Simultaneous flow injection preconcentration of lead and cadmium using cloud point extraction and determination by atomic absorption spectrometry

A flow injection (FI) micelle-mediated separation/preconcentration procedure for the determination of lead and cadmium by flame atomic absorption spectrometry (FAAS) has been proposed. The analytes reacted with 1-(2-thiazolylazo)-2-naphthol (TAN) to form hydrophobic chelates, which were extracted into the micelles of 0.05% (w/v) Triton X-114 in a solution buffered at pH 8.4. In the preconcentration stage, the micellar solution was continuously injected into a flow system with four mini-columns packed with cotton, glass wool. or TNT compresses for phase separation. The analytes-containing micelles were eluted from the mini-columns by a stream of 3 mol L(-1) HCl solution and the analytes were determined by FAAS. Chemical and flow variables affecting the preconcentration of the analytes were studied. For 15 mL. of preconcentrated solution, the enhancement factors varied between 15.1 and 20.3, the limits of detection were approximately 4.5 and 0.75 mu g L(-1) for lead and cadmium, respectively. For a solution containing 100 and 10 mu g L(-1) of lead and cadmium, respectively, the R.S.D. values varied from 1.6 to 3.2% (n = 7). The accuracy of the preconcentration system was evaluated by recovery measurements on spiked water samples. The method was susceptible to matrix effects, but these interferences were minimized by adding barium ions as masking agent in the sample solutions, and recoveries from spiked sample varied in the range of 95.1-107.3%. (C) 2008 Elsevier B.V. All rights reserved.

Elevated levels of selenium in the typical diet of Amazonian riverside populations

Selenium (Se) intake is generally from food, whose Se content depends on soil Se and plant accumulation. For humans, adequate Se intake is essential for several selenoenzymes. In the Lower Tapajos region of the Brazilian Amazon, Se status is elevated with large inter-community variability. Se intake in this region, where Hg exposure is among the highest in the world, may be important to counteract mercury (Hg) toxicity. The present study was conducted in 2006 with 155 persons from four communities of the Lower Tapajos. The objectives were: i) to evaluate Se content in their typical diet and drinking water; ii) to compare food Se concentrations with respect to geographic location; and iii) to examine the contribution of consumption of different food items to blood Se. More than 400 local foods and 40 drinking water samples were collected. Participants responded to an interview-administered food frequency questionnaire and provided blood samples. Food, water and blood Se levels were assessed by ICP-MS. Since Brazil nuts may also contain significant levels of barium (Ba) and strontium (Sr), these elements were likewise analyzed in nuts. The highest Se concentrations were found in Brazil nuts, but concentrations were highly variable (median: 13.9 mu g/g; range: 0.4-158.4 mu g/g). Chicken, game meat, eggs and beef also contained considerable levels of Se, with median concentrations from 0.3 to 1.4 mu g/g. There was no particular geographic distribution of food Se. Se concentration in drinking water was very low (<1.4 mu g/L). Blood Se covered a (103-1500 mu g/L), and was positively related to regular consumption of Brazil nuts, domestic chicken and game meat. Brazil nuts were found to contain highly variable and often very high concentrations of Ba (88.0 mu g/g, 1.9-1437 mu g/g) and Sr (38.7 mu g/g, 3.3-173 mu g/g). Further studies should address multiple nutrient/toxic interactions in the diet and related effects on health. (c) 2010 Elsevier B.V. All rights reserved.

Long-term follow up of abdominal rectosigmoidectomy with posterior end-to-side stapled anastomosis for Chagas megacolon

Aim Chagas` disease is an endemic parasitosis found in Latin America. The disease affects different organs, such as heart, oesophagus, colon and rectum. Megacolon is the most frequent long-term complication, caused by damage to the myoenteric and submucous plexus, ultimately leading to a functional barrier to the faeces. Patients with severe constipation are managed surgically. The study aimed to analyse the 10-year minimum functional outcome after rectosigmoidectomy with posterior end-to-side anastomosis (RPESA). Method A total of 21 of 46 patients were available for follow up. Patients underwent clinical, radiological and manometric evaluation, and the results were compared with preoperative parameters. Results Of the 21 patients evaluated, 81% (17) were female, with a mean age of 60.6 years. Good function was achieved in all patients, with significant improvement in defaecatory frequency (P < 0.0001), usage of enemas (P < 0.0001) and patient satisfaction. Barium enema also showed resolution of the colonic and rectal dilatation in 19 cases evaluated postoperatively. Conclusion Minimal 10-year follow up of RPESA showed excellent functional results, with no recurrence of constipation.

Evaluation of swallowing in children with vomiting after feeding

Vomiting after feeding is a symptom of gastroesophageal reflux (GER) and of eosinophilic esophagitis (EE), which are considered to be a cause of infant feeding disorder. The objective of the present study was to evaluate swallowing in children with feeding disorder manifested by vomiting after feeding. Using clinical and videofluoroscopic methods we studied the swallowing of 37 children with vomiting after feeding (mean age = 15.4 months), and of 15 healthy children (mean age = 20.5 months). In the videofluoroscopic examination the children swallowed a free volume of milk and 5 ml of mashed banana, both mixed with barium sulfate. We evaluated five swallows of liquid and five swallows of paste. The videofluoroscopic examination was recorded at 60 frames/s. Patients had difficulty during feeding, pneumonia, respiratory distress, otitis, and irritability more frequently than controls. During feeding, children with vomiting, choke were irritable, and refused food more frequently than controls, and during the videofluoroscopic examination the patients had more backward movement of the head than controls for both the liquid and paste boluses. There was no difference in the timing of oral swallowing transit, pharyngeal swallowing transit, or pharyngeal clearance between patients and controls. We conclude that children with vomiting after feeding may have difficulties in accepting feeding, although they have no alteration of oral and pharyngeal phases of swallowing.

Effect of Gender on Swallow Event Duration Assessed by Videofluoroscopy

There are data suggesting that women swallow liquids at a lower flow rate and ingest smaller volumes in each swallow than men. Our objective in this work was to compare swallowing in asymptomatic men and women by videofluoroscopy. We studied 18 men [age = 33-77 years, mean = 61 (10) years] and 12 women [age = 29-72 years, mean = 53 (15) years] who swallowed in duplicate 5 and 10 ml of liquid and paste barium boluses. None of the volunteers had dysphagia, neurologic diseases, or oral, pharyngeal, or esophageal diseases. The videofluoroscopic examination showed that for the 5-ml bolus, women had a longer oropharyngeal transit [liquid: men, 0.63 (0.21) s, women, 0.88 (0.39) s; paste: men, 0.64 (0.35) s, women, 0.94 (0.58) s], longer oral transit [liquid: men, 0.41 (0.21) s, women, 0.59 (0.35) s; paste: men, 0.39 (0.28) s, women, 0.59 (0.42) s], and longer pharyngeal clearance [liquid: men, 0.36 (0.11) s, women, 0.45 (0.16) s; paste: men, 0.42 (0.25) s, women, 0.56 (0.27) s] compared with men (p < 0.05). We conclude that there are differences in swallowing between men and women, with women having a longer oropharyngeal transit than men for a 5-ml bolus.

Contraction stress related to composite inorganic content

Objectives. The role of inorganic content on physical properties of resin composites is well known. However, its influence on polymerization stress development has not been established. The aim of this investigation was to evaluate the influence of inorganic fraction on polymerization stress and its determinants, namely, volumetric shrinkage, elastic modulus and degree of conversion. Methods. Eight experimental composites containing 1:1 BisGMA (bisphenylglycidyl dimethacrylate): TEGDMA (triethylene glycol dimethacrylate) (in mol) and barium glass at increasing concentrations from 25 to 60 vol.% (5% increments) were tested. Stress was determined in a universal test machine using acrylic as bonding substrate. Nominal polymerization stress was obtained diving the maximum load by the cross-surface area. Shrinkage was measured using a water picnometer. Elastic modulus was obtained by three-point flexural test. Degree of conversion was determined by FT-Raman spectroscopy. Results. Polymerization stress and shrinkage showed inverse relationships with filler content (R(2) = 0.965 and R(2) = 0.966, respectively). Elastic modulus presented a direct correlation with inorganic content (R(2) = 0.984). Degree of conversion did not vary significantly. Polymerization stress showed a strong direct correlation with shrinkage (R(2) = 0.982) and inverse with elastic modulus (R(2) = 0.966). Significance. High inorganic contents were associated with low polymerization stress values, which can be explained by the reduced volumetric shrinkage presented by heavily filled composites. (C) 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

BisGMA/TEGDMA ratio and filler content effects on shrinkage stress

Objective. To investigate the contributions of BisGMA:TEGDMA and filler content on polymerization stress, along with the influence of variables associated with stress development, namely, degree of conversion, reaction rate, shrinkage, elastic modulus and loss tangent for a series of experimental dental composites. Methods. Twenty formulations with BisGMA: TEGDMA ratios of 3: 7, 4: 6, 5: 5, 6: 4 and 7: 3 and barium glass filler levels of 40, 50, 60 or 70 wt% were studied. Polymerization stress was determined in a tensilometer, inserting the composite between acrylic rods fixed to clamps of a universal test machine and dividing the maximum load recorded by the rods cross-sectional area. Conversion and reaction rate were determined by infra-red spectroscopy. Shrinkage was measured by mercury dilatometer. Modulus was obtained by three-point bending. Loss tangent was determined by dynamic nanoindentation. Regression analyses were performed to estimate the effect of organic and inorganic contents on each studied variable, while a stepwise forward regression identified significant variables for polymerization stress. Results. All variables showed dependence on inorganic concentration and monomeric content. The resin matrix showed a stronger influence on polymerization stress, conversion and reaction rate, whereas filler fraction showed a stronger influence on shrinkage, modulus and loss tangent. Shrinkage and conversion were significantly related to polymerization stress. Significance. Both the inorganic filler concentration and monomeric content affect polymerization stress, but the stronger influence of the resin matrix suggests that it may be possible to reduce stress by modifying resin composition without sacrificing filler content. The main challenge is to develop formulations with low shrinkage without sacrificing degree of conversion. (C) 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Radiopacity of Portland Cement Associated With Different Radiopacifying Agents

This study evaluated the radiopacity of Portland cement associated with the following radiopacifying agents: bismuth oxide, zinc oxide, lead oxide, bismuth subnitrate, bismuth carbonate, barium sulfate, iodoform, calcium tungstate, and zirconium oxide. A ratio of 20% radiopacifier and 80% white Portland cement by weight was used for analysis. Pure Portland cement and dentin served as controls. Cement/radiopacifier and dentin disc-shaped specimens were fabricated, and radiopacity testing was performed according to the ISO 6876/2001 standard for dental root sealing materials. Using Insight occlusal films, the specimens were radiographed near to a graduated aluminum stepwedge varying from 2 to 16 mm in thickness. The radiographs were digitized and radiopacity compared with the aluminum stepwedge using Digora software (Orion Corporation Soredex, Helsinki, Finland). The radiographic density data were converted into mmAl and analyzed statistically by analysis of variance and Tukey-Kramer test (alpha = 0.05). The radiopacity of pure Portland cement was significantly lower (p < 0.05) than that of dentin, whereas all cement/radiopacifier mixtures were significantly more radiopaque than dentin and Portland cement alone (p < 0.05). Portland cement/bismuth oxide and Portland cement/lead oxide presented the highest radiopacity values and differed significantly from the other materials (p < 0.05), whereas Portland cement/zinc oxide presented the lowest radiopacity values of all mixtures (p < 0.05). All tested substances presented higher radiopacity than that of dentin and may potentially be added to the Portland cement as radiopacifying agents. However, the possible interference of the radiopacifiers with the setting chemistry, biocompatibility, and physical properties of the Portland cement should be further investigated before any clinical recommendation can be done. (J Endod 2009,35:737-740)

In vitro wear, surface roughness and hardness of propanal-containing and diacetyl-containing novel composites and copolymers based on bis-GMA analogs

Objective. To evaluate the effect of two additives, aldehyde or diketone, on the wear, roughness and hardness of bis-GMA-based composites/copolymers containing TEGDMA, propoxylated bis-GMA (CH(3)bis-GMA) or propoxylated fluorinated bis-GMA (CF(3)bis-GMA). Methods. Fifteen experimental composites and 15 corresponding copolymers were prepared combining bis-GMA and TEGDMA, CH3bis-GMA or CF3bis-GMA, with aldehyde (24mol% and 32 mol%) or diketone (24 mol% and 32 mol%) totaling 30 groups. For composites, hybrid treated filler (barium aluminosilicate glass/pyrogenic silica; 60 wt%) was added to monomer mixtures. Photopolymerization was affected by 0.2 wt% each of camphorquinone and N,N-dimethyl-p-toluidine. Wear (W) test was conducted in a toothbrushing abrasion machine (n = 6) and quantified using a profilometer. Surface roughness (R) changes, before and after abrasion test, were determined using a rugosimeter. Microhardness (H) measurements were performed for dry and wet samples using a Knoop microindenter (n = 6). Data were analyzed by one-way ANOVA and Tukey`s test (alpha = 0.05). Results. Incorporation of additives led to improved W and H values for bis-GMA/TEGDMA and bis-GMA/CH(3)bis-GMA systems. Additives had no significant effect on the W and H changes of bis-GMA/CF(3)bis-GMA. With regard to R changes, additives produced decreased values for bis-GMA/CH3bis-GMA and bis-GMA/CF3bis-GMA composites. Bis-GMA/TEGDMA and bis-GMA/CH(3)bis-GMA copolymers with additives became smoother after abrasion test. Significance. The findings correlate with additives ability to improve degree of conversion of some composites/copolymers thereby enhancing mechanical properties. Published by Elsevier Ltd on behalf of Academy of Dental Materials

What We Don't Know Could Hurt Us: A Single Center Study of Batch-to-Batch Variability of Dietary Fluids and Matched Videofluoroscopy Fluids

This study examines batch-to-batch variability in the production of dietary fluids and videofluoroscopy fluids of a single hospital. The material properties, such as viscosity, yield stress, and density, show significant variations between batches. Also waterbased products (i.e., cordial) provide (a) the most stability from week to week for both dietary and videofluoroscopy fluids and (b) the best dietary and videofluoroscopy fluid matches. The study also highlights the need for further research into how base substances, such as water, juice, and dairy products, react with different thickeners and with barium.

Ion transport induced by proteinase-activated receptors (PAR2) in colon and airways

Protease-activated receptors type 2 (PAR2) are activated by serine proteases like trypsin and mast cell tryptase. The function and physiological significance of PAR2 receptors is poorly understood, but recent studies suggest a role during inflammatory processes in both airways and intestine. PAR2 receptors are also likely to participate in the control of ion transport in these tissues. We demonstrate that stimulation of PAR2 in airways and intestine significantly enhanced ion transport. Trypsin induced CI- secretion in both airways and intestine when added to the basolateral but not to the luminal side of these tissues. In both airways and intestine, stimulation of ion transport was largely dependent on the increase in intracellular Ca2+. Effects of trypsin were largely reduced by basolateral bumetanide and barium and by trypsin inhibitor. Thrombin, an activator of proteinase-activated receptors types 1, 3, and 4 had no effects on equivalent short-circuit current in either airways or intestine. Expression of PAR2 in colon and airways was further confirmed by reverse transcription-polymerase chain reaction. We postulate that these receptors play a significant role in the regulation of electrolyte transport, which might be important during inflammatory diseases of airways and intestine.

Activation of ion secretion via proteinase-activated receptor-2 in human colon

Proteinase-activated receptor (PAR) type 2 (PAR-2) has been shown to mediate ion secretion in cultured epithelial cells and rat jejunum. With the use of a microUssing chamber, we demonstrate the role of PAR-2 for ion transport in native human colonic mucosa obtained from 30 normal individuals and 11 cystic fibrosis (CF) patients. Trypsin induced Cl- secretion when added to the basolateral but not luminal side of normal epithelia. Activation of Cl- secretion by trypsin was inhibited by indomethacin and was further increased by cAMP in normal tissues but was not present in CF colon, indicating the requirement of luminal CF transmembrane conductance regulator. Effects of trypsin were largely reduced by low Cl-,by basolateral bumetanide, and in the presence of barium or clotrimazole, but not by tetrodotoxin. Furthermore, trypsin-induced secretion was inhibited by the Ca2+-ATPase inhibitor cyclopiazonic acid and in low-Ca2+ buffer. The effects of trypsin were almost abolished by trypsin inhibitor. Thrombin, an activator of PAR types 1, 3, and 4, had no effects on equivalent short-circuit currents. The presence of PAR-2 in human colon epithelium was confirmed by RT-PCR and additional experiments with PAR-2-activating peptide. PAR-2-mediated intestinal electrolyte secretion by release of mast cell tryptase and potentiation of PAR-2 expression by tumor necrosis factor-alpha may contribute to the hypersecretion observed in inflammatory processes such as chronic inflammatory bowel disease.

A technique to assess small-scale heterogeneity of chemical properties in soil aggregates

A new method is presented which allows the separation of the soil aggregate exterior from the aggregate core. The method employs a combination of aggregate freezing with rapid separation of aggregate exteriors using ultrasonic energy. The factors influencing the thickness of the removed aggregate surface layer include water content of the aggregate prior to freezing, temperature difference between that of the frozen aggregate and that of the liquid it is submerged in during sonification, sonification time and energy, and the type of the immersion liquid. The success of the method and the thickness of the removed aggregate surface were examined using barium ( Ba2+) as a tracer. Barium ( as BaCl2) is rapidly absorbed by soil and is present at only very low levels in natural soils. Surface layers of 0.2 - 0.4 cm thickness were successfully removed from aggregates of 1 - 4 cm diameter. Two examples are given from soils in northern NSW to demonstrate the occurrence of small- scale heterogeneity in soil chemical properties. Compared with the surface fraction, a 4 - 7% higher calcium concentration was found in the core fraction of a clay loam soil ( Dermosol). Conversely, on a cracking clay soil ( Vertosol), atrazine concentration was around 15 times greater in the aggregate surface fractions compared with core fractions. Compared with the traditional estimation of soil chemical properties on homogenised bulk soil samples, it is suggested that separate analysis of aggregate surface and core fractions could provide useful additional information on the relationships between soil properties and environmental responses.

Estudos de absorção de CO2 com soluções aminadas

A absorção química de dióxido de carbono (CO2) através de soluções aquosas de aminas tem sido estudada nos últimos anos devido à preocupação ambiental face ao aquecimento global. Nestes estudos, foram tidos como principais objectivos a realização de ensaios preliminares de absorção e desabsorção de CO2 em soluções aquosas de aminas bem como a construção de uma instalação piloto para a mesma finalidade. Inicialmente, a nível laboratorial, procedeu-se à absorção de CO2 através de soluções aquosas de aminas. As aminas utilizadas nestes estudos foram a monoetanolamina (MEA), etilenodiamina (EDA), 1,6- hexanodiamina (HDA) e piperazina anidra (PZ). A absorção de CO2 através destas aminas foi realizada experimentalmente às condições normais de pressão e temperatura. A concentração das soluções aquosas foi de 20% em massa de cada amina. Foram também realizados estudos de regeneração das soluções aquosas de aminas saturadas de CO2 em banho de glicerina, para determinar as condições de regeneração. Para além disso, observou-se o estado físico das aminas no estado puro até saturação com CO2 para garantir a não ocorrência de danos a nível de entupimento numa posterior utilização na instalação piloto. Por fim, voltaram-se a repetir todos estes ensaios experimentais utilizando-se, em vez da água destilada, um solvente polar aprótico, dimetilsulfóxido (DMSO). Numa segunda fase destes estudos, a absorção de CO2 através de soluções aquosas de aminas foi investigada experimentalmente numa instalação piloto. O objectivo era utilizar nesta fase do estudo as mesmas aminas utilizadas nos ensaios preliminares mas uma vez que não se dispunha das quantidades necessárias de aminas e para a sua aquisição teria que se despender bastante tempo e dinheiro, utilizaram-se duas soluções aquosas de alcanolaminas. As alcanolaminas utilizadas no presente estudo foram a amina secundária dietanolamina (DEA) e a amina terciária N-metildietanolamina (MDEA), duas aminas amplamente utilizadas nas indústrias químicas e petroquímicas para a purificação dos gases de combustão. A absorção de CO2 através destas duas alcanolaminas foi realizada experimentalmente às condições normais de pressão e temperatura. As concentrações das soluções aquosas foram de (10, 20 e 30) % em massa de MDEA e de DEA. O processo de adição de cloreto de bário (BaCl2.2H2O) às alcanolaminas ajuda à formação de carbonato de bário, quando o CO2 passa através da solução de alcanolamina. A quantidade de carbonato de bário formado foi utilizado para determinar a solubilidade do CO2 (mol CO2/mol alcanolamina). O principal desafio na captura de CO2 dos gases de combustão é o de reduzir o consumo de energia necessária para a regeneração do solvente. Deste modo, foram também realizados estudos de regeneração das soluções de alcanolaminas saturadas, para determinar as condições de regeneração. Os resultados obtidos, a nível laboratorial, revelaram que uma amina secundária (PZ) e uma amina primária de cadeia longa (HDA) são mais favoráveis ao processo de absorção e regeneração de CO2. No entanto, e devido a essa mesma estrutura molecular, necessitam de maiores valores de temperaturas para desabsorver o CO2. Garantiu-se poder trabalhar com as quatro aminas no estado puro em estudos futuros, na instalação piloto, garantindo que não ocorrerão danos a nível de entupimento. Relativamente ao solvente utilizado concluiu-se que um solvente polar aprótico não é um solvente favorável para estes estudos. Os resultados obtidos, na instalação piloto, revelaram que a amina terciária, MDEA, consegue absorver maiores quantidades de CO2 do que a amina secundária, EDA, bem como é a mais fácil de regenerar com menor perda de capacidade de absorção do que a EDA.

Construction and evaluation of cysteine selective electrodes for FIA analysis of pharmaceuticals

A flow injection analysis (FIA) system comprising a cysteine selective electrode as detection system was developed for determination of this amino acid in pharmaceuticals. Several electrodes were constructed for this purpose, having PVC membranes with different ionic exchangers and mediator solvents. Better working characteristics were attained with membranes comprising o-nitrophenyl octyl ether as mediator solvent and a tetraphenylborate based ionic-sensor. Injection of 500 µL standard solutions into an ionic strength adjuster carrier (3x10-3 M) of barium chloride flowing at 2.4mL min-1, showed linearity ranges from 5.0x10-5 to 5.0x10-3 M, with slopes of 76.4±0.6mV decade-1 and R2>0.9935. Slope decreased significantly under the requirement of a pH adjustment, selected at 4.5. Interference of several compounds (sodium, potassium, magnesium, barium, glucose, fructose, and sucrose) was estimated by potentiometric selectivity coefficients and considered negligible. Analysis of real samples were performed and considered accurate, with a relative error to an independent method of +2.7%.