Morfologia e propriedades mecânicas da fibra de sisal unidirecional e em sobreposição de compósito com resina epóxi

The composites manufactured with long fibres aligned in a single direction, and overlay has been shown to have better performance than the short fibers randomly distributed. In particular, the lignocellulosic fibers extracted from the sisal leaves, used in conjunction with the epoxy resin has attracted the attention of many researchers because the final properties of the system formed. In this work composites based on epoxy resin reinforced with sisal fibers were manufactured. The sisal fibres were treated with an alkaline solution of 0.06 mol/l NaOH. The treated, and untreated fibres were subjected to tension x extension tests. The composites were manufactured in the "Lossy" mold with the specifications of the samples to be produced (300x20x4 mm). The tension tests were carried out in accordance with the ASTM standards 3039 (for the composite aligned in a single direction) and ASTM D5573 (for composites in overlay), three point bending tests were performed according to ASTM D790. Analyzing the results of the tests of tension and three point bending tests, it was observed that the composites with the configuration of overlapping had the better elastic module in both tests. As to the maximum resistance to tension, the best result was the composites aligned in a single direction. Tests of absorption of water and micrographs are in progress

Estudo das propriedades físico-químicas do biodiesel e suas influências na deterioração dos elastômeros aplicados no sistema de injeção dos motores diesel

The biodiesel use has become important due to its renewable character and to reduce environmental impacts during the fuel burning. Theses benefit will be valid if the fuel shows good performance, chemistry stability and compatibility with engines. Biodiesel is a good fuel to diesel engines due to its lubricity. Then, the aimed of this study was to verify the physicalchemistry properties of biodiesel and their correlations with possible elastomers damage after biodiesel be used as fuel in an injection system. The methodology was divided in three steps: biodiesels synthesis by transesterification of three vegetable oil (soybean, palm and sunflower) and their physical-chemistry characterization (viscosity, oxidative stability, flash point, acidity, humidity and density); pressurized test of compatibility between elastomers (NBR and VITON) and biodiesel, and the last one, analyze of biodiesels lubricity by tribological test ball-plan( HFRR). Also, the effect of mixture of biodiesel and diesel in different concentrations was evaluated. The results showed that VITON showed better compatibility with all biodiesel blends in relation to NBR, however when VITON had contact with sunflower biodiesel and its blends the swelling degree suffer higher influences due to biodiesel humidity. For others biodiesels and theirs blends, this elastomer kept its mechanical properties constant. The better tribological performance was observed for blends with high biodiesel concentration, lower friction coefficient was obtained when palm biodiesel was used. The main mechanisms observed during the HFRR tests were abrasive and oxidative wear

Competitividade de diferentes atmosferas de plasma sobre as propriedades hidrofílicas em tecidos de polilático

Os polímeros biodegradáveis, como o poliácido láctico (PLA) apesar de consolidado nos campos farmacêuticos, médico e biomédico como biomateriais úteis para aplicações variadas, porém, depende da necessidade de funcionalizar a sua superfície estudando suas propriedades tais como hidrofilidade e hidrofobicidade favorecendo a interação do polímero com os materiais de aplicação farmacêutica, médica e biomédica. Este trabalho tem como objetivo produzir um material com características diferentes em cada um de seus lados, sendo um lado hidrofílico e o outro hidrofóbico. O substrato têxtil utilizado neste estudo foi um tecido de malha de composição 100% PLA que é biodegradável e biocompatível, o que possibilita sua aplicação na área biomédica. Para modificação superficial foi utilizado o tratamento a plasma de baixa pressão. A técnica de modificação de superfície por plasma foi escolhida por ser uma tecnologia limpa, anticorrosiva e não tóxica ao contrario de muitos processos químicos convencionais utilizados na indústria têxtil, além disso, não afeta as propriedades de massa do substrato. Neste estudo, um lado da superfície do substrato foi tratado com plasma oxigênio, argônio e nitrogênio, para o trabalho de melhoria da hidrofilidade da superfície e metano para a hidrofobicidade da amostra. A espectroscopia de emissão ótica (OEE) foi utilizada para fazer o diagnóstico das espécies do plasma durante o tratamento. Após o tratamento a plasma as amostras foram caracterizadas por medidas de ângulo de contato, microscopia eletrônica de varredura (MEV), Espectroscopia de fotoelétrons de raios-X (XPS), Infravermelho com Transformada de Fourier (FTIR) de reflexão total atenuada (ATR), medidas da área de espalhamento do líquido e arraste vertical. Onde foi caracterizado o aumento e diminuição da molhabilidade das amostras tratadas por plasma bem como as variáveis que contribuíram para tal efeito. O tratamento das amostras de PLA com O2 + CH4 apresenta comportamento hidrofílico no lado tratado com O2, apresentando aumento de rugosidade e grupos funcionais e no lado tratado com CH4, apresentando a formação de um filme polimérico formado sobre a superfície da amostra. O tratamento com N2 + CH4 apresenta comportamento hidrofóbico, porém com variações no fluxo do CH4 tem-se um controle da molhabilidade na superfície das amostras, podendo ir de hidrofóbico a hidrofílico, neste tratamento as amostras apresentaram pequenas diferenças de molhabilidade entre os lados tratados com plasma de N2 e com plasma de CH4

Propriedades cerâmicas e imobilização do manganês em cerâmica estrutural

In this work is the addition of a metallic ion, of the metal Manganese, in a clay of Rio Grande do Norte state for structural ceramics use, the objective this study was to assess the evolution of ceramic properties. The clay was characterized by Chemical and Thermal analysis and Xray difraction. The metallic ion was added in the clay as aqueous solutions at concentrations of 100, 150 and 200 mg / L. The molded by extrusion and the burned were temperatures at 850, 950, 1050 and 1150 º C. Was made Chemical Analysis and investigated the following parameters environmental and ceramic: Solubility, Colour, Linear Retraction (%), Water Absorption (%), Gresification Curves, Apparent Porosity (%), Apparent Specific Mass (g/cm3) and Flexion Rupture Module (kgf/cm2). The results showed that increasing the concentration of metallic ion, properties such as Apparent Porosity (%), Water Absorption (%) decreases and the Flexion Rupture Module (kgf/cm2) increases with increasing temperature independent of the concentration of the ion. The gresification curves showed that the optimum firing temperatures were in the range between 950 and 1050 ° C. The evaluation of the properties showed that the ceramic material can be studied its use in solid brick and ceramic materials with structural function of filling. The results of solubility showed that the addition of ion offers no risk to the environment

Estudo das propriedades físico-químicas de biocombustíveis microemulsionados

The development of new fuels is an important field of scientific and technological activities, since much of the energy consumed in the world is obtained from oil, coal and natural gas, and these sources are limited and not renewable. Recently it has assessed the employment of microemulsions as an alternative for obtaining fuel isotropic between phases originally not miscible. Among many advantages, emphasizes the application of substances that provide the reduction of levels of emissions compared to fossil fuels. Thus, this work was a study of various microemulsified systems, aiming to check the performance of the winsor regions front of the use of surfactants: RENEX 18 → 150, UNITOL L-60 → L-100 and AMIDA 60, together with structure of esters from soybean and castor bean oils. From the results it were chosen four systems to physico-chemical analyzes: System I RENEX 60, Soil bean oil, methylic ester (EMOS) and water; System II RENEX 60/AMIDA 60, EMOS and water; System III RENEX 70, mamona oil methylic ester (EMOM) and water and System IV RENEX 95, EMOM and water. The tests of physico-chemical characterization and study of temperature increase were done with nine points with different compositions in a way to include the interest area (microemulsion W/O). After this study, was conducted a modeling to predict the viscosity, the property is more varied as function of compositions systems changes. The best results were the systems II and IV with a temperature stability above 60°C. The system I had its physico-chemical characterization very similar to a fossil fuel. The system II was the best one due to its corrosivity be stable. In the modeling the four systems had shown good, with an error that varied between 5 and 18%, showing to be possible the viscosity prediction from the composition of the system. The effects the microemulsion and the engine´s performance with the microemulsion were also avaliated. The tests were performed in a cycle-diesel engine. The potency and consumption were analysed. Results show a slight increase the rendiment fuel compared with the conventional as well as a decrease in specific consumption

TERMOFOSFATOS: ALTERAÇÕES em PROPRIEDADES QUÍMICAS em UM LATOSSOLO VERMELHO-ESCURO E EFICIÊNCIA AGRONÔMICA

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Obtenção de Propriedades Físico-Químicas de Misturas de Hidrocarbonetos em Baixa e Alta Pressão Visando a Caracterização e a Modelagem

The composition of petroleum may change from well to well and its resulting characteristics influence significantly the refine products. Therefore, it is important to characterize the oil in order to know its properties and send it adequately for processing. Since petroleum is a multicomponent mixture, the use of synthetic mixtures that are representative of oil fractions provides a better understand of the real mixture behavior. One way for characterization is usually obtained through correlation of physico-chemical properties of easy measurement, such as density, specific gravity, viscosity, and refractive index. In this work new measurements were obtained for density, specific gravity, viscosity, and refractive index of the following binary mixtures: n-heptane + hexadecane, cyclohexane + hexadecane, and benzene + hexadecane. These measurements were accomplished at low pressure and temperatures in the range 288.15 K to 310.95 K. These data were applied in the development of a new method of oil characterization. Furthermore, a series of measurements of density at high pressure and temperature of the binary mixture cyclohexane + n-hexadecane were performed. The ranges of pressure and temperature were 6.895 to 62.053 MPa and 318.15 to 413.15 K, respectively. Based on these experimental data of compressed liquid mixtures, a thermodynamic modeling was proposed using the Peng-Robinson equation of state (EOS). The EOS was modified with scaling of volume and a relatively reduced number of parameters were employed. The results were satisfactory demonstrating accuracy not only for density data, but also for isobaric thermal expansion and isothermal compressibility coefficients. This thesis aims to contribute in a scientific manner to the technological problem of refining heavy fractions of oil. This problem was treated in two steps, i.e., characterization and search of the processes that can produce streams with economical interest, such as solvent extraction at high pressure and temperature. In order to determine phase equilibrium data in these conditions, conceptual projects of two new experimental apparatus were developed. These devices consist of cells of variable volume together with a analytical static device. Therefore, this thesis contributed with the subject of characterization of hydrocarbons mixtures and with development of equilibrium cells operating at high pressure and temperature. These contributions are focused on the technological problem of refining heavy oil fractions

Propriedades dos sistemas de numeração: uma sequência didática em uma abordagem histórica

This paper aims to describe the construction and validation of a notebook of activities whose content is a didactic sequence that makes use of the study of ancient numbering systems as compared to the object of our decimal positional numbering system Arabic. This is on the assumption that the comparison with a system different from our own might provide a better understanding of our own numbering system, but also help in the process of arithmetic operations of addition, subtraction and multiplication, since it will force us to think in ways that are not routinely object of our attention. The systems covered in the study were the Egyptian hieroglyphic system of numbering, the numbering system Greek alphabet and Roman numbering system, always compared to our numbering system. The following teachung is presented structured in the form of our activities, so-called exercise set and common tasks around a former same numbering system. In its final stage of preparation, the sequence with the participation of 26 primary school teachers of basic education

Avaliação do potencial das imagens quickbird ortorretificadas para o mapeamento das propriedades localizadas na área de expansão e vazios urbanos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da influência de tratamentos químicos da fibra de sisal nas propriedades de compósitos com borracha nitrílica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito da adição de lodo de estação de tratamento de água (ETA) nas propriedades de material cerâmico estrutural

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Propriedades mecânicas do músculo de ratos adultos e idosos, exercitado pós-imobilização

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação de algumas propriedades funcionais das farinhas de tremoço doce (Lupinus albus) e feijão guandu (Cajanus cajan (L) Millsp) e sua utilização na produção de fiambre

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Propriedades magnéticas de nanopartículas de ferro em substratos antiferromagnéticos

The effect of finite size on the magnetic properties of ferromagnetic particles systems is a recurrent subject. One of the aspects wide investigated is the superparamagnetic limit where the temperature destroys the magnetic order of ferromagnetic small particles. Above the block temperature the thermal value of the magnetic moment of the particle vanishes, due to thermal fluctuations. The value of the blocking temperature diminishes when the size of the particle is reduced, reflecting the reduction of the anisotropy energy barrier between the uniform states along the uniaxial axis. The increasing demand for high density magnetic media has recently attracted great research interest in periodic arrangements of nanometric ferromagnetics particles, approach in the superparamagnetic limit. An interesting conjecture is the possibility of stabilization of the magnetic order of small ferromagnetic particles (F) by interface coupling with antiferromagnetic (AF) substrate. These F/AF systems may also help to elucidate some details of the effect of exchange bias, because the effect of interface roughness and the paper of domain walls, either in the substrate or the particle, are significantly reduced. We investigate the magnetic phases of small ferromagnetic particles on a antiferromagnetic substrate. We use a self-consistent local field method, incorporating the interface field and the dipole interaction between the spins of the ferromagnetic particle. Our results indicate that increasing the area of the interface favors the formation of the uniform state. Howere above a critical height value appears a state non-uniform is formed where the spins of in the particle s free surface are rotated with respect to the interface spins direction. We discuss the impact of the competition between the dipolar and interface field on the magnetic charge, that controls the field of flux leakage of the particle, and on the format of the hysteresis curves. Our results indicate that the liquid magnetic charge is not a monotonically increasing function of the height of the particle. The exchange bias may display anomalous features, induced for the dipolar field of the spins near the F/AF interface

Propriedades Físicas do Semicondutor Bi2Te3

Thermoelectric Refrigerators (TEC Thermoelectric Cooling) are solid-state heat pumps used in applications where stabilization of temperature cycles or cooling below the room temperature are required. TEC are based on thermoelectric devices, and these in turn, are based on the Peltier effect, which is the production of a difference in temperature when an electric current is applied to a junction formed by two non-similar materials. This is one of the three thermoelectric effects and is a typical semiconductor junction phenomenon. The thermoelectric efficiency, known as Z thermoelectric or merit figure is a parameter that measures the quality of a thermoelectric device. It depends directly on electrical conductivity and inversely on the thermal conductivity. Therefore, good thermoelectric devices have typically high values of electrical conductivity and low values of thermal conductivity. One of the most common materials in the composition of thermoelectric devices is the semiconductor bismuth telluride (Bi2Te3) and its alloys. Peltier plates made up by crystals of semiconductor P-type and N-type are commercially available for various applications in thermoelectric systems. In this work, we characterize the electrical properties of bismuth telluride through conductivity/resistivity of the material, and X-rays power diffraction and magnetoresistance measurements. The results were compared with values taken from specific literature. Moreover, two techniques of material preparation, and applications in refrigerators, are discussed