A method to determine volatile contaminants in polyethylene terephthalate (PET) packages by HDC-GC-FID and its application to post-consumer materials

A simple and low cost method to determine volatile contaminants in post-consumer recycled PET flakes was developed and validated by Headspace Dynamic Concentration and Gas Chromatography-Flame Ionization Detection (HDC-GC-FID). The analytical parameters evaluated by using surrogates include: correlation coefficient, detection limit, quantification limit, accuracy, intra-assay precision, and inter-assay precision. In order to compare the efficiency of the proposed method to recognized automated techniques, post-consumer PET packaging samples collected in Brazil were used. GC-MS was used to confirm the identity of the substances identified in the PET packaging. Some of the identified contaminants were estimated in the post-consumer material at concentrations higher than 220 ng.g-1. The findings in this work corroborate data available in the scientific literature pointing out the suitability of the proposed analytical method.

Propiedades termofísicas del jugo concentrado de lulo a temperaturas por encima del punto de congelación

En este trabajo fueron determinados experimentalmente el calor específico, conductividad térmica, difusividad térmica y densidad del jugo de lulo en el rango de contenido de agua de 0.55 a 0.90 (p/p en base húmeda) y en temperaturas variando de 4 a 78.6 °C. La conductividad térmica y el calor específico fueron obtenidos utilizando el mismo aparato - una célula constituida de dos cilindros concéntricos - operando en estado estacionario y no- estacionario, respectivamente. La difusividad térmica fue obtenida a través del método de Dickerson y la densidad determinada por picnometria. Tanto la temperatura como el contenido de agua presentaron una fuerte influencia en los datos experimentales de las propiedades termofísicas del jugo de lulo. Los resultados obtenidos fueron utilizados para obtener modelos matemáticos y predecir estas propiedades en función de la concentración y la temperatura.

Propiedades termodinámicas de sorción de agua de la pulpa de lulo en polvo con encapsulantes

Datos de humedad de equilibrio de polvo de pulpa de lulo (PL) con y sin aditivos - 58% de maltodextrina (MD) o 58% de goma Arábiga (GA) - fueran determinados en las temperaturas de 20, 30, 40 y 50 °C utilizando el método estático gravimétrico para un rango de actividades de agua entre 0.06 y 0.90. Las isotermas presentaran formato sigmoidal del tipo III, y el modelo de Guggenhein-Anderson-de Boer (GAB) fue ajustado satisfactoriamente a los datos experimentales de humedad de equilibrio en función de la actividad de agua. La adición de encapsulantes afecto las isotermas de tal manera que en la misma actividad de agua, las muestras PL + GA y PL + MD presentaron un menor contenido de humedad de equilibrio y no fueron afectadas por la variación de temperatura. Los calores isostéricos de sorción de las pulpas en polvo con encapsulantes fueron mayores (menos negativos) con relación a las pulpas de lulo en polvo, sugiriendo la existencia de sitios polares más activos en el producto sin adición de GA o MD. Una relación exponencial empírica fue utilizada para describir la dependencia del calor de sorción con el contenido de humedad del material.

Influência do grau de hidrólise do poli(vinil álcool) nas propriedades físicas de filmes à base de blendas de gelatina e poli(vinil álcool) plastificados com glicerol

O objetivo deste trabalho foi o estudo do efeito do Grau de Hidrólise (GH) do poli(vinil álcool) (PVA) nas propriedades dos filmes à base de blendas de gelatina suína e PVA com dois GH. Os filmes foram produzidos com soluções com 2 g de macromoléculas/100 g de solução, contendo 23,1 g de PVA.100 g-1 de macromoléculas e 25 g de glicerol/100 g de macromoléculas. As propriedades mecânicas e térmicas, cor, opacidade, umidade e solubilidade, além de espectros de infravermelho com transformada de Fourier (FTIR) dos filmes, foram estudadas. As soluções foram analisadas por reometria dinâmica. Os filmes produzidos com o PVA de menor GH foram mais higroscópicos e mais solúveis. Mas o tipo de PVA não afetou a cor, afetando a opacidade e o brilho dos filmes. O PVA com maior GH proporcionou filmes mais resistentes, e o PVA de menor GH produziu filmes mais resistentes à tração, embora menos deformáveis na perfuração. O GH do PVA não afetou a temperatura de transição vítrea dos filmes, determinada na primeira varredura, mas a afetou na segunda varredura. Os resultados das análises de FTIR corroborraram com esses resultados. As propriedades viscoelásticas das soluções não foram afetadas pelo GH do PVA, muito possivelmente por se tratar de soluções diluídas.

Efeito da lavagem e da adição de aditivos sobre a estabilidade de carne mecanicamente separada de tilápia do Nilo (Oreochromis niloticus) durante estocagem a -18 ºC

Este estudo teve como objetivo avaliar a influência da lavagem e da adição de eritorbato de sódio e tripolifosfato de sódio na estabilidade de Carne Mecanicamente Separada (CMS) de tilápia de Nilo (Oreochromis niloticus) durante 6 meses de armazenamento a -18 ºC. A CMS obtida por meio de máquina separadora de carne e ossos foi dividida em quatro tratamentos (CMS lavada com e sem aditivos, e CMS não lavada com e sem aditivos) e mantida sob congelamento a -18 ºC, por 180 dias. A estabilidade foi avaliada por meio de análises microbiológicas e determinações de nitrogênio não proteico (NNP), bases nitrogenadas voláteis (BNV), substâncias reativas ao ácido tiobarbitúrico (TBARS), pH e drip (perda de água no descongelamento). O processo de lavagem causou redução de aproximadamente 41, 44 e 66% nos teores de proteína bruta, lipídios e cinzas, respectivamente, reduzindo também os valores iniciais de NNP, BNV e TBARS. Durante o armazenamento, foram observados aumentos (p < 0,05) nos teores de NNP, BNV e pH em praticamente todos os tratamentos, exceto na CMS lavada com aditivos, que não apresentou aumentos significativos nos teores de NNP e pH. O uso de aditivos nas CMS diminuiu o drip ao longo do armazenamento, mas não alterou (p > 0,05) os teores de TBARS. Os parâmetros microbiológicos avaliados não ultrapassaram os limites permitidos pela legislação. As CMS permaneceram estáveis e em boas condições de utilização, independentemente da inclusão de aditivo, sendo viável sua estocagem a -18 ºC por 180 dias.

Produção de biotensoativos a partir de resíduos de óleos e gorduras

O presente trabalho visou a seleção de microrganismos com capacidade de produzir biotensoativos a partir de resíduos de óleos e gorduras gerados em restaurantes e indústrias alimentícias. Borra de soja, gordura de frango, gordura vegetal hidrogenada e óleo de soja usado em frituras foram estudados como fonte de carbono. Os isolados LMI 6c e LMI 7a, ambos pertencentes ao gênero Pseudomonas, foram selecionados como potenciais produtores de biotensoativos. Dentre os resíduos propostos, a borra de soja foi considerada o melhor substrato, gerando 9,69 g.L-1 de ramnolipídios e uma tensão superficial de 31 mN/m.

Aplicação experimental de um modelo de conduta de inspeção sanitária no comércio varejista de alimentos

Este trabalho teve por objetivo aplicar um procedimento para diagnóstico e modelo de inspeção higiênico-sanitária em estabelecimentos varejistas de alimentos, no Município de Ibiúna, Estado de São Paulo, Brasil, e analisar os resultados com vistas a atingir os objetivos da vigilância sanitária. O trabalho foi desenvolvido durante seis meses em 19 estabelecimentos varejistas de alimentos classificados como padarias, restaurantes e açougues, sendo que na primeira inspeção realizou-se o diagnóstico da situação, com a identificação das não conformidades e avaliação das condições higiênico-sanitárias dos estabelecimentos e foi obtida a pontuação média de 64. Após esta etapa iniciaram-se retornos programados aos estabelecimentos pela equipe da vigilância sanitária a fim de verificar a evolução das adequações sanitárias. No diagnóstico e em todos os retornos programados foi aplicado roteiro de inspeção e produção de relatórios detalhados destinados aos proprietários. Todos os manipuladores de alimentos dos estabelecimentos inspecionados foram capacitados em relação a conceitos básicos de higiene em alimentos. Os resultados mostraram que, após três retornos de inspeções em cada estabelecimento, 100% apresentaram-se como satisfatórios, com pontuação média de 90. O modelo de inspeção sanitária aplicado mostrou-se viável para a promoção da segurança alimentar.

Quasinormal modes of black holes in anti-de Sitter space: A numerical study of the eikonal limit

Using series solutions and time-domain evolutions, we probe the eikonal limit of the gravitational and scalar-field quasinormal modes of large black holes and black branes in anti-de Sitter backgrounds. These results are particularly relevant for the AdS/CFT correspondence, since the eikonal regime is characterized by the existence of long-lived modes which (presumably) dominate the decay time scale of the perturbations. We confirm all the main qualitative features of these slowly damped modes as predicted by Festuccia and Liu [G. Festuccia and H. Liu, arXiv:0811.1033.] for the scalar-field (tensor-type gravitational) fluctuations. However, quantitatively we find dimensional-dependent correction factors. We also investigate the dependence of the quasinormal mode frequencies on the horizon radius of the black hole (brane) and the angular momentum (wave number) of vector- and scalar-type gravitational perturbations.

EVALUATING VIBRATIONS ON A SMALL-SCALE MODEL OF A TIMBER FOOTBRIDGE

In Brazil, the study of pedestrian-induced vibration on footbridges has been undertaken since the early 1990s, for concrete and steel footbridges. However, there are no recorded studies of this kind for timber footbridges. Brazilian code ABNT NBR 7190 (1997) gives design requirements only for static loads in the case of timber footbridges, without considering the serviceability limit state from pedestrian-induced vibrations. The aim of this work is to perform a theoretical dynamic, numerical and experimental analysis on simply-supported timber footbridges, by using a small-scale model developed from a 24 m span and 2 m width timber footbridge, with two main timber beams. Span and width were scaled down (1:4) to 6 m e 0.5 in, respectively. Among the conclusions reached herein, it is emphasized that the Euler-Bernoulli beam theory is suitable for calculating the vertical and lateral first natural frequencies in simply-supported timber footbridges; however, special attention should be given to the evaluation of lateral bending stiffness, as it leads to conservative values.

Influence of metallic nanoparticles on electric-dipole and magnetic-dipole transitions of Eu(3+) doped germanate glasses

Luminescence properties of Eu(3+) doped germanate glasses containing either silver or gold nanoparticles (NPs) were investigated for excitation at 405 nm. Enhanced emissions and luminescence quenching of the Eu(3+) transitions in the range from 570 to 720 nm were observed for samples having various concentrations of metallic NPs. Electric-dipole and magnetic-dipole transitions that originate from the Eu(3+) level (5)D(0) exhibit large enhancement due to the presence of the metallic NPs. The results suggest that the magnetic response of rare-earth doped metal-dielectric composites at optical frequencies can be as strong as their electric response due to the confinement of the optical magnetic field. (C) 2010 American Institute of Physics. [doi:10.1063/1.3431347]

Enhanced luminescence of Tb(3+)/Eu(3+) doped tellurium oxide glass containing silver nanostructures

We report on energy transfer studies in terbium (Tb(3+))-europium (Eu(3+)) doped TeO(2)-ZnO-Na(2)O-PbO glass containing silver nanostructures. The samples excitation was made using ultraviolet radiation at 355 nm. Luminescence spectra were recorded from approximate to 480 to approximate to 700 nm. Enhanced Eu(3+) luminescence at approximate to 590 nm (transition (5)D(0)-(7)F(1)) and approximate to 614 nm (transition (5)D(0)-(7)F(2)) are observed. The large luminescence enhancement was obtained due to the simultaneous contribution of the Tb(3+)-Eu(3+) energy transfer and the contribution of the intensified local field on the Eu(3+) ions located near silver nanostructures.

Photoluminescence enhancement by gold nanoparticles in Eu(3+) doped GeO(2)-Bi(2)O(3) glasses

We report large photoluminescence (PL) enhancement in Eu(3+)-doped GeO(2)-Bi(2)O(3) glasses containing gold nanoparticles (NPs). Growth of approximate to 1000% in the PL intensity corresponding to the Eu(3+) transition (5)D(0)->(7)F(2), at 614 nm, was observed in comparison with a reference sample that does not contain gold NPs. Other PL bands from 580 to 700 nm are also enhanced. The enhancement of the PL intensity is attributed to the increased local field in the Eu(3+) locations due to the presence of the NPs and the energy transfer from the excited NPs to the Eu(3+) ions.

LOCAL HEAD LOSS OF NON-COAXIAL EMITTERS INSERTED IN POLYETHYLENE PIPE

The design of a lateral line for drip irrigation requires accurate evaluation of head losses in not only the pipe but in the emitters as well. A procedure was developed to determine localized head losses within the emitters by the formulation of a mathematical model that accounts for the obstruction caused by the insertion point. These localized losses can be significant when compared with tire total head losses within the system due to the large number of emitters typically installed along the lateral line. Air experiment was carried out by altering flow characteristics to create Reynolds numbers (R) from 7,480 to 32,597 to provide turbulent flow and a maximum velocity of 2.0 m s(-1). The geometry of the emitter was determined by an optical projector and sensor An equation was formulated to facilitate the localized head loss calculation using the geometric characteristics of the emitter (emitter length, obstruction ratio, and contraction coefficient). The mathematical model was tested using laboratory measurements on four emitters. The local head loss was accurately estimated for the Uniram (difference of +13.6%) and Drip Net (difference of +7.7%) emitters, while appreciable deviations were found for the Twin Plus (-21.8%) and Tiran (+50%) emitters. The head loss estimated by the model was sensitive to the variations in the obstruction area of the emitter However, the variations in the local head loss did not result in significant variations in the maximum length of the lateral lines. In general, for all the analyzed emitters, a 50% increase in the local head loss for the emitters resulted in less than an 8% reduction in the maximum lateral length.

Long Terminal Repeat Sequence Analysis of HTLV-2 Molecular Variants Identified in Southern Brazil

In Brazil, human T-lymphotropic virus type 2 (HTLV-2) is endemic in Amerindians and epidemic in intravenous drug users (IDUs). The long terminal repeat (LTR) is the most divergent genomic region of HTLV-2, therefore useful to characterize subtypes. Nucleotide sequence and restriction fragment length polymorphism (RFLP) analysis of LTR genomic segments of fourteen HTLV-2 strains isolated from HIV-infected patients of Londrina, Southern Brazil, were carried out. Molecular analysis disclosed that all HTLV-2 strains belonged to 2a subtype, and RFLP detected the presence of the a4, a5, and a6 subgroups according to Switzer's nomenclature. RFLP correlated with nucleotide sequence, and phylogenetic analysis clustered HTLV-2 sequences of IDUs into subgroups a5 and a6. HTLV-2 sequences from individuals of sexual risk factor clustered into the a4 subgroup. These results extend the knowledge of the genetic diversity of HTLV-2 circulating in Brazil and provide insights into HTLV-2 transmission and virus movement in this geographic area.

Prevalence of Human T-Cell Lymphotropic Virus (HTLV-1/2) in Individuals from Public Health Centers in Mozambique

The prevalence of human T-cell lymphotropic viruses types 1 and 2 (HTLV-1/2) in Mozambique is not known. The present study examined blood samples from 208, 226, and 318 individuals from Northern, Central, and Southern Mozambique, respectively, of all socioeconomic and demographic strata attending public health centers in Mozambique for HTLV-1/2-specific antibodies. Serum samples were assessed for HIV- and HTLV-1/2-specific antibodies by using enzyme immunoassays, and infections with HTLV-1 and -2 were confirmed by using Western blot. An overall HTLV-1/2 prevalence of 2.3% (2.9% in female and 1.1% in male subjects) was observed, and the prevalence of infection increased with age. Regional variation in the prevalence of HIV and HTLV-1/2 was observed; 32.2%, 65.5%, and 44% of individuals tested HIV positive in Northern, Central, and Southern Mozambique, respectively, and 2.4%, 3.9%, and 0.9% tested HTLV-1/2 positive in the same regions. HTLV-1 infection was confirmed in these individuals. No association between HTLV-1 infection and socio-demographic variables or HIV status was detected, although the low number of HTLV-1-positive cases did not allow robust statistical analyses. The results obtained suggest different risk factors and epidemiologic correlates of HIV and HTLV-1 transmission in Mozambique. Furthermore, our results suggested that North and Central Mozambique should be considered endemic regions for HTLV-1 infection. As no cases of HTLV-2 were detected, HTLV-2 appears to have not been introduced into Mozambique.