Biochemical variation during ovarian vitellogenic growth in a hill stream teleost Garra mullya (Sykes) due to cadmium toxicity

Some biochemical variations during ovarian vitellogenic growth in hill-stream teleost Garra mullya due to sublethal concentration of cadmium has been discussed. Total protein, cholesterol and glycogen in ovary and liver along with gonadosomatic index (GSI) and hepatosomatic index (HSI) in Cd-treated fish exhibited significant decrease while liver glycogen remained unaltered.

A case study of the disappearance of Arius tenuispinis (marine catfish) in the vicinity of Visakhapatnam due to mechanised fishing

Visakhapatnam is on the eastern sea board of India (17 degree 40' N and 83 degree 15' E) having a continental shelf of 45 km width which is provided with a polychaete rich, silty clay sea floor to a distance of 15 km and beyond, from the shore. Repeated trawling by a large number of trawlers over an area of 900 sq.km (30 x 30) resulted in the hardening of the substratum to the extent of making it uninhabitable to the polychaetes and polychaete feeding fish. The shoaling and strictly demersal marine catfish, Arius tenuispinis, which is a prolific polychaete feeder on the fishing grounds off Visakhapatnam, has been on the decline since 1979. The catch rate of fish dropped from 9.7 kg/boat per day in 1979 to 2.6 kg by 1985-86. In the bottomset gillnets, the catch per net dwindled from 4.4 kg in 1973 to 0.04 kg by 1985-86. The species has virtually disappeared from the fishing grounds off Visakhapatnam and further north, as a results of the cumulative effect of overfishing with trawlnets and bottomset gillnets. It is further aggravated by the hardening of the sea floor on these grounds due to repeated trawling over a narrow zone.

THEORETICAL ROAD DAMAGE DUE TO DYNAMIC TYRE FORCES OF HEAVY VEHICLES. PART 1: DYNAMIC ANALYSIS OF VEHICLES AND ROAD SURFACES.

Theory is presented for simulating the dynamic wheel forces generated by heavy road vehicles and the resulting dynamic response of road surfaces to these loads. Sample calculations are provided and the vehicle simulation is validated with data from full-scale tests. The methods are used in the accompanying paper to simulate the road damage done by a tandem-axle vehicle.

THEORETICAL ROAD DAMAGE DUE TO DYNAMIC TYRE FORCES OF HEAVY VEHICLES. PART 2: SIMULATED DAMAGE CAUSED BY A TANDEM-AXLE VEHICLE.

The literature relating to road surface failure and design is briefly reviewed and the conventional methods for assessing the road damaging effects of dynamic tire forces are examined. A new time domain technique for analyzing dynamic tire forces and four associated road damage criteria are presented. The force criteria are used to examine the road damaging characteristics of a simple tandem-axle vehicle model for a range of speed and road roughness conditions. It is concluded that for the proposed criteria, the theoretical service life of road surfaces that are prone to fatigue failure may be reduced significantly by the dynamic component of wheel forces. The damage done to approximately five per cent of the road surface area during the passage of a theoretical model vehicle at typical highway speeds may be increased by as much as four times.

Road damage due to dynamic tyre forces measured on a public road

This paper describes a series of tests conducted on a UK trunk road, in which the dynamic tyre forces generated by over 1500 heavy goods vehicles (HGVs) were measured using a load measuring mat containing 144 capacitive strip sensors. The data was used to investigate the relative road damaging potential of the various classes of vehicles, and the degree of spatial repeatability of tyre forces present in a typical highway fleet. Approximately half the vehicles tested were found to contribute to a spatially repeatable pattern of pavement loading. On average, air suspended vehicles were found to generate lower dynamic load coefficients than steel suspended vehicles. However, air suspended vehicles also generated higher mean levels of theoretical road damage (aggregate force) than steel suspended vehicles, indicating that the ranking of suspensions depends on the pavement damage criterion used.

Quality loss in prawns due to double freezing

Icing is the practice for preserving prawns on board fishing boats in India. Majority of these boats need to preserve the catch only for a few hours because of the short duration of the fishing trip. However, with the anticipated introduction of a considerable number of bigger fishing vessels which can remain in the fishing ground for longer periods, more than fortnight, preservation methods, other than icing are required to retain prime quality. Freezing and cold storage of whole prawns on board followed by thawing and processing on land is a possible proposition. The extent of quality loss in prawns during these operations is one of the important points to be considered. Hence, laboratory scale studies were undertaken on double freezing of prawns and the results are dealt within this communication.

The seasonal variations of sea level due to density variations in the Arabian Gulf and Gulf of Oman

From the distribution of oceanographic data (temperature and salinity) in both Arabian Gulf and Gulf of Oman, the steric components (thermal, haline and steric heights) are calculated for the upper 50m layer during different seasons. The analysis reveals relevant evidence, that temperature variations (thermal component) play a role in the fluctuations of sea level within the investigated area. The salinity variations (haline component) is only significant near the entrance. The sea level variations due to density (steric component) is low during winter and spring and high during summer and autumn. The steric height is always lower in the northern and central regions of Arabian Gulf and higher in eastern region of Arabian Gulf and in the Gulf of Oman, i.e. the surface water must flow from the Gulf of Oman to the Arabian Gulf. The steric sea level gradient around the Strait of Hormuz are 0.04 cm/km in winter, 0.04 cm/km in spring, and 0.025 cm/km in summer and 0.014 cm/km in autumn.

Building damage and repair due to leakage in a deep excavation

The north-south line in Amsterdam is being built underneath the historic centre of the city. Three deep stations are being constructed in deep excavations supported by diaphragm walls. During the excavation for Vijzelgracht station, leakage through the wall resulted in large settlements and damage to historic buildings, which threatened continuation of the project. The authors analysed the cause of the leakage and the damage to the buildings. With the application of robust preventative measures at two of the deep excavations it was possible to continue the project. This paper reports on the cause of the events, the damage to the buildings and the counter-measures taken. It includes lessons learned for the project and for the foundations industry.

Effect of bend orientation on life and puncture point location due to solid particle erosion of a high concentration flow in pneumatic conveyors

An investigation into predicting failure of pneumatic conveyor pipe bends due to hard solid particle impact erosion has been carried out on an industrial scale test rig. The bend puncture point locations may vary with many factors. However, bend orientation was suspected of being a main factor due to the biased particle distribution pattern of a high concentration flow. In this paper, puncture point locations have been studied with different pipe bend orientations and geometry (a solids loading ratio of 10 being used for the high concentration flow). Test results confirmed that the puncture point location is indeed most significantly influenced by the bend orientation (especially for a high concentration flow) due to the biased particle distribution and biased particle flux distribution. © 2004 Elsevier B.V. All rights reserved.

CHANGES IN PREDICTED MOS DEVICE CHARACTERISTICS DUE TO THE USE OF TWO DIMENSIONAL SOURCE/DRAIN PROFILES.

Two-dimensional MOS device simulation programs such as MINIMOS left bracket 1 right bracket are limited in their validity due to assumptions made in defining the initial two-dimensional source/drain profiles. The two options available to define source/drain regions both construct a two-dimensional profile from one-dimensional profiles normal to the surface. Inaccuracies in forming these source/drain profiles can be expected to effect predicted device characteristics as channel dimensions of the device are reduced. This paper examines these changes by interfacing numerically similated two dimensional source/drain profiles to MINIMOS and comparing predicted I//D-V//D characteristics with 2-D interfacing, 2-D profiles constructed from interfaced 1-D profiles and MINIMOS self generated profiles. Data obtained for simulations of 3 mu m N and P channel devices are presented.