Reatores UASB em dois estágios seguidos de lodos ativados em batelada para o tratamento de águas residuárias do beneficiamento de café por via úmida

Pós-graduação em Microbiologia Agropecuária - FCAV

Desempenho de sistema composto por reatores anaeróbios em série seguido de filtro biológico percolador no tratamento de águas residuárias de suinocultura

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação do desempenho de um reator anaeróbio compartimentado no tratamento de esgoto doméstico

Pós-graduação em Engenharia Civil - FEIS

Estudo da fragilização ao revenido em aço liga de 2,25CR-1MO através do ensaio de indentificação instrumentada

2,25Cr-1Mo alloy steels are widely used in petrochemical plant equipments working in high temperature conditions because of their good mechanical proprieties in these conditions. Although, when exposed for a long time at high temperature, in the rage of 343 °C to 593 °C, may present the temper embrittlement phenomenon. The component named stripper of assembly converter of fluid catalytic cracking unit (UFCC) of studied plant is manufactured using this material, which is subject to temper embrittlement. The phenomenon of temper embrittlement refers to progressive lose of toughness, making the material brittle. With embrittlement, equipaments manufactured with this material are under risks to suffer brittle fracture in the cool down and start-up situations of them, which can cause catastrophic failures. By this reason, this research studies presence of temper ebrittlement phenomenon on this material. To verify the toughness of the material is conventionally used charpy V-notch test. However, this test requires the removing of samples of the material to make specimens. This fact becomes critical when talk about structural components of an equipment. So, this research also studies a non-destructive test that can be executes in-situ, known as instrumented indentation, as an alternative detection of the phenomenon at the component stripper, by comparative of the mechanical proprieties obtained by conventional tests in similar samples

The influence of handrim design on the contact forces on hands'surface: a preliminary study

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Water sorption of CH3- and CF3-Bis-GMA based resins with additives

Objectives: To evaluate the effect of additives on the water sorption characteristics of Bis-GMA based copolymers and composites containing TEGDMA, CH(3)Bis-GMA or CF(3)Bis-GMA. Material and methods: Fifteen experimental copolymers and corresponding composites were prepared combining Bis-GMA and TEGDMA, CH(3)Bis-GMA or CF(3)Bis-GMA, with aldehyde or diketone (24 and 32 mol%) totaling 30 groups. For composites, barium aluminosilicate glass and pyrogenic silica was added to comonomer mixtures. Photopolymerization was effected by 0.2 wt% each of camphorquinone and N,N-dimethyl-p-toluidine. Specimen densities in dry and water saturated conditions were obtained by Archimedes' method. Water sorption and desorption were evaluated in a desorption-sorption-desorption cycle. Water uptake (%WU), water desorption (%WD), equilibrium solubility (ES; mu g/mm(3)), swelling (f) and volume increase (%V) were calculated using appropriate equations. Results: All resins with additives had increased %WU and ES. TEGDMA-containing systems presented higher %WU, %WD, ES, f and %V values, followed by resins based on CH(3)Bis-GMA and CF(3)Bis-GMA. Conclusions: Aldehyde and diketone led to increases in the water sorption characteristics of experimental resins.

Properties of dental resins submitted to pH catalysed hydrolysis

Objectives: This study evaluated the surface microhardness (SM) and roughness (SR) alterations of dental resins submitted to pH catalysed degradation regimens. Methods: Thirty discs of each TPH Spectrum (Dentsply), Z100 (3M-ESPE), or an unfilled experimental bis-GMA/TEGDMA resin were fabricated, totaling 90 specimens. Each specimen was polymerized for 40 s, finished, polished, and individually stored in deionized water at 37 degrees C for 7 days. Specimens were randomly assigned to the following pH solutions: 1.0, 6.9 or 13, and for SM or SR evaluations (n = 5). Baseline Knoop-hardness of each specimen was obtained by the arithmetic mean of five random micro-indentations. For SR, mean baseline values were obtained by five random surface tracings (R-a). Specimens were then soaked in one of the following storage media at 37 degrees C: (1) 0.1 M, pH 1.0 HCl, (2) 0.1 N, pH 13.0 NaOCl, and (3) deionized water (pH 6.9). Solutions were replaced daily. Repeated SM and SR measurements were performed at the 3-, 7- and 14-day storage time intervals. For each test and resin, data were analysed by two-way ANOVA followed by Tukey's test (alpha = 0.05). Results: There was significant decrease in SM and increase in SR values of composites after storage in alkaline medium. TPH and Z100 presented similar behaviour for SM and SR after immersion in the different media, whereas unfilled resin values showed no significant change. Conclusion: Hydrolytic degradation of resin composites seems to begin with the silanized inorganic particles and therefore depend on their composition. Significance: To accelerate composite hydrolysis and produce quick in vitro microstructural damage, alkaline medium appears to be more suitable than acidic medium. Contemporary resin composite properties seem to withstand neutral and acidic oral environments tolerably well. (C) 2012 Elsevier Ltd. All rights reserved.

Microcollinearity between autopolyploid sugarcane and diploid sorghum genomes

Abstract Background Sugarcane (Saccharum spp.) has become an increasingly important crop for its leading role in biofuel production. The high sugar content species S. officinarum is an octoploid without known diploid or tetraploid progenitors. Commercial sugarcane cultivars are hybrids between S. officinarum and wild species S. spontaneum with ploidy at ~12×. The complex autopolyploid sugarcane genome has not been characterized at the DNA sequence level. Results The microsynteny between sugarcane and sorghum was assessed by comparing 454 pyrosequences of 20 sugarcane bacterial artificial chromosomes (BACs) with sorghum sequences. These 20 BACs were selected by hybridization of 1961 single copy sorghum overgo probes to the sugarcane BAC library with one sugarcane BAC corresponding to each of the 20 sorghum chromosome arms. The genic regions of the sugarcane BACs shared an average of 95.2% sequence identity with sorghum, and the sorghum genome was used as a template to order sequence contigs covering 78.2% of the 20 BAC sequences. About 53.1% of the sugarcane BAC sequences are aligned with sorghum sequence. The unaligned regions contain non-coding and repetitive sequences. Within the aligned sequences, 209 genes were annotated in sugarcane and 202 in sorghum. Seventeen genes appeared to be sugarcane-specific and all validated by sugarcane ESTs, while 12 appeared sorghum-specific but only one validated by sorghum ESTs. Twelve of the 17 sugarcane-specific genes have no match in the non-redundant protein database in GenBank, perhaps encoding proteins for sugarcane-specific processes. The sorghum orthologous regions appeared to have expanded relative to sugarcane, mostly by the increase of retrotransposons. Conclusions The sugarcane and sorghum genomes are mostly collinear in the genic regions, and the sorghum genome can be used as a template for assembling much of the genic DNA of the autopolyploid sugarcane genome. The comparable gene density between sugarcane BACs and corresponding sorghum sequences defied the notion that polyploidy species might have faster pace of gene loss due to the redundancy of multiple alleles at each locus.

Design methodologies of microwawe integrated circuits for satellite telecommunications

The running innovation processes of the microwave transistor technologies, used in the implementation of microwave circuits, have to be supported by the study and development of proper design methodologies which, depending on the applications, will fully exploit the technology potentialities. After the choice of the technology to be used in the particular application, the circuit designer has few degrees of freedom when carrying out his design; in the most cases, due to the technological constrains, all the foundries develop and provide customized processes optimized for a specific performance such as power, low-noise, linearity, broadband etc. For these reasons circuit design is always a “compromise”, an investigation for the best solution to reach a trade off between the desired performances. This approach becomes crucial in the design of microwave systems to be used in satellite applications; the tight space constraints impose to reach the best performances under proper electrical and thermal de-rated conditions, respect to the maximum ratings provided by the used technology, in order to ensure adequate levels of reliability. In particular this work is about one of the most critical components in the front-end of a satellite antenna, the High Power Amplifier (HPA). The HPA is the main power dissipation source and so the element which mostly engrave on space, weight and cost of telecommunication apparatus; it is clear from the above reasons that design strategies addressing optimization of power density, efficiency and reliability are of major concern. Many transactions and publications demonstrate different methods for the design of power amplifiers, highlighting the availability to obtain very good levels of output power, efficiency and gain. Starting from existing knowledge, the target of the research activities summarized in this dissertation was to develop a design methodology capable optimize power amplifier performances complying all the constraints imposed by the space applications, tacking into account the thermal behaviour in the same manner of the power and the efficiency. After a reminder of the existing theories about the power amplifier design, in the first section of this work, the effectiveness of the methodology based on the accurate control of the dynamic Load Line and her shaping will be described, explaining all steps in the design of two different kinds of high power amplifiers. Considering the trade-off between the main performances and reliability issues as the target of the design activity, we will demonstrate that the expected results could be obtained working on the characteristics of the Load Line at the intrinsic terminals of the selected active device. The methodology proposed in this first part is based on the assumption that designer has the availability of an accurate electrical model of the device; the variety of publications about this argument demonstrates that it is so difficult to carry out a CAD model capable to taking into account all the non-ideal phenomena which occur when the amplifier operates at such high frequency and power levels. For that, especially for the emerging technology of Gallium Nitride (GaN), in the second section a new approach for power amplifier design will be described, basing on the experimental characterization of the intrinsic Load Line by means of a low frequency high power measurements bench. Thanks to the possibility to develop my Ph.D. in an academic spin-off, MEC – Microwave Electronics for Communications, the results of this activity has been applied to important research programs requested by space agencies, with the aim support the technological transfer from universities to industrial world and to promote a science-based entrepreneurship. For these reasons the proposed design methodology will be explained basing on many experimental results.

Il sindacato della Corte di cassazione sul travisamento della prova

Sect. 606, par. 1, e), as modified by Law 46, enacted on Februray 20th, 2006 introduced the chance to appeal to the Court of cassation in case of inconsistent reasoning and extended control on its existence and on other flaws and lack of obvious logic over the text of the contested decision, namely “to other acts the process specified in the grounds of burden”. The renewed provision seems to properly reappoint the “distortion of the evidence”, i.e. the omitted or distorted evidence that could be relevant and conclusive one, in the peculiar context of the grounds' vice. After a general review of the obligation to state reasons for judicial decisions, we analyze the innovative status of the vice of “distortion of evidence” and the conditions and the limits - defined by the law - within we can contest a resolution for illegitimacy. Then, we outline the systematic spin-off brought by the new form of sect. 606, par. 1, e) on some institutions in the code of criminal procedure. Finally, we make the role of the Court of cassation clear in the modern criminal trial, since the 2006 reform gave no definite answer on this fundamental aspect of the question.

"Luxio": l'innovazione nella pubblica illuminazione. Redazione del business plan per il lancio del nuovo prodotto.

Il Business Plan è un importante strumento ai fini della pianificazione strategica delle imprese, siano esse già avviate o in fase di start up. Le varie funzioni che esso svolge, sono di natura sia interna all’impresa, evidenziando all’alta direzione le conseguenze economiche e finanziarie di determinate decisioni, che esterna all’impresa, volta ad illustrare il progetto ai vari stake-holders. L’obiettivo del presente lavoro è di offrire un contributo a coloro cui compete il compito di redigere un Business Plan, in ordine ai contenuti, ai criteri e agli strumenti logici e tecnici per la sua redazione, avendo comunque ben presente che ogni progetto imprenditoriale si caratterizza con peculiarità proprie. Pertanto, nella prima parte del presente lavoro, dopo un illustrazione delle molteplici funzioni del Business Plan, verranno fornite precise e concrete indicazioni su come deve essere articolato un buon piano d’impresa, soffermandosi in particolare sui contenuti dei vari argomenti che occorre esaminare all’interno dello stesso. Nella seconda parte verrà descritta la nascita e la struttura della Rebernig Supervisioni S.r.l., azienda con la quale ho collaborato per la redazione del presente lavoro. Nella terza parte, verrà invece sviluppato un vero e proprio Business Plan, riferito ad un caso con concreto, quello dell’azienda Rebernig Supervisioni S.r.l., per il lancio di un nuovo prodotto sul mercato dell’illuminazione. Un sentito ringraziamento al management della Rebernig Supervisioni S.r.l. per la collaborazione prestata e per il tempo da loro dedicato, fornendo in tal modo un importante contributo ai fini della redazione del presente lavoro.

Nano-Power Integrated Circuits for Energy Harvesting

The energy harvesting research field has grown considerably in the last decade due to increasing interests in energy autonomous sensing systems, which require smart and efficient interfaces for extracting power from energy source and power management (PM) circuits. This thesis investigates the design trade-offs for minimizing the intrinsic power of PM circuits, in order to allow operation with very weak energy sources. For validation purposes, three different integrated power converter and PM circuits for energy harvesting applications are presented. They have been designed for nano-power operations and single-source converters can operate with input power lower than 1 μW. The first IC is a buck-boost converter for piezoelectric transducers (PZ) implementing Synchronous Electrical Charge Extraction (SECE), a non-linear energy extraction technique. Moreover, Residual Charge Inversion technique is exploited for extracting energy from PZ with weak and irregular excitations (i.e. lower voltage), and the implemented PM policy, named Two-Way Energy Storage, considerably reduces the start-up time of the converter, improving the overall conversion efficiency. The second proposed IC is a general-purpose buck-boost converter for low-voltage DC energy sources, up to 2.5 V. An ultra-low-power MPPT circuit has been designed in order to track variations of source power. Furthermore, a capacitive boost circuit has been included, allowing the converter start-up from a source voltage VDC0 = 223 mV. A nano-power programmable linear regulator is also included in order to provide a stable voltage to the load. The third IC implements an heterogeneous multisource buck-boost converter. It provides up to 9 independent input channels, of which 5 are specific for PZ (with SECE) and 4 for DC energy sources with MPPT. The inductor is shared among channels and an arbiter, designed with asynchronous logic to reduce the energy consumption, avoids simultaneous access to the buck-boost core, with a dynamic schedule based on source priority.

Microfluidic microbial fuel cell fabrication and rapid screening of electrochemically microbes

The demand for novel renewable energy sources, together with the new findings on bacterial electron transport mechanisms and the progress in microbial fuel cell design, have raised a noticeable interest in microbial power generation. Microbial fuel cell (MFC) is an electrochemical device that converts organic substrates into electricity via catalytic conversion by microorganism. It has represented a continuously growing research field during the past few years. The great advantage of this device is the direct conversion of the substrate into electricity and in the future, MFC may be linked to municipal waste streams or sources of agricultural and animal waste, providing a sustainable system for waste treatment and energy production. However, these novel green technologies have not yet been used for practical applications due to their low power outputs and challenges associated with scale-up, so in-depth studies are highly necessary to significantly improve and optimize the device working conditions. For the time being, the micro-scale MFCs show great potential in the rapid screening of electrochemically active microbes. This thesis presents how it will be possible to optimize the properties and design of the micro-size microbial fuel cell for maximum efficiency by understanding the MFC system. So it will involve designing, building and testing a miniature microbial fuel cell using a new species of microorganisms that promises high efficiency and long lifetime. The new device offer unique advantages of fast start-up, high sensitivity and superior microfluidic control over the measured microenvironment, which makes them good candidates for rapid screening of electrode materials, bacterial strains and growth media. It will be made in the Centre of Hybrid Biodevices (Faculty of Physical Sciences and Engineering, University of Southampton) from polymer materials like PDMS. The eventual aim is to develop a system with the optimum combination of microorganism, ion exchange membrane and growth medium. After fabricating the cell, different bacteria and plankton species will be grown in the device and the microbial fuel cell characterized for open circuit voltage and power. It will also use photo-sensitive organisms and characterize the power produced by the device in response to optical illumination.

Ago e filo 3.0: quali opportunità di business per l'artigianato locale con l'evoluzione dei social? C'è ancora spazio e visibilità per loro?

Con l’evoluzione dei social network e degli strumenti del 2.0 (blog, wiki, forum), internet si avvia verso nuove forme di business cui artigiani e pmi possono sfruttare per nuove opportunità, unendo social network e e-commerce e capire come si è evoluto il processo di creazione e finanziamento di un prodotto. La tesi è un viaggio per scoprire quali sono queste nuove opportunità per chi pratica artigianato a livello locale, e come è cambiata la figura stessa dell’artigiano, tra questi un nuovo movimento chiamato makers, che sfruttano i nuovi strumenti, tra cui anche mezzi rivoluzionari come la stampante 3D ora accessibile a tutti per creare oggetti e nuove idee. Sarà necessario capire quali sono le vetrine online dove e come poter vendere i nostri prodotti e profilare attraverso una segmentazione l’utente medio che già utilizza il social-commerce. In seguito si tratta il caso empirico di una start-up italiana, Blomming, una dei primi a differenziarsi dagli altri marketplace più famosi come contenitore adatto ad artigiani, ma non solo. Si seguiranno le varie fasi di crescita da un’idea, introduzione nel mercato fino alla direzione a cui si sta avviando con le ultime novità effettuando un’analisi dei rischi. Infine per capire tendenze e storie di chi sta già usando queste piattaforme è stato necessario fare un profilo dell’artigiano fai-da-te medio intervistando, e successivamente creando grafici, 100 artigiani che già vendono online.

L'interpretazione a distanza: presentazione della piattaforma veasyt live!, case study italiano e proposta di seminario.

Il presente elaborato offre una panoramica generale del Remote Interpreting (RI) con l'obiettivo di strutturare un ipotetico seminario da tenere alla SLLTI (Scuola di Lingue e Letterature, Traduzione e Interpretazione, ex SSLMIT) di Forlì, in collaborazione con l'azienda VEASYT, spin-off dell’università Ca' Foscari di Venezia, per introdurre l'argomento agli studenti del corso di laurea in Interpretazione di Conferenza. A tal scopo la tesi è stata suddivisa in dieci capitoli, ognuno dei quali analizza una sfaccettatura dell'interpretazione da remoto; la prima parte verte sull'evoluzione storica delle nuove tecnologie nel mondo dell'interpretariato, con particolare attenzione all'introduzione degli impianti per l'interpretazione simultanea e delle Tecnologie dell'Informazione e della Comunicazione (TIC); si presentano inoltre i principali tipi di interpretazione a distanza, seguendo la loro comparsa in ordine cronologico, e i dispositivi necessari per effettuare una sessione di video-interpretazione. Nella seconda parte si descrivono alcuni ambiti di applicazione del RI (RI per non udenti, in ambito giuridico, in ambito medico-sanitario) e si illustra la situazione a livello mondiale passando in rassegna, a titolo di esempio, alcune aziende presenti in Australia, Stati Uniti, Germania, Austria e Gran Bretagna. Nella terza parte si presentano alcuni regolamenti e disposizioni raccomandati da associazioni di categoria e dalle istituzioni europee e si analizzano i principali vantaggi e svantaggi del RI. Nella quarta parte si mettono a confronto le caratteristiche e il tipo di formazione di un interprete che lavora in situ con quelle di un interprete che lavora a distanza, illustrando alcune strategie sviluppate dagli interpreti durante le sessioni di RI. L'ultima parte riguarda l'azienda VEASYT, la quale viene presentata come case study italiano, descrivendo la sua piattaforma per il servizio di interpretariato da remoto e la modalità di reclutamento degli interpreti. In conclusione si trova la proposta di seminario da tenere ipoteticamente alla SLLTI di Forlì, che viene articolata seguendo la successione dei capitoli precedenti.