Use of tomato and cucumber horticulture by-products in goat diets: effects o nrumen fermentation and microbial communities in batch and continuous cultures

Two in vitro experiments were conducted to analyse the effects of replacing dietary barley grain with wastes of tomato and cucumber fruits and a 1 : 1 tomato : cucumber mixture on rumen fermentation characteristics and microbial abundance. The control (CON) substrate contained 250 g/kg of barley grain on a dry matter (DM) basis, and another 15 substrates were formulated by replacing 50, 100, 150, 200 or 250 g of barley grain/kg with the same amount (DM basis) of tomato or cucumber fruits or 1 : 1 tomato : cucumber mixture. In Expt 1, all substrates were incubated in batch cultures with rumen micro-organisms from goats for 24 h. Increasing amounts of tomato, cucumber and the mixture of both fruits in the substrate increased final pH and gas production, without changes in final ammonia-nitrogen (NH3-N) concentrations, substrate degradability and total volatile fatty acid (VFA) production, indicating that there were no detrimental effects of any waste fruits on rumen fermentation. Therefore, in Expt 2 the substrates including 250 g of waste fruits (T250, C250 and M250 for tomato, cucumber and the mixture of both fruits, respectively) and the CON substrate were incubated in single-flow continuous-culture fermenters for 8 days. Total VFA production did not differ among substrates, but there were differences in VFA profile. Molar proportions of propionate, isobutyrate and isovalerate were lower and acetate : propionate ratio was greater for T250 compared with CON substrate. Fermentation of substrates containing cucumber (C250 and M250) resulted in lower proportions of acetate, isobutyrate and isovalerate and acetate : propionate ratio, but greater butyrate proportions than the CON substrate. Carbohydrate degradability and microbial N synthesis tended to be lower for substrates containing cucumber than for the CON substrate, but there were no differences between CON and T250 substrates. Abundance of total bacteria, Fibrobacter succinogenes and Ruminococcus flavefaciens, fungi, methanogenic archaea and protozoa were similar in fermenters fed T250 and CON substrates, but fermenters fed C250 and M250 substrates had lower abundances of R. flavefaciens, fungi and protozoa than those fed the CON substrate. Results indicated that tomato fruits could replace dietary barley grain up to 250 g/kg of substrate DM without noticeable effects on rumen fermentation and microbial populations, but the inclusion of cucumber fruits at 250 g/kg of substrate DM negatively affected some microbial populations as it tended to reduce microbial N synthesis and changed the VFA profile. More studies are needed to identify the dietary inclusion level of cucumber which produces no detrimental effects on rumen fermentation and microbial growth.

Comparison of fermentation characteristics and bacterial diversity in the rumen of sheep and batch cultures of rumen microorganisms

The objective of the current study was to assess how closely batch cultures (BC) of rumen microorganisms can mimic the dietary differences in fermentation characteristics found in the rumen, and to analyse changes in bacterial diversity over the in vitro incubation period. Four ruminally and duodenally cannulated sheep were fed four diets having forage : concentrate ratios (FCR) of 70 : 30 or 30 : 70, with either alfalfa hay or grass hay as forage. Rumen fluid from each sheep was used to inoculate BC containing the same diet fed to the donor sheep, and the main rumen fermentation parameters were determined after 24 h of incubation. There were differences between BC and sheep in the magnitude of most measured parameters, but BC detected differences among diets due to forage type similar to those found in sheep. In contrast, BC did not reproduce the dietary differences due to FCR found in sheep for pH, degradability of neutral detergent fibre and total volatile fatty acid (VFA) concentrations. There were differences between systems in the magnitude of most determined parameters and BC showed higher pH values and NH3–N concentrations, but lower fibre degradability and VFA and lactate concentrations compared with sheep. There were significant relationships between in vivo and in vitro values for molar proportions of acetate, propionate and butyrate, and the acetate : propionate ratio. The automated ribosomal intergenic spacer analysis (ARISA) of 16S ribosomal deoxyribonucleic acid showed that FCR had no effect on bacterial diversity either in the sheep rumen fluid used as inoculum (IN) or in BC samples. In contrast, bacterial diversity was greater with alfalfa hay diets than those with grass hay in the IN, but was unaffected by forage type in the BC. Similarity index between the bacterial communities in the inocula and those in the BC ranged from 67·2 to 74·7%, and was unaffected by diet characteristics. Bacterial diversity was lower in BC than in the inocula with 14 peaks out of a total of 181 detected in the ARISA electropherograms never appearing in BC samples, which suggests that incubation conditions in the BC may have caused a selection of some bacterial strains. However, each BC sample showed the highest similarity index with its corresponding rumen IN, which highlights the importance of using rumen fluid from donors fed a diet similar to that being incubated in BC when conducting in vitro experiments.

Flotação por ar dissolvido aplicado à separação de microalgas cultivadas em fotobiorreator, alimentado com vinhaça pré-tratada físico-quimicamente, com vistas à exploração de seu potencial bioenergético

Apesar de ser considerado um combustível sustentável, o etanol, produzido a partir da cana de açúcar, deixa um passivo de grandes proporções durante seu processo produtivo, a vinhaça, que vem sendo depositada nas próprias lavouras de cana de açúcar. É gerada na proporção de 12 litros para cada litro de etanol produzido em média, sendo rica em diversos nutrientes, os quais podem ser aproveitados para diversos fins como, por exemplo, meio de cultivo para microalgas. A presente pesquisa avaliou em uma primeira etapa a clarificação da vinhaça por um processo de coagulação com auxílio de um polímero catiônico, seguida de uma etapa de microfiltração tangencial em filtro de fibras ocas, o que permitiu uma redução superior a 77% para a cor aparente, de 99% para a turbidez e de 20% para a DQO, facilitando a utilização deste efluente para o cultivo de microalgas. Numa segunda etapa, foi avaliado o cultivo da microalga Chlorella vulgaris, em escala de bancada e operação em batelada, em meio preparado a partir da diluição da vinhaça em água de poço profundo, obtendo um aumento na biomassa produzida, determinado em termos de clorofila-a, em concentrações de vinhaça inferiores a 7,5% utilizando inóculo da ordem de 106 indivíduos. Tais dados permitiram a realização de ensaios de cultivo em escala contínua, com fotobiorreatores em escala piloto, gerando assim a biomassa utilizada nas próximas fases do estudo, que avaliaram a separação da biomassa gerada pelo processo de flotação por ar dissolvido. Os ensaios inicialmente realizados em escala de bancada e operados em batelada permitiram identificar as condições ótimas de operação, as quais foram então avaliadas em um flotador operando em fluxo contínuo. Tal flotador permitiu a obtenção de um lodo com teor de sólidos superior a 2%, o qual foi submetido à um processo final de desaguamento por centrifugação. Os ensaios de desaguamento, permitiram verificar que a utilização do mesmo polímero utilizado na etapa de clarificação permite a obtenção de um lodo mais estável, quando comparado com a não utilização de produto químico, na dosagem de polímero catiônico de 6 g.kg-1. A conclusão deste trabalho permitiu verificar a possibilidade de utilização da vinhaça como meio de cultivo de microalgas, reduzindo assim um dos impactos causados pela produção de etanol. Além disso foi possível verificar o potencial da FAD, para o espessamento de biomassa produzido em fotobiorreatores.

Degradação anaeróbia de fenol sob diferentes condições nutricionais

A tecnologia anaeróbia tem sido utilizada com sucesso no tratamento de água residuária contendo compostos fenólicos. Recentes pesquisas incluem tais compostos entre aqueles que podem ser degradados através desse processo. O objetivo desse trabalho foi avaliar a degradação do fenol em diferentes condições nutricionais, com ênfase na redução do sulfato. Os experimentos foram realizados com meio de cultura específico para esses microrganismos anaeróbios. Foram realizados ensaios de degradação em reatores em batelada alimentados nas seguintes condições: (1) fenol e sulfato, a diferentes concentrações, com inóculo previamente enriquecido; (2) fenol, sulfato e co-substratos e; (3) fenol, sulfato e extrato de levedura. Todos os ensaios foram realizados em temperatura de 30 graus Celsius, sob agitação de 150 rpm. Foi avaliado o consumo de fenol e sulfato e, produção de metano, em função do tempo, para diferentes concentrações iniciais de fenol e sulfato. Nos ensaios com reatores alimentados com fenol (329,3 mg/l); fenol (307,3 mg/l) e sulfato (160 mg/l); fenol (322.3 mg/l), sulfato (160 mg/l) e lactato (478,16 mg/l); fenol (332,1 mg/l), sulfato (150 mg/l) e etanol (129,76 mg/l), a remoção foi de, respectivamente, 99,8%, 98,2%, 98,8% e 98,8%. Os reatores alimentados com fenol (239,7 mg/l) obtiveram 100% de eficiência na degradação em apenas 11 dias e, os reatores alimentados com fenol (234,3 mg/l) e sulfato (162,5 mg/l) e fenol (256,0 mg/l) e sulfato (500 mg/l) tiveram eficiências de degradação de, respectivamente, 98,8% e 99,3% com 17 dias de operação. Tais eficiências foram obtidas pelo acréscimo de extrato de levedura nos reatores, no início dos ensaios. A caracterização morfológica foi realizada através de microscopia óptica. A diversidade microbiana referente aos Domínios Bacteria e Archaea, além do grupo de bactérias redutoras de sulfato foi avaliada através da técnica de PCR DGGE, onde foram observadas alterações nas populações microbianas, em função das condições nutricionais. Para o Domínio Archaea não foram observadas diferenças nos ensaios realizados. Para o Domínio Bacteria e Grupo das BRS essas diferenças foram, mais facilmente, percebidas com relação ao inóculo e entre os diversos reatores. A alteração na diversidade microbiana pode ter sido decorrente da composição do meio que, nesse caso, foi específico para BRS e a composição do inóculo que continha parte previamente adaptada às BRS. Essas condições adequadas puderam propiciar surgimento e desenvolvimento de populações microbianas capazes de degradar fenol, utilizando sulfato.

Water reduction in waste-activated sludge by resettling and filtration in batch. Phase (1): pilot-scale experiments to optimize performance

This article describes an effective procedure for reducing the water content of excess sludge production from a wastewater treatment plant by increasing its concentration and, as a consequence, minimizing the volume of sludge to be managed. It consists of a pre-dewatering sludge process, which is used as a preliminary step or alternative to the thickening. It is made up of two discontinuous sequential stages: the first is resettling and the second, filtration through a porous medium. The process is strictly physical, without any chemical additives or electromechanical equipment intervening. The experiment was carried out in a pilot-scale system, consisting of a column of sedimentation that incorporates a filter medium. Different sludge heights were tested over the filter to verify the influence of hydrostatic pressure on the various final concentrations of each stage. The results show that the initial sludge concentration may increase by more than 570% by the end of the process with the final volume of sludge being reduced in similar proportions and hydrostatic pressure having a limited effect on this final concentration. Moreover, the value of the hydrostatic pressure at which critical specific cake resistance is reached is established.

Use of stable-isotope probing, full-cycle rRNA analysis, and fluorescence in situ hybridization-microautoradiography to study a methanol-fed denitrifying microbial community

A denitrifying microbial consortium was enriched in an anoxically operated, methanol-fed sequencing batch reactor (SBR) fed with a mineral salts medium containing methanol as the sole carbon source and nitrate as the electron acceptor. The SBR was inoculated with sludge from a biological nutrient removal activated sludge plant exhibiting good denitrification. The SBR denitrification rate improved from less than 0.02 mg of NO3-.N mg of mixed-liquor volatile suspended solids (MLVSS)(-1) h(-1) to a steady-state value of 0.06 mg of NO3-.N mg of MLVSS-1 h(-1) over a 7-month operational period. At this time, the enriched microbial community was subjected to stable-isotope probing (SIP) with [C-13] methanol to biomark the DNA of the denitrifiers. The extracted [C-13]DNA and [C-12]DNA from the SIP experiment were separately subjected to full-cycle rRNA analysis. The dominant 16S rRNA gene phylotype (group A clones) in the [C-13]DNA clone library was closely related to those of the obligate methylotrophs Methylobacillus and Methylophilus in the order Methylophilales of the Betaproteobacteria (96 to 97% sequence identities), while the most abundant clone groups in the [C-12]DNA clone library mostly belonged to the family Saprospiraceae in the Bacteroidetes phylum. Oligonucleotide probes for use in fluorescence in situ hybridization (FISH) were designed to specifically target the group A clones and Methylophilales (probes DEN67 and MET1216, respectively) and the Saprospiraceae clones (probe SAP553). Application of these probes to the SBR biomass over the enrichment period demonstrated a strong correlation between the level of SBR denitrification and relative abundance of DEN67-targeted bacteria in the SBR community. By contrast, there was no correlation between the denitrification rate and the relative abundances of the well-known denitrifying genera Hyphomicrobium and Paracoccus or the Saprospiraceae clones visualized by FISH in the SBR biomass. FISH combined with microautoradiography independently confirmed that the DEN67-targeted cells were the dominant bacterial group capable of anoxic [C-14] methanol uptake in the enriched biomass. The well-known denitrification lag period in the methanol-fed SBR was shown to coincide with a lag phase in growth of the DEN67-targeted denitrifying population. We conclude that Methylophilales bacteria are the dominant denitrifiers in our SBR system and likely are important denitrifiers in full-scale methanol-fed denitrifying sludges.

A novel wastewater treatment process: Simultaneous nitrification, denitrification and phosphorus removal

Simultaneous nitrification and denitrification (SND) via the nitrite pathway and anaerobic-anoxic enhanced biological phosphorus removal (EBPR) are two processes that can significantly reduce the COD demand for nitrogen and phosphorus removal. The combination of these two processes has the potential of achieving simultaneous nitrogen and phosphorus removal with a minimal requirement for COD. A lab-scale sequencing batch reactor (SBR) was operated in alternating anaerobic-aerobic mode with a low dissolved oxygen concentration (DO, 0.5 mg/L) during the aerobic period, and was demonstrated to accomplish nitrification, denitrification and phosphorus removal. Under anaerobic conditions, COD was taken up and converted to polyhydroxyalkanoates (PHA), accompanied with phosphorus release. In the subsequent aerobic stage, PHA was oxidized and phosphorus was taken up to less than 0.5 mg/L at the end of the cycle. Ammonia was also oxidised during the aerobic period, but without accumulation of nitrite or nitrate in the system, indicating the occurrence of simultaneous nitrification and denitrification. However, off-gas analysis found that the final denitrification product was mainly nitrous oxide (N2O) not N-2. Further experimental results demonstrated that nitrogen removal was via nitrite, not nitrate. These experiments also showed that denitrifying glycogen.-accumulating organisms rather than denitrifying polyphosphate-accumulating organisms were responsible for the denitrification activity.

Enhanced biological phosphorus removal in a sequencing batch reactor using propionate as the sole carbon source

An enhanced biological phosphorus removal (EBPR) system was developed in a sequencing batch reactor (SBR) using propionate as the sole carbon source. The microbial community was followed using fluorescence in situ hybridization (FISH) techniques and Candidatus 'Accumulibacter phosphatis' were quantified from the start up of the reactor until steady state. A series of SBR cycle studies was performed when 55% of the SBR biomass was Accumulibacter, a confirmed polyphosphate accumulating organism (PAO) and when Candidatus 'Competibacter phosphatis,' a confirmed glycogen-accumulating organism (GAO), was essentially undetectable. These experiments evaluated two different carbon sources (propionate and acetate), and in every case, two different P-release rates were detected. The highest rate took place while there was volatile fatty acid (VFA) in the mixed liquor, and after the VFA was depleted a second P-release rate was observed. This second rate was very similar to the one detected in experiments performed without added VFA. A kinetic and stoichiometric model developed as a modification of Activated Sludge Model 2 (ASM2) including glycogen economy, was fitted to the experimental profiles. The validation and calibration of this model was carried out with the cycle study experiments performed using both VFAs. The effect of pH from 6.5 to 8.0 on anaerobic P-release and VFA-uptake and aerobic P-uptake was also studied using propionate. The optimal overall working pH was around 7.5. This is the first study of the microbial community involved in EBPR developed with propionate as a sole carbon source along with detailed process performance investigations of the propionate-utilizing PAOs. (C) 2004 Wiley Periodicals, Inc.

Concurrent microscopic observations and activity measurements of cellulose hydrolyzing and methanogenic populations during the batch anaerobic digestion of crystalline cellulose

This study compares process data with microscopic observations from an anaerobic digestion of organic particles. As the first part of the study, this article presents detailed observations of microbial biofilm architecture and structure in a 1.25-L batch digester where all particles are of an equal age. Microcrystalline cellulose was used as the sole carbon and energy source. The digestions were inoculated with either leachate from a 220-Lanaerobic municipal solid waste digester or strained rumen contents from a fistulated cow. The hydrolysis rate, when normalized by the amount of cellulose remaining in the reactor, was found to reach a constant value 1 day after inoculation with rumen fluid, and 3 days after inoculating with digester leachate. A constant value of a mass specific hydrolysis rate is argued to represent full colonization of the cellulose surface and first-order kinetics only apply after this point. Additionally, the first-order hydrolysis rate constant, once surfaces were saturated with biofilm, was found to be two times higher with a rumen inoculum, compared to a digester leachate inoculum. Images generated by fluorescence in situ hybridization (FISH) probing and confocal laser scanning microscopy show that the microbial communities involved in the anaerobic biodegradation process exist entirely within the biofilm. For the reactor conditions used in these experiments, the predominant methanogens exist in ball-shaped colonies within the biofilm. (C) 2005 Wiley Periodicals, Inc.

Plasma delipidation process induces rapid regression of atherosclerosis and mobilisation of adipose tissue

Cholesterol is a major component of atherosclerotic plaques. Cholesterol accumulation within the arterial intima and atherosclerotic plaques is determined by the difference of cellular cholesterol synthesis and/or influx from apo B-containing lipoproteins and cholesterol efflux. In humans, apo A-I Milano infusion has led to rapid regression of atherosclerosis in coronary arteries. We hypothesised that a multifunctional plasma delipidation process (PDP) would lead to rapid regression of experimental atherosclerosis and probably impact on adipose tissue lipids. In hyperlipidemic animals, the plasma concentrations of cholesterol, triglyceride and phospholipid were, respectively, 6-, 157-, and 18-fold higher than control animals, which consequently resulted in atherosclerosis. PDP consisted of delipidation of plasma with a mixture of butanol-diisopropyl ether (DIPE). PDP removed considerably more lipid from the hyperlipidemic animals than in normolipidemic animals. PDP treatment of hyperlipidemic animals markedly reduced intensity of lipid staining materials in the arterial wall and led to dramatic reduction of lipid in the adipose tissue. Five PDP treatments increased apolipoprotein A1 concentrations in all animals. Biochemical and hematological parameters were unaffected during PDP treatment. These results show that five PDP treatments led to marked reduction in avian atherosclerosis and removal of lipid from adipose tissue. PDP is a highly effective method for rapid regression of atherosclerosis.

Differential distribution of ammonia- and nitrite-oxidising bacteria in flocs and granules from a nitrifying/denitrifying sequencing batch reactor

A lab-scale sequencing batch reactor was operated with alternating anoxic/aerobic conditions for nitrogen removal. Flocs and granules co-existed in the same reactor, with distinct aggregate structure and size, for over 180 days of reactor operation' Process data showed complete nitrogen removal, with temporary nitrite accumulation before full depletion of ammonia in the aerobic phase. Microbial quantification of the biomass by fluorescence in situ hybridisation showed that granules contained most of the nitrite-oxidising bacteria (NOB) whereas the ammonium-oxidising bacteria (AOB) seemed to be more abundant in the flocs. This was supported by microsensor measurements, which showed a higher potential of NO2- uptake than NH4 uptake in the granules. The segregation is possibly linked to the different growth rates of the two types of nitrifiers and the reactor operational conditions, which produced different sludge retention time for flocs and granules. The apparent physical separation of AOB and NOB in two growth forms could potentially affect mass transfer of NO2- from AOB to NOB, but the data presented here shows that it did not impact negatively on the overall nitrogen removal. (c) 2006 Elsevier Inc. All rights reserved.

Competition between polyphosphate and glycogen accumulating organisms in enhanced biological phosphorus removal systems with acetate and propionate as carbon sources

Enhanced biological phosphorus removal (EBPR) is a widely used process for achieving phosphorus removal from wastewater. A potential reason for EBPR failure is the undesirable growth of glycogen accumulating organisms (GAOs), which can compete for carbon sources with the bacterial group responsible for phosphorus removal from wastewater: the polyphosphate accumulating organisms (PAOs). This study investigates the impact of carbon source on EBPR performance and the competition between PAOs and GAOs. Two sequencing batch reactors (SBRs) were operated during a 4-6 month period and fed with a media containing acetate or propionate, respectively, as the sole carbon source. It was found that the acetate fed SBR rarely achieved a high level of phosphorus removal, and that a large portion of the microbial community was comprised of Candidatus Competibacter phosphatis, a known GAO. The propionate fed SBR, however, achieved stable phosphorus removal throughout the study, apart from one brief disturbance. The bacterial community of the propionate fed SBR was dominated by Candidatus Accumulibacter phosphatis, a known PAO, and did not contain Competibacter In a separate experiment, another SBR was seeded with a mixture of PAOs and a group of alphaproteobacterial GAOs, both enriched with propionate as the sole carbon source. Stable EBPR was achieved and the PAO population increased while the GAOs appeared to be out-competed. The results of this paper suggest that propionate may provide PAOs with a selective advantage over GAOs in the PAO-GAO competition, particularly through the minimisation of Competibacter Propionate may be a more suitable substrate than acetate for enhancing phosphorus removal in EBPR systems. (c) 2005 Elsevier B.V. All rights reserved.

Identifying causes for N2O accumulation in a lab-scale sequencing batch reactor performing simultaneous nitrification, denitrification and phosphorus removal

The recently described process of simultaneous nitrification, denitrification and phosphorus removal (SNDPR) has a great potential to save capital and operating costs for wastewater treatment plants. However, the presence of glycogen-accumulating organisms (GAOs) and the accumulation of nitrous oxide (N2O) can severely compromise the advantages of this process. In this study, these two issues were investigated using a lab-scale sequencing batch reactor performing SNDPR over a 5-month period. The reactor was highly enriched in polyphosphate-accumulating organisms (PAOs) and GAOs representing around 70% of the total microbial community. PAOs were the dominant population at all times and their abundance increased, while GAOs population decreased over the study period. Anoxic batch tests demonstrated that GAOs rather than denitrifying PAOs were responsible for denitrification. NO accumulated from denitrification and more than half of the nitrogen supplied in a reactor cycle was released into the atmosphere as NO. After mixing SNDPR sludge with other denitrifying sludge, N2O present in the bulk liquid was reduced immediately if external carbon was added. We therefore suggest that the N2O accumulation observed in the SNDPR reactor is an artefact of the low microbial diversity facilitated by the use of synthetic wastewater with only a single carbon source. (C) 2005 Elsevier B.V. All rights reserved.

Neural control of a batch distillation

The purpose of the work reported here was to investigate the application of neural control to a common industrial process. The chosen problem was the control of a batch distillation. In the first phase towards deployment, a complex software simulation of the process was controlled. Initially, the plant was modelled with a neural emulator. The neural emulator was used to train a neural controller using the backpropagation through time algorithm. A high accuracy was achieved with the emulator after a large number of training epochs. The controller converged more rapidly, but its performance varied more widely over its operating range. However, the controlled system was relatively robust to changes in ambient conditions.

Inventory parameter management and focused continuous improvement for repetitive batch manufacturers

What this thesis proposes is a methodology to assist repetitive batch manufacturers in the adoption of certain aspects of the Lean Production principles. The methodology concentrates on the reduction of inventory through the setting of appropriate batch sizes, taking account of the effect of sequence dependent set-ups and the identification and elimination of bottlenecks. It uses a simple Pareto and modified EBQ based analysis technique to allocate items to period order day classes based on a combination of each item's annual usage value and set-up cost. The period order day classes the items are allocated to are determined by the constraints limits in the three measured dimensions, capacity, administration and finance. The methodology overcomes the limitations associated with MRP in the area of sequence dependent set-ups, and provides a simple way of setting planning parameters taking this effect into account by concentrating on the reduction of inventory through the systematic identification and elimination of bottlenecks through set-up reduction processes, so allowing batch sizes to reduce. It aims to help traditional repetitive batch manufacturers in a route to continual improvement by: Highlighting those areas where change would bring the greatest benefits. Modelling the effect of proposed changes. Quantifying the benefits that could be gained through implementing the proposed changes. Simplifying the effort required to perform the modelling process. It concentrates on increasing flexibility through managed inventory reduction through rationally decreasing batch sizes, taking account of sequence dependent set-ups and the identification and elimination of bottlenecks. This was achieved through the development of a software modelling tool, and validated through a case study approach.