Avaliação qualitativa e quantitativa na deposição de calda de pulverização em Commelina benghalensis

O objetivo deste estudo foi o de avaliar a quantidade e qualidade da deposição da calda de pulverização em plantas de Commelina benghalensis, considerando os volumes de aplicação, as pontas de pulverização e o ângulo dos bicos na barra de pulverização. Foram utilizadas cinco hastes de plantas por vaso. O delineamento experimental adotado foi o inteiramente casualizado, com 20 repetições. O experimento foi conduzido em casa de vegetação e a aplicação da calda foi efetuada após 40 dias do transplantio das hastes, quando estavam com 30 a 40 cm de comprimento. Os tratamentos foram constituídos por cinco pontas de pulverização (TX-VK 6, TX-VK 8, XR 11001 VS, XR 11002 VS e TJ60 11002 VS), sendo testadas com dois ângulos de aplicação (0º e +30º), exceto a TJ60 11002 VS, e todas com dois volumes de calda distintos (100 e 200 L ha-1). Foi utilizado como traçador o corante Azul Brilhante FDC-1 na concentração de 500 ppm, para determinar a deposição da calda de pulverização. Após a aplicação, 20 hastes no total foram imediatamente coletadas e, em seguida, lavadas em 100 mL de água destilada, para posterior quantificação do traçador em espectrofotômetro. Os dados foram transformados em valores de depósitos por grama de massa seca e ajustados à curva de regressão pelo modelo de Gompertz. Os resultados evidenciaram que, independentemente da ponta utilizada, o volume de 200 L ha-1 proporcionou os maiores depósitos médios e pontuais nas plantas. Quanto à uniformidade do depósito de calda sobre as plantas, a ponta XR 11001 VS no volume de 100 L ha-1 proporcionou a melhor uniformidade. Contudo, quando se utilizou o ângulo de +30º, ocorreram acréscimos dos depósitos ao se utilizar o volume de 100 L ha-1, e, nesse caso, houve melhor uniformidade para o volume de 200 L ha-1.

Espectro de gotas de pontas de pulverização com adjuvantes de uso agrícola

O sucesso de uma boa aplicação de produtos fitossanitários depende da sinergia entre fatores como tamanho de gota, tipo de ponta, pressão, volume e composição da calda e características do alvo. Assim, o objetivo deste trabalho foi avaliar o espectro de gotas produzidas por pontas de jato plano defletor (TT 11002) e jato plano defletor com indução de ar (TTI 11002), com diferentes adjuvantes adicionados à calda de pulverização, pela técnica de difração de raio laser. O experimento foi conduzido em delineamento inteiramente casualizado, com quatro repetições, em esquema fatorial 2 x 5, ou seja, duas pontas de aplicação (jato plano defletor e jato plano defletor com indução de ar) e cinco composições de calda (água e água mais quatro adjuvantes: fosfatidilcoline+ácido propiônico, éter poliglicólico de monilfenol, ésteres de ácidos graxos e nonil-fenol etoxilado+óxido de etileno). em ambiente controlado, avaliou-se o espectro de gotas, por meio de um analisador a laser de gotas em tempo real, na pressão de 276 kPa. O efeito dos adjuvantes no espectro de gotas mostrou-se dependente da ponta de pulverização empregada. A adição dos adjuvantes à calda não alterou o risco potencial de deriva, expresso pela porcentagem do volume em gotas com diâmetro inferior a 100 µm, porém o adjuvante fosfatidilcoline+ácido propiônico reduziu o diâmetro da mediana volumétrica das gotas produzidas pela ponta de jato plano defletor com indução de ar, em relação à avaliação feita somente com água.

Natural latex graft in lamellar and penetrating sclerectomies in rabbits

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sol-gel synthesis of titania-alumina catalyst supports

Titanium oxide is a good candidate as new support for hydrotreating (HDT) catalysts, but has the inconvenience of presenting small surface area and poor thermal stability. To overcome these handicaps TiO2-Al2O3 mixed oxides were proposed as catalyst support. Here, the results concerning the preparation, characterization and testing of molybdenum catalyst supported on titania-alumina are presented. The support was prepared by sol-gel route using titanium and aluminum isopropoxides, chelated with acetylacetone (acac) to promote similar hydrolysis ratio for both the alcoxides. The effect of nominal complexing ratios [acac]/[Ti] and of sol aging temperature on the structural features of nanometric particles was analyzed by quasi-elastic light scattering (QELS) and N-2 adsorption isotherm measurements. These characterizations have shown that the addition of acac and the increase of aging temperature favor the full dispersion of primary nanoparticles in mother acid solution. The dried powder presents a monomodal distribution of slit-shaped micropores, formed by irregular packing of platelet primary particles, surface area superior to 200 m(2) g(-1) and mean pore size of about 1 nm. These characteristics of porous texture are preserved after firing at 673 K. The diffraction patterns of sample fired above 973 K show only the presence of anatase crystalline phase. The crystalline structure of the support remained unaltered after molybdenum adsorption, but the surface area and the micropore volume were drastically reduced. (C) 2002 Published by Elsevier B.V. B.V.

Use of topical mitomycin C in myoplasty of the medial rectus muscle of rabbits

To possibly reduce postoperative adhesions that occur after ocular myoplasties, we investigated the topical effects of 0.04% mitomycin C on the repaired areas of the medial rectus muscle using an equine renal capsule preserved in 98% glycerin for reinforcement of the sutures. Twenty-four rabbits, divided into two groups of 12 animals each [untreated (control) and treated group (MMC)], were submitted to surgical rupture of the medial rectus muscle of one eye and repair of the defect 24 h later with sutures and an equine renal capsule. Post-operative prophylactic treatment of the two groups consisted of the administration of eye drops containing neomycin, polymyxin B and dexamethasone at regular 6-h intervals for eight consecutive days and daily rinsing with physiological saline. MMC animals received additional treatment with topical 0.04% mitomycin C every 6 h for 14 consecutive days. Slit lamp biomicroscopy showed greater irritation of the ocular surface in MMC animals during the first days post operatively. Adhesions were observed at 15 and 30 days of assessment in the two groups, but were more extensive in control animals at 60 days. Histopathology revealed inflammatory exudation in both groups, which was greater in MMC animals. Mitomycin C (0.04%) instilled at 6-h intervals for 14 consecutive days reduced the occurrence of fibrosis in the myoplastic areas. However, the equine renal capsule was found to be of little benefit for the reinforcement of myoplasties.

Evaluation of cutting patterns produced in primary teeth by an air-abrasion system

Objective: the aim of this in vitro study was to assess the effect of tip diameter, nozzle distance, and application time of an air-abrasion system for cavity preparation on the enamel of primary teeth. Method and materials: Forty exfoliated primary teeth were air abraded with a microabrasion machine used with a handpiece with an 80-degree-angle nozzle, 50-mum abrasive particle size, and 80-psi air pressure. The effects of 0.38- or 0.48-mm inner tip diameter, 2- or 5-mm distance from tip to tooth surface, and 15 or 30 seconds of application time on cutting efficiency were evaluated. Cutting width and depth were analyzed and measured from scanning electron micrographs. Results: Statistical analysis revealed that the width of the cuts was significantly greater when the tip distance was increased. Significantly deeper cavities were produced by a tip with a 0.48-mm inner diameter. The application time did not influence the cuts. Conclusion: the cutting patterns found in this study suggest that precise removal of enamel in primary teeth is best accomplished when a tip with a 0.38-mm inner diameter is used at a 2-mm distance.

Effect of handpiece tip design on the cutting efficiency of an air abrasion system

Purpose : the aim of this study was to evaluate the effect of nozzle angle and tip diameter on the cutting efficiency of an air abrasion system. Materials and Methods: Thirty-six extracted human third molars were air-abraded with the PrepStar microabrasion machine using a handpiece with either 80degrees or 45degrees nozzle angles with 0.38 or 0.48 nun tip orifice diameters. The following parameters were held constant: abrasive particle size (27 mum), air pressure (80 psi), distance (2 mm.) and duration (15 seconds). The cutting efficiency was compared using enamel, dentin and cementum substrates. Width and depth of the cutting patterns were analyzed and measured using scanning electron micrographs. Results: Statistical analysis using three-way ANOVA and Duncan's Multiple Range test revealed that the width of the cuts was significantly greater when the cavities were prepared using the 45degrees nozzle angle. Significantly deeper cavities were produced with the 80degrees nozzle angle. The tip orifice of the nozzle influenced the cutting efficiency in softer substrates, dentin and cementum. Precise removal of hard tissue is best accomplished using the 80degrees angle nozzle tips for all types of tooth surfaces, enamel, dentin and cementum.

The gas flow rate increase obtained by an oscillating piezoelectric actuator on a micronozzle

Micronozzles with piezoelectric actuator were fabricated and investigated. The micronozzles were fabricated in glass substrates using a powder-blasting technique, and the actuator is a bimorph structure made from a piezoelectric polymer. The actuator was located at the nozzle outlet, and was driven in an oscillating mode by applying an alternating voltage across the actuator electrodes. With a pressure difference between inlet and outlet, the gas flow rate through the device was increased. This effect was quantified, and compared to a similar micronozzle with no actuator. The increase in the flow rate was defined as the gas flow through the micronozzle with actuator oscillating minus the gas flow without actuator, was found to depend on the inlet pressure, the pressure ratio, and the nozzle throat diameter. (C) 2008 Elsevier B.V. All rights reserved.

The minimum quantity of lubricant (MQL) technique in the surface grinding of steel

This research aimed to analyze the viability of the minimum quantity of lubricant (MQL) technique towards different methods of lubri-refrigeration in surface grinding of steel, considering process quality, wheel life and the viability of using cutting fluids The proposal methods were the conventional (abundant fluid flow), the minimum quantity lubrication (MQL) and the optimized method with Webster nozzle (rounded) This analysis was carried out in equal machining conditions, through the assessment of variables such as grinding force, surface roughness, G ratio (volume of removed material/volume of wheel wear), and microhardness The results showed the possibility of improvement of the grinding process Besides, there is the opportunity for production of high quality workpieces with lower costs The MQL technique showed efficiency in machining with lower depths of cut The optimized method with Webster nozzle applies the fluid in a rational way, without considerable waste Hence, the results show that industry can rationalize and optimize the application of cutting fluids, avoiding inappropriate disposal, inadequate use and consequently environment pollution

Pore structure characterization of kaolin, metakaolin, and their acid-treated products using small-angle X-ray scattering

Pore structure of dealuminated kaolin and metakaolin was studied by small-angle X-ray scattering (SAXS). Both parent kaolin and metakaolin have about 10% of the total pore volume provided by globular pores with 105 Å mean pore size. Their surface area is about 14 m2/g. Acid dealumination of kaolin causes an increase of its globular pore volume without an appreciable change in the mean pore size, its surface area increasing up to about 90 m2/g. Acid dealumination of metakaolin enhances the globular pore volume, although there is generation of slit-shaped pores with a narrow thickness distribution whose mean value is 14 Å. This interlayer spacing causes an increase in surface area of about 190 m2/g by SAXS. © 1994.

Padrões de distribuição de líquidos obtidos com bicos TF-VS4, TJ60-11006 e TQ15006 em mesa de prova

The performance of a spray boom can be evaluated from its individual nozzle distribution patterns determined in a patternator (test table), as discussed by Perecin et al. (1994). The distribution pattern of three nozzle types obtained in a patternator at six heights were compared in order to propose a formula for determining the variation coefficient. The simulation of a spray boom was conducted from individual nozzle distribution patterns, and obtained the random variation coefficients (RVC) and the systematic variation coefficients (SVC). The results showed good performance of the TF-SV4 nozzles, with CV smaller than 10%, for nozzle spacing as large as 50 cm. The TQ15006 nozzles showed high variability in the central region of the distribution pattern, resulting in high CV from nozzle spacings as narrow as 25 cm. The TJ60-11006 behaved as intermediate between TF-VS4 and TQ15006. The formula proposed for determining the variation coefficient is [(RVC) 2+(SVC) 2] 1/2.

Efficiency of safety measures applied to a manual knapsack sprayer for paraquat application to Maize (Zea mays L.)

The objectives of the present study were to evaluate the safety of mixer/loaders and applicators of paraquat to maize crop by knapsack sprayers and to determine the efficacy of safety measures applied to the sprayers. Potential dermal exposure (PDE) was evaluated in 22 worker body parts. The Cu2+ cation of a copper-based fungicide was used as tracer in the spray solution. Sanitary pads and cotton gloves were used to collect the pesticide solution on the sampled body parts. It was observed that paraquat application in front of the applicator's body (0.5 and 1.0 m lance) is unsafe because PDE was 1,979.8 ml/day (for 0.5 m lance) and 1,290.4 ml/day (for 1.0 m lance) and needs 50-80% and 37-69% control of PDE respectively. Control can be achieved by the use of protective garment on the legs and feet only, which received 92-93% of the PDE. Switching the spray nozzle to the back of the operator reduced the PDE by 98% and was sufficient to make working conditions safe, while maintaining the efficiency of application and making the work lighter and more comfortable. Mixer/loaders received 86% of the PDE to the hands and the work condition was safe (MOS > 1), however impermeable gloves could be used as a further safety measure.

Evaluation of cutting patterns produced with air-abrasion systems using different tip designs.

This study assessed cavity preparations produced with different air abrasion tip parameters. Twelve test groups of extracted teeth were prepared to evaluate the parameters of 80 degrees or 45 degrees nozzle angles and 0.38 or 0.48 mm inner tip diameters. All other factors were held constant. A device was made to hold the specimen and air abrasion handpiece that standardized the distance and position relative to the tooth and time of application. The cavities were evaluated by assessing the rounding of the cavosurface margins and cavity floor. Measurements of cavosurface angles and the angle of concavity were made at the deepest portion of the abraded surface using scanning electron micrographs. The cavosurface angles were compared using paired t-test, and the effects of the tip design parameters were analyzed by ANOVA and Duncan's Multiple Range test. From the cavity patterns found in this study, the authors suggest that 80 degrees angle tips are more appropriate than 45 degrees angle tips for making narrow, deep cuts for preventive resin restorations. Conversely, when shallow preparations are needed, as in the case of Class V cavity preparations, cutting patterns of 45 degrees angle tips are more suitable.

Ultramorphology and histology of dorsal vessel - Gastral portion - Of Camponotus rufipes

The dorsal diaphragm of Camponotus rufipes (Hymenoptera: Formicidae) is a thin membrane structure, with free edges between the points of attachment to the body wall that almost cover the whole extension of the dorsal vessel at its abdominal portion. A layer of fat body cells covers the region of the cuticle above the dorsal vessel and the incurrent ostia can be a vertical or horizontal slit in the wall of the heart. One organized structure as a network ofalary muscles was observed holding the heart at its middorsal position and supporting the pericardial cells too. A great number of pericardial cells were found laterally associated with the heart and cellular projections from those cells insert directly into the heart wall.

Características da pulverização produzida por pontas Yamaho da série 'D'

This study evaluated the characteristics of spray produced by Yamaho nozzle tip'D'series. The droplet size of nozzle tips D3, D4, D5, D6 and D8 were evaluated at 703, 1.050, 1.406, 1.758, 2.110, 2.461 e 2.813 kPa pressures (100, 200, 250; 350, e 400 psi) by means of laser equipment, as well as the flow rate of nozzle tip at the pressures of 702, 1.125, 1.406, 1.828, 2.110, 2.532 e 2.813 kPa (100, 160, 200, 260,300; 360 e 400 psi) which were compared with values indicated by manufacturer. The droplet produced at all pressures presented a very fine spray, which in agriculture may promote losses by evaporation and drift. For all nozzle tips, except D8 in pressures 1.828, 2.532 e 2.813 kPa, the difference between the observed flow rate indicated by the manufacturer was higher than 5%. The paper demonstrates that the nozzle tip tested, in spite of not having uniform flow rate, may promote the contamination of spray operator and environment due to the droplet spectrum produced.