Tailoring the Microwave Dielectric Properties of BaRE2Ti4012 and BaRE2Ti5014 Ceramics by Compositional Variations

Ceramic dielectric resonators in the BaO-RE2O3-TiO2 (RE = rare earth) system have been prepared by the conventional solid state ceramic route. The dielectric properties have been tailored by substitution of different rare earth oxides and by bismuth oxide addition. The dielectric constants increased with Bi addition whereas the 0 decreased. The temperature coefficient of the resonant frequency improved with bismuth addition

Loss characterization in rhodamine 6G doped polymer film waveguide by side illumination fluorescence

We report the position dependent tuning of fluorescence emission from rhodamine 6G doped polymethylmethacrylate film waveguide using a side illumination technique. The transmitted fluorescence as a function of the distance from the point of illumination is measured by translating the waveguide horizontally across a monochromatic light source. This technique has been utilized to characterize the optical loss in dye doped waveguides. We observe that the optical loss coefficients for shorter and longer distances of propagation through the dye doped waveguide are different. At longer distance of propagation a decrease in optical loss coefficient is observed

Variations on the infaunal polychaetes due to bottom trawling along the inshore waters of Kerala (south-west coast of India)

Variations of the infaunal polychates populations due to bottom trawling were studied during December 2000 to November 2002 at depth ranging from 0-50 m along Cochin-Munambam area (Kerala, long. 76degree10'94" to 75degree 56' and lat.9degree58' to 10degree10'), in the southwest coast of India.Infaunal polychaetes from the sediment samples were collected both before and after experimental trawling in order to assess the variations on their abundance (no.m-2),biomass(g.m-2) and diversity due to bottom trawling .Highest variations in polychaetes were recorded at station 9 in May 2002 where polychaete abundance increased to 20710 no.m-2 after trawling from 2787 no.m-2 before trawling.Biomass showed highest variations at station 3 in December 2000 where biomass increased from 7.16g.m-2 recorded before trawling to 34.53 g.m-2 in the samples collected after trawling .Multivariate community analysis carried out based on both species abundance and biomass of plychaetes also confirm the wide variations in the similarities of the stations comparing both before and after trawling

Ecobiogeography, Spatial and Temporal Variations of Microzooplankton Along the East Coast of India

In the present study an attempt has been made to understand the microzooplankton community along the easr coast of India. Most of the earlier studies projected Bay of Bengal as an oligotrophic system where phytoplankton growth is limited by a number of factors among which nutrients are the foremost. Hence it is logical to consider that the most of the primary production in the Bay of Bengal could be contributed by small sized phytoplankton harnessing the available resources, which in turn can be utilized effiency by the microzooplankton only. Hence microzooplankton could play in transferring primary organic carbon to higher tropic levels in this region.

Studies on the Quality of Rainwater at Various Land Use Locations and Variations by Interaction with Domestic Rainwater Harvesting Systems

The present study focused on the quality of rainwater at various land use locations and its variations on interaction with various domestic rainwater harvesting systems.Sampling sites were selected based upon the land use pattern of the locations and were classified as rural, urban, industrial and sub urban. Rainwater samples were collected from the south west monsoon of May 2007 to north east monsoon of October 2008, from four sampling sites namely Kothamangalam, Emakulam, Eloor and Kalamassery, in Ernakulam district of the State of Kerala, which characterized typical rural, urban, industrial and suburban locations respectively. Rain water samples at various stages of harvesting were also collected. The samples were analyzed according to standard procedures and their physico-chemical and microbiological parameters were determined. The variations of the chemical composition of the rainwater collected were studied using statistical methods. It was observed that 17.5%, 30%, 45.8% and 12.1% of rainwater samples collected at rural, urban, industrial and suburban locations respectively had pH less than 5.6, which is considered as the pH of cloud water at equilibrium with atmospheric CO,.Nearly 46% of the rainwater samples were in acidic range in the industrial location while it was only 17% in the rural location. Multivariate statistical analysls was done using Principal Component Analysis, and the sources that inf1uence the composition of rainwater at each locations were identified .which clearly indicated that the quality of rain water is site specific and represents the atmospheric characteristics of the free fall The quality of harvested rainwater showed significant variations at different stages of harvesting due to deposition of dust from the roof catchment surface, leaching of cement constituents etc. Except the micro biological quality, the harvested rainwater satisfied the Indian Standard guide lines for drinking water. Studies conducted on the leaching of cement constituents in water concluded that tanks made with ordinary portland cement and portland pozzolana cement could be safely used for storage of rain water.

Characterization of rhodamine 6G doped polymer optical fiber by side illumination fluorescence

The length-dependent tuning of the fluorescence spectra of a dye doped polymer fiber is reported. The fiber is pumped sideways and the fluorescence is measured from one of the ends. The excitation of a finite length of dye doped fiber is done by a diode pumped solid state laser at a wavelength of 532 nm. The fluorescence emission is measured at various positions of the fiber starting from a position closer to the pumping region and then progressing toward the other end of the fiber. We observe that the optical loss coefficients for shorter and longer distances of propagation through the dye doped fiber are different. At longer distances of propagation, a decrease in optical loss coefficient is observed. The fluorescence peaks exhibit a redshift of 12 nm from 589 to 610 nm as the point of illumination progresses toward the detector end. This is attributed to the self-absorption and re-emission of the laser dye in the fiber.

Side illumination fluorescence emission characteristics from a dye doped polymer optical fiber under two-photon excitation.

Two-photon excited (TPE) side illumination fluorescence studies in a Rh6G-RhB dye mixture doped polymer optical fiber (POF) and the effect of energy transfer on the attenuation coefficient is reported. The dye doped POF is pumped sideways using 800 nm, 70 fs laser pulses from a Ti:sapphire laser, and the TPE fluorescence emission is collected from the end of the fiber for different propagation distances. The fluorescence intensity of RhB doped POF is enhanced in the presence of Rh6G as a result of energy transfer from Rh6G to RhB. Because of the reabsorption and reemission process in dye molecules, an effective energy transfer is observed from the shorter wavelength part of the fluorescence spectrum to the longer wavelength part as the propagation distance is increased in dye doped POF. An energy transfer coefficient is found to be higher at shorter propagation distances compared to longer distances. A TPE fluorescence signal is used to characterize the optical attenuation coefficient in dye doped POF. The attenuation coefficient decreases at longer propagation distances due to the reabsorption and reemission process taking place within the dye doped fiber as the propagation distance is increased.

Strategies for Inverse Profiling of Two Dimensional Dielectric Scatterers Using Electromagnetic Illumination

Electromagnetic tomography has been applied to problems in nondestructive evolution, ground-penetrating radar, synthetic aperture radar, target identification, electrical well logging, medical imaging etc. The problem of electromagnetic tomography involves the estimation of cross sectional distribution dielectric permittivity, conductivity etc based on measurement of the scattered fields. The inverse scattering problem of electromagnetic imaging is highly non linear and ill posed, and is liable to get trapped in local minima. The iterative solution techniques employed for computing the inverse scattering problem of electromagnetic imaging are highly computation intensive. Thus the solution to electromagnetic imaging problem is beset with convergence and computational issues. The attempt of this thesis is to develop methods suitable for improving the convergence and reduce the total computations for tomographic imaging of two dimensional dielectric cylinders illuminated by TM polarized waves, where the scattering problem is defmed using scalar equations. A multi resolution frequency hopping approach was proposed as opposed to the conventional frequency hopping approach employed to image large inhomogeneous scatterers. The strategy was tested on both synthetic and experimental data and gave results that were better localized and also accelerated the iterative procedure employed for the imaging. A Degree of Symmetry formulation was introduced to locate the scatterer in the investigation domain when the scatterer cross section was circular. The investigation domain could thus be reduced which reduced the degrees of freedom of the inverse scattering process. Thus the entire measured scattered data was available for the optimization of fewer numbers of pixels. This resulted in better and more robust reconstructions of the scatterer cross sectional profile. The Degree of Symmetry formulation could also be applied to the practical problem of limited angle tomography, as in the case of a buried pipeline, where the ill posedness is much larger. The formulation was also tested using experimental data generated from an experimental setup that was designed. The experimental results confirmed the practical applicability of the formulation.

A Study on Variations in Industrial Electricity Tariff & Regulatory Intervention in kerala State

Department of Applied Economics, Cochin University of Science and Technology

Studies on storm surges and sea level variations along the east coast of india

It became so usual for the east coast of India to face at least IO to 15 cyclones every year, out of which 3 to 4 may reach the deep depression stage. As a result the east coast of India experiences frequent heavy damages of varying intensities due to storm surges and it is also not unusual to experience a calamitous deluge once in a decade or so. Loss of life and damages can be minimized only if the magnitude of the surge could be predicted at least a day in advance. Therefore, an attempt to study the storm surges generated by the cyclones that strike the east coast of India and. suggest a method of predicting them through nomogram is made

Inter- State Variations in Productivity trends and Technological Change in Indian industry

The present study entitled ‘Inter-State Variations in Manufacturing Productivity and Technological Changes in India’ covers a period of 38 years from l960 tol998-99. The study is mainly based on ASI data. The study starts with a discussion of the major facilitating factors of industrialization, namely, historical forces, public policy and infrastructure facilities. These are discussed in greater details in the context of our discussion on Perrox’s (1998) ‘growth pole’ and ‘development pole’, Hirschman’s (1958) ‘industrial centers’ and Myrdal’s ‘spread effect’ Most of the existing literature more or less agrees that the process of industrialization has not been unifonn in all Indian states. There has been a decline in inter-state industrial disparities over time. This aspect is dealt at some length in the third chapter. An important element that deserves detailed attention is the intra-regional differences in industrialisation. Regional industrialisation implies the emergence of a few focal points and industrial regions. Calcutta, Bombay and Madras were the initial focal points. Later other centers like Bangalore, Amritsar, Ahemedabad etc. emerged as nodal points in other states. All major states account for focal points. The analysis made in the third chapter shows that industrial activities generally converge to one or two focal points and industrial regions have emerged out of the focal points in almost all states. One of the general features of these complexes and regions is that they approximately accommodate 50 to 75 percent of the total industrial units and workers in the state. Such convergence is seen hands in glow with urbanization. It was further seen that intra-regional industrial disparity comes down in industrial states like Maharashtra, Gujarat and Uttar Pradesh.

Variations of surface boundary layer parameters associated with Cyclone Gonu over the Arabian Sea using QuikSCAT data

This study attempted to quantify the variations of the surface marine atmospheric boundary layer (MABL) parameters associated with the tropical Cyclone Gonu formed over the Arabian Sea during 30 May–7 June 2007 (just after the monsoon onset). These characteristics were evaluated in terms of surface wind, drag coefficient, wind stress, horizontal divergence, and frictional velocity using 0.5◦ × 0.5◦ resolution Quick Scatterometer (QuikSCAT) wind products. The variation of these different surface boundary layer parameters was studied for three defined cyclone life stages: prior to the formation, during, and after the cyclone passage. Drastic variations of the MABL parameters during the passage of the cyclone were observed. The wind strength increased from 12 to 22 m s−1 in association with different stages of Gonu. Frictional velocity increased from a value of 0.1–0.6 m s−1 during the formative stage of the system to a high value of 0.3–1.4 m s−1 during the mature stage. Drag coefficient varied from 1.5 × 10−3 to 2.5 × 10−3 during the occurrence of Gonu. Wind stress values varied from 0.4 to 1.1 N m−2. Wind stress curl values varied from 10 × 10−7 to 45 × 10−7 N m−3. Generally, convergent winds prevailed with the numerical value of divergence varying from 0 to –4 × 10−5 s−1. Maximum variations of the wind parameters were found in the wall cloud region of the cyclone. The parameters returned to normally observed values in 1–3 days after the cyclone passage

Characterization of the molecular clockwork in the cockroach Rhyparobia maderae

Der Wechsel von Tag und Nacht erzeugt einen regelmäßigen Rhythmus von verschiedenen Umweltreizen, allen voran Licht und Temperatur. Fast jedes bis zum heutigen Tage untersuchte Lebewesen besitzt einen endogenen Mechanismus zur Zeitwahrnehmung, und diese "innere Uhr" befähigt Lebewesen dazu, sich vorausschauend an rhythmische Umwelt-Änderungen anzupassen. Circadiane Rhythmen bestehen auch ohne jegliche äußere Reize und basieren auf einem molekularen Rückkopplungs-Mechanismus, der Rhythmen in Genexpression und Proteinkonzentration von etwa 24 Stunden erzeugt. Obwohl sich die grundsätzlichen Mechanismen und Komponenten dieses molekularen Uhrwerks in allen Insekten ähneln, zeigte sich jedoch immer mehr, dass es im Detail doch wesentliche Unterschiede zwischen verschiedenen Insektengruppen gibt. Während das molekulare Uhrwerk der Fruchtfliege Drosophila melanogaster inzwischen sehr gut untersucht ist, fehlen bei den meisten Insektengruppen immernoch eingehende Untersuchungen. Fast nichts ist über die molekulare Basis von circadianen Rhythmen bei der Schabe Rhyparobia maderae bekannt, obwohl diese Art bereits seit Langem als Modellorganismus in der Chronobiologie dient. Um mit der Forschung am molekularen, circadianen System von R. maderae zu beginnen, wurde die Struktur und das Expressionsprofil der core feedback loop Gene per, tim1 und cry2 analysiert. Mittels degenerierten Primern und RACE konnte das vollständige offene Leseraster (OLR) von rmPer und rmCry2, und ein Teil des rmTim1 OLR kloniert werden. Eine phylogenetische Analyse gruppierte rmPER und rmCRY2 gemeinsam mit den Orthologa hemimetaboler Insekten. Viele bei D. melanogaster funktionell charakterisierte Domänen sind bei diesen Proteinen konserviert, was auf eine ähnliche Funktion in der inneren Uhr von R. maderae hinweist. Mittels quantitativer PCR konnte gezeigt werden, dass die mRNA von rmPer, rmTim1 und rmCry2 in verschiedenen Lichtregimen in der gleichen Phasenlage Tageszeit-abhängig schwankt. Die Phasenlage stellte sich bei unterschiedlichen Photoperioden jeweils relativ zum Beginn der Skotophase ein, mit Maxima in der ersten Hälfte der Nacht. Auch im Dauerdunkel zeigen sich Rhythmen in der rmTim1 und rmCry2 Expression. Die Amplitude der rmPer Expressionsrhythmen war jedoch so gering, dass keine signifikanten Unterschiede zwischen den einzelnen Zeitgeberzeiten (ZT) festgestellt werden konnten. Mittels Laufrad-Assays wurde untersucht wie Kurz- und Langtag Lichtregime die Verhaltensrhythmen beeinflussen. Es konnten nur Unterschiede in der Periodenlänge unter freilaufenden Bedingungen festgestellt werden, wenn höhere Lichtintensitäten (1000lx) zur Synchronisation (entrainment) genutzt wurden. Die Periode des freilaufenden Rhythmus war bei Tieren aus dem Kurztag länger. Die photoperiodische Plastizität zeigte sich also auch auf Verhaltensebene, obwohl höhere Lichtintensitäten notwendig waren um einen Effekt zu beobachten. Basierend auf den Sequenzen der zuvor klonierten OLR wurden gegen rmPER, rmTIM1 und rmCRY2 gerichtete Antikörper hergestellt. Die Antikörper gegen rmPER und rmTIM1 erkannten in western blots sehr wahrscheinlich spezifisch das jeweilige Protein. Zeitreihen von Gehirngewebe-Homogenisaten zeigten keinen offensichtlichen circadianen Rhythmus in der Proteinkonzentration, wahrscheinlich auf Grund einer Oszillation mit niedriger Amplitude. In Immunhistochemischen Färbungen konnte nur mit dem gegen rmPER gerichteten Antikörper aus Kaninchen ein Signal beobachtet werden. Beinahe jede Zelle des Zentralnervensystems war rmPER-immunreaktiv im Zellkern. Es konnten keine Unterschiede zwischen den untersuchten ZTs festgestellt werden, ähnlich wie bei den western blot Zeitreihen. In dieser Studie konnten erstmals molekulare Daten der circadianen Uhr von R. maderae erfasst und dargestellt werden. Die Uhrgene per, tim1 und cry2 werden in dieser Schabenart exprimiert und ihre Domänenstruktur sowie das circadiane Expressionsmuster ähneln dem hypothetischen ursprünglichen Insektenuhrwerk, welches der circadianen Uhr von Vertebraten nahesteht. Das molekulare Uhrwerk von R. maderae kann sich an unterschiedliche Photoperioden anpassen, und diese Anpassungen manifestieren sich im Expressionsprofil der untersuchten Uhrgene ebenso wie im Verhalten.

The prediction of seasonal and inter-annual climate variations and their impacts on the water resources in the eastern seaboard of Thailand

The research of this thesis dissertation covers developments and applications of short-and long-term climate predictions. The short-term prediction emphasizes monthly and seasonal climate, i.e. forecasting from up to the next month over a season to up to a year or so. The long-term predictions pertain to the analysis of inter-annual- and decadal climate variations over the whole 21st century. These two climate prediction methods are validated and applied in the study area, namely, Khlong Yai (KY) water basin located in the eastern seaboard of Thailand which is a major industrial zone of the country and which has been suffering from severe drought and water shortage in recent years. Since water resources are essential for the further industrial development in this region, a thorough analysis of the potential climate change with its subsequent impact on the water supply in the area is at the heart of this thesis research. The short-term forecast of the next-season climate, such as temperatures and rainfall, offers a potential general guideline for water management and reservoir operation. To that avail, statistical models based on autoregressive techniques, i.e., AR-, ARIMA- and ARIMAex-, which includes additional external regressors, and multiple linear regression- (MLR) models, are developed and applied in the study region. Teleconnections between ocean states and the local climate are investigated and used as extra external predictors in the ARIMAex- and the MLR-model and shown to enhance the accuracy of the short-term predictions significantly. However, as the ocean state – local climate teleconnective relationships provide only a one- to four-month ahead lead time, the ocean state indices can support only a one-season-ahead forecast. Hence, GCM- climate predictors are also suggested as an additional predictor-set for a more reliable and somewhat longer short-term forecast. For the preparation of “pre-warning” information for up-coming possible future climate change with potential adverse hydrological impacts in the study region, the long-term climate prediction methodology is applied. The latter is based on the downscaling of climate predictions from several single- and multi-domain GCMs, using the two well-known downscaling methods SDSM and LARS-WG and a newly developed MLR-downscaling technique that allows the incorporation of a multitude of monthly or daily climate predictors from one- or several (multi-domain) parent GCMs. The numerous downscaling experiments indicate that the MLR- method is more accurate than SDSM and LARS-WG in predicting the recent past 20th-century (1971-2000) long-term monthly climate in the region. The MLR-model is, consequently, then employed to downscale 21st-century GCM- climate predictions under SRES-scenarios A1B, A2 and B1. However, since the hydrological watershed model requires daily-scale climate input data, a new stochastic daily climate generator is developed to rescale monthly observed or predicted climate series to daily series, while adhering to the statistical and geospatial distributional attributes of observed (past) daily climate series in the calibration phase. Employing this daily climate generator, 30 realizations of future daily climate series from downscaled monthly GCM-climate predictor sets are produced and used as input in the SWAT- distributed watershed model, to simulate future streamflow and other hydrological water budget components in the study region in a multi-realization manner. In addition to a general examination of the future changes of the hydrological regime in the KY-basin, potential future changes of the water budgets of three main reservoirs in the basin are analysed, as these are a major source of water supply in the study region. The results of the long-term 21st-century downscaled climate predictions provide evidence that, compared with the past 20th-reference period, the future climate in the study area will be more extreme, particularly, for SRES A1B. Thus, the temperatures will be higher and exhibit larger fluctuations. Although the future intensity of the rainfall is nearly constant, its spatial distribution across the region is partially changing. There is further evidence that the sequential rainfall occurrence will be decreased, so that short periods of high intensities will be followed by longer dry spells. This change in the sequential rainfall pattern will also lead to seasonal reductions of the streamflow and seasonal changes (decreases) of the water storage in the reservoirs. In any case, these predicted future climate changes with their hydrological impacts should encourage water planner and policy makers to develop adaptation strategies to properly handle the future water supply in this area, following the guidelines suggested in this study.