Aplicação de radiação UV artificial e solar no tratamento fotocatalítico de efluentes de curtume

Tannery effluents are very dangerous for the environment since they contain large amounts of dangerous and biorecalcitrant contaminants (organic matter and Cr(VI)). This paper reports the efficiency of heterogeneous photocatalysis, based on the application of solar and artificial radiation, furnished by UV lamps, using TiO2 fixed on a flat plate, in the treatment of synthetic effluents. The results of COD and Cr(VI) demonstrate that the use of solar radiation is the most efficient way to perform the photocatalytic treatment of these effluents since a minimum removal of 62 and 61% was observed for Cr(VI) and organic matter, respectively.

Degradação do pesticida Padron® por processos fotoquímicos utilizando luz artificial e solar

Destruction of Padron® (dye and picloram) was evaluated using a photoreactor and a solar reactor. Photolysis was observed using only a germicide lamp (GL). Black light (BL) and H2O2 (172 mmol L-1) promoted a conversion of 49% and 6% of dye and picloram, respectively. Photocatalytic processes were more efficient using TiO2/GL (96%-dye; 60%-picloram) than TiO2/BL (44%-dye; 40%-picloram). Photolysis using sunlight was not observed during PadronÒ recirculation in the reactor constructed with four borosilicate tubes. Meanwhile, adding H2O2 resulted in 12% conversion of dissolved organic compounds. Finally, the most efficient mineralization (60%) was obtained using the Fenton reaction ( H2O2-176 mmol L-1; FeSO4x6H2O-90 mmol L-1) and sunlight.

Thylakoid Protein Phosphorylation in Regulation of Photosynthesis

Once the seed has germinated, the plant is forced to face all the environmental changes in its habitat. In order to survive, plants have evolved a number of different acclimation systems. The primary reaction behind plant growth and development is photosynthesis. Photosynthesis captures solar energy and converts it into chemical form. Photosynthesis in turn functions under the control of environmental cues, but is also affected by the growth, development, and metabolic state of a plant. The availability of solar energy fluctuates continuously, requiring non-stop adjustment of photosynthetic efficiency in order to maintain the balance between photosynthesis and the requirements and restrictions of plant metabolism. Tight regulation is required, not only to provide sufficient energy supply but also to prevent the damage caused by excess energy. The very first reaction of photosynthesis is splitting of water into the form of oxygen, hydrogen, and electrons. This most fundamental reaction of life is run by photosystem II (PSII), and the energy required for the reaction is collected by the light harvesting complex II (LHCII). Several proteins of the PSII-LHCII complex are reversibly phosphorylated according to the energy balance between photosynthesis and metabolism. Thylakoid protein phosphorylation has been under extensive investigation for over 30 years, yet the physiological role of phosphorylation remains elusive. Recently, the kinases behind the phosphorylation of PSII-LHCII proteins (STN7 and STN8) were identified and the knockout mutants of these kinases became available, providing powerful tools to elucidate the physiological role of PSII-LHCII phosphorylation. In my work I have used the stn7 and stn8 mutants in order to clarify the role of PSII-LHCII phosphorylation in regulation and protection of the photosynthetic machinery according to environmental cues. I show that STN7- dependent PSII-LHCII protein phosphorylation is required to balance the excitation energy distribution between PSII and PSI especially under low light intensities when the excitation energy transfer from LHC to PSII and PSI is efficient. This mechanism differs from traditional light quality-induced “state 1” – “state 2” transition and ensures fluent electron transfer from PSII to PSI under low light, yet having highest physiological relevance under fluctuating light intensity. STN8-dependent phosphorylation of PSII proteins, in turn, is required for fluent turn-over of photodamaged PSII complexes and has the highest importance upon prolonged exposure of the photosynthetic apparatus to excess light.

Efeito do intemperismo artificial em quatro madeiras tropicais monitorado por espectroscopia de infravermelho (DRIFT)

Four tropical woods, were investigated to compare their performance and natural resistances to artificial weathering using the diffuse reflectance infrared Fourier transform spectroscopy (DRIFT). The species were garapeira (Apuleia leiocarpa), itaúba (Mezilaurus itauba) and tauari (Couratari sp.), woods traditionally indicated for exterior uses, and marupá (Simarouba amara), that served as reference. The samples were submitted to cycles of UV radiation (350 nm) and water until 2,000 h. The photodegradation processes of woods surfaces were accomplished monitoring the changes in the intensities associated to lignin (1508 cm-1) and carbonyl group (1736 cm-1) absorptions. The results have shown that lignin was the first component to be photodegradated, resulting in surfaces mainly composed by cellulose, after 2,000 h of UV irradiation. The processes of formation and lixiviation of carbonyl compounds were different for each species. The experimental conditions used in this work were too severe to evaluate the wood density and extractives content influences during the treatment.

Projecte constructiu de llac artificial situat a la Bonaigua a l’estació d’esquí de Baqueira-Beret (Vall d’Aran)

El document té per objecte la definició a nivell constructiu de les obres de implantació d’una nova captació, un nou llac artificial, i la canonada de connexió per a la producció de neu artificial a l’estació d’esquí de Baqueira-Beret (Vall d’Aran), concretament a la zona de Bonaigua.

Estudio gráfico básico de lago artificial situado en Argulls. Estación de esquí de Baqueira-Beret. Vall d’Aran.

Propuesta gráfica de nuevo lago artificial en Argulls. Estación de esquí de Baqueria-Beret

Aplicação de técnicas multivariadas e inteligência artificial na análise de espectros de infravermelho para determinação de matéria orgânica em amostras de solos

In this paper studies based on Multilayer Perception Artificial Neural Network and Least Square Support Vector Machine (LS-SVM) techniques are applied to determine of the concentration of Soil Organic Matter (SOM). Performances of the techniques are compared. SOM concentrations and spectral data from Mid-Infrared are used as input parameters for both techniques. Multivariate regressions were performed for a set of 1117 spectra of soil samples, with concentrations ranging from 2 to 400 g kg-1. The LS-SVM resulted in a Root Mean Square Error of Prediction of 3.26 g kg-1 that is comparable to the deviation of the Walkley-Black method (2.80 g kg-1).

Time-series forecasting of pollutant concentration levels using particle swarm optimization and artificial neural networks

This study evaluates the application of an intelligent hybrid system for time-series forecasting of atmospheric pollutant concentration levels. The proposed method consists of an artificial neural network combined with a particle swarm optimization algorithm. The method not only searches relevant time lags for the correct characterization of the time series, but also determines the best neural network architecture. An experimental analysis is performed using four real time series and the results are shown in terms of six performance measures. The experimental results demonstrate that the proposed methodology achieves a fair prediction of the presented pollutant time series by using compact networks.

Simple method for mass production of polypyrrole/carbon nanotubes hybrid artificial muscle

Large scale preparation of hybrid electrical actuators represents an important step for the production of low cost devices. Interfacial polymerization of polypyrrole in the presence of multi-walled carbon nanotubes represents a simple technique in which strong interaction between components is established, providing composite materials with potential applications as actuators due to the synergistic interaction between the individual components, i.e., fast response of carbon nanotubes, high strain of polypyrrole, and diversity in the available geometry of resulting samples.

Inoculação artificial de colmos de milho em diferentes idades e concentrações de inóculo e sua relação com a expressão da resistência a fusarium moniliforme

A podridão do colmo de milho (Zea mays) causada por Fusarium moniliforme tem ocorrência generalizada nas regiões produtoras do Brasil. Visando obter informações sobre o comportamento da doença, foram conduzidos dois experimentos em campo, um inoculando-se artificialmente colmo de plantas aos 30, 55 e 80 dias após a semeadura, e outro testando-se diferentes concentrações de inóculo, 1x10(4), 5x10(5) e 1x10(7) conídios/ml, aplicadas aos 55 dias após a semeadura. Nesses experimentos utilizou-se o delineamento de blocos ao acaso, com respectivamente, quatro e cinco repetições, sendo cada parcela constituída de 50 plantas. As inoculações foram feitas no centro do segundo entrenó alongado acima do solo. A avaliação da doença foi realizada aos 120 dias após a semeadura, com base na sintomatologia interna do colmo, utilizando uma escala de notas variando de 1 a 9. Por ocasião da colheita foram avaliados o número de plantas acamadas e a produção de grãos. Procedeu-se também a análise do teor de lignina e tanino da casca e da parte interna do entrenó inoculado nos diferentes tratamentos. Todas as concentrações de inóculo testadas permitiram diferenciar os níveis de resistência dos híbridos, sendo estes decrescentes a partir do Cargill 333 para o Cargill 901, tendo o Dina 766 um comportamento intermediário. Por outro lado, não houve diferenças significativas para as inoculações em diferentes épocas. Os teores de taninos não foram significativamente diferentes entre os híbridos, já o teor de lignina foi significativamente relacionado com o nível de resistência dos três híbridos avaliados.

Effect of population densities of Heterodera glycines race 3 on leaf area, photosynthesis and yield of soybean

The effect of Heterodera glycines on photosynthesis, leaf area and yield of soybean (Glycine max) was studied in two experiments carried out under greenhouse condition. Soybean seeds were sown in 1.5 l (Experiment 1) or 5.0 l (Experiment 2) clay pots filled with a mixture of field soil + sand (1:1) sterilized with methyl bromide. Eight days after sowing, seedlings were thinned to one per pot, and one day later inoculated with 0; 1.200; 3.600; 10.800; 32.400 or 97.200 J2 juveniles of H. glycines. Experiment 1 was carried out during the first 45 days of the inoculation while Experiment 2 was conducted during the whole cycle of the crop. Measurements of photosynthetic rate, stomatic conductance, chlorophyll fluorescence, leaf color, leaf area, and chlorophyll leaf content were taken at ten-day intervals throughout the experiments. Data on fresh root weight, top dry weight, grain yield, number of eggs/gram of roots, and nematode reproduction factor were obtained at the end of the trials. Each treatment was replicated ten times. There was a marked reduction in both photosynthetic rate and chlorophyll content, as well as an evident yellowing of the leaves of the infected plants. Even at the lowest Pi, the effects of H. glycines on the top dry weight or grain yield were quite severe. Despite the parasitism, soybean yield was highly correlated with the integrated leaf area and, accordingly, the use of this parameter was suggested for the design of potential damage prediction models that include physiological aspects of nematode-diseased plants.

Resistência de cultivares de trigo à giberela mediante inoculação artificial em espiguetas

Este trabalho teve como objetivo determinar a concentração ótima de conídios de F. graminearumpara inoculação artificial em espiguetas de trigo e verificar o tipo de resistência à giberela (Tipo I e/ou II) dos cultivares de trigo. O trabalho foi composto por dois experimentos, sendo que no primeiro determinou-se a concentração ótima de conídios mL-1 para inoculação artificial em quatro cultivares. Para isso, testou-se as concentraçóes de 5x103, 15x103, 25x103, 35x103 e 40x103 conídios mL-1. Vinte e um dias após a inoculação quantificou-se a incidência de F. graminearum em espiguetas, sendo que através de análise de regressão, determinou-se a concentração ótima de conídios mL-1 para cada cultivar. No segundo experimento, avaliou-se a resistência à giberela dos cultivares de trigo mediante inoculação artificial, utilizou-se a mesma metodologia do experimento anterior e a concentração de 31x103conídios mL-1. As variáveis avaliadas foram severidade, grão giberelados e incidência em espiguetas gibereladas. A melhor concentração para inoculação artificial de giberela em espiguetas de trigo é de 31x103conídios mL-1. A maior severidade da doença foi verificada para os cultivares de trigo BRS 208 e Pampeano e a maior percentagem de grão giberelado foi para o cultivar BRS 208. Os cultivares Pampeano e BRS 177 não apresentaram resistência do Tipo I à giberela, porém apresentam do Tipo II, enquanto que os cultivares Mirante e BRS 208 não apresentam nenhum dos dois tipos de resistência.

Efeito da desrama artificial na qualidade da madeira de clones de eucalipto em sistema agrossilvipastoril

O objetivo do presente trabalho foi avaliar o efeito da desrama artificial na qualidade da madeira de clones de eucalipto, em sistema agrossilvipastoril, na fazenda Riacho, pertencente à Companhia Mineira de Metais, município de Paracatu-MG, Brasil. O experimento foi instalado em dezembro de 1994, com o plantio das mudas de três clones de híbridos naturais de Eucalyptus camaldulensis Dehnh. (código 06) e de Eucalyptus urophylla S.T. Blake (código 13 e 44), no espaçamento de 10 x 4 m. O delineamento experimental utilizado foi o de blocos casualizados, com três repetições. Os tratamentos foram dispostos em esquema de parcelas subdivididas, sendo os tratamentos primários constituídos pelos clones e os tratamentos secundários definidos por: T1- sem desrama; T2- desrama a 2 m; T3- desrama a 4 m; e T4- desrama a 6 m. Para avaliação da qualidade da madeira foram obtidos, no ano de 2000, a densidade básica da madeira, o número e o diâmetro dos nós, a nodosidade, o número de bolsas de resina e a conicidade das árvores. Os resultados obtidos mostraram que a densidade básica da madeira por árvore apresentou variações significativas entre os clones e as alturas de desrama. A densidade básica ao longo do tronco apresentou comportamento diferenciado perante os clones e as alturas de desrama. O número de nós e a nodosidade foram afetados pelas alturas de desrama. A conicidade e o número de bolsas de resina não foram afetados pelas alturas de desrama, apresentando diferença significativa somente entre os clones.

Effects of different light levels on the initial growth and photosynthesis of Croton urucurana Baill. in southeastern Brazil

Four levels of shading (full sunlight (0%), 30, 50, 70% of solar radiation interception on growth, chlorophyll concentration and photosynthetic rate were studied in Croton urucurana Baill., a pioneer plant species. This species seedlings are of potential interest for reforestation projects and recovery of degraded areas. The seedlings were grown in pots containing soil and sand (2:1) and later transferred to plastic bags of 3 dm³ and submitted to different levels of shading (30, 50, 70%) of solar radiation and full sunlight, as control. The experimental design was completely randomized with five replicates and each experimental unit was composed of five plants. The results suggest that plants submitted to 70% shading showed higher dry weight accumulation in leaf and root, and higher plant height and leaf area. However, the seedlings root system showed higher dry biomass under full sunlight. It was observed a tendency to increase chlorophyll concentration and to decrease photosynthetic rate with the increase of the shading level.

Quantificação da falha na madeira em juntas coladas utilizando técnicas de visão artificial

Com o emprego de adesivos pode-se obter um grande número de produtos derivados da madeira. Para confecção industrial de produtos de madeira colada, normas reconhecidas internacionalmente exigem que a adesão da madeira seja testada segundo procedimentos padronizados e que nos resultados destes testes seja reportado, além da resistência das juntas, o porcentual de falha na madeira. Para avaliação da falha a norma ASTM D5266-99 recomenda o emprego de uma rede de quadrículas traçada sobre um material transparente. Contudo, esta avaliação, além de demandar muito tempo, ainda é realizada com muita subjetividade. A hipótese do presente trabalho é que se pode quantificar a falha na madeira com um sistema de visão artificial, tornando o procedimento mais rápido e menos sujeito à subjetividade. Foram testados dois tipos de algoritmos de limiarização automática em imagens adquiridas com digitalizadores de mesa. Concluiu-se que a falha na madeira pode ser quantificada por limiarização automática em substituição ao método convencional das quadrículas. Os algoritmos testados apresentaram erro médio absoluto menor que 3% em relação ao sistema convencional da rede quadriculada.