Performance analysis of AlGaAs/GaAs tunnel junctions for ultra-high concentration photovoltaics

An n(++)-GaAs/p(++)-AlGaAs tunnel junction with a peak current density of 10 100Acm(-2) is developed. This device is a tunnel junction for multijunction solar cells, grown lattice-matched on standard GaAs or Ge substrates, with the highest peak current density ever reported. The voltage drop for a current density equivalent to the operation of the multijunction solar cell up to 10 000 suns is below 5 mV. Trap-assisted tunnelling is proposed to be behind this performance, which cannot be justified by simple band-to-band tunnelling. The metal-organic vapour-phase epitaxy growth conditions, which are in the limits of the transport-limited regime, and the heavy tellurium doping levels are the proposed origins of the defects enabling trap-assisted tunnelling. The hypothesis of trap-assisted tunnelling is supported by the observed annealing behaviour of the tunnel junctions, which cannot be explained in terms of dopant diffusion or passivation. For the integration of these tunnel junctions into a triple-junction solar cell, AlGaAs barrier layers are introduced to suppress the formation of parasitic junctions, but this is found to significantly degrade the performance of the tunnel junctions. However, the annealed tunnel junctions with barrier layers still exhibit a peak current density higher than 2500Acm(-2) and a voltage drop at 10 000 suns of around 20 mV, which are excellent properties for tunnel junctions and mean they can serve as low-loss interconnections in multijunction solar cells working at ultra-high concentrations.

Biotransformações na obtenção de hidróxi-selenetos e hidróxi-teluretos quirais

Neste trabalho foi estudado o comportamento de hidróxi-calcogenetos (Se e Te) frente a biotransformações, empregando enzimas isoladas em meio orgânico ou aquoso e empregando microorganismos (fungos). Estudos comparativos sobre a influência de diversas variáveis, como solvente, temperatura, imobilização enzimática e estrutura do hidróxi-calcogeneto, foram realizados. Inicialmente os compostos foram sintetizados utilizando métodos descritos na literatura, em seguida foi estudada a resolução de hidróxiselenetos em meio orgânico empregando lipases isoladas (Esquema 1), (ver arquivo), incluindo um estudo de imobilização da PSL em diversos suportes, além do estudo da influência da variação do solvente, da temperatura, da lipase, etc. Na resolução em meio aquoso empregando enzimas isoladas, primeiramente os hidróxi-selenetos foram acetilados quimicamente e depois realizado uma triagem (com dez enzimas de diferentes fontes) empregando indicador de pH colori métrico. Posteriormente os acetatos dos hidróxi-selenetos (Esquema 2) (ver arquivo) foram submetidos à resolução enzimática em meio aquoso empregando as enzimas que foram selecionadas na triagem enzimática. As biotransformações utilizando fungos foram realizadas empregando células inteiras de algumas linhagens de Aspergillus terreus. Na seqüência foi realizada a resolução de hidróxi-teluretos em meio orgânico utilizando lipases isoladas (Esquema 3)(ver arquivo). Nessas resoluções também foi estudada a influência da variação do solvente, da lipase, do tempo, etc. De forma a demonstrar a importância dos compostos resolvidos, um hidróxi-seleneto quiral e dois hidróxi-teluretos quirais foram usados para preparar compostos pertencentes a classes de unidades estruturais de vasta ocorrência em produtos naturais: um álcool alílico e duas lactonas (Esquema 4)(ver arquivo).

Formação de ligação carbono-carbono através de compostos orgânicos de telúrio

Diversas classes de compostos orgânicos de telúrio foram exploradas neste trabalho. Inicialmente foi estudada a transmetalação entre teluretos alílicos e dibutil cianocupratos de lítio de ordem superior, levando aos respectivos cianocupratos alílicos de lítio. Estes, por sua vez, foram acoplados com triflatos vinílicos, importantes intermediários sintéticos preparados previamente a partir de teluretos vinílicos, levando a sistemas altamente insaturados em ótimos rendimentos (Esquema 1). (Ver no arquivo em PDF) Em seguida, foi explorada a reatividade de teluretos aromáticos frente a reagentes organometálicos. Cianocupratos arílicos, gerados a partir da transmetalação entre teluretos aromáticos com cianocupratos de lítio de ordem superior, foram adicionados a cetonas α,β -insaturadas, levando aos produtos de adição 1,4 em bons rendimentos (Esquema 2). (Ver no arquivo em PDF) Teluretos vinílicos funcionalizados de configuração Z também foram alvo de estudo visando a formação de ligação carbono-carbono. Reações de substituição entre estes teluretos e cianocupratos de lítio de ordem inferior levaram a cetonas e ésteres α,β- insaturados com estereoquímica defInida em ótimos rendimentos (Esquema 3). (Ver no arquivo em PDF) De agosto/20OJ a março/2004, a aluna realizou um estágio sanduíche na University of California, Santa Barbara, sob a orientação do Prof. Bruce H. Lipshutz, onde realizou estudos sobre a ciclização de Bergman, visando a síntese do fragmentobiarílico A-B da vancornicina. Diversas condições para a ciclização foram estudadas com um composto modelo (Esquema 4) (Ver no arquivo em PDF) e parte da síntese total do fragmento da vancomlcma, onde a ciclização seria a etapa-chave, foi realizada com sucesso (Esquema 5). (Ver no arquivo em PDF)

Background Measurement Techniques and Sensitivity Studies for the SNO+ Neutrinoless Double Beta Decay Search

The control of radioactive backgrounds will be key in the search for neutrinoless double beta decay at the SNO+ experiment. Several aspects of the SNO+ back- grounds have been studied. The SNO+ tellurium purification process may require ultra low background ethanol as a reagent. A low background assay technique for ethanol was developed and used to identify a source of ethanol with measured 238U and 232Th concentrations below 2.8 10^-13 g/g and 10^-14 g/g respectively. It was also determined that at least 99:997% of the ethanol can be removed from the purified tellurium using forced air ow in order to reduce 14C contamination. In addition, a quality-control technique using an oxygen sensor was studied to monitor 222Rn contamination due to air leaking into the SNO+ scintillator during transport. The expected sensitivity of the technique is 0.1mBq/L or better depending on the oxygen sensor used. Finally, the dependence of SNO+ neutrinoless double beta decay sensitivity on internal background levels was studied using Monte Carlo simulation. The half-life limit to neutrinoless double beta decay of 130Te after 3 years of operation was found to be 4.8 1025 years under default conditions.

Chemical and isotopic compositions of hydrothermal manifestations and minerals from the Broken Spur hydrothermal field

A representative collection of hydrothermal manifestations was sampled practically from all hydrothermal mounds of the Broken Spur hydrothermal vent field with use of the Mir manned submersibles during three cruises of R/V Akademik Mstislav Keldysh. Mineral associations characteristic for different morphological types of sulfide ores from hydrothermal pipes, plates, and diffusers are assessed. Particular attention is paid to distribution of minor elements and their distribution patterns determined by mineralogical zonation. Measured isotopic composition of sulfur in sulfide minerals varies from 0.4 to 5.2 per mil that indicates their similarity with ores from the Snake Pit vent field and is related to dilution of hot ore-bearing solutions by seawater and reduction of water sulfate ions to H2S with heavy isotopic composition.

Fe-Mn crusts from the Atlantic Ocean

Mineral and chemical compositions of a set of crust samples collected from the North, Central and South Atlantic were examined by means of analytical electron microscopy and ICP-MS, chemical, and microchemical elemental analysis. Vernadite, asbolane, and goethite are dominant mineral phases of the crusts, ferrihydrite is minor, hematite and feroxyhyte are rare. The samples show wide variability in major and trace element contents; however, their characteristic geochemical signatures indicate hydrogenous origin. A comparison between compositions of oceanic hydrogenous and hydrothermal crusts and metalliferous hydrothermal sediments from different ocean areas suggests that the geochemical approach may be insufficient in some cases and fail to identify hydrothermal input in ferromanganese crusts of mixed composition.

Comprehensive inorganic chemistry

Bibliographical footnotes.

The use of organotellurium heterocycles as precursors for novel organometallic compounds

The reactions of group 16 heterocycles with organometallic reagents are described. Thiophenes have been used as models for organic sulfur in coal and their reactivity towards triiron dodecacarbonyl has been investigated. Reaction of unsubstituted thiophene with Fe3(CO)12 results in desulfurisation of the heterocycle, with the organic fragment being recovered in the form of the ferrole, C4H4.Fe2(CO)6. In addition a novel organometallic compound of iron is isolated, the formula of which is shown to be C4H4.Fe3(CO)8. Bezothiophene reacts with Fe3(CO)12 to yield benzothiaferrole, C8H6S.Fe2(CO)6, in which the sulfur is retained in the heterocycle. Dibenzothiophene, a more accurate model for organic sulfur in coal, displays no reactivity towards the iron carbonyl, suggesting that the more condensed systems will desulfurise less readily. Microwave methodology has been successful in accelerating the reactions of thiophenes with Fe3(CO)12. However, reaction of benzothiophene does not proceed to the desulfurisation stage while dibenzothiophene is unreactive even under microwave conditions. Tellurophenes (Te analogues of thiophenes) are shown to mimic the behaviour of thiophenes towards certain organometallic reagents with the advantage that their greater reactivity enables recovery of products in higher yields. Hence, reaction of tellurophene with Fe3(CO)12 again affords the ferrole but with an almost ten-fold increase in yield over thiophene. More significantly, dibenzotellurophene is also detellurated by the iron carbonyl affording the previously inaccessible dibenzoferrole, C12H8.Fe2(CO)6, thereby demonstrating the mechanistic feasibility of dechalcogenation of the more condensed aromatic molecules. The potential of tellurium heterocycles to act as precursors for novel organometallics is also recognised owing to the relatively facile elimination of the heteroatom from these systems. Thus, 2-telluraindane reacts with Fe3(CO)12 to yield a novel organometallic compound of formula C16H16.Fe(CO)3, arising from the unsymmetric dimerisation of two organic fragments.

Mechanistic studies of organotellurium chemistry

The oxidation of bis(p-ethoxyphenyl) ditelluride by hydrogen peroxide has been studied kinetically. The reaction monitored was an oxidation from tellurium(I) to tellurium(II). The reaction stoichiometry ratio was found to depend upon the initial reagent concentrations. The presence of dioxygen was found to retard the rate and attributed to a dioxygen-ditelluride adduct. The rate varies in the following order of different atmospheres N2> Air> > O2. The final product obtained from the oxidation has been characterised by IR, NMR and ESR spectroscopy. A mechanism for the oxidation has been suggested. The reduction of p-EtOPhTeCl3 by the hydrazinium ion has been studied kinetically. The stoichiometric measurements show that four moles p-EtOPhTeCl3 are equivalent to three moles hydrazinium ion. The kinetics were studied under pseudo first order conditions. No ammonia was detected as a nitrogen containing product. The reduction proceeds via a two-electron process which indicates that it is inner-sphere in nature. A mechanism for the reduction is suggested. The solvolysis of p-EtOPhTeCl3 by methanol in benzene/methanol media has been studied. The study shows that the solvolysis is a reversible, acid catalysed reaction. Replacement of the chlorides on tellurium by methanol is agreed to be associative and replacement of the first chloride is rate determining. The rate of solvolysis varies in the order trichloride > tribromide > triiodide. A mechanism for the solvolysis is suggested. The synthesis of some tellurium heterocyclics is reported. The synthesis and characterisation of telluranthrene is reported. The attempted synthesis of telluraxanthene was unsuccessful.

Organometallic precursors for pillared clay synthesis

The synthetic hectorite, laponite has been used within the paper industry to produce mildly conducting paper for use in electrographic printing. The aim of this research was to modify laponite in order to improve the electrical conductivity. In a continuation of a previous investigation involving organotin intercalation of laponite, the organotin precursor (p-CH3,OC6H4)4Sn was synthesised and characterised using Mass Spectroscopy, Infrared Spectroscopy and elemental analysis. Results of intercalation with this compound and a range of organobismuth and organoantimony compounds suggested that a halide content within the precursor was necessary for improvement in conductivity to be observed. Organometallic intercalation of a range of organotellurium compounds with laponite provided evidence that a hydrolysis reaction on the clay surface followed by the release of hydrochloric acid was an important first step if a reaction was to occur with the clay. Atomic Absorption Spectroscopy studies have shown that the acid protons underwent exchange with the interlayer sodium ions in the clay to varying degrees. Gas-liquid Chromatography and Infrared Spectroscopy revealed that the carbon-tellurium bond remained intact. Powder X-ray diffraction revealed that there had been no increase in the basal spacing. The a.c. conductivity of the modified clays in the form of pressed discs was studied over a frequency range of 12Hz - 100kHz using two electrode systems, silver paste and stainless steel. The a.c. conductivity consists of two components, ionic and reactive. The conductivity of laponite was increased by intercalation with organometallic compounds. The most impressive increase was gained using the organotellurium precursor (p-CH3OC6H4)2TeCl2. Conductivity investigations using the stainless steel electrode where measurements are made under pressure showed that in the case of laponite, where poor particle-particle contact exists at ambient pressure, there is a two order of magnitude increase in the measured a.c. conductivity. This significant increase was not seen in modified laponites where the particle-particle contact had already been improved upon. Investigations of the clay surface using Scanning Electron Microscopy suggested that the improvement in particle-particle contact is the largest factor in the determination of the conductivity. The other important factor is the nature and the concentration of the interlayer cations. A range of clays were synthesised in order to increase the concentration of sodium interlayer cations. A sol-gel method was employed to carry out these syntheses. A conductivity evaluation showed that increasing the concentration of the sodium cations within the clay led to an increase in the conductivity.

Organotellurium compounds for metal organic vapour phase epitaxy

The infra-red detector material cadmium mercury telluride can be grown by the technique of Metal Organic Vapour Phase Epitaxy using simple alkyl telluride compounds as the source of tellurium. New tellurium precursors are required in order to overcome handling and toxicity problems and to reduce the growth temperature in preparing the material. A range of diaryltellurium(IV) dicarboxylates and some 2-(2'-pyridyl)phenyl-tellurium(II) and tellurium(IV) monocarboxylates have been synthesised and characterised by infra-red, 13C N.M.R. and mass spectroscopy. Infra-red spectroscopy has been used to determine the mode of bonding of the carboxylate ligand to tellurium. Synthetic methods have been devised for the preparation of diorganotritellurides (R2Te3) and mixed diorganotetrachalcogenides (RTeSeSeTeR). A mechanism for the formation of the tritellurides based on aerobic conditions is proposed. The reaction of ArTe- with (ClCH2CH2)3N leads to tripod-like multidentate ligands (ArTeCH2CH2)3N which form complexes with the ions Hg(II), Cd(II), Cu(I), Pt(II) and Pd(II). Synthetic routes to aryltelluroalkylamines and arylselenoalkylamines are also reported. The crystal structure of 2-(2'-pyridyl)phenyltellurium(II) bromide has been solved in which there are six molecules present within the unit cell. There are no close intermolecular Te---Te interactions and the molecules are stabilised by short Te---N intramolecular contacts. The crystal structure of 2-(2'-pyridyl)phenylselenium(II)-tribromomercurate(II) is also presented. A study of the Raman vibrational spectra of some tellurated azobenzenes and 2-phenylpyridines shows spectra of remarkably far superior quality to those obtained using infra-red spectroscopy.

The chemistry of some organotellurium compounds

Tbe formation of Pd(TeR)n and (CuTeR)n from the reaction between telluroesters and Pd(II)or Cu(II) suggested that these organa­tellurium reagents may be useful precursors of RTe- ligands in reactions with transition-metal substrates. Also the formation of telluronium salts Me2RTeI- from the reaction between telluroesters and methyl iodide, together with the above, confirm the cleavage of -cõ-Te bonds rather than -C-Te bonds. The formation of a carboxylic acid from the toluene solution of a ditelluride d palladium(O) complex in the presence of light oxygen (from air) is demonstrated. When the solvent employed is p-xylene an aldehyde is formed.The reaction proceeds via the free radical, RTeO, with Pd(PPh3)4 as a catalyst.It has also been shown that the oxidation of aldehydes to carboxylic acids is catalysed by ditelluride. Spin trapping experiments with PhCH=N(O)But (phenyl-t-butyl-nitrone) have provided evidence that the oxidative addition of an alkyl halide (RX=Mei, BunBr, BusecBr, ButBr, BrCH2-CH=CHCH2Br, and Br(CH2)4Br) to diphenyltelluride and reductive elimination of CH3SCN from Ph2(CH3)Te(NCS) proceeds via radical pathways. A mechanism is proposed for oxidative addition which involves the preformation of a charge transfer complex of alkyl halide and diphenyltelluride.The first step is the formation of a charge transfer complex, and the initial product of the oxidative addition is a "covalent" form of the tellurium(IV)compound. When the radical R is more stable, Ph2TeX2 may be the major tellurium(IV)product. The reaction of RTeNa (R=p-EtOC6H4, Ph) with organic dihalides X2(CH2)n (n=1,2,3,4) affords telluronium salts (n=3,4; X=Cl, Br) the nature of which is discussed.For n=l (X=Br, I)the products are formulated as charge transfer complexes of stoichiometry (RTe)2(CH2).CH2X2• For n=2, elimination of ditelluride occurs with the formation of an alkene. Some 125’Te Mõssbauer data are discussed and it is suggested that the unusually low value of 6 (7.58 mm.s-1 ) for  p-EtO.C6H4.Te)2(cH2)cH2Br2 relates to removal of 5's electronsfrom the spare pair orbltal via the charge transfer interaction. 125Te Mossbauer data for (p-EtO.C6H4)Te(CH2)4Br are typical of a tellurium (IV) compound and in particular ∇ is in the expected range for a telluronium salt. The product of the reaction of Na Te (C6H4.OEt), with 1,3-dibromopropane is, from the Mössbauer data, also a telluronium salt.