Hydrodynamic Simulations Of Vacuum-Driven Storage Tanks

As a result of urbanization, stormwater runoff flow rates and volumes are significantly increased due to increasing impervious land cover and the decreased availability of depression storage. Storage tanks are the basic devices to efficiently control the flow rate in drainage systems during wet weather. Presented in the paper conception of vacuum-driven detention tanks allows to increase the storage capacity by usage of space above the free surface water elevation at the inlet channel. Partial vacuum storage makes possible to gain cost savings by reduction of both the horizontal area of the detention tank and necessary depth of foundations. Simulation model of vacuum-driven storage tank has been developed to estimate potential profits of its application in urban drainage system. Although SWMM5 has no direct options for vacuum tanks an existing functions (i.e. control rules) have been used to reflect its operation phases. Rainfall data used in simulations were recorded at raingage in Czestochowa during years 2010÷2012 with time interval of 10minutes. Simulation results gives overview to practical operation and maintenance cost (energy demand) of vacuum driven storage tanks depending of the ratio: vacuum-driven volume to total storage capacity. The following conclusion can be drawn from this investigations: vacuum-driven storage tanks are characterized by uncomplicated construction and control systems, thus can be applied in newly developed as well as in the existing urban drainage systems. the application of vacuum in underground detention facilities makes possible to increase of the storage capacity of existing reservoirs by usage the space above the maximum depth. Possible increase of storage capacity can achieve even a few dozen percent at relatively low investment costs. vacuum driven storage tanks can be included in existing simulation software (i.e. SWMM) using options intended for pumping stations (including control and action rules ).

JCML: A specification language for the runtime verification of Java Card programs

COSTA, Umberto Souza; MOREIRA, Anamaria Martins; MUSICANTE, Matin A.; SOUZA NETO, Plácido A. JCML: A specification language for the runtime verification of Java Card programs. Science of Computer Programming. [S.l]: [s.n], 2010.

Specification and Runtime Verification of Java Card Programs

COSTA, Umberto Souza da; MOREIRA, Anamaria Martins; MUSICANTE, Martin A. Specification and Runtime Verification of Java Card Programs. Electronic Notes in Theoretical Computer Science. [S.l:s.n], 2009.

Um sistema para gestão do conhecimento em ameaças, vulnerabilidades e seus efeitos

Attacks to devices connected to networks are one of the main problems related to the confidentiality of sensitive data and the correct functioning of computer systems. In spite of the availability of tools and procedures that harden or prevent the occurrence of security incidents, network devices are successfully attacked using strategies applied in previous events. The lack of knowledge about scenarios in which these attacks occurred effectively contributes to the success of new attacks. The development of a tool that makes this kind of information available is, therefore, of great relevance. This work presents a support system to the management of corporate security for the storage, retrieval and help in constructing attack scenarios and related information. If an incident occurs in a corporation, an expert must access the system to store the specific attack scenario. This scenario, made available through controlled access, must be analyzed so that effective decisions or actions can be taken for similar cases. Besides the strategy used by the attacker, attack scenarios also exacerbate vulnerabilities in devices. The access to this kind of information contributes to an increased security level of a corporation's network devices and a decreased response time to occurring incidents

Fast dynamics in the optical storage with Langmuir-Blodgett films of a diazocrown ether molecule

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Design and Analysis of Optical Interconnection Networks for a Dataflow Parallel Computer

This work shows the design, simulation, and analysis of two optical interconnection networks for a Dataflow parallel computer architecture. To verify the optical interconnection network performance on the Dataflow architecture, we have analyzed the load balancing among the processors during the parallel programs executions. The load balancing is a very important parameter because it is directly associated to the dataflow parallelism degree. This article proves that optical interconnection networks designed with simple optical devices can provide efficiently the dataflow requirements of a high performance communication system.

Arquitetura com elevada taxa de processamento e reduzida largura de banda de memória para a estimação de movimento em vídeos digitais

Nowadays several electronics devices support digital videos. Some examples of these devices are cellphones, digital cameras, video cameras and digital televisions. However, raw videos present a huge amount of data, millions of bits, for their representation as the way they were captured. To store them in its primary form it would be necessary a huge amount of disk space and a huge bandwidth to allow the transmission of these data. The video compression becomes essential to make possible information storage and transmission. Motion Estimation is a technique used in the video coder that explores the temporal redundancy present in video sequences to reduce the amount of data necessary to represent the information. This work presents a hardware architecture of a motion estimation module for high resolution videos according to H.264/AVC standard. The H.264/AVC is the most advanced video coder standard, with several new features which allow it to achieve high compression rates. The architecture presented in this work was developed to provide a high data reuse. The data reuse schema adopted reduces the bandwidth required to execute motion estimation. The motion estimation is the task responsible for the largest share of the gains obtained with the H.264/AVC standard so this module is essential for final video coder performance. This work is included in Rede H.264 project which aims to develop Brazilian technology for Brazilian System of Digital Television

BMMobile: uma linha de produtos para dimensionamento de bombeio mecânico em dispositivos móveis

With the increase of processing ability, storage and several kinds of communication existing such as Bluetooth, infrared, wireless networks, etc.., mobile devices are no longer only devices with specific function and have become tools with various functionalities. In the business field, the benefits that these kinds of devices can offer are considerable, because the portability allows tasks that previously could only be performed within the work environment, can be performed anywhere. In the context of oil exploration companies, mobile applications allow quick actions could be taken by petroleum engineers and technicians, using their mobile devices to avoid potential catastrophes like an unexpected stop or break of important equipment. In general, the configuration of equipment for oil extraction is performed on the work environment using computer systems in desktop platforms. After the obtained configuration, an employee goes to equipment to be configured and perform the modifications obtained on the use desktop system. This management process equipment for oil extraction takes long time and does not guarantee the maintenance in time to avoid problems. With the use of mobile devices, management and maintenance of equipment for oil extraction can be performed in a more agile time once it enables the engineer or technician oil can perform this configuration at the time and place where the request comes for example, near in the oil well where the equipment is located. The wide variety of mobile devices creates a big difficulty in developing mobile applications, since for one application can function in several types of devices, the application must be changed for each specific type of device, which makes the development quite costly. This paper defines and implements a software product line for designing sucker-rod pumping systems on mobile devices. This product line of software, called BMMobile, aims to produce products that are capable of performing calculations to determine the possible configurations for the equipment in the design suckerrod pumping, and managing the variabilities of the various products that can be generated. Besides, this work performs two evaluations. The first evaluation will verify the consistency of the products produced by the software product line. The second evaluation will verify the reuse of some products generated by SPL developed

Dielectric and fatigue properties of Pb(Zr0.53Ti0.47)O-3 thin films prepared from oxide precursors method

Fatigue is an important problem to be considered if a ferroelectric film is used for non-volatile memory devices. In this phenomena, the remanent polarization and coercive field properties degrades in cycles which increase in hysteresis loops. The reasons have been attributed to different mechanisms such as a large voltage applied on ferroelectric film in every reading process in Ferroelectric Random Access Memory (FeRAM) or memories for digital storage in computer, grain size effects and others. The aim of this work is to investigate the influence of the crystallization kinetics on dielectric and ferroelectric properties of the Pb(Zr0.53Ti0.47)O-3 thin films prepared by an alternative chemical method. Films were crystallized in air on Pt/Ti/SiO2/Si substrates at 700 degrees C for 1 hour, in conventional thermal annealing (CTA), and at 700 degrees C for 1 min and 700 degrees C 5 min, using a rapid thermal annealing (RTA) process. Final films were crack free and presented an average of 750 nm in thickness. Dielectric properties were studied in the frequency range of 100 Hz - 1 MHz. All films showed a dielectric dispersion at low frequency. Ferroelectric properties were measured from hysteresis loops at 10 kHz. The obtained remanent polarization (P-r) and coercive field (E-c) were 3.7 mu C/cm(2) and 71.9 kV/cm respectively for film crystallized by CTA while in films crystallized by RTA these parameters were essentially the same. In the fatigue process, the P, value decreased to 14% from the initial value after 1.3 x 10(9) switching cycles, for film by CTA, while for film crystallized by RTA for 5 min, P, decreased to 47% from initial value after 1.7 x 10(9) switching cycles.

An attack signature model to computer security intrusion detection

Internal and external computer network attacks or security threats occur according to standards and follow a set of subsequent steps, allowing to establish profiles or patterns. This well-known behavior is the basis of signature analysis intrusion detection systems. This work presents a new attack signature model to be applied on network-based intrusion detection systems engines. The AISF (ACME! Intrusion Signature Format) model is built upon XML technology and works on intrusion signatures handling and analysis, from storage to manipulation. Using this new model, the process of storing and analyzing information about intrusion signatures for further use by an IDS become a less difficult and standardized process.

An active leakage-injection scheme applied to low-voltage SRAMs

An active leakage-injection scheme (ALIS) for low-voltage (LV) high-density (HD) SRAMs is presented. By means of a feedback loop comprising a servo-amplifier and a common-drain MOSFET, a current matching the respective bit-line leakage is injected onto the line during precharge and sensing, preventing the respective capacitances from erroneous discharges. The technique is able to handle leakages up to hundreds of μA at high operating temperatures. Since no additional timing is required, read-out operations are performed at no speed penalty. A simplified 256×1bit array was designed in accordance with a 0.35 CMOS process and 1.2V-supply. A range of PSPICE simulation attests the efficacy of ALIS. With an extra power consumption of 242 μW, a 200 μA-leakage @125°C, corresponding to 13.6 times the cell current, is compensated.

JSEG-based image segmentation in computer vision for agricultural mobile robot navigation

This project aims to apply image processing techniques in computer vision featuring an omnidirectional vision system to agricultural mobile robots (AMR) used for trajectory navigation problems, as well as localization matters. To carry through this task, computational methods based on the JSEG algorithm were used to provide the classification and the characterization of such problems, together with Artificial Neural Networks (ANN) for pattern recognition. Therefore, it was possible to run simulations and carry out analyses of the performance of JSEG image segmentation technique through Matlab/Octave platforms, along with the application of customized Back-propagation algorithm and statistical methods in a Simulink environment. Having the aforementioned procedures been done, it was practicable to classify and also characterize the HSV space color segments, not to mention allow the recognition of patterns in which reasonably accurate results were obtained.

Electrical Power Distribution System modeling with VHDL-AMS for the construction of a Real-Time Digital Simulator using FPGAS devices

This paper presents a distribution feeder simulation using VHDL-AMS, considering the standard IEEE 13 node test feeder admitted as an example. In an electronic spreadsheet all calculations are performed in order to develop the modeling in VHDL-AMS. The simulation results are compared in relation to the results from the well knowing MatLab/Simulink environment, in order to verify the feasibility of the VHDL-AMS modeling for a standard electrical distribution feeder, using the software SystemVision™. This paper aims to present the first major developments for a future Real-Time Digital Simulator applied to Electrical Power Distribution Systems. © 2012 IEEE.

Temperature and storage period over spermatic parameters of jundia, Rhamdia quelen (Quoy & Gaimard, 1824)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Sistema informatizado para dispositivos móveis de coleta dos dados referentes à cesta básica do município de Botucatu/SP

The collection of prices for basic goods supply is very important for the population, based on the collection and processing of these data the CLI (Cost Living Index) is calculated among others, helping consumers to shop more rationally and with a clearer view of each product impact of each product on their household budget, not only food, but also cleaning products and personal hygiene ones. Nowadays, the project of collection of prices for basic goods supply is conducted weekly in Botucatu - SP through a spreadsheet. The aim of this work was to develop a software which utilized mobile devices in the data collection and storage phase, concerning the basic goods supply in Botucatu -SP. This was created in order to eliminate the need of taking notes in paper spreadsheets, increasing efficiency and accelerating the data processing. This work utilized the world of mobile technology and development tools, through the platform".NET" - Compact Framework and programming language Visual Basic".NET" was used in the handheld phase, enabling to develop a system using techniques of object oriented programming, with higher speed and reliability in the codes writing. A HP Pavilion dv3 personal computer and an Eten glofish x500+ handheld computer were used. At the end of the software development, collection, data storing and processing in a report, the phase of in loco paper spreadsheets were eliminated and it was possible to verify that the whole process was faster, more consistent, safer, more efficient and the data were more available.