State of the art and open questions on cathode preparation based on carbon coated lithium iron phosphate

One important component with particular relevance in battery performance is the cathode, being one of the main responsible elements for cell capacity and cycle life. Carbon coated lithium iron phosphate, C-LiFePO4, active material is one of the most promising cathode materials for the next generation of large scale lithium ion battery applications and strong research efforts are being devoted to it, due to its excellent characteristics, including high capacity, ~170 mAh/g, and safety. This review summarizes the main developments on C-LiFePO4 based cathode film preparation and performance. The effect of the binder, conductive additive, relationship between active material-binder-conductive additive and drying step, in the electrode film fabrication and performance is presented and discussed. Finally, after the presentation of the cell types fabricated with C-LiFePO4 active material and their performance, some conclusions and guidelines for further investigations are outlined.

Degradation of all-inkjet-printed organic thin-film transistors with TIPS-pentacene under processes applied in textile manufacturing

Printed electronics represent an alternative solution for the manufacturing of low-temperature and large area flexible electronics. The use of inkjet printing is showing major advantages when compared to other established printing technologies such as, gravure, screen or offset printing, allowing the reduction of manufacturing costs due to its efficient material usage and the direct-writing approach without requirement of any masks. However, several technological restrictions for printed electronics can hinder its application potential, e.g. the device stability under atmospheric or even more stringent conditions. Here, we study the influence of specific mechanical, chemical, and temperature treatments usually appearing in manufacturing processes for textiles on the electrical performance of all-inkjet-printed organic thin-film transistors (OTFTs). Therefore, OTFTs where manufactured with silver electrodes, a UV curable dielectric, and 6,13-bis(triisopropylsilylethynyl) pentance (TIPS-pentacene) as the active semiconductor layer. All the layers were deposited using inkjet printing. After electrical characterization of the printed OTFTs, a simple encapsulation method was applied followed by the degradation study allowing a comparison of the electrical performance of treated and not treated OTFTs. Industrial calendering, dyeing, washing and stentering were selected as typical textile processes and treatment methods for the printed OTFTs. It is shown that the all-inkjet-printed OTFTs fabricated in this work are functional after their submission to the textiles processes but with degradation in the electrical performance, exhibiting higher degradation in the OTFTs with shorter channel lengths (L=10 μm).

Inkjet printing technology for flexible pressure sensors

Tese de Doutoramento Ciência e Engenharia de Polímeros e Compósitos.

The role of automatic shape and position recognitionin streamlining manufacturing

The main features of most components consist of simple basic functional geometries: planes, cylinders, spheres and cones. Shape and position recognition of these geometries is essential for dimensional characterization of components, and represent an important contribution in the life cycle of the product, concerning in particular the manufacturing and inspection processes of the final product. This work aims to establish an algorithm to automatically recognize such geometries, without operator intervention. Using differential geometry large volumes of data can be treated and the basic functional geometries to be dealt recognized. The original data can be obtained by rapid acquisition methods, such as 3D survey or photography, and then converted into Cartesian coordinates. The satisfaction of intrinsic decision conditions allows different geometries to be fast identified, without operator intervention. Since inspection is generally a time consuming task, this method reduces operator intervention in the process. The algorithm was first tested using geometric data generated in MATLAB and then through a set of data points acquired by measuring with a coordinate measuring machine and a 3D scan on real physical surfaces. Comparison time spent in measuring is presented to show the advantage of the method. The results validated the suitability and potential of the algorithm hereby proposed

La paletina: un pinzell pla i prim

Treball de recerca realitzat per una alumna d'ensenyament secundari i guardonat amb un Premi CIRIT per fomentar l'esperit científic del Jovent l'any 2009. L’origen de l’autora és la Sénia, un poble d'uns 6000 habitants de la província de Tarragona, on, tot i el predomini actual de la fabricació de mobles, les primeres mostres d'industrialització foren el paper i els pinzells. L’arrelament de la indústria pinzellera de la seva família, ha estat el motiu que l’ha portat a desenvolupar aquest treball sobre la paletina, un tipus de pinzell. L'objectiu del treball ha estat dissenyar un model de paletina, a partir de proves pràctiques i d'estudis estadístics sobre quins són els components més adients. En primer lloc, es fa una descripció detallada dels components de la paletina. A continuació, s’estudia el seu procés de fabricació, primer des del punt de vista manual i després d'acord amb els procediments moderns. Finalment, a partir d'un experiment i amb el corresponent estudi estadístic, s’arriba a una nova proposta de paletina amb unes condicions òptimes de qualitat i rendiment. A més també es descriu el procés de fabricació de la paletina que es duia a terme uns cinquanta anys enrere i es pot valorar, així, tant el mèrit del procés en aquella època com també l'evolució tecnològica que s'ha dut a terme fins al moment.

Adverse effects of industrial multiwalled carbon nanotubes on human pulmonary cells

The aim of this study was to evaluate adverse effects of multiwalled carbon nanotubes (MWCNT), produced for industrial purposes, on the human epithelial cell line A549. MWCNT were dispersed in dipalmitoyl lecithin (DPL), a component of pulmonary surfactant, and the effects of dispersion in DPL were compared to those in two other media: ethanol (EtOH) and phosphate-buffered saline (PBS). Effects of MWCNT were also compared to those of two asbestos fibers (chrysotile and crocidolite) and carbon black (CB) nanoparticles, not only in A549 cells but also in mesothelial cells (MeT5A human cell line), used as an asbestos-sensitive cell type. MWCNT formed agglomerates on top of both cell lines (surface area 15-35 μm2) that were significantly larger and more numerous in PBS than in EtOH and DPL. Whatever the dispersion media, incubation with 100 μg/ml MWCNT induced a similar decrease in metabolic activity without changing cell membrane permeability or apoptosis. Neither MWCNT cellular internalization nor oxidative stress was observed. In contrast, asbestos fibers penetrated into the cells, decreased metabolic activity but not cell membrane permeability, and increased apoptosis, without decreasing cell number. CB was internalized without any adverse effects. In conclusion, this study demonstrates that MWCNT produced for industrial purposes exert adverse effects without being internalized by human epithelial and mesothelial pulmonary cell lines. [Authors]

Effects of polymer-coated multi-wall carbon nanotubes on mouse RAW 264.7 macrophages

Surface characteristics (area, chemical reactivity) play an important role in cell response to nanomaterials. The aim of this study was to evaluate the oxidative and inflammatory effects of multi−wall carbon nanotubes (MWCNT) uncoated (P0) or coated with carboxylic polyacid or polystyrene polybutadiene polymetacrylate of methyl polymers (P1 and P2 respectively) on murine macrophages (RAW 264.7 cell line). Carbon black nanoparticles (CB, diameter 95 nm) and crocidolite fibers (diameter: 80 nm, length: < 10 μm) were used as controls. Surface functional groups present on MWCNTs were analyzed by Knudsen flow reactor. The amount of acidic sites was P1> P0> P2, for basic sites was P0> P1>> P2 and for oxidizable sites was P0> P2> P1. In contact with cells, P2 formed smaller aggregates than P0 and P1, which were of similar size. Optical microscopy showed the formation of vacuoles after exposure only to P0, P1 and crocidolite. Incubation of cells with P0, P1 and crocidolite fibers induced a significant and similar decrease in metabolic activity, whereas P2 and CB had no effect. Cell number and membrane permeability were unmodified by incubation with the different particles. Incubation of macrophages with P0, P1 and crocidolite induced a dose− and time−dependent increase in mRNA expression of oxidative stress marker (HO−1, GPX1) and inflammatory mediators (TNF−a, MIP−2). No such responses were observed with P2 and CB. In conclusion, MWCNT coated with a carboxylic polyacid polymer exerted similar oxidative and inflammatory effects to uncoated MWCNT. By contrast, no such effects were observed with MWCNT coated with a polystyrene−based polymer. This kind of coating could be useful to decrease MWCNT toxicity.

Evaluation of Recycled Rubber in Asphalt Cement Concrete - Field Testing, Final Report for HR-330, 330A, 330B, 330C, 330D, 2002

Roughly 242 million used tires are generated annually in the United States. Many of these tires end up being landfilled or stockpiled. The stockpiles are unsightly, unsanitary, and also collect water which creates the perfect breeding ground for mosquitoes, some of which carry disease. In an effort to reduce the number of used tire stockpiles the federal government mandated the use of recycled rubber in federally funded, state implemented department of transportation (DOT) projects. This mandate required the use of recycled rubber in 5% of the asphalt cement concrete (ACC) tonnage used in federally funded projects in 1994, increasing that amount by 5% each year until 20% was reached, and remaining at 20% thereafter. The mandate was removed as part of the appropriations process in 1994, after the projects in this research had been completed. This report covers five separate projects that were constructed by the Iowa Department Of Transportation (DOT) in 1991 and 1992. These projects had all had some form of rubber incorporated into their construction and were evaluated for 5 years. The conclusion of the study is that the pavements with tire rubber added performed essentially the same as conventional ACC pavement. An exception was the use of rubber chips in a surface lift. This performed better at crack control and worse with friction values than conventional ACC. The cost of the pavement with rubber additive was significantly higher. As a result, the benefits do not outweigh the costs of using this recycled rubber process in pavements in Iowa.

Biogeochemical processes controlling oxygen and carbon isotopes of diatom silica in Late Glacial to Holocene lacustrine rhythmites

Biogeochemical cycles and sedimentary records in lakes are related to climate controls on hydrology and catchment processes. Changes in the isotopic imposition of the diatom frustules (δ 18 O diatom and δ 13 C diatom ) in lacustrine sediments can be used to reconstruct palaeoclimatic and palaeoenvironmental changes. The Lago Chungará (Andean Altiplano, 18°15 ′ S, 69°10 ′ W, 4520 masl) diatomaceous laminated sediments are made up of white and green multiannual rhythmites. White laminae were formed during short-term diatom super-blooms, and are composed almost exclusively of large-sized Cyclostephanos andinus.These diatoms bloom during mixing events when recycled nutrients from the bottom waters are brought to the surface and/or when nutrients are introduced from the catchment during periods of strong runoff. Conversely, the green laminae are thought to have been deposited over several years and are composed of a mixture of diatoms (mainly smaller valves of C. andinus and Discostella stelligera ) and organic matter. These green laminae reflect the lake's hydrological recovery from a status favouring the diatom super-blooms (white laminae) towards baseline conditions. δ 18 O diatom and δ 13 C diatom from 11,990 to 11,530 cal years BP allow us to reconstruct shifts in the precipitation/evaporation ratio and changes in the lake water dissolved carbon concentration, respectively. δ 18 O diatom values indicate that white laminae formation occurred mainly during low lake level stages, whereas green laminae formation generally occurred during high lake level stages. The isotope and chronostratigraphical data together suggest that white laminae deposition is caused by extraordinary environmental events. El Niño-Southern Oscillation and changes in solar activity are the most likely climate forcing mechanisms that could trigger such events, favouring hydrological changes at interannual-to-decadal scale. This study demonstrates the potential for laminated lake sediments to document extreme pluriannual events.

Tuotteen suunnitteluketjun tehostaminen 3D-ympäristössä

Tämä diplomityö on tehty Andritz Oy:lle Washers & Filters tuoteryhmään. Työ on osa 3D-suunnittelujärjestelmän käyttöönottoprojektia. Tavoitteena on arvioida uuden laitesuunnittelujärjestelmän vaikutuksia yrityksen tietojärjestelmiin ja toimintatapoihin sekä etsiä potentiaalisia tulevaisuuden kehityskohteita. Suunnittelutietoa hyödyntäviä sidosryhmien edustajia haastattelemalla selvitettiin järjestelmille ja ohjelmistoille asetettavia vaatimuksia. Ohjelmistoihin tutustumalla saatiin käsitys niiden nykytilasta ja kehityssuunnista. 3D-geometrian hyödyntämiseen perustuvilla järjestelmillä voidaan poistaa päällekäistä työtä sekä lyhentää läpimenoaikoja suunnittelussa ja valmistuksessa sijoittamalla työvaiheita rinnakkain. Suurimmat 3D-suunnittelun edut saavutetaan tuotekehitysvaiheessa, tuotemuutoksia tehtäessä sekä valmistusprosesseja suunniteltaessa. Ongelmallisimmat osa-alueet tietojärjestelmien kehittämisessä ovat ensi-sijaisesti tiedonsiirto ohjelmistojen välillä, työntekijöiden muutosvastarinta sekä laadukkaiden järjestelmien korkea hinta. Laajojen tietojärjestelmä-projektien läpivienti on hyvin haastavaa ja onnistuminen vaatii kaikkien sidosryhmien mukana olemista ja tarkkaa projektin koordinointia.

Carbon balance of Fibre-Based Package

Customers are more and more interested in the environmental impacts of the products they purchase. Different labels give the required environmental information to consumers and the labels might affect to the consuming decisions. The European Union has set a plan for sustainable consuming, which encourages industry and commerce to calculate carbon footprints for the products. A term “carbon footprint” means carbon dioxide emissions across the product lifecycle. In this thesis, carbon footprints are calculated for two different fibre-based packages. In the end, greenhouse gas emissions from fibre-package production are compared to greenhouse gas emissions from PET bottle production. The data for mill processes is exact and monitored in the mill. In addition, data was gathered from raw material and material suppliers, customers, official records, KCL-eco databases and literature. The data for PET bottle is sourced from literature. End-of-life operations affect greatly on the carbon footprint of a fibre-based package. The results show that the carbon footprint is smallest when used packages are recycled. Recycling saves also natural resources. If used packages are not recyclable for some reason, it is recommended to use them in energy production. Through waste incineration fossil fuels could be substituted and greenhouse gas emissions avoided.

Kinetic study of the cobalt electrodeposition onto glassy carbon electrode from ammonium sulfate solutions

We carried out an electrochemical study of the cobalt electrodeposition onto glassy carbon electrode from an aqueous solution containing 10-2 M of CoSO4 + 1 M (NH4)2SO4 at natural pH 4.5. The potentiostatic study indicated a progressive 3D nucleation and growth during the deposition process. The average diffusion coefficient calculated for this system was 2.65 X 10-6 cm² s-1 while the ΔG for the formation of stable nucleus was 6.50 X 10-20 J/nuclei. The scanning electron microscopy images indicated the formation of small and homogeneous nucleus onto GCE of approximately 300 nm.

Copper electrodeposition on glassy carbon and highly oriented pyrolytic graphite substrates from perchlorate solutions

In present work, we analyzed the copper electrodeposition onto GCE (System I) and HOPGE (System II) from perchlorate solutions. The current density transients obtained from system I and II were well described through a kinetic mechanism that involves four different contributions: (a) a Langmuir type adsorption process, b) an electron transfer from Cu2+→Cu+, (c) a 3D nucleation limited by a mass transfer reaction and (d) a proton reduction process. It was observed that the values of the nucleation rate, the number of active nucleation sites were increased with the overpotential and they are bigger onto GCE in comparison with HOPGE.

Ultrafiltration membranes from waste polyethylene terephthalate and additives: synthesis and characterization

The synthesis and characterization of asymmetric ultrafiltration membranes from recycled polyethylene terephthalate (PET) and polyvinylpyrrolidone (PVP) is reported. PET is currently used in many applications, including the manufacture of bottles and tableware. Monomer extraction from waste PET is expensive, and this process has not yet been successfully demonstrated on a viable scale. Hence, any method to recycle or regenerate PET once it has been used is of significant importance from scientific and environmental research viewpoints. Such a process would be a green alternative due to reduced raw monomer consumption and the additional benefit of reduced manufacturing costs. The membranes described here were prepared by a phase-inversion process, which involved casting a solution containing PET, m-cresol as solvent, and polyethylene glycol (PEG) of different molecular weights as additives. The membranes were characterized in terms of pure water permeability (PWP), molecular weight cut-off (MWCO), and flux and membrane morphology. The results show that the addition of PEG with high molecular weights leads to membranes with higher PWP. The presence of additives affects surface roughness and membrane morphology.

Creating carbon footprint calculating tool for plastic packaging products

The environmental challenges of plastic packaging industry have increased remarkably along with climate change debate. The interest to study carbon footprints of packaging has increased in packaging industry to find out the real climate change impacts of packaging. In this thesis the greenhouse gas discharges of plastic packaging during their life cycle is examined. The carbon footprint is calculated for food packaging manufactured from plastic laminate. The structure of the laminate is low density polyethylene (PE-LD) and oriented polypropylene (OPP), which have been joined together with laminating adhesive. The purpose is to find out the possibilities to create a carbon footprint calculating tool for plastic packaging and its usability in a plastic packaging manufacturing company. As a carbon footprint calculating method PAS 2050 standard has been used. In the calculations direct and indirect greenhouse gas discharges as well as avoided discharges are considered. Avoided discharges are born for example in packaging waste utilization as energy. The results of the calculations have been used to create a simple calculating tool to be used for similar laminate structures. Although the utilization of the calculating tool is limited to one manufacturing plant because the primary activity data is dependent of geographical location and for example the discharges of used energy in the plant. The results give an approximation of the climate change potential caused by the laminate. It is although noticed that calculations do not include all environmental impacts of plastic packaging´s life cycle.