Heavy vehicle suspensions : testing and analysis

Transport regulators consider that, with respect to pavement damage, heavy vehicles (HVs) are the riskiest vehicles on the road network. That HV suspension design contributes to road and bridge damage has been recognised for some decades. This thesis deals with some aspects of HV suspension characteristics, particularly (but not exclusively) air suspensions. This is in the areas of developing low-cost in-service heavy vehicle (HV) suspension testing, the effects of larger-than-industry-standard longitudinal air lines and the characteristics of on-board mass (OBM) systems for HVs. All these areas, whilst seemingly disparate, seek to inform the management of HVs, reduce of their impact on the network asset and/or provide a measurement mechanism for worn HV suspensions. A number of project management groups at the State and National level in Australia have been, and will be, presented with the results of the project that resulted in this thesis. This should serve to inform their activities applicable to this research. A number of HVs were tested for various characteristics. These tests were used to form a number of conclusions about HV suspension behaviours. Wheel forces from road test data were analysed. A “novel roughness” measure was developed and applied to the road test data to determine dynamic load sharing, amongst other research outcomes. Further, it was proposed that this approach could inform future development of pavement models incorporating roughness and peak wheel forces. Left/right variations in wheel forces and wheel force variations for different speeds were also presented. This led on to some conclusions regarding suspension and wheel force frequencies, their transmission to the pavement and repetitive wheel loads in the spatial domain. An improved method of determining dynamic load sharing was developed and presented. It used the correlation coefficient between two elements of a HV to determine dynamic load sharing. This was validated against a mature dynamic loadsharing metric, the dynamic load sharing coefficient (de Pont, 1997). This was the first time that the technique of measuring correlation between elements on a HV has been used for a test case vs. a control case for two different sized air lines. That dynamic load sharing was improved at the air springs was shown for the test case of the large longitudinal air lines. The statistically significant improvement in dynamic load sharing at the air springs from larger longitudinal air lines varied from approximately 30 percent to 80 percent. Dynamic load sharing at the wheels was improved only for low air line flow events for the test case of larger longitudinal air lines. Statistically significant improvements to some suspension metrics across the range of test speeds and “novel roughness” values were evident from the use of larger longitudinal air lines, but these were not uniform. Of note were improvements to suspension metrics involving peak dynamic forces ranging from below the error margin to approximately 24 percent. Abstract models of HV suspensions were developed from the results of some of the tests. Those models were used to propose further development of, and future directions of research into, further gains in HV dynamic load sharing. This was from alterations to currently available damping characteristics combined with implementation of large longitudinal air lines. In-service testing of HV suspensions was found to be possible within a documented range from below the error margin to an error of approximately 16 percent. These results were in comparison with either the manufacturer’s certified data or test results replicating the Australian standard for “road-friendly” HV suspensions, Vehicle Standards Bulletin 11. OBM accuracy testing and development of tamper evidence from OBM data were detailed for over 2000 individual data points across twelve test and control OBM systems from eight suppliers installed on eleven HVs. The results indicated that 95 percent of contemporary OBM systems available in Australia are accurate to +/- 500 kg. The total variation in OBM linearity, after three outliers in the data were removed, was 0.5 percent. A tamper indicator and other OBM metrics that could be used by jurisdictions to determine tamper events were developed and documented. That OBM systems could be used as one vector for in-service testing of HV suspensions was one of a number of synergies between the seemingly disparate streams of this project.

Traffic Simulation for Proactive Traffic Management

Presentation on intelligent transport systems profects and traffic engineering,simulation and modelling by QUT researchers

Modeling crash outcome probabilities at rural intersections: Application of hierarchical binomial logistic models

It is important to examine the nature of the relationships between roadway, environmental, and traffic factors and motor vehicle crashes, with the aim to improve the collective understanding of causal mechanisms involved in crashes and to better predict their occurrence. Statistical models of motor vehicle crashes are one path of inquiry often used to gain these initial insights. Recent efforts have focused on the estimation of negative binomial and Poisson regression models (and related deviants) due to their relatively good fit to crash data. Of course analysts constantly seek methods that offer greater consistency with the data generating mechanism (motor vehicle crashes in this case), provide better statistical fit, and provide insight into data structure that was previously unavailable. One such opportunity exists with some types of crash data, in particular crash-level data that are collected across roadway segments, intersections, etc. It is argued in this paper that some crash data possess hierarchical structure that has not routinely been exploited. This paper describes the application of binomial multilevel models of crash types using 548 motor vehicle crashes collected from 91 two-lane rural intersections in the state of Georgia. Crash prediction models are estimated for angle, rear-end, and sideswipe (both same direction and opposite direction) crashes. The contributions of the paper are the realization of hierarchical data structure and the application of a theoretically appealing and suitable analysis approach for multilevel data, yielding insights into intersection-related crashes by crash type.

Modeling crash types: New insights into the effects of covariates on crashes at rural intersections

Many studies focused on the development of crash prediction models have resulted in aggregate crash prediction models to quantify the safety effects of geometric, traffic, and environmental factors on the expected number of total, fatal, injury, and/or property damage crashes at specific locations. Crash prediction models focused on predicting different crash types, however, have rarely been developed. Crash type models are useful for at least three reasons. The first is motivated by the need to identify sites that are high risk with respect to specific crash types but that may not be revealed through crash totals. Second, countermeasures are likely to affect only a subset of all crashes—usually called target crashes—and so examination of crash types will lead to improved ability to identify effective countermeasures. Finally, there is a priori reason to believe that different crash types (e.g., rear-end, angle, etc.) are associated with road geometry, the environment, and traffic variables in different ways and as a result justify the estimation of individual predictive models. The objectives of this paper are to (1) demonstrate that different crash types are associated to predictor variables in different ways (as theorized) and (2) show that estimation of crash type models may lead to greater insights regarding crash occurrence and countermeasure effectiveness. This paper first describes the estimation results of crash prediction models for angle, head-on, rear-end, sideswipe (same direction and opposite direction), and pedestrian-involved crash types. Serving as a basis for comparison, a crash prediction model is estimated for total crashes. Based on 837 motor vehicle crashes collected on two-lane rural intersections in the state of Georgia, six prediction models are estimated resulting in two Poisson (P) models and four NB (NB) models. The analysis reveals that factors such as the annual average daily traffic, the presence of turning lanes, and the number of driveways have a positive association with each type of crash, whereas median widths and the presence of lighting are negatively associated. For the best fitting models covariates are related to crash types in different ways, suggesting that crash types are associated with different precrash conditions and that modeling total crash frequency may not be helpful for identifying specific countermeasures.

Fusing curricula : science, technology and ICT

Curriculum demands continue to increase on school education systems with teachers at the forefront of implementing syllabus requirements. Education is reported frequently as a solution to most societal problems and, as a result of the world’s information explosion, teachers are expected to cover more and more within teaching programs. How can teachers combine subjects in order to capitalise on the competing educational agendas within school timeframes? Fusing curricula requires the bonding of standards from two or more syllabuses. Both technology and ICT complement the learning of science. This study analyses selected examples of preservice teachers’ overviews for fusing science, technology and ICT. These program overviews focused on primary students and the achievement of two standards (one from science and one from either technology or ICT). These primary preservice teachers’ fused-curricula overviews included scientific concepts and related technology and/or ICT skills and knowledge. Findings indicated a range of innovative curriculum plans for teaching primary science through technology and ICT, demonstrating that these subjects can form cohesive links towards achieving the respective learning standards. Teachers can work more astutely by fusing curricula; however further professional development may be required to advance thinking about these processes. Bonding subjects through their learning standards can extend beyond previous integration or thematic work where standards may not have been assessed. Education systems need to articulate through syllabus documents how effective fusing of curricula can be achieved. It appears that education is a key avenue for addressing societal needs, problems and issues. Education is promoted as a universal solution, which has resulted in curriculum overload (Dare, Durand, Moeller, & Washington, 1997; Vinson, 2001). Societal and curriculum demands have placed added pressure on teachers with many extenuating education issues increasing teachers’ workloads (Mobilise for Public Education, 2002). For example, as Australia has weather conducive for outdoor activities, social problems and issues arise that are reported through the media calling for action; consequently schools have been involved in swimming programs, road and bicycle safety programs, and a wide range of activities that had been considered a parental responsibility in the past. Teachers are expected to plan, implement and assess these extra-curricula activities within their already overcrowded timetables. At the same stage, key learning areas (KLAs) such as science and technology are mandatory requirements within all Australian education systems. These systems have syllabuses outlining levels of content and the anticipated learning outcomes (also known as standards, essential learnings, and frameworks). Time allocated for teaching science in obviously an issue. In 2001, it was estimated that on average the time spent in teaching science in Australian Primary Schools was almost an hour per week (Goodrum, Hackling, & Rennie, 2001). More recently, a study undertaken in the U.S. reported a similar finding. More than 80% of the teachers in K-5 classrooms spent less than an hour teaching science (Dorph, Goldstein, Lee, et al., 2007). More importantly, 16% did not spend teaching science in their classrooms. Teachers need to learn to work smarter by optimising the use of their in-class time. Integration is proposed as one of the ways to address the issue of curriculum overload (Venville & Dawson, 2005; Vogler, 2003). Even though there may be a lack of definition for integration (Hurley, 2001), curriculum integration aims at covering key concepts in two or more subject areas within the same lesson (Buxton & Whatley, 2002). This implies covering the curriculum in less time than if the subjects were taught separately; therefore teachers should have more time to cover other educational issues. Expectedly, the reality can be decidedly different (e.g., Brophy & Alleman, 1991; Venville & Dawson, 2005). Nevertheless, teachers report that students expand their knowledge and skills as a result of subject integration (James, Lamb, Householder, & Bailey, 2000). There seems to be considerable value for integrating science with other KLAs besides aiming to address teaching workloads. Over two decades ago, Cohen and Staley (1982) claimed that integration can bring a subject into the primary curriculum that may be otherwise left out. Integrating science education aims to develop a more holistic perspective. Indeed, life is not neat components of stand-alone subjects; life integrates subject content in numerous ways, and curriculum integration can assist students to make these real-life connections (Burnett & Wichman, 1997). Science integration can provide the scope for real-life learning and the possibility of targeting students’ learning styles more effectively by providing more than one perspective (Hudson & Hudson, 2001). To illustrate, technology is essential to science education (Blueford & Rosenbloom, 2003; Board of Studies, 1999; Penick, 2002), and constructing technology immediately evokes a social purpose for such construction (Marker, 1992). For example, building a model windmill requires science and technology (Zubrowski, 2002) but has a key focus on sustainability and the social sciences. Science has the potential to be integrated with all KLAs (e.g., Cohen & Staley, 1982; Dobbs, 1995; James et al., 2000). Yet, “integration” appears to be a confusing term. Integration has an educational meaning focused on special education students being assimilated into mainstream classrooms. The word integration was used in the late seventies and generally focused around thematic approaches for teaching. For instance, a science theme about flight only has to have a student drawing a picture of plane to show integration; it did not connect the anticipated outcomes from science and art. The term “fusing curricula” presents a seamless bonding between two subjects; hence standards (or outcomes) need to be linked from both subjects. This also goes beyond just embedding one subject within another. Embedding implies that one subject is dominant, while fusing curricula proposes an equal mix of learning within both subject areas. Primary education in Queensland has eight KLAs, each with its established content and each with a proposed structure for levels of learning. Primary teachers attempt to cover these syllabus requirements across the eight KLAs in less than five hours a day, and between many of the extra-curricula activities occurring throughout a school year (e.g., Easter activities, Education Week, concerts, excursions, performances). In Australia, education systems have developed standards for all KLAs (e.g., Education Queensland, NSW Department of Education and Training, Victorian Education) usually designated by a code. In the late 1990’s (in Queensland), “core learning outcomes” for strands across all KLA’s. For example, LL2.1 for the Queensland Education science syllabus means Life and Living at Level 2 standard number 1. Thus, a teacher’s planning requires the inclusion of standards as indicated by the presiding syllabus. More recently, the core learning outcomes were replaced by “essential learnings”. They specify “what students should be taught and what is important for students to have opportunities to know, understand and be able to do” (Queensland Studies Authority, 2009, para. 1). Fusing science education with other KLAs may facilitate more efficient use of time and resources; however this type of planning needs to combine standards from two syllabuses. To further assist in facilitating sound pedagogical practices, there are models proposed for learning science, technology and other KLAs such as Bloom’s Taxonomy (Bloom, 1956), Productive Pedagogies (Education Queensland, 2004), de Bono’s Six Hats (de Bono, 1985), and Gardner’s Multiple Intelligences (Gardner, 1999) that imply, warrant, or necessitate fused curricula. Bybee’s 5 Es, for example, has five levels of learning (engage, explore, explain, elaborate, and evaluate; Bybee, 1997) can have the potential for fusing science and ICT standards.

Who are the real “first offenders”?

Drink driving causes more fatal crashes than any other single factor on Australian roads, with a third of crashes having alcohol as a contributing factor. In recent years there has been a plateau in the numbers of drink drivers apprehended by RBT, and around 12% of the general population in self report surveys admit to drinking and driving. There is limited information about the first offender group, particularly the subgroup of these offenders who admit to prior drink driving, the offence therefore being the “first time caught”. This research focuses on the differences between those who report drink driving prior to apprehension for the offence and those who don’t. Methods: 201 first time drink driving offenders were interviewed at the time of their court appearance. Information was collected on socio-demographic variables, driving behaviour, method of apprehension, offence information, alcohol use and self reported previous drink driving. Results: 78% of respondents reported that they had driven over the legal alcohol limit in the 6 months prior to the offence. Analyses revealed that those offenders who had driven over the limit previously without being caught were more likely to be younger and have an issue with risky drinking. When all variables were taken into account in a multivariate model using logistic regression, only risky drinking emerged as significantly related to past drink driving. High risk drinkers were 4.8 times more likely to report having driven over the limit without being apprehended in the previous 6 months. Conclusion: The majority of first offenders are those who are “first time apprehended” rather than “first time drink drivers”. Having an understanding of the differences between these groups may alter the focus of educational or rehabilitation countermeasures. This research is part of a larger project aiming to target first time apprehended offenders for tailored intervention.

Profiling the offence patterns of disqualified drink drivers in Queensland, Australia.

While unlicensed driving does not play a direct causative role in road crashes, it represents a major problem for road safety. A particular subgroup of concern is those offenders who continue to drive after having their licence disqualified for drink driving. Surveys of disqualified drivers suggest that driving among this group is relatively common. Method This paper reports findings from an analysis of the driving records of over 545,000 Queensland drivers who experienced a licence sanction between January 2003 and December 2008. The sample included drivers who were disqualified by a court (e.g., for drink driving); those who licence had been suspended administratively (e.g., for accumulation of demerit points); and those who were placed on a restricted licence. Results Overall, 95,461 of the drivers in the sample were disqualified from driving for a drink driving offence. During the period, these drivers were issued with a total of 2,644,619 traffic infringements with approximately 12% (n = 8, 095) convicted of a further drink driving offence while disqualified. Other traffic offences detected during this period including unlicensed driving (18%), driving an unregistered vehicle (27%), speeding (21%), dangerous driving (36%), mobile phone use (35%), non-restraint use (32%), and other moving violation (23%). Offending behaviour was more common among men than women. Conclusions While licence disqualification has previously been shown to be a relatively effective sanction for managing the behaviour of drink driving offenders, the results of the current study highlight that it is a far from perfect tool since many offenders continue to commit both drink driving and other traffic offences while disqualified. As such, this study highlights the ongoing need to enhance the detection of disqualified and unlicensed driving in order to deter this behaviour.

The Culture of Older Women’s Drinking in Australia

The purpose of this investigation was to undertake pilot research to develop an understanding of the current culture of older Australian women’s (35-50 years) drinking behaviour from a uniquely female perspective. Methods Two separate focus group interviews were undertaken with women (N = 11) aged between 35 and 50 years living in South-East Queensland, Australia. Women were asked to openly discuss how and why they drink alcohol (ie., their regular drinking behaviour), how this has changed over time, and the attitudes and values that influence their behaviour. Results Participants reported that their consumption of alcohol was more regulated and controlled and although some women drank more frequently, the quantity consumed at each drinking occasion had decreased significantly. Occasional consumption of large amounts of alcohol tended to be the result of ‘incidental drinking’ as opposed to ‘determined drinking’. The reasons for alcohol consumption were found to be internal as well as social. Internal reasons included stress relief, increased relaxation and self reward. Further, alcohol was used as a social lubricant. This cohort also reported being influenced by the drinking patterns of their partners. Social group matching was however found to have a negative impact on alcohol consumption as social groups most commonly endorsed lesser levels of intoxication. Further, the women reported that they were of an age in which they felt excessive drinking to be ‘undignified’. Personal reasons such as vocational and family responsibilities further modified the levels of consumption for individual women. Finally, it was reported that perceived health risks that can result from excessive and/or repetitive drinking led to a decreased in consumption. Conclusion It is proposed that the findings of this investigation could be used to improve current knowledge regarding more mature women’s drinking culture, associated risks and risk prevention strategies.

Beyond sanctions : is there a need to treat first-time offenders?

Aims: Driving Under the Influence (DUI) enforcement can be a broad screening mechanism for alcohol and other drug problems. The current response to DUI is focused on using mechanical means to prevent inebriated persons from driving, with little attention the underlying substance abuse problems. ---------- Methods: This is a secondary analysis of an administrative dataset of over 345,000 individuals who entered Texas substance abuse treatment between 2005 and 2008. Of these, 36,372 were either on DUI probation, referred to treatment by probation, or had a DUI arrest in the past year. The DUI offenders were compared on demographic characteristics, substance use patterns, and levels of impairment with those who were not DUI offenders and first DUI offenders were compared with those with more than one past-year offense. T tests and chi square tests were used to determine significance. ---------- Results: DUI offenders were more likely to be employed, to have a problem with alcohol, to report more past-year arrests for any offense, to be older, and to have used alcohol and drugs longer than the non-DUI clients who reported higher ASI scores and were more likely to use daily. Those with one past-year DUI arrest were more likely to have problems with drugs other than alcohol and were less impaired than those with two or more arrests based on their ASI scores and daily use. Non-DUI clients reported higher levels of mood disorders than DUIs but there was no difference in their diagnosis of anxiety. Similar findings were found between those with one or multiple DUI arrests. ----------Conclusion: Although first-time DUIs were not as impaired as non-DUI clients, their levels of impairment were sufficient to cause treatment. Screening and brief intervention at arrest for all DUI offenders and treatment in combination with abstinence monitoring could decrease future recidivism.

Trends in impaired driving in Australia in 2010 : a status report

This paper reviews the status of alcohol, drugs and traffic safety in Australia, with particular emphasis on developments in the period 2008-2010. Australian jurisdictions have made impressive improvements in road safety since the early 1970s. Enforcement and public education campaigns that specifically target drink driving have been successful, with resultant long-term reduction in alcohol-related fatalities. There is a high level of community disapproval of drink driving and strong support for countermeasures. Many best-practice countermeasures targeting impaired driving are in place, including general prevention/ deterrence programs such as random breath testing (RBT), random roadside drug testing legal alcohol limits, responsible service of alcohol programs, public education and advertising campaigns and designated driver programs, and offender management programs such as driver licensing penalties and fines, alcohol ignition interlocks and vehicle impoundment for high risk drink drivers, and offender education programs. There continue to be enhancements occurring, particularly in the areas of drug-impaired driving and offender management, but also in addressing the fundamental policy and legislative framework to address impaired driving (e.g., a current national debate about lowering the permissible blood alcohol for all drivers from 0.05 to 0.02 or 0.00 gm/100 ml BAC). However, there are major challenges that may be impacting on programs targeting impaired driving, including the rapid development of a binge drinking culture among young Australians, the extension of trading hours of licensed premises, continued problems with secondary supply of alcohol to minors, and increases in the marketing of alcopops and ready-to-drink spirit-based beverages. This paper addresses the question: Are impaired driving countermeasures in Australia continuing to achieve reductions in road traumas and rates of offending, or are they plateauing? If they are plateauing, is this due to declining effectiveness of countermeasures or the need to ‘hold the line’ against societal influences encouraging impaired driving?

Should we be concerned about alcohol in bicycle crashes?

This paper sets out to examine from published literature and crash data analyses whether alcohol in bicycle crashes is an issue about which we should be concerned. It discusses factors that have the potential to increase the number of bicycle crashes in which alcohol is involved (such growth in the size and diversity of the cyclist population, and balance and coordination demands) and factors which may reduce the importance of alcohol in bicycle crashes (such as time of data factors and child riders). It also examines data availability issues that contribute to difficulties in determining the true magnitude of the issue. Methods: This paper reviews previous research and reports analyses of data from Queensland, Australia, that examine the role of alcohol in Police-reported road crashes. In Queensland it is an offence to ride a bicycle or drive a motor vehicle with a BAC exceeding 0.05% (or lower for novice and professional drivers). Results: In the five years 2003-2007, alcohol was reported as involved in 165 bicycle crashes (4%). The bicycle rider was coded as “under the influence” or “over the prescribed BAC limit” in 15 were single unit crashes (12%). In multi-vehicle bicycle crashes, alcohol involvement was reported for 16 cyclists (0.4%) and 110 operators of other vehicles (3%). Additional analyses including characteristics of the cyclist crashes involving alcohol and the importance of missing data will be discussed in the paper. Conclusion: The increase in participation in cycling and the vulnerability of cyclists to injuries support the need to examine the role of alcohol in bicycle crashes. Current data suggest that alcohol on the part of the vehicle driver is a larger concern than alcohol on the part of the cyclist, but improvements in data collection are needed before more precise conclusions can be drawn.

Social control of the drinking driver

It is more that 20 years since the “Social Control of the Drink Driver” edited by Laurence, Snortum and Zimring (1988) were published. It was, and remains a major examination of the issue involving 17 scientists from all relevant disciplines and policy centres and represents the current practice and experience at the time. While much of, but by no means all, the content is centred on the North American experience the scholarship and range of research data explored through the investigative lens of lawyers, pharmacologists, psychologists, sociologists, criminologists and economists covers all the major issues being examined in Europe, and Australia at the time. More importantly, it presents the policy aspirations and goals of nine countries and includes a comparison of deterrence and the legal context in six countries; emerging technologies for control and the potential contributions of education and rehabilitation. The experience of promoting evidence based policies and practices are generally experienced in all countries as both laborious and painfully slow. However, this ICADTS meeting in Norway provides an opportunity to challenge these feelings by re-examining the current situation compared with that documented over 20yrs ago. This presentation will undertake a reality check on just what we have achieved within that time and try to attribute success and failure towards recommendations for our future endeavours.

Deterring drug drivers : a study into the initial impact of oral random roadside drug testing in Queensland

Objective: The global implementation of oral random roadside drug testing is relatively limited, and correspondingly, the literature that focuses on the effectiveness of this intervention is scant. This study aims to provide a preliminary indication of the impact of roadside drug testing in Queensland. Methods: A sample of Queensland motorists’ (N= 922) completed a self-report questionnaire to investigate their drug driving behaviour, as well as examine the perceived affect of legal sanctions (certainty, severity and swiftness) and knowledge of the countermeasure on their subsequent offending behaviour. Results: Analysis of the collected data revealed that approximately 20% of participants reported drug driving at least once in the last six months. Overall, there was considerable variability in respondent’s perceptions regarding the certainty, severity and swiftness of legal sanctions associated with the testing regime and a considerable proportion remained unaware of testing practices. In regards to predicting those who intended to drug driving again in the future, perceptions of apprehension certainty, more specifically low certainty of apprehension, were significantly associated with self-reported intentions to offend. Additionally, self-reported recent drug driving activity and frequent drug consumption were also identified as significant predictors, which indicates that in the current context, past behaviour is a prominent predictor of future behaviour. To a lesser extent, awareness of testing practices was a significant predictor of intending not to drug drive in the future. Conclusion: The results indicate that drug driving is relatively prevalent on Queensland roads, and a number of factors may influence such behaviour. Additionally, while the roadside testing initiative is beginning to have a deterrent impact, its success will likely be linked with targeted intelligence-led implementation in order to increase apprehension levels as well as the general deterrent effect.

Predicting single-vehicle fatal crashes for two-lane rural highways in Southeastern United States

The rural two-lane highway in the southeastern United States is frequently associated with a disproportionate number of serious and fatal crashes and as such remains a focus of considerable safety research. The Georgia Department of Transportation spearheaded a regional fatal crash analysis to identify various safety performances of two-lane rural highways and to offer guidance for identifying suitable countermeasures with which to mitigate fatal crashes. The fatal crash data used in this study were compiled from Alabama, Georgia, Mississippi, and South Carolina. The database, developed for an earlier study, included 557 randomly selected fatal crashes from 1997 or 1998 or both (this varied by state). Each participating state identified the candidate crashes and performed physical or video site visits to construct crash databases with enhance site-specific information. Motivated by the hypothesis that single- and multiple-vehicle crashes arise from fundamentally different circumstances, the research team applied binary logit models to predict the probability that a fatal crash is a single-vehicle run-off-road fatal crash given roadway design characteristics, roadside environment features, and traffic conditions proximal to the crash site. A wide variety of factors appears to influence or be associated with single-vehicle fatal crashes. In a model transferability assessment, the authors determined that lane width, horizontal curvature, and ambient lighting are the only three significant variables that are consistent for single-vehicle run-off-road crashes for all study locations.

Road crash proneness prediction using data mining

Developing safe and sustainable road systems is a common goal in all countries. Applications to assist with road asset management and crash minimization are sought universally. This paper presents a data mining methodology using decision trees for modeling the crash proneness of road segments using available road and crash attributes. The models quantify the concept of crash proneness and demonstrate that road segments with only a few crashes have more in common with non-crash roads than roads with higher crash counts. This paper also examines ways of dealing with highly unbalanced data sets encountered in the study.