EFFECT OF GRAIN-BOUNDARY MICROSTRUCTURE ON CAVITY NUCLEATION IN A NICKEL-BASED SUPERALLOY.

A study is presented of grain-boundary cavitation produced in Nimonic 80A by cold-deformation and stress-free annealing. The cavities were found to originate either from transverse cracking of carbide particles, or from decohesion of the particle-grain boundary interfaces. This decohesion could occur either during deformation, or during annealing. The cavities were invariably located at or close to the point of impingement of a matrix slip band on the grain boundary, but not all slip bands at a particular boundary were associated with cavitation. Quantitative evidence is presented showing that the mean number of dislocations associated with each slip band increases with macroscopic strain, but there is considerable variation between slip bands. This accounts for the differential ability of slip bands to result in cavity nucleation.

Concentration and distribution of heavy metals (lead, cadmium, chromium, copper, nickel, zinc) in Karachi shore and offshore sediments

A study to measure the heavy metal pollution level in the sediment of coastal and offshore area indicates that high concentration of heavy metals were found around Manora channel and eastern coast of Karachi. In comparison with coastal areas, relatively low concentration of heavy metals was recorded in the offshore area. The result shows that sewage and industrial wastes are the main source of heavy metal pollution in the coastal area. The concentration of heavy metals in the sediments is as follows: Chromium 10.4-33.69, nickel 13.3-47.6, lead 10.0-39.04, cadmium 0.08-0.21, zinc 7.4-73.2 and copper 9.44-18.56 mg/kg. In the offshore areas strong correlation was observed between copper and organic carbon, and calcium carbonate and cadmium. In the shore area such correlation has been recorded among nickel, chromium, zinc, and chromium and copper. The Karachi. coast is viewed as moderately polluted when compared to other continental coastal areas.

Genotoxic effect of nickel chloride and zinc sulphate on fish Hypophthalmichthys molitrix

The present investigation is to assess the genotoxic potential of nickel chloride and zinc sulphate on gill cells of silver carp Hypophthalmichthys molitrix. Fishes were exposed in sublethal concentration of nickel chloride 5. 7 mg/1 and zinc sulphate 6.8 mg/1, and sampled at 10, 20 and 30 days. Nickel chloride and zinc sulphate treated fishes exhibited an apparent increase in the aberration frequency and a decrease in the mitotic index as compared to control. Acentric fragment, chromatid break, endoreduplication, chromatid gap, centromeric fusion, ploidy, sticky plate, dicentric chromosome, clumping and partial sticky plates were some of the abnormalities observed. The chromosomal aberrations in the treated fishes were significant compared to control.

Copper-nickel alloys for marine aquacultural engineering

Engineering developments, problems of marine corrosion, fouling and practical innovative applications of copper-nickel alloys in comparison with other materials for marine aquacultural engineering are presented. Coefficient of drag and hydrodynamic force acting on nylon and polyethylene net enclosures have shown a four-fold increase of force in four months at the Cochin harbour due to fouling. Corrosion behaviour of copper-nickel and other copper base alloys are also presented. Effects of copper additions to culture water are reviewed.

Local stress relaxation and shear banding in a dry foam under shear.

We have developed a realistic simulation of 2D dry foams under quasistatic shear. After a short transient, a shear-banding instability is observed. These results are compared with measurements obtained on real 2D (confined) foams. The numerical model allows us to exhibit the mechanical response of the material to a single plastication event. From the analysis of this elastic propagator, we propose a scenario for the onset and stability of the flow localization process in foams, which should remain valid for most athermal amorphous systems under creep flow.

Graphene-passivated nickel as an oxidation-resistant electrode for spintronics.

We report on graphene-passivated ferromagnetic electrodes (GPFE) for spin devices. GPFE are shown to act as spin-polarized oxidation-resistant electrodes. The direct coating of nickel with few layer graphene through a readily scalable chemical vapor deposition (CVD) process allows the preservation of an unoxidized nickel surface upon air exposure. Fabrication and measurement of complete reference tunneling spin valve structures demonstrate that the GPFE is maintained as a spin polarizer and also that the presence of the graphene coating leads to a specific sign reversal of the magneto-resistance. Hence, this work highlights a novel oxidation-resistant spin source which further unlocks low cost wet chemistry processes for spintronics devices.

Dynamic compression of foam supported plates impacted by high velocity soil

The response of back-supported buffer plates comprising a solid face sheet and foam core backing impacted by a column of high velocity particles (sand slug) is investigated via a lumped parameter model and coupled discrete/continuum simulations. The buffer plate is either resting on (unattached) or attached to a rigid stationary foundation. The lumped parameter model is used to construct maps of the regimes of behaviour with axes of the ratio of the height of the sand slug to core thickness and the normalised core strength. Four regimes of behaviour are identified based on whether the core compression ends prior to the densification of the sand slug or vice versa. Coupled discrete/continuum simulations are also reported and compared with the lumped parameter model. While the model predicted regimes of behaviour are in excellent agreement with numerical simulations, the lumped parameter model is unable to predict the momentum transmitted to the supports as it neglects the role of elasticity in both the buffer plate and the sand slug. The numerical calculations show that the momentum transfer is minimised for intermediate values of the core strength when the so-called "soft-catch" mechanism is in play. In this regime the bounce-back of the sand slug is minimised which reduces the momentum transfer. However, in this regime, the impulse reduction is small (less than 10% of that transferred to a rigid structure). For high values of the core strength, the response of the buffer plate resembles a rigid plate with nearly no impulse mitigation while at low values of core strength, a slap event occurs when the face sheet impinges against the foundation due to full densification of the foam core. This slap event results in a significant enhancement of the momentum transfer to the foundation. The results demonstrate that appropriately designed buffer plates have potential as impulse mitigators in landmine loading situations. © 2013 Elsevier Ltd. All rights reserved.