Avaliação de cenários para a gestão dos resíduos domiciliares na região norte do Vale do Paraíba/SP

Pós-graduação em Engenharia de Produção - FEB

Recycling scrap automotive heat shield insulation material

Automotive heat shields are usually composed of two metal sheets enclosing an insulating material with a paper-like texture that contains refractory ceramic particles. This article discusses the results achieved by recycling the scrap automotive insulation that is discarded in landfills, using the same concept as paper recycling. For comparison with the original product, tests of thickness, bulk density, weight loss on ignition, tensile strength, compressibility, and recovery were performed on recycled materials produced in a so-called "manual" process (involving little automation and performed in adapted facilities) without pressing, and pressed once, twice, and four times. Materials recycled in a so-called "industrial" process (in a paper recycling plant) without pressing, and pressed once were also tested. The recycled materials can be considered approved with respect to the main requirement, thermal insulation, since they dissipated the under-hood temperature by more than 300 A degrees C (like the original product). Like the heat insulation tests, the thermogravimetric analysis suggested that the recycled materials showed higher stability than the original product. Thermogravimetric, microscopy, and energy dispersive spectroscopy analyses indicated that the structural and compositional characteristics of the original product were preserved after recycling.

Study of ceramic block manufacture with the addition of waste from iron ore extraction

This work is intended to study the possibility of adding an amount of waste from iron mining in the ceramic mass. Clay and coal, from Vale do Paraiba, Sao Paulo, Brazil, were used in this research. These raw materials are used in the ceramic block manufacture. Clay and waste were analyzed by X-ray fluorescence and X-ray diffraction, particle size, differential thermal and thermogravimetric analysis. Liquid limit and plasticity index tests were performed in order to determine the amount of waste that which should be used in the ceramic mass. After determining the amount of waste, all samples were uniaxially pressed and sintered at 900 degrees C. Surface roughness measurements, apparent porosity and bulk density technique and three-point flexural tests were also performed to characterize the samples. The results showed that by adding the exact amount of waste, which was determined by the essays, it is possible to manufacture solid bricks.

Implicações da disposição de lodo de estação de tratamento de esgoto em solo no Brasil

The management of solid waste originated from the treatment of domestic and industrial sewage in wastewater treatment plants is a current challenge in the Brazilian reality. However, the planning and the final destination of sludge end up being overlooked, causing serious damage to human health and the environment. The use of sewage sludge in the agriculture is growing in Brazil and is regulated by the Resolução CONAMA Nº 375/2006 which establishes the criteria and parameters so that the sludge can be disposed on the ground safely to the environment and the population. This study aims to define the effects of using sewage sludge in soil according to the results of the bibliographic survey of theoretical and practical studies using this waste in the recovery and conditioning of soil for agriculture and recuperation of degraded areas, and to define whether such type of sludge recycling is environmentally and socially feasible and safe. It can be said that the reuse of sewage sludge in soil meets the search requirements for an alternative that brings agronomic, environmental and economic benefits, as well as being an environmental and social healthy alternative if properly attended the laws that deal with the subject, anyway those should be reviewed and updated taking into account Brazilian soil and climate conditions, thus justifying need for more studies in the area

Life cycle assessment applied to municipal solid waste management: a case study

This study analyzes the environmental performance of the Municipal Solid Waste Management System (MSWMS) of Piedade, São Paulo, from a systemic perspective. A life cycle assessment (LCA) technique was applied according to an attributional approach to evaluate both the current operational situation and different prospective scenarios, which were devised based on the application of targets for recycling dry and wet waste suggested by the pre-draft version of the Brazilian Plan for Solid Waste. The life cycle impact assessment method EcoIndicator 99, in association with normalization and weighting procedures, was used to conduct the analysis. It was observed that the adoption of goals of 30%, 50% and 70% for recovering of the recyclable dry waste, resulted in improvement of the environmental performance of the waste management system under analysis, respectively of 10%, 15% and 20%. It was also possible to detect an evolution in the order of 54% in reducing impacts resulting from the adoption of targets for composting. LCA proved to be effective for the evaluation of the environmental performance of MSWMS-Piedade. However, for future evaluations, the attributional approach should be replaced by the methodological practice of substitution to enable the avoided burdens to be considered in estimations of the environmental performance municipal solid waste management systems.

Potencial de contribuição e importância socioambiental dos 'catadores autônomos' de Rio Claro (SP) para o programa de coleta seletiva municipal

The Urban Solid Residues are the rests of human activity, popularly known by trash and considered by population like useless, undesirable and disposable. On the other hand, for the waste pickers, solid residues are the beginning of a cycle: they see in the other's people trash the only income, an economic value. Currently, in brazilian cities, one million collectors act, alone or in cooperatives, socially excluded by the work they do. The National Policy of Solid Residues (PNRS), instituted in 2010, established guidelines to the execution of integrated residues management, with should be practiced by city halls and other governmental institutions. This policy has, besides other things, goals of residues reduction and inclusion of waste pickers in the mechanism of selective collect and recycling. However, this and other public policies created for residue management are benefic only for cooperated waste pickers. That could negatively affect most of this class, since 90% are waste pickers working in a precarious way on the country's streets. This study has for objective show that most of waste pickers that work in a precarious way on the brazilian territory has a huge potential for the solid residues recycling chain and how they should be valued for the environmental services they provide, so they can be included with dignity on the society, ensuring economic and social benefits for this workers. The methodology adopted was based on the amount of residue collected by the 44 cooperated members of the Rio Claro‟s waste pickers cooperative to estimate the potential of collect and recycling did by 210 autonomous waste pickers who are active on city streets. It was observed that the cooperative collects the equivalent of 10.2% of all recyclable residues generated by city population. However, with the potential that these autonomous waste pickers have, which together could contribute 465 tonnes of solid residues per month, or 5,570 tons a year...

Estudo sobre o uso de agregados reciclados na composição de concretos e argamassas

Two of the major problems caused by construction activity are the production of construction and demolition waste (CDW) and the exploitation of mineral resources, causing big impacts on the environment. Therefore, the recycling has been shown as an alternative to mitigate the harmful effects of waste on the urban environment and prevent the exploitation of new raw materials. This course work aims to study the behavior of recycled aggregates from Vale do Paraíba in concrete and mortar. Initially, it presents the definitions of recycled aggregates according to CONAMA Resolution No. 307/2002, the aggregate settings for concrete and mortar (such as the grain size, its origin and density, and the characterization parameters according to ABNT), and the definition of ACI method of concrete mix design. Afterwards, it presents the characterization of materials separated by assays. After that, it shows the theoretical concrete proportioning applying the ACI method and experimental concrete proportioning. Then, the analysis of results is performed to finally conclude that the materials provided can't be used to replace natural aggregates because they cannot have the same performance. With the studies, it could be observed that the recycled aggregate presents a great complexity and diversity in origin, therefore the form how the material should be handled requires great care

Potencial de contribuição e importância socioambiental dos 'catadores autônomos' de Rio Claro (SP) para o programa de coleta seletiva municipal

The Urban Solid Residues are the rests of human activity, popularly known by trash and considered by population like useless, undesirable and disposable. On the other hand, for the waste pickers, solid residues are the beginning of a cycle: they see in the other's people trash the only income, an economic value. Currently, in brazilian cities, one million collectors act, alone or in cooperatives, socially excluded by the work they do. The National Policy of Solid Residues (PNRS), instituted in 2010, established guidelines to the execution of integrated residues management, with should be practiced by city halls and other governmental institutions. This policy has, besides other things, goals of residues reduction and inclusion of waste pickers in the mechanism of selective collect and recycling. However, this and other public policies created for residue management are benefic only for cooperated waste pickers. That could negatively affect most of this class, since 90% are waste pickers working in a precarious way on the country's streets. This study has for objective show that most of waste pickers that work in a precarious way on the brazilian territory has a huge potential for the solid residues recycling chain and how they should be valued for the environmental services they provide, so they can be included with dignity on the society, ensuring economic and social benefits for this workers. The methodology adopted was based on the amount of residue collected by the 44 cooperated members of the Rio Claro‟s waste pickers cooperative to estimate the potential of collect and recycling did by 210 autonomous waste pickers who are active on city streets. It was observed that the cooperative collects the equivalent of 10.2% of all recyclable residues generated by city population. However, with the potential that these autonomous waste pickers have, which together could contribute 465 tonnes of solid residues per month, or 5,570 tons a year...

Estudo sobre o uso de agregados reciclados na composição de concretos e argamassas

Two of the major problems caused by construction activity are the production of construction and demolition waste (CDW) and the exploitation of mineral resources, causing big impacts on the environment. Therefore, the recycling has been shown as an alternative to mitigate the harmful effects of waste on the urban environment and prevent the exploitation of new raw materials. This course work aims to study the behavior of recycled aggregates from Vale do Paraíba in concrete and mortar. Initially, it presents the definitions of recycled aggregates according to CONAMA Resolution No. 307/2002, the aggregate settings for concrete and mortar (such as the grain size, its origin and density, and the characterization parameters according to ABNT), and the definition of ACI method of concrete mix design. Afterwards, it presents the characterization of materials separated by assays. After that, it shows the theoretical concrete proportioning applying the ACI method and experimental concrete proportioning. Then, the analysis of results is performed to finally conclude that the materials provided can't be used to replace natural aggregates because they cannot have the same performance. With the studies, it could be observed that the recycled aggregate presents a great complexity and diversity in origin, therefore the form how the material should be handled requires great care

Waste management in Forlì-Cesena province: Life Cycle Assessment (LCA) of Forlì incinerator

This work assesses the environmental impact of a municipal solid waste incinerator with energy recovery in Forlì-Cesena province (Emilia-Romagna region, Italy). The methodology used is Life Cycle Assessment (LCA). As the plant already applies the best technologies available in waste treatment, this study focuses on the fate of the residues (bottom and fly ash) produced during combustion. Nine scenarios are made, based on different ash treatment disposing/recycling techniques. The functional unit is the amount of waste incinerated in 2011. Boundaries are set from waste arrival in the plant to the disposal/recovery of the residues produced, with energy recovery. Only the operative period is considered. Software used is GaBi 4 and the LCIA method used is CML2001. The impact categories analyzed are: abiotic depletion, acidification, eutrophication, freshwater aquatic ecotoxicity, global warming, human toxicity, ozone layer depletion, photochemical oxidant formation, terrestrial ecotoxicity and primary energy demand. Most of the data are taken from Herambiente. When primary data are not available, data from Ecoinvent and GaBi databases or literature data are used. The whole incineration process is sustainable, due to the relevant avoided impact given by co-generator. As far as regards bottom ash treatment, the most influential process is the impact savings from iron recovery. Bottom ash recycling in road construction or as building material are both valid alternatives, even if the first option faces legislative limits in Italy. Regarding fly ash inertization, the adding of cement and Ferrox treatment results the most feasible alternatives. However, this inertized fly ash can maintain its hazardous nature. The only method to ensure the stability of an inertized fly ash is to couple two different stabilization treatments. Ash stabilization technologies shall improve with the same rate of the flexibility of the national legislation about incineration residues recycling.

Valorisation of organic waste: new developments from proton nuclear magnetic resonance characterization

The last half-century has seen a continuing population and consumption growth, increasing the competition for land, water and energy. The solution can be found in the new sustainability theories, such as the industrial symbiosis and the zero waste objective. Reducing, reusing and recycling are challenges that the whole world have to consider. This is especially important for organic waste, whose reusing gives interesting results in terms of energy release. Before reusing, organic waste needs a deeper characterization. The non-destructive and non-invasive features of both Nuclear Magnetic Resonance (NMR) relaxometry and imaging (MRI) make them optimal candidates to reach such characterization. In this research, NMR techniques demonstrated to be innovative technologies, but an important work on the hardware and software of the NMR LAGIRN laboratory was initially done, creating new experimental procedures to analyse organic waste samples. The first results came from soil-organic matter interactions. Remediated soils properties were described in function of the organic carbon content, proving the importance of limiting the addition of further organic matter to not inhibit soil processes as nutrients transport. Moreover NMR relaxation times and the signal amplitude of a compost sample, over time, showed that the organic matter degradation of compost is a complex process that involves a number of degradation kinetics, as a function of the mix of waste. Local degradation processes were studied with enhanced quantitative relaxation technique that combines NMR and MRI. The development of this research has finally led to the study of waste before it becomes waste. Since a lot of food is lost when it is still edible, new NMR experiments studied the efficiency of conservation and valorisation processes: apple dehydration, meat preservation and bio-oils production. All these results proved the readiness of NMR for quality controls on a huge kind of organic residues and waste.

Verhalten von Recycling-Materialien in der Umwelt : Labor- und Feldversuche

Im Baugewerbe fallen jährlich mehrere Millionen Tonnen an Baureststoffen an, die nach erfolgter Aufbereitung als Recycling-Baustoffe erneut verwendet werden können. Allerdings besteht Unklarheit hinsichtlich der Stofffreisetzung aus Recycling-Materialien sowie der Parameter, die zur Beurteilung im Wesentlichen heranzuziehen sind. Des Weiteren gilt es der Frage nachzugehen, welche Laborversuche eine realistische Prognose zum Stoffaustrag unter Freilandbedingungen ermöglichen. Ein Ergebnisvergleich aus Feld- und Laborversuchen mit Recycling-Materialien zeigt, dass weder Ammoniumnitrat-Extraktion, pH-stat Versuch noch S4- und Modifizierter S4-Test genauere Prognosen zum Stoffaustrag unter Freilandbedingungen ermöglichen. Mit einem Langzeit-Standtest sowie Schüttelversuchen mit unterschiedlichen Wasser/Feststoff-Verhältnissen lässt sich der Einfluss durch verschiedene Korngrößen sowie Materialabrieb besser kontrollieren. Diese Versuchskombination erlaubt Rückschlüsse auf die Löslichkeit und Verfügbarkeit von Stoffen in den Recycling-Materialien. Die Ergebnisse aus Säulenversuchen weisen auf eine gute Vergleichbarkeit mit den Feldversuchen hin, was sich an denselben vorherrschenden Prozessen bei der Freisetzung für eine Reihe von Stoffen zeigt. Bei mehreren Stoffen treten ähnliche Konzen-trationshöchstwerte bei Säulen- und Feldversuch auf, ebenso zeigt der Vergleich aufsummierter Massenanteile für den Säulenversuch, dass bei einer Reihe von Stoffen eine grobe Abschätzbarkeit für eine Langzeitprognose unter Freilandbedingungen existiert. Als wesentliche Parameter für die Stofffreisetzung aus den Recycling-Materialien sind neben CO2-Einfluss und pH-Wert ebenfalls Temperatureinfluss, Material-Heterogenität sowie einzusetzende Korngröße anzusehen.

Recycling of end of life concrete fines (0 - 4 mm) into silica and cement

The purpose of this work is to find a methodology in order to make possible the recycling of fines (0 - 4 mm) in the Construction and Demolition Waste (CDW) process. At the moment this fraction is a not desired by-product: it has high contaminant content, it has to be separated from the coarse fraction, because of its high water absorption which can affect the properties of the concrete. In fact, in some countries the use of fines recycled aggregates is highly restricted or even banned. This work is placed inside the European project C2CA (from Concrete to Cement and Clean Aggregates) and it has been held in the Faculty of Civil Engineering and Geosciences of the Technical University of Delft, in particular, in the laboratory of Resources And Recycling. This research proposes some procedures in order to close the loop of the entire recycling process. After the classification done by ADR (Advanced Dry Recovery) the two fractions "airknife" and "rotor" (that together constitute the fraction 0 - 4 mm) are inserted in a new machine that works at high temperatures. The temperatures analysed in this research are 600 °C and 750 °C, cause at that temperature it is supposed that the cement bounds become very weak. The final goal is "to clean" the coarse fraction (0,250 - 4 mm) from the cement still attached to the sand and try to concentrate the cement paste in the fraction 0 - 0,250 mm. This new set-up is able to dry the material in very few seconds, divide it into two fractions (the coarse one and the fine one) thanks to the air and increase the amount of fines (0 - 0,250 mm) promoting the attrition between the particles through a vibration device. The coarse fraction is then processed in a ball mill in order to improve the result and reach the final goal. Thanks to the high temperature it is possible to markedly reduce the milling time. The sand 0 - 2 mm, after being heated and milled is used to replace 100% of norm sand in mortar production. The results are very promising: the mortar made with recycled sand reaches an early strength, in fact the increment with respect to the mortar made with norm sand is 20% after three days and 7% after seven days. With this research it has been demonstrated that once the temperature is increased it is possible to obtain a clean coarse fraction (0,250 - 4 mm), free from cement paste that is concentrated in the fine fraction 0 - 0,250 mm. The milling time and the drying time can be largely reduced. The recycled sand shows better performance in terms of mechanical properties with respect to the natural one.

Examining the Justification for Residential Recycling

Municipalities in the United States have for the past two decades initiated two policies to reduce residential solid waste generation by increasing recycling. The first policy, implemented in over 4,000 municipalities in the United States, requires households to pay a fee for each unit of garbage presented at the curb for collection. The second policy, initiated in 8,875 municipalities, subsidizes household recycling efforts by providing free curbside collection of certain recyclable materials. Both initiatives serve as examples of incentive-based environmental policies favored by many economists. But before economists can celebrate this wide-spread adoption of incentive-based environmental policies, further examination reveals that potentially inefficient command and control policies have been more instrumental in promoting recycling than might be commonly known. This article examines the empirical lessons gained from studying twenty years of solid waste policy in the United States and argues for the replacement of several state recycling mandates with a system of state and/or national landfill taxes.

Explaining the Growth in Municipal Recycling Programs: The Role of Market and Non-Market Factors

The implementation of thousands of municipal recycling programs in the United States has increased recycling’s portion of solid waste from 10% to 30% over the past decade. But the lack of accurate data has spurred a debate over whether the growth in recycling can be attributed to market or nonmarket factors. To address this issue, this article conducts a benefit-cost analysis of a municipal recycling program. Results suggest recycling is costly. So why, then, does it remain popular? This article suggests that local governments could be responding to households that perceive a benefit from recycling services. These benefits are estimated with a contingent valuation survey.