Antibacterial titania-based photocatalytic extruded plastic films

Photocatalytic antibacterial low density polyethylene (LDPE)–TiO2 films are produced by an extrusion method and tested for photocatalytic oxidation activity, via the degradation of methylene blue (MB) and photocatalytic antibacterial activity, via the destruction of Escherichia coli. The MB test showed that extruded LDPE films with a TiO2 loading 30 wt.% were of optimum activity with no obvious decrease in film strength, although the activity was less than that exhibited by the commercial self-cleaning glass, Activ®. UVC pre-treatment (9.4 mW cm−2) of the latter film improved its activity, with the level of surface sites available for MB adsorption increasing linearly with UVC dose. Although the MB test revealed an optimum exposure time of ca. 60 min photocatalytic oxidation activity, only 30 min was used in the photocatalytic antibacterial tests in order to combine minimal reduction in film integrity with maximum film photocatalytic activity. The photocatalytic antibacterial activity of the latter film was over 10 times that of a non-UVC treated 30 wt.% TiO2 film, which, in turn was over 100 times more active than Activ®.

The nitric oxide ISO photocatalytic reactor system: Measurement of NOx removal activity and capacity

Although the NO removal-based air-purification ISO method ISO 22197-1:2007 is well established, its preconditioning requirements mean that only the initial activity of the photocatalyst under test is measured owing to the often-reported, gradual alteration of the surface kinetics for NO oxidation by air through the accumulation of surface HNO3. Herein, we compare the photocatalytic NO removal abilities of a number of different, common TiO2 materials, surface-saturated with photogenerated HNO3, with their behaviours observed during the typical 5 h-long ISO standard test. It is found that all the TiO2 materials studied eventually become largely NO to NO2 converters after sufficient exposure to NO under irradiation (>5 h) due to the accumulation of surface HNO3. The UV exposure time, t*, necessary to reach this HNO3 saturated condition is different for each different catalyst. As a consequence, an alternative preconditioning process for the ISO method is proposed which can be used to provide a more realistic measure of the photocatalytic activity of the underlying material and provide a measure of the NOx removing capacity of the photocatalytic material under test.

Powder semiconductor photocatalysis in aqueous solution: An overview of kinetics-based reaction mechanisms

A brief, historical overview of 10 apparently different, although in some cases, upon inspection, closely related, popular proposed reaction mechanisms and their associated rate equations, is given and in which the rate expression for each mechanism is derived from basic principles, Appendix A. In Appendix B, each of the 5 main mechanisms are tested using datasets, comprising initial reaction rate vs. organic pollutant concentration, [P] and incident irradiance, ρ, data, reported previously for TiO2, where P is phenol, 4-chlorophenol and formic acid. The best of those tested, in terms of overall fit, simplicity, usefulness and versatility is the disrupted adsorption kinetic model proposed by Ollis. The usual basic assumptions made in constructing these mechanisms are reported and the main underlying concerns explored.

Targeting of photooxidative damage on single-stranded DNA representing the bcr-abl chimeric gene using oligonucleotide-conjugates containing [Ru(phen)3](2+)-like photosensitiser groups

Photooxidative damage was induced predominantly at a single guanine base in a target DNA by irradiation (lambda > 330 nm) in the presence of complementary oligodeoxynucleotide conjugates (ODN-5'-linker-[Ru(phen)3]2+) (phen = 1,10-phenanthroline). The target DNA represents the b2a2 variant of the chimeric bcr-abl gene implicated in the pathogenesis of chronic myeloid leukaemia, and the sequence of the 17mer ODN component of the conjugate (3' G G T A G T T A T T C C T T C T T 5') was complementary to the junction region of the sense strand sequence of this oncogene. Two different conjugates were prepared, both of them by reaction of the appropriate succinimide ester with 5'-hexylamino-derivatised 17mer ODN. In Ru-ODN-1 (7) the linker was -(CH2)6-NHCO-bpyMe (-bpyMe = 4'-[4-methyl-2,2'-bipyridyl]), whereas in Ru-ODN-2 (13) it was -(CH2)6-NHCO-(CH2)3-CONH-phen. Photoexcitation of either of the conjugates when hybridised with the 32P-5'-end-labelled target 34mer 5'T G A C C A T C A A T A A G G A A G A A G21 C C C T T C A G C G G C C 3' (ODN binding site underlined) led to an alkali-labile site predominantly (> 90%) at the G21 base, which is at the junction of double-stranded and single-stranded regions of the hybrid. Greater yields were found with Ru-ODN-1 (7) than with Ru ODN-2 (13). In contrast to this specific cleavage with Ru-ODN-1 (7) or Ru-ODN-2 (13), alkali-labile sites were generated at all guanines when the 34mer was photolysed in the presence of the free sensitiser [Ru(phen)3]2+. Since [Ru(phen)3]2+ was shown to react with 2'-deoxyguanosine to form the diastereomers of a spiroiminodihydantoin derivative (the product from 1O2 reaction), 1O2 might also be an oxidizing species in the case of Ru-ODN-1 (7) and Ru-ODN-2 (13). Therefore to determine the range of reaction, a series of 'variant' targets was prepared, in which G21 was replaced with a cytosine and a guanine substituted for a base further towards the 3'-end (e.g. Variant 3; 5'T G A C C A T C A A T A A G G A A G A A C C G23 C T T C A G C G G32 C C3'). While it was noted that efficient reaction took place at distances apparently remote from the photosensitiser (e.g at G32, but not G23 for Variant 3), this effect could be attributed to hairpinning of the single-stranded region of the target. These results are therefore consistent with the photooxidative damage being induced by a reaction close to the photosensitiser rather than by a diffusible species such as 1O2.

Controlled periodic illumination in semiconductor photocatalysis

Controlled periodic illumination is a hypothesis postulated in the early 1990s for enhancing the efficiency of semiconductor photocatalytic reactions. This technique has been proposed to improve photocatalytic efficiency by the nature of photon introduction alone. Before its application in semiconductor photocatalysis, controlled periodic illumination had been investigated in other fields including photosynthesis. This paper presents a detailed review of the state of the art research undertaken on the application of controlled periodic illumination in semiconductor photocatalysis. The review briefly introduces semiconductor photocatalysis, and then presents a detailed explanation of this technique, its importance to photocatalytic efficiency, an overview of previous results of its application in significant studies and present knowledge. Results from previous as well as some of the most recent studies indicate potential applications of controlled periodic illumination in areas other than just the improvement of the efficiency of the photocatalytic process.

Kinetics of the photocatalysed oxidation of NO in the ISO 22197 reactor

The photocatalytic reactor described in the NOx removal ISO 22197-1:2007 is used to study the kinetics of the process, using a film of P25 TiO2 which has either been conventionally pre-irradiated in a stream of air, or unconventionally in a stream of NO (1 ppmv). In the former case it is shown that the system does not achieve steady state exit levels of NO, probably due to the gradual accumulation of HNO3 on the surface of the photocatalyst. The NO-preconditioned TiO2 film demonstrated excellent steady-state levels when monitored as a function of NO concentration, [NO] and UV irradiance, ρ. However, in this case the photocatalytic reaction under study is NOT NOx removal, but the conversion of NO to NO2. It is shown that the kinetics of this steady state process fit very well to a kinetic expression based on a disrupted adsorption reaction mechanism, which has also been used by others to fit their observed (non-steady state) kinetics for NOx removal on conventionally-(air) preconditioned films of P25. The appropriateness of this model for either system is questioned, since in both systems the kinetics appear to have a significant mass transport element. These findings suggest that mass transport and non-steady-state kinetics are likely to be significant features for most active photocatalytic samples, where the %NO conversion is >7%, and so limits the usefulness of the NOx removal ISO 22197-1:2007.

Síntese de derivados oligoméricos de porfirinas e ftalocianinas

A presente dissertação contempla estudos de funcionalização de 5,10,15,20- tetrafenilporfirina via grupos nitro e amino e a preparação de sistemas porfirina-ftalocianina. Este trabalho encontra-se dividido em quatro partes. Na primeira parte descrevem-se as características gerais de porfirinas e ftalocianinas bem como algumas metodologias de síntese utilizadas na sua preparação e suas potenciais aplicações. Na segunda parte desta dissertação descreve-se a funcionalização de 5,10,15,20-tetrafenilporfirina com arilaminas recorrendo a duas rotas sintéticas diferentes. A reacção de 2-nitro-5,10,15,20-tetrafenilporfirina com anilina ou aminas aromáticas substituídas com grupos dadores de electrões permitiu, através do ataque do nucleófilo ao carbono beta-pirrólico onde está ligado o grupo nitro, ataque ipso, a obtenção de derivados do tipo 2-arilaminoporfirinas e derivados porfirínicos de anéis fundidos, sendo estes últimos resultantes da ciclização oxidativa de 2-arilaminoporfirinas. A reacção entre (2-amino- 5,10,15,20-tetrafenilporfirinato)níquel(II) e brometos de arilo na presença de paládio, reacção de aminação de Buchwald-Hartwig, permitiu, após descomplexação, a preparação de novos derivados do tipo 2- arilaminoporfirinas com grupos substituintes dadores e aceitadores de electrões. Um dos derivados porfirínicos de anéis fundidos foi submetido a reacção de complexação com diferentes iões metálicos e foram estudadas as respectivas propriedades fotoquímicas e electroquímicas. Esses estudos revelaram que estes compostos são bons geradores de oxigénio singuleto e que sofrem processos de oxidação-redução electroquimicamente reversíveis. Esta metodologia foi estendida ainda a brometos de hetarilo (derivados de piridina e tiofeno). Recorrendo ao acoplamento, em condições de Buchwald-Hartwig, de complexos metálicos da 5,10,15,20-tetrafenilporfirina, funcionalizados com grupos amino e bromo, preparam-se dímeros porfirina-amino-porfirina, cujos espectros electrónicos revelam a existência de uma boa “comunicação electrónica” entre as duas subunidades. A terceira parte descreve a síntese de sistemas porfirina-ftalocianina. Recorrendo à condensação estatística entre a 5,10,15,20-tetrafenilporfirina substituída com um grupo ftalonitrilo na posição beta-pirrólica com ftalonitrilo ou ftalonitrilo substituído foram obtidas díades porfirina-ftalocianina onde as duas subunidades se encontram directamente ligadas ou fundidas. Os porfirinilftalonitrilos necessários para a síntese das diferentes díades foram preparados através da reacção de adição do fumaronitrilo à 5,10,15,20- tetrafenilporfirina funcionalizada com o grupo 1,3-butadienilo ou vinilo, seguida de oxidação do aducto resultante. O acoplamento catalisado por paládio entre (2-bromo-5,10,15,20- tetrafenilporfirinato)zinco(II) e [9(10),16(17),23(24)-tri-terc-butil-2- etinilftalocianinato]zinco(II) permitiu a síntese de uma díade porfirinaftalocianina com as duas unidades ligadas por um grupo etinilo. Uma pentíade porfirina-ftalocianina foi obtida através da ciclotetramerização de um dos porfirinilftalonitrilos. A comparação dos espectros electrónicos das diferentes classes de sistemas revela que as correspondentes propriedades electrónicas são altamente afectadas pela distância entre as subunidades e também pelo número de cromóforos presentes no sistema. Os estudos fotofísicos de alguns dos novos compostos acima referidos permitiram verificar a ocorrência eficiente de transferência de energia da subunidade porfirínica para a da ftalocianina, capacidade essa que permitirá a estes sistemas serem usados para modelar o processo fotossintético. Na última parte descrevem-se, pormenorizadamente, todas as experiências efectuadas e as caracterizações espectroscópicas, nomeadamente de espectroscopia de ressonância magnética nuclear (RMN), espectrometria de massa e espectrofotometria de UV-vis, dos compostos sintetizados. Nalguns casos recorreu-se ainda a técnicas de RMN bidimensionais como COSY, HSQC, HMBC, NOESY e ROESY.

Investigation of structural effects on the reactivity of heterocyclic bioactive compounds

Tese de dout., Química, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2008

Photochemical control of rheology

The main objective of the research work developed in the framework of this PhD thesis was the preparation and development of novel photorheological fluids. This was pursued following two distinct strategies. The first one focused on the synthesis of tripodal compounds functionalized with photodimerizable moieties of cinnamic acid, coumarin and anthracene. Two sets of compounds were prepared, varying the central unit as well as spacers resulting in molecules with different solubilities and molecular weight. All compounds were characterized towards their photochemical properties and all exhibited photoreactivity upon irradiation with ultra-violet light. In particular, both coumarin derivatives exhibited the greatest photopolymerization reactivity, resulting in the formation of dendrimeric nanoparticles or in the increase of viscosity of organic solutions. The second strategy was focused on the careful design of photosensitive ionic liquids, based on the results of several quantitative structure-property relationship studies. Thus, photosensitive ionic liquids were synthesized bearing cinnamic acid or coumarin moieties in the organic cation. Upon irradiation, all compounds exhibited reactivity, which resulted in changes in their physical properties, such as melting point or viscosity. In addition, novel coumarin chromophores with different photophysical and photochemical properties were developed. It is expected that these compounds may find application in the preparation of new photosensitive ionic liquids.

Effect of pH on non-photochemical quenching in spinach photsystem 2 particles as measured by picosecond fluorescence decay kinetics

Single photon timing was used to study picosecond chlorophyll a fluorescence decay kinetics of pH induced non-photochemical quenching in spinach photosystem 2 particles. The characteristics of this quenching are a decrease in chlorophyll a fluorescence yield as well as a decrease in photochemistry at low pH. Picosecond kinetics of room temperature fluorescence temporally resolve the individual components of the steady state fluorescence yield into components that are related to primary energy conversion processes in photosystem 2. Four components were resolved for dark adapted (Fo), light saturated (Fm), and chemically reduced (Nadithionite) photosystem 2 reaction centres. The fastest and slowest components, indicative of energy transfer to and energy capture by the photosystem 2 reaction centre and uncoupled ("dead") chlorophyll, respectively, were not affected by changing pH from 6.5 to 4.0. The two intermediate components, indicative of electron transfer processes within the reaction centre of photosystem 2, were affected by the pH change. Results indicate that the decrease in the steady state fluorescence yield at low pH was primarily due to the decrease in lifetime and amplitude of the slower of the intermediate components. These results imply that the decrease in steady state fluorescence yield at low pH is not due to changes in energy transfer to and energy capture by the photosystem 2 reaction centre, but is related to changes in charge stabilization and charge recombination in the photosystem 2 reaction centre.

Competing demands for a complex system : photosystem II repair, photoprotection and quantum yield

Photosynthesis in general is a key biological process on Earth and Photo system II (PSII) is an important component of this process. PSII is the only enzyme capable of oxidizing water and is largely responsible for the primordial build-up and present maintenance of the oxygen in the atmosphere. This thesis endeavoured to understand the link between structure and function in PSII with special focus on primary photochemistry, repair/photodamage and spectral characteristics. The deletion of the PsbU subunit ofPSII in cyanobacteria caused a decoupling of the Phycobilisomes (PBS) from PSII, likely as a result of increased rates of PSII photodamage with the PBS decoupling acting as a measure to protect PSII from further damage. Isolated fractions of spinach thylakoid membranes were utilized to characterize the heterogeneity present in the various compartments of the thylakoid membrane. It was found that the pooled PSIILHCII pigment populations were connected in the grana stack and there was also a progressive decrease in the reaction rates of primary photochemistry and antennae size of PSII as the sample origin moved from grana to stroma. The results were consistent with PSII complexes becoming damaged in the grana and being sent to the stroma for repair. The dramatic quenching of variable fluorescence and overall fluorescent yield of PSII in desiccated lichens was also studied in order to investigate the mechanism by which the quenching operated. It was determined that the source of the quenching was a novel long wavelength emitting external quencher. Point mutations to amino acids acting as ligands to chromophores of interest in PSII were utilized in cyanobacteria to determine the role of specific chromophores in energy transfer and primary photochemistry. These results indicated that the Hl14 ligated chlorophyll acts as the 'trap' chlorophyll in CP47 at low temperature and that the Q130E mutation imparts considerable changes to PSII electron transfer kinetics, essentially protecting the complex via increased non-radiative charge Photosynthesis in general is a key biological process on Earth and Photo system II (PSII) is an important component of this process. PSII is the only enzyme capable of oxidizing water and is largely responsible for the primordial build-up and present maintenance of the oxygen in the atmosphere. This thesis endeavoured to understand the link between structure and function in PSII with special focus on primary photochemistry, repair/photodamage and spectral characteristics. The deletion of the PsbU subunit ofPSII in cyanobacteria caused a decoupling of the Phycobilisomes (PBS) from PSII, likely as a result of increased rates of PSII photodamage with the PBS decoupling acting as a measure to protect PSII from further damage. Isolated fractions of spinach thylakoid membranes were utilized to characterize the heterogeneity present in the various compartments of the thylakoid membrane. It was found that the pooled PSIILHCII pigment populations were connected in the grana stack and there was also a progressive decrease in the reaction rates of primary photochemistry and antennae size of PSII as the sample origin moved from grana to stroma. The results were consistent with PSII complexes becoming damaged in the grana and being sent to the stroma for repair. The dramatic quenching of variable fluorescence and overall fluorescent yield of PSII in desiccated lichens was also studied in order to investigate the mechanism by which the quenching operated. It was determined that the source of the quenching was a novel long wavelength emitting external quencher. Point mutations to amino acids acting as ligands to chromophores of interest in PSII were utilized in cyanobacteria to determine the role of specific chromophores in energy transfer and primary photochemistry. These results indicated that the Hl14 ligated chlorophyll acts as the 'trap' chlorophyll in CP47 at low temperature and that the Q130E mutation imparts considerable changes to PSII electron transfer kinetics, essentially protecting the complex via increased non-radiative charge.

Contamination des solutions d’hyper-alimentation intraveineuses (HAIV) néonatales, effet de l’ascorbylperoxyde au foie

Introduction : Chez les nouveau-nés prématurés, l’hyper-alimentation intraveineuse (HAIV) contribue à leur survie, mais elle est aussi une source importante de molécules oxydantes. L’absence d’une protection adéquate contre la lumière ambiante génère in vitro, via la photo-excitation de la riboflavine, du H2O2, des peroxydes organiques et un dérivé peroxydé de la vitamine C, l’ascorbylperoxyde (AscOOH). Plusieurs données du laboratoire associent l’infusion d’HAIV à des désordres lipidiques dans notre modèle animal. L’hypothèse est donc que l’AscOOH a un pouvoir oxydant et est responsable de certains des effets biologiques observés. Mes objectifs sont les suivants : 1) développer une méthode de dosage de l’AscOOH; 2) démontrer, à l’aide du modèle animal bien établi au laboratoire, des relations entre la concentration tissulaire de cette molécule et des paramètres métaboliques et l’état redox au foie et dans la circulation; et 3) confirmer l’effet physiologique de l’AscOOH dans un modèle cellulaire. Méthode : Différents étalons internes potentiels ont été testés pour le dosage de l’AscOOH par spectrométrie de masse après séparation sur HPLC (LC-MS). Les phases mobiles et conditions chromatographiques ont été optimisées. Pour l’objectif 2, des cobayes de 3 jours de vie (n=11) ont reçu par voie intraveineuse une dose d’AscOOH (entre 0 et 3,3mM). Les animaux ont été sacrifiés au 4e jour de traitement pour le prélèvement de tissus. Les concentrations tissulaires d’AscOOH ont été déterminées au LC-MS. La triglycéridémie et la cholestérolémie ont été mesurées à l’aide d’un kit commercial par spectrophotométrie. Le glutathion oxydé et réduit ont été mesurés par électrophorèse capillaire. Les relations linéaires obtenues sont exprimées par le ratio des carrés (r2), et traitées par ANOVA. Résultats : La validation du dosage de l’AscOOH par LC-MS a été réalisée. Chez les animaux, la concentration urinaire d’AscOOH par créatinine corrèle positivement avec la dose reçue, négativement avec la lipidémie, et négativement avec le redox sanguin et érythrocytaire, indiquant un milieu moins oxydé. Conclusion : La concentration urinaire d’AscOOH peut donc être un reflet de l’oxydation de l’HAIV en clinique. Nos données chez l’animal suggèrent une interaction de l’AscOOH avec le métabolisme hépatique produisant une chute de la concentration plasmatique de cholestérol et de triglycérides. Le modèle cellulaire n’a pas permis d’élucider le mécanisme moléculaire de l’action de l’AscOOH sur le métabolisme.