital algorithm guarantees 3-phase voltage synchronization.

Experiences on using closed-loop control systems for smoke control

The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. In the last years, the required quick response of the ventilation system, from normal to emergency mode, has been improved by the use of automatic and semi-automatic control systems, what reduces the response times through the support to the operators decision taking, and the use of pre-defined strategies. A further step consists on the use of closedloop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc), optimizing the quality of the smoke control process

A Visual AGV-Urban Car using Fuzzy Control

The goal of the work described in this paper is to develop a visual line guided system for being used on-board an Autonomous Guided Vehicle (AGV) commercial car, controlling the steering and using just the visual information of a line painted below the car. In order to implement the control of the vehicle, a Fuzzy Logic controller has been implemented, that has to be robust against curvature changes and velocity changes. The only input information for the controller is the visual distance from the image center captured by a camera pointing downwards to the guiding line on the road, at a commercial frequency of 30Hz. The good performance of the controller has successfully been demonstrated in a real environment at urban velocities. The presented results demonstrate the capability of the Fuzzy controller to follow a circuit in urban environments without previous information about the path or any other information from additional sensors

Design methodology in multiphase buck converter based on minimum time control for high efficiency RF amplifiers

This paper proposes an interleaved multiphase buck converter with minimum time control strategy for envelope amplifiers in high efficiency RF power amplifiers. The solution of the envelope amplifier is to combine the proposed converter with a linear regulator in series. High system efficiency can be obtained through modulating the supply voltage of the envelope amplifier with the fast output voltage variation of the converter working with several particular duty cycles that achieve total ripple cancellation. The transient model for minimum time control is explained, and the calculation of transient times that are pre-calculated and inserted into a look-up table is presented. The filter design trade-off that limits capability of envelope modulation is also discussed. The experimental results verify the fast voltage transient obtained with a 4-phase buck prototype.

Design of envelope amplifier based on interleaved multiphase buck converter with minimum time control for RF application

In this paper, an interleaved multiphase buck converter with minimum time control strategy for envelope amplifiers in high efficiency RF power amplifiers is proposed. The solution for the envelope amplifier is to combine the proposed converter with a linear regulator in series. High efficiency of envelope amplifier can be obtained through modulating the supply voltage of the linear regulator. Instead of tracking the envelope, the buck converter has discrete output voltage that corresponding to particular duty cycles which achieve total ripple cancellation. The transient model for minimum time control is explained, and the calculation of transient times that are pre-calculated and inserted into a lookup table is presented. The filter design trade-off that limits capability of envelope modulation is also discussed. The experimental results verify the fast voltage transient obtained with a 4-phase buck prototype.

Digital Control Implementation to Reduce the Cost and Improve the Performance of the Control Stage of an Industrial Switched-Mode Power Supply

The main objective of this work is the design and implementation of the digital control stage of a 280W AC/DC industrial power supply in a single low-cost microcontroller to replace the analog control stage. The switch-mode power supply (SMPS) consists of a PFC boost converter with fixed frequency operation and a variable frequency LLC series resonant DC/DC converter. Input voltage range is 85VRMS-550VRMS and the output voltage range is 24V-28V. A digital controller is especially suitable for this kind of SMPS to implement its multiple functionalities and to keep the efficiency and the performance high over the wide range of input voltages. Additional advantages of the digital control are reliability and size. The optimized design and implementation of the digital control stage it is presented. Experimental results show the stable operation of the controlled system and an estimation of the cost reduction achieved with the digital control stage.

Multiphase Buck Converter with Minimum Time Control Strategy for RF Envelope Modulation

Power amplifier supplied with constant supply voltage has very low efficiency in the transmitter. A DC-DC converter in series with a linear regulator can be used to obtain voltage modulation. Since this converter should be able to change the output voltage very fast, a multiphase buck converter with a minimum time control strategy is proposed. To modulate supply voltage of the envelope amplifier, the multiphase converter works with some particular duty cycle (i/n, i=1, 2 ... n, n is the number of phase) to generate discrete output voltages, and in these duty cycles the output current ripple can be completely cancelled. The transition times for the minimum time are pre-calculated and inserted in a look-up table. The theoretical background, the system model that is necessary in order to calculate the transition times and the experimental results obtained with a 4-phase buck prototype are given

Single-Stage Grid-Connected Forward Microinverter with Boundary Mode Control

This paper presents a microinverter to be integrated into a solar module. The proposed solution combines a forward converter and a constant off-time boundary mode control, providing MPPT capability and unity power factor in a single-stage converter. The transformer structure of the power stage remains as in the classical DC-DC forward converter. Transformer primary windings are utilized for power transfer or demagnetization depending on the grid semi-cycle. Furthermore, bidirectional switches are used on the secondary side allowing direct connection of the inverter to the grid. Design considerations for the proposed solution are provided, regarding the inductance value, transformer turns ratio and frequency variation during a line semi-cycle. The decoupling of the twice the line frequency power pulsation is also discussed, as well as the maximum power point tracking (MPPT) capability. Simulation and experimental results for a 100W prototype are enclosed

Teaching digital control of switch mode power supplier

This paper explains the methodology followed to teach the subject `Digital control of power converters'. This subject belongs to the research master on `Industrial Electronics' of the Universidad Politécnica de Madrid. The subject is composed of several theoretical lessons plus the development of an actual digital control. For that purpose an ad hoc dc-dc converter has been designed and built. The use of this board together with some software tools seems a very powerful way for the students to learn the concepts from the design to the real world

On-board and Ground Visual Pose Estimation Techniques for UAV Control

In this paper, two techniques to control UAVs (Unmanned Aerial Vehicles), based on visual information are presented. The first one is based on the detection and tracking of planar structures from an on-board camera, while the second one is based on the detection and 3D reconstruction of the position of the UAV based on an external camera system. Both strategies are tested with a VTOL (Vertical take-off and landing) UAV, and results show good behavior of the visual systems (precision in the estimation and frame rate) when estimating the helicopter¿s position and using the extracted information to control the UAV.

Músculos Inteligentes en Robots Biológicamente Inspirados: Modelado, Control y Actuación

Las aleaciones metálicas que exhiben una propiedad conocida como efecto de memoria de forma, pertenecen a la clase de materiales inteligentes cuya aplicación más notable en el campo de la robótica se refleja en el uso de actuadores musculares artificiales, ó músculos inteligentes. Estos materiales tienen una estructura cristalina uniforme que cambia radicalmente en función de su temperatura de transición, causando su deformación. Se les denomina materiales inteligentes por la capacidad de recordar su configuración inicial después de recibir dicho estímulo térmico. Este artículo presenta la implementación de un actuador muscular inteligente aplicado en un micro-robot aéreo bio-inspirado tipo murciélago. Esto mamíferos voladores desarrollaron poderosos músculos que se extienden a lo largo de la estructura ósea de las alas, adquiriendo una asombrosa capacidad de maniobra gracias a la capacidad de cambiar la forma del ala durante el vuelo. Replicar este tipo de alas mórficas en un prototipo robótico requiere el análisis de nuevas tecnologías de actuación, abordando los problemas de modelado y control que garanticen la aplicabilidad de este actuador compuesto por fibras musculares de SMAs

Desarrollo, análisis y caracterización de procesos de soldeo térmico de espumas de aluminio

Uno de los retos actuales aún pendiente de lograr trabajando con espumas de aluminio, es el desarrollo de métodos de unión fácilmente reproducibles a nivel industrial que permitan la unión de espumas de aluminio entre sí o con otros componentes tipo pletinas, para así poder fabricar piezas de mayor tamaño o con formas complejas, a la vez que se conserven las propiedades y características principales de las espumas de aluminio, tanto en la zona principal de unión o cordón, como en la interfase y zona afectada térmicamente, que se encuentran anexa. Los actuales procesos de unión más utilizados con espumas de aluminio, se basan principalmente en adhesivos y uniones mecánicas. Estas soluciones a priori válidas, añaden problemas técnicos a determinadas aplicaciones de las espumas que frenan la completa integración de estos materiales en un entorno de fabricación flexible y global. Por esta razón, los actuales procesos de producción de las espumas de aluminio se restringen a determinadas ofertas hechas a la medida del cliente, no pudiendo atender por falta de soluciones, a una gran parte del potencial mercado de estos materiales. En el presente trabajo de investigación se han desarrollado y caracterizado diferentes métodos de unión de espumas de aluminio, en configuración a tope y de espumas de aluminio con pletinas en configuración a solape, basados en procesos por soldeo térmico. One of the current challenges even pending of being achieved working with aluminium foams, is the development of easily reproducible methods at industrial level that allow the joint of aluminium foams between them or with other elements as for example aluminium plates for making bigger pieces or with more complex forms, remaining simultaneously in the weld bead the properties and main characteristics of aluminium foam, so much in the joint area or interface, since in the affected closer thermal zone. Currently, the most used joint processes for applying to aluminium foams are based mainly on adhesives and mechanical joins. These solutions initially valid, add technical problems to certain aluminium foams applications, which stop the complete integration of these materials in a more flexible and global manufacture environment. For this reason, current aluminium foam manufacturing processes are restricted to certain offers done to a specific customer requirement, not being able to attend for lack of available solutions, to a great potential market of these materials. In the present work, different joint methods between aluminium foams and between aluminium foams and plates for butt and lap configurations have been developed and characterized based on thermal welding processes.

Análisis de los procesos de innovación en las organizaciones de servicio: sectores comercio, salud y educación

La creciente importancia del sector servicios en la economía se refleja en términos del empleo, la participación en el producto interno bruto y el impacto en la calidad de vida de los habitantes. De la misma forma crece el interés por entender los procesos de innovación en las organizaciones de servicio. En este sentido, el objeto de este trabajo doctoral es desarrollar un modelo de análisis de los procesos de innovación en las organizaciones de servicio y verificar su aplicabilidad en los sectores comercio, educación y salud en Venezuela. Basado en las premisas de innovación propuesta para el ámbito de la red de valor centrada en el servicio, el modelo propuesto agrega las fases “liderar” y “co-operar” al modelo de innovación TEMAGUIDE (COTEC, 1999). El modelo ampliado de siete fases plantea un índice general y cinco índices específicos para medir el desarrollo de los procesos de innovación general, interna, externa, de actividades, de frecuencia según el tipo de innovación, y de uso de sistemas, técnicas y herramientas. Basado en el modelo se define una nueva trayectoria de innovación denominada “orientada a la red de valor centrada en el servicio” y un modo de innovación definido como cooperación general. La investigación es de tipo descriptivo con diseño no experimental transversal, basado en una extensa revisión teórica. El trabajo de campo se realizó a través de una encuesta que obtuvo respuesta de treinta (30) organizaciones. Los resultados de la prueba beta muestran la aplicabilidad, funcionalidad, uso y utilidad del instrumento utilizado. Los resultados sectoriales muestran un nivel de desarrollo de los procesos de innovación medio-bajo para el sector comercio, seguido por los sectores salud y educación. Las fases del proceso de innovación más desarrolladas son “co-operar” y “liderar”, mientras las menos desarrolladas son “focalizar” e “implantar”. Cuando se analizan los índices de innovación, se observa la relación entre el uso de sistemas, técnicas y herramientas, y el grado de desarrollo del proceso de innovación. Igualmente se observa que en la medida que los procesos internos de innovación son más desarrollados, mayor es la actividad de innovación externa, en cooperación con clientes, suplidores, y en menor medida con universidades y centros de investigación. La aplicación del modelo en conjunto con la técnica de análisis de conglomerado permitió determinar el grupo de organizaciones líderes y definir sus prácticas de innovación. Este grupo arrojó un nivel medio-alto de desarrollo, destacándose en la fase de “co-operar”, presenta una trayectoria de innovación denominada “orientada a la red de valor centrada en el servicio” y un modo de cooperación general. El modelo presentado permite a los gerentes definir áreas de mejora de su proceso de innovación y establecer un adecuado balance en el desarrollo de las actividades internas y externas, así como en el uso adecuado de herramientas y técnicas de innovación.

Advanced predictive quality control strategy involving different facilities

There are many industries that use highly technological solutions to improve quality in all of their products. The steel industry is one example. Several automatic surface-inspection systems are used in the steel industry to identify various types of defects and to help operators decide whether to accept, reroute, or downgrade the material, subject to the assessment process. This paper focuses on promoting a strategy that considers all defects in an integrated fashion. It does this by managing the uncertainty about the exact position of a defect due to different process conditions by means of Gaussian additive influence functions. The relevance of the approach is in making possible consistency and reliability between surface inspection systems. The results obtained are an increase in confidence in the automatic inspection system and an ability to introduce improved prediction and advanced routing models. The prediction is provided to technical operators to help them in their decision-making process. It shows the increase in improvement gained by reducing the 40 % of coils that are downgraded at the hot strip mill because of specific defects. In addition, this technology facilitates an increase of 50 % in the accuracy of the estimate of defect survival after the cleaning facility in comparison to the former approach. The proposed technology is implemented by means of software-based, multi-agent solutions. It makes possible the independent treatment of information, presentation, quality analysis, and other relevant functions.