SOLUBLE POLY-(O,M)-TOLUIDINE

The soluble poly-o-toluidine (POT) and poly-m-toluidine (PMT) have been success- fully prepared under controlled conditions of polymerization and post-treatment, and characterized by IR, VPO and elemental analysis. It is found that the soluble and insol- uble polymers obtained with two different methods (Ⅰ and Ⅱ) have the similar conduc- tivity and molecular chain structure. VPO measurement shows that the number average molecular weight (Mn) of soluble polymers is about 3000. The mole ratio o...

Highly soluble and stable recombinant holo-phycocyanin alpha subunit expressed in Escherichia coli

C-phycocyanin (Cpc) is one of the phycobiliproteins with highly fluorescent and various pharmacological activities Holo-Cpc-alpha Subunit (holo-CpcA) expressed in Escherichia colt resulted in low yield and tended to aggregate after purification in this Study, we constructed a new plasmid coding holo-CpcA fused with hexahistidine and maltose-binding protein tag, which designated as HMCpcA. to Improve Its Solubility and stability without the Impairment of its spectra anti fluorescent properties HMCpcA was significantly more stable over time and a wider range of pH as compared to holo-CpcA. In addition. both the solubility and yields of HMCpcA increase significantly We here provided an example to demonstrate that MBP could also Improve the stability of the protein it fused while it has been reported as a soluble fusion partner before. This novel fluorescent protein will facilitate the large-scale production and be potentially applicable for the development Of fluorescent probes, as well as antioxidant agents (C) 2009 Elsevier B V. All rights reserved

A remarkable synergic effect of water-soluble bimetallic catalyst in the hydrogenation of aromatic nitrocompounds

Hydrogenation of nitrobenzene can be catalyzed by the water-soluble catalyst PdCl2(TPPTS)(2) (TPPTS = tris(m-sulfonatophenyl)phosphine trisodium salt) under normal pressure at 65 degrees C in H2O/toluene biphasic solvent system. The exhibits higher catalytic activity and selectivity for the hydrogenation of aromatic nitrocompounds, compared with PdCl2(TPPTS)(2) or H2PtCl6 alone. The transmission electron micrographs demonstrate that the monometallic catalyst is composed of ultrafine palladium particles of almost uniform size while the particles of bimetallic catalyst are more widely distributed in size than those of the monometallic ones. (C) 1999 Elsevier Science B.V. All rights reserved.

Association of candidate genes with flowering time and water-soluble carbohydrate content in Lolium perenne (L.)

Sk?t, L., Humphreys, J., Humphreys, M. O., Thorogood, D., Gallagher, J. A., Sanderson, R., Armstead, I. P., Thomas, I. D. (2007). Association of candidate genes with flowering time and water-soluble carbohydrate content in Lolium perenne (L.). Genetics, 177 (1), 535-547. Sponsorship: BBSRC RAE2008

Application of mesoporous silica for the oral delivery of poorly water-soluble drugs

The objective of this thesis was to improve the dissolution rate of the poorly waters-soluble drug, fenofibrate by processing it with a high surface area carrier, mesoporous silica. The subsequent properties of the drug – silica composite were studied in terms of drug distribution within the silica matrix, solid state and release properties. Prior to commencing any experimental work, the properties of unprocessed mesoporous silica and fenofibrate were characterised (chapter 3), this allowed for comparison with the processed samples studied in later chapters. Fenofibrate was a highly stable, crystalline drug that did not adsorb moisture, even under long term accelerated storage conditions. It maintained its crystallinity even after SC-CO2 processing. Its dissolution rate was limited and dependent on the characteristics of the particular in vitro media studied. Mesoporous silica had a large surface area and mesopore volume and readily picked up moisture when stored under long term accelerated storage conditions (75% RH, 40 oC). It maintained its mesopore character after SC-CO2 processing. A variety of methods were employed to process fenofibrate with mesoporous silica including physical mixing, melt method, solvent impregnation and novel methods such as liquid and supercritical carbon dioxide (SC-CO2) (chapter 4). It was found that it was important to break down the fenofibrate particulate structure to a molecular state to enable drug molecules enter into the silica mesopores. While all processing methods led to some increase in fenofibrate release properties; the impregnation, liquid and SC-CO2 methods produced the most rapid release rates. SC-CO2 processing was further studied with a view to optimising the processing parameters to achieve the highest drug-loading efficiency possible (chapter 5). In this thesis, it was that SC-CO2 processing pressure had a bearing on drug-loading efficiency. Neither pressure, duration or depressurisation rate affected drug solid state or release properties. The amount of drug that could be loaded onto to the mesoporous silica successfully was also investigated at different ratios of drug mass to silica surface area under constant SC-CO2 conditions; as the drug – silica ratio increased, the drug-loading efficiency decreased, while there was no effect on drug solid state or release properties. The influence of the number of drug-loading steps was investigated (chapter 6) with a view to increasing the drug-loading efficiency. This multiple step approach did not yield an increase in drug-loading efficiency compared to the single step approach. It was also an objective in this chapter to understand how much drug could be loaded into silica mesopores; a method based on the known volume of the mesopores and true density of drug was investigated. However, this approach led to serious repercussions in terms of the subsequent solid state nature of the drug and its release performance; there was significant drug crystallinity and reduced release extent. The impact of in vitro release media on fenofibrate release was also studied (chapter 6). Here it was seen that media containing HCl led to reduced drug release over time compared to equivalent media not containing HCl. The key findings of this thesis are discussed in chapter 7 and included: 1. Drug – silica processing method strongly influenced drug distribution within the silica matrix, drug solid state and release. 2. The silica surface area and mesopore volume also influenced how much drug could be loaded. It was shown that SC-CO2 processing variables such as processing pressure (13.79 – 41.37 MPa), duration time (4 – 24 h) and depressurisation rate (rapid or controlled) did not influence the drug distribution within the SBA- 15 matrix, drug solid state form or release. Possible avenues of research to be considered going forward include the development and application of high resolution imaging techniques to visualise drug molecules within the silica mesopores. Also, the issues surrounding SBA-15 usage in a pharmaceutical manufacturing environment should be addressed.