Comparative study of chemical and mechanical retentive systems for bonding of indirect composite resin to commercially pure titanium

This study evaluated the effect of chemical and mechanical surface treatments for cast metal alloys on the bond strength of an indirect composite resin (Artglass) to commercially pure titanium (cpTi). Thirty cylindrical metal rods (3 mm diameter x 60 mm long) were cast in grade-1 cpTi and randomly assigned to 6 groups (n=5) according to the received surface treatment: sandblasting; chemical treatment; mechanical treatment - 0.4 mm beads; mechanical treatment - 0.6 mm beads; chemical/mechanical treatment - 0.4 mm; and chemical/mechanical treatment - 0.6 mm beads. Artglass rings (6.0 mm diameter x 2.0 mm thick) were light cured around the cpTi rods, according manufacturer's specifications. The specimens were invested in hard gypsum and their bond strength (in MPa) to the rods was measured at fracture with a universal testing machine at a crosshead speed of 2.0 mm/min and 500 kgf load cell. Data were analyzed statistically by one-way ANOVA and Tukey test (a=5%). The surface treatments differed significantly from each other (p<0.05) regarding the recorded bond strengths. Chemical retention and sandblasting showed statistically similar results to each other (p=0.139) and both had significantly lower bond strengths (p<0.05) than the other treatments. In conclusion, mechanical retention, either associated or not to chemical treatment, provided higher bond strength of the indirect composite resin to cpTi.

Effect of repeated disinfections by microwave energy on the physical and mechanical properties of denture base acrylic resins

The present study evaluated the effect of repeated simulated microwave disinfection on physical and mechanical properties of Clássico, Onda-Cryl and QC-20 denture base acrylic resins. Aluminum patterns were included in metallic or plastic flasks with dental stone following the traditional packing method. The powder/liquid mixing ratio was established according to the manufacturer's instructions. After water-bath polymerization at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling and finished. Each specimen was immersed in 150 mL of distilled water and underwent 5 disinfection cycles in a microwave oven set at 650 W for 3 min. Non-disinfected and disinfected specimens were subjected to the following tets: Knoop hardness test was performed with 25 g load for 10 s, impact strength test was done using the Charpy system with 40 kpcm, and 3-point bending test (flexural strength) was performed at a crosshead speed of 0.5 mm/min until fracture. Data were analyzed statistically by ANOVA and Tukey's test (α= 0.05%). Repeated simulated microwave disinfections decreased the Knoop hardness of Clássico and Onda-Cryl resins and had no effect on the impact strength of QC-20. The flexural strength was similar for all tested resins.

Evaluation of iris color stability in ocular prosthesis

Accurate iris reproduction in the fabrication of ocular prosthesis in order to match the remaining eye is a key factor to mask the loss and achieve an esthetic outcome for anophthalmic patients. This study evaluated the stability of acrylic paints used for replicating iris color in ocular prostheses by the analysis of two factors: the temperature of the acrylic resin polymerization cycle during prosthesis fabrication and the incidence of sun light, which is the main photodegrading agent undermining the longevity of ocular prostheses. An accelerated aging assay was used for both analyses. Specimens simulating the prosthetic iris in the colors blue, yellow, black, brown and green were fabricated, and were submitted to a colorimetric reading before and after undergoing the thermal conditions of acrylic resin polymerization. Next, the specimens were submitted to an artificial accelerated aging assay with ultraviolet radiation A and weekly colorimetric readings during a 3-week period. The color change (??*) values for the four specimens painted with the same color paint were averaged and the resulting values were considered for statistical analysis. Levine's test and Student's t-test were used to analyze the influence of the temperature of the polymerization cycle during prosthesis fabrication on the color stability of each acrylic resin paint. Friedman's test for three dependent samples was used for analysis of color photodegradation as function of time. Significance level was set at 0.05 for all analyses. It was observed that, after the action of the temperature of the polymerization cycle, alteration above clinically acceptable level of ??*> 3.3 was observed only for the yellow color. After the accelerated aging assay, there were statistically significant differences (p<0.05) as a function of time in the green, brown, black and blue colors. Changes were clinically acceptable for the brown and black colors; slightly above the clinically acceptable limit for the green color; and significantly high and impracticable from a clinical standpoint for the blue color. There was no statistically significant differences (p>0.05) for the yellow color, which presented color change only a little above the clinically acceptable limit. In conclusion: 1. Only the yellow color presented alterations above the clinically acceptable levels after the polymerization cycle; 2. After accelerated aging, there was no changes in the yellow color above the clinically acceptable levels; 3. For the green color, degradation was significant and slightly above the clinically acceptable levels; 4. The black, brown and blue colors presented significant alterations as function of time; the alterations of the brown and black colors were within acceptable clinical levels, while the blue color presented a more accentuated degradation over time.

Effect of chlorhexidine concentration on the bond strength to dentin in primary teeth

PURPOSE: To evaluate the effect of the use of 0.5% and 2% chlorhexidine digluconate on the immediate bond strength of a conventional adhesive system to dentin in primary teeth. METHODS: Twenty-one healthy primary molars were divided into three groups (n=7), being one control (A) and two experimental groups (B and C). After dentin exposure, in Group (A) the adhesive procedure was performed using 37% phosphoric acid gel (15 s); dentin was washed (15 s), air dried (30 s) and rehydrated with water. Groups B and C followed similar procedures but for re-hydration with 0.5% and 2% chlorhexidine, respectively, for 30 s. A resin composite block was built simulating a restoration, and the teeth were stored in distilled water at 37°C for 24 h before the microtensile bond strength test. The bond strength data were analyzed by analysis of variance. RESULTS: No statistically significant difference in bond strength was found among the tested groups (P>0.05) CONCLUSION: The 0.5% and 2% concentrations of chlorhexidine presented similar behavior and caused no adverse effects on the bond strength to dentin in primary teeth.

Use of flowable composite as intermediary layer in non-carious cervical lesions restored with composite resin: 48-month follow-up

PURPOSE: In this case report, the clinical performance of a microhybrid resin composite placed with or without a flowable resin composite was compared, over a 48-month period. CASE DESCRIPTION: The patient of this case report presented 2 pairs of equivalent cervical abfraction lesions, under occlusion. Four restorations were placed in teeth 34, 35, 44 and 45. The restorations were divided into groups (Single Bond + Filtek-Flow + Filtek Z250 or Single Bond + Filtek Z250) and the materials were applied according to the manufactures instructions. Two previously calibrated operators placed the restorations and two other independent examiners evaluated the restorations at baseline and after 48 months, according to the USPHS criteria and modified criteria for color match. CONCLUSION: After 48 months of evaluation the lesions restored with Filtek-Flow as a liner under Filtek Z250 did not show better clinical performance than the restorations without Filtek-Flow. All restorations showed a trend toward dark yellowing after 48 months.

Adsorption of amyloglucosidase from Aspergillus niger NRRL 3122 using ion exchange resin

Amyloglucosidase enzyme was produced by Aspergillus niger NRRL 3122 from solid-state fermentation, using deffated rice bran as substrate. The effects of process parameters (pH, temperature) in the equilibrium partition coefficient for the system amyloglucosidase - resin DEAE-cellulose were investigated, aiming at obtaining the optimum conditions for a subsequent purification process. The highest partition coefficients were obtained using 0.025M Tris-HCl buffer, pH 8.0 and 25ºC. The conditions that supplied the highest partition coefficient were specified, the isotherm that better described the amyloglucosidase process of adsorption obtained. It was observed that the adsorption could be well described by Langmuir equation and the values of Qm and Kd estimated at 133.0 U mL-1 and 15.4 U mL-1, respectively. From the adjustment of the kinetic curves using the fourth-order Runge-Kutta algorithm, the adsorption (k1) and desorption (k2) constants were obtained through optimization by the least square procedure, and the values calculated were 2.4x10-3 mL U-1 min-1 for k1 and 0.037 min-1 for k2 .

Tensile bond strength and SEM analysis of enamel etched with Er:YAG laser and phosphoric acid: a comparative study In vitro

Er:YAG laser has been studied as a potential tool for restorative dentistry due to its ability to selectively remove oral hard tissue with minimal or no thermal damage to the surrounding tissues. The purpose of this study was to evaluate in vitro the tensile bond strength (TBS) of an adhesive/composite resin system to human enamel surfaces treated with 37% phosphoric acid, Er:YAG laser (lambda=2.94 mum) with a total energy of 16 J (80 mJ/pulse, 2Hz, 200 pulses, 250 ms pulse width), and Er:YAG laser followed by phosphoric acid etching. Analysis of the treated surfaces was performed by scanning electron microscopy (SEM) to assess morphological differences among the groups. TBS means (in MPa) were as follows: Er:YAG laser + acid (11.7 MPa) > acid (8.2 MPa) > Er:YAG laser (6.1 MPa), with the group treated with laser+acid being significantly from the other groups (p=0.0006 and p= 0.00019, respectively). The groups treated with acid alone and laser alone were significantly different from each other (p=0.0003). The SEM analysis revealed morphological changes that corroborate the TBS results, suggesting that the differences in TBS means among the groups are related to the different etching patterns produced by each type of surface treatment. The findings of this study indicate that the association between Er:YAG laser and phosphoric acid can be used as a valuable resource to increase bond strength to laser-prepared enamel.

Distribuição de tensões em mini-implantes ortodônticos

O objetivo deste trabalho foi avaliar a distribuição de tensões na resina em contato com os filetes de roscas de mini-implantes cilíndricos e cônicos, submetidos à carga lateral e torção de inserção. Um modelo fotoelástico foi confeccionado com gelatina transparente, para simular o osso alveolar. O modelo foi observado com um polariscópio plano e fotografado antes e após a ativação dos mini-implantes com força lateral e de inserção. A aplicação de cargas laterais provocou momentos fletores nos mini-implantes, aparecimento de franjas isocromáticas ao longo dos filetes do corpo dos mini-implantes e no ápice. Quando foi aplicado o torque de inserção, verificou-se a concentração de tensões próxima ao ápice. Concluiu-se que: (1) o mini-implante cilíndrico apresentou maior concentração de tensões no ápice, e (2) o mini-implante cônico apresentou maior concentração de tensões nos filetes de rosca apicais.

Effect of experimental heat treatment on mechanical properties of resin composites

The aim of this study was to verify the influence of an experimental heat treatment (170ºC/10 min) using a casting furnace on the mechanical properties (hardness and flexural strength) of 2 commercial direct resin composites (TPH Spectrum and Filtek P60) compared to a commercial indirect resin system (BelleGlass). Heat treatment temperature was determined after thermal characterization by thermogravimetry (TG) and differential scanning calorimetry (DSC). Data was analyzed by ANOVA and Tukey's test at 5% significance level. There was statistical significance for the main factor heat treatment (p=0.03) and composite (p=0.02), for flexural strength. For Knoop hardness, only the main factor composite was statistically significant (p=0.00). P60 presented higher hardness than TPH. No statistically significant correlation between mechanical properties tested was detected. Based on these results, it was possible to conclude that heat treatment influenced flexural strength of direct composites, while it was not observed for hardness. The association of direct composites with a simple post-cure heat treatment may be an alternative for current indirect composite systems, although more studies are needed to verify other properties of the composites for this application.

Irrigação do timo em aves da linhagem Paraíso Pedrês (Gallus gallus domesticus)

A vascularização arterial do timo (número, origem e ordenação) bem como a distribuição parenquimal dos ramos penetrantes foram estudadas em 40 aves da linhagem Paraíso Pedrês. Trinta aves foram injetadas com látex e dissecadas, enquanto 10 aves tiveram seus sistemas arteriais injetados com resina (metil metacrilato e mercox) para a preparação de moldes vasculares. A principal fonte de irrigação encontrada foi a associação dos ramos oriundos das artérias comuns do nervo vago, tireóideas e ingluviais, sendo que seus ramos penetravam o parênquima dos lobos, principalmente pelas suas extremidades cranial e caudal. A partir da penetração, os ramos tímicos apresentavam distribuição predominante para a periferia do lobo, formando uma trama capilar poligonal, com espaços irregulares, característica de um órgão linforreticular.

Effects of croton urucurana extracts and crude resin on Anagasta kuehniella (Lepidoptera: Pyralidae)

Hundreds of plant species have been studied in order to find out the active ingredient responsible for their insecticidal activity against the pests of economic importance. To verify the insecticidal activity in the husk of stem of Croton urucurana Baillon 1864 (Euphorbiaceae) against Anagasta kuehniella Zeller 1879 (Lepidoptera: Pyralidae), the methanolic (EMeOH) extract, dichloromethane fraction (FDM), ethyl acetate fraction (FAE) and crude resin, incorporated into an artificial diet were evaluated. EMeOH (0.5, 1.0 and 2.0%) and crude resin (2.0%) interfered with neither the weight nor the survival of fourth instar larvae and other analyzed parameters. FDM (2.0%) fraction caused mortality of 65%, and the artificial diet containing 2.0, 1.0 and 0.5% FAE caused 100, 55 and 68% mortality respectively when compared with the control, confirming the least efficiency rates of food conversion for FDM(2.0%) and FAE(1.0%). The tryptic analysis performed with the midgut fluid of fourth-instar larvae demonstrated that tryptic and chymiotryptic activities for the larvae fed artificial diet containing EMeOH and crude resin were not different.

Aspectos morfométricos do nervo hipoglosso humano em adultos e idosos

OBJETIVO: Realizar análise morfométrica das fibras mielínicas do nervo hipoglosso direito, em dois grupos etários, com a finalidade de verificar modificações quantitativas decorrentes do processo de envelhecimento. FORMA DE ESTUDO: anatômico. MATERIAL E MÉTODO: Foi coletado fragmento de 1cm do nervo hipoglosso direito de 12 cadáveres do sexo masculino, sem antecedentes para doenças como diabetes, alcoolismo e neoplasia maligna. A amostra foi dividida em dois grupos: grupo adulto (idade inferior a 60 anos), composto por seis cadáveres; grupo idoso (idade igual ou superior a 60 anos), composto por seis cadáveres. O material foi fixado em solução contendo 2,5% de glutaraldeído e 2% de paraformaldeído; pós-fixado em tetróxido de ósmio 2%; desidratado em concentrações crescentes de etanol e incluído em resina epóxi. Cortes semifinos de 0,3¼m de espessura foram obtidos, corados com azul de toluidina a 1% e avaliados em microscópio de luz acoplado a sistema analisador de imagens. Os seguintes dados morfométricos foram quantificados: área de secção transversal intraperineural, número e o diâmetro das fibras mielínicas. RESULTADOS: A área intraperineural do nervo hipoglosso foi semelhante nos dois grupos etários (p=0,8691). A média da área no grupo adulto foi de 1,697 mm2, e no grupo idoso foi de 1,649 mm2. O número total de fibras mielínicas do nervo hipoglosso foi semelhante nos dois grupos etários (p=0,9018). O grupo adulto apresentou média de 10.286 ± 2308 fibras mielínicas e o grupo idoso apresentou média de 10.141 ± 1590 fibras mielínicas. Foi observada distribuição bimodal das fibras mielínicas, com pico acentuado nas fibras de 9¼m e outro menor nas fibras de 2¼m. CONCLUSÃO: A área intraperineural e o número total de fibras mielínicas do nervo hipoglosso direito é semelhante nos dois grupos etários.

Comparação histológica entre o osso desmineralizado e polímero de mamona sobre a regeneração óssea

O presente estudo tem por objetivo analisar histologicamente o efeito de uma matriz óssea desmineralizada de origem humana e de uma resina poliuretana derivada do óleo da mamona sobre o processo de reparação óssea. MATERIAIS E MÉTODOS: Foram utilizados 24 coelhos e em cada calvária foram preparadas duas cavidades cirúrgicas, sendo uma do lado direito e a outra do lado esquerdo da sutura parietal. Os animais foram divididos em dois grupos. No grupo I, a cavidade experimental (lado direito) foi preenchida com a matriz óssea desmineralizada de origem humana, enquanto no grupo II a cavidade experimental foi preenchida com a poliuretana derivada do óleo de mamona. As cavidades de controle foram preenchidas apenas com o sangue do animal. Os animais foram sacrificados nos períodos pós-operatórios de 4, 7 e 15 semanas. RESULTADOS: A análise histológica revelou que tanto o grupo controle quanto os grupos I e II apresentaram um aumento na neoformação óssea ao longo do tempo, sendo que esta reparação se deu mais rapidamente no grupo controle, mesmo mostrando diminuição importante na espessura. CONCLUSÕES: Ambos os materiais apresentaram-se biocompatíveis, sendo a poliuretana reabsorvida mais tardiamente e considerada de melhor resultado em relação ao outro material empregado.

Níveis críticos de fósforo em solos cultivados com cana-de-açúcar em Pernambuco

Em Pernambuco, a disponibilidade de P é avaliada sem se considerarem características físicas, químicas, ou, mineralógicas dos solos. Este trabalho teve como objetivos determinar os níveis críticos de P em diferentes solos, utilizando-se diferentes extratores químicos, considerando-se a quantidade e a qualidade da fração argila e relacionar as características físicas, químicas e mineralógicas dos solos com os níveis críticos de P. Os solos foram classificados como: Argissolo Amarelo distrocoeso (PAdx); Latossolo Amarelo distrófico (LAd); Argissolo Amarelo distrófico (PAd); Gleissolo háplico eutrófico (GXve) e Espodossolo cárbico duripânico (EKo). Os tratamentos consistiram em sete doses de P, determinadas de acordo com a capacidade máxima de adsorção de P (CMAP). O delineamento experimental foi em blocos ao acaso, com quatro repetições. Foram coletadas amostras de solo na área útil das parcelas. Essa amostragem foi realizada 30 dias após o plantio e aplicação das doses de P, numa profundidade de 0,0-0,2 m. Nessas amostras, determinaram-se o teor de P pelos extratores Mehlich-1, Mehlich-3, Bray-1 e Resina de Troca Iônica (RTA). Com os teores de P no solo e a produção agrícola, determinaram-se os níveis críticos de P no solo. A RTA extraiu mais P independentemente do tipo de solo. Os níveis críticos de P no solo foram dependentes da CMAP, da quantidade de argila e do P remanescente (P-rem), quando o extrator para avaliação do P disponível foi o Mehlich-1. Os níveis críticos no solo determinados pela RTA não foram dependentes de nenhuma característica química e, ou, física dos solos.

Condições sanitárias das águas de irrigação de hortas do município de São Paulo: II. Isolamento de vírus entéricos

Foram pesquisados vírus entéricos nas águas de irrigação de onze hortas do município de São Paulo. Das amostras das águas de cinco hortas foram isolados os seguintes enterovírus: vírus de poliomielite tipo I e tipo III e vírus Coxsackie tipo A16 e tipo A7. Os resultados evidenciam a superioridade do método de adsorção à resina Dowex, para isolamento de vírus de águas contaminadas com esgotos. O encontro de vírus naquelas águas dá ao aspecto sanitário dêste problema, particular importância.