Operational Cost Reduction in WDM Networks using Lighttours

Wavelength division multiplexing (WDM) networks have been adopted as a near-future solution for the broadband Internet. In previous work we proposed a new architecture, named enhanced grooming (G+), that extends the capabilities of traditional optical routes (lightpaths). In this paper, we compare the operational expenditures incurred by routing a set of demands using lightpaths with that of lighttours. The comparison is done by solving an integer linear programming (ILP) problem based on a path formulation. Results show that, under the assumption of single-hop routing, almost 15% of the operational cost can be reduced with our architecture. In multi-hop routing the operation cost is reduced in 7.1% and at the same time the ratio of operational cost to number of optical-electro-optical conversions is reduced for our architecture. This means that ISPs could provide the same satisfaction in terms of delay to the end-user with a lower investment in the network architecture

All-Optical Unicast/Multicast Routing in WDM Networks

Optical transport networks (OTN) must be prepared in terms of better resource utilization, for accommodating unicast and multicast traffic together. Light-trees have been proposed for supporting multicast connections in OTN. Nevertheless when traffic grooming is applied in light-trees, resources can be underutilized as traffic can be routed to undesirable destinations in order to avoid optical-electrical-optical (OEO) conversions. In this paper, a novel architecture named S/G light- tree for supporting unicast/multicast connections is proposed. The architecture allows traffic dropping and aggregation in different wavelengths without performing OEO conversions. A heuristic that routes traffic demands using less wavelengths by taking advantage of the proposed architecture is designed as well. Simulation results show that the architecture can minimize the number of used wavelengths and OEO conversions when compared to light-trees

G+: Enhanced Traffic Grooming in WDM Mesh Networks using Lighttours

In this article, a new technique for grooming low-speed traffic demands into high-speed optical routes is proposed. This enhancement allows a transparent wavelength-routing switch (WRS) to aggregate traffic en route over existing optical routes without incurring expensive optical-electrical-optical (OEO) conversions. This implies that: a) an optical route may be considered as having more than one ingress node (all inline) and, b) traffic demands can partially use optical routes to reach their destination. The proposed optical routes are named "lighttours" since the traffic originating from different sources can be forwarded together in a single optical route, i.e., as taking a "tour" over different sources towards the same destination. The possibility of creating lighttours is the consequence of a novel WRS architecture proposed in this article, named "enhanced grooming" (G+). The ability to groom more traffic in the middle of a lighttour is achieved with the support of a simple optical device named lambda-monitor (previously introduced in the RingO project). In this article, we present the new WRS architecture and its advantages. To compare the advantages of lighttours with respect to classical lightpaths, an integer linear programming (ILP) model is proposed for the well-known multilayer problem: traffic grooming, routing and wavelength assignment The ILP model may be used for several objectives. However, this article focuses on two objectives: maximizing the network throughput, and minimizing the number of optical-electro-optical conversions used. Experiments show that G+ can route all the traffic using only half of the total OEO conversions needed by classical grooming. An heuristic is also proposed, aiming at achieving near optimal results in polynomial time

Adding new components to the knowledge plane GMPLS over WDM networks

A recent study defines a new network plane: the knowledge plane. The incorporation of the knowledge plane over the network allows having more accurate information of the current and future network states. In this paper, the introduction and management of the network reliability information in the knowledge plane is proposed in order to improve the quality of service with protection routing algorithms in GMPLS over WDM networks. Different experiments prove the efficiency and scalability of the proposed scheme in terms of the percentage of resources used to protect the network

Multi-layer survivability: routing schemes for GMPLS-based networks

En les xarxes IP/MPLS sobre WDM on es transporta gran quantitat d'informacio, la capacitat de garantir que el trafic arriba al node de desti ha esdevingut un problema important, ja que la fallada d'un element de la xarxa pot resultar en una gran quantitat d'informacio perduda. Per garantir que el trafic afectat per una fallada arribi al node desti, s'han definit nous algoritmes d'encaminament que incorporen el coneixement de la proteccio en els dues capes: l'optica (WDM) i la basada en paquets (IP/MPLS). D'aquesta manera s'evita reservar recursos per protegir el trafic a les dues capes. Els nous algoritmes resulten en millor us dels recursos de la xarxa, ofereixen rapid temps de recuperacio, eviten la duplicacio de recursos i disminueixen el numero de conversions del trafic de senyal optica a electrica.

A relative path attenuation approximation algorithm for DVB-T systems

In the United Kingdom and in fact throughout Europe, the chosen standard for digital terrestrial television is the European Telecommunications Standards Institute (ETSI) ETN 300 744 also known as Digital Video Broadcasting - Terrestrial (DVB-T). The modulation method under this standard was chosen to be Orthogonal Frequency Division Multiplex (0FD4 because of the apparent inherent capability for withstanding the effects of multipath. Within the DVB-T standard, the addition of pilot tones was included that can be used for many applications such as channel impulse response estimation or local oscillator phase and frequency offset estimation. This paper demonstrates a technique for an estimation of the relative path attenuation of a single multipath signal that can be used as a simple firmware update for a commercial set-top box. This technique can be used to help eliminate the effects of multipath(1).

Deterministic equalization and results of a DVB-T multipath equalizer for both 16-QAM and 64-QAM operation

Recent developments in the UK concerning the reception of Digital Terrestrial Television (DTT) have indicated that, as it currently stands, DVB-T receivers may not be sufficient to maintain adequate quality of digital picture information to the consumer. There are many possible reasons why such large errors are being introduced into the system preventing reception failure. It has been suggested that one possibility is that the assumptions concerning the immunity to multipath that Coded Orthogonal Frequency Division Multiplex (COFDM) is expected to have, may not be entirely accurate. Previous research has shown that multipath can indeed have an impact on a DVB-T receiver performance. In the UK, proposals have been made to change the modulation from 64-QAM to 16-QAM to improve the immunity to multipath, but this paper demonstrates that the 16-QAM performance may again not be sufficient. To this end, this paper presents a deterministic approach to equalization such that a 64-QAM receiver with the simple equalizer presented in this paper has the same order of MPEG-2 BER performance as that to a 16-QAM receiver without equalization. Thus, alleviating the requirement in the broadcasters to migrate from 64-QAM to 16-QAM Of course, by adding the equalizer to a 16-QAM receiver then the BER is also further improved and thus creating one more step to satisfying the consumers(1).

Analysis of the four wave mixing effect (FWM) in a dispersion decreasing fiber (DDF) for a WDM system

We did a numerical investigation of the propagation of short light pulses in the region of 1.55 mu m and the conversion efficiency (CE) for the four wave mixing generation (FWM) of ordinary and dispersion decreasing fibers for use in wavelength division multiplexing (WDM) systems, Our simulations studies three different profiles, linear, hyperbolic. and constant, One conclude that for all the profiles there is decrease of the conversion efficiency with the increase in the channel separation. The hyperbolic profile present a higher efficiency of around 1000 above in magnitude compared with the others profiles at 0.2 nm of channel separation. We calculate the conversion efficiency versus the fiber length for the three profiles. The conversion efficiency for the hyperbolic profile is higher when compared to the constant and linear profiles. The other interesting point of the hyperbolic profile is that the increase of the CE in the beginning of the fiber does not show my oscillation in the CE value (log eta), which was observed for the constant and linear profiles. For all the profiles there is an increase of the conversion efficiency with the increase of the pump power. The compression factor C-i for the generated FWM signal at omega(3) was measured along the DDF's and the constant profile fibers. One can conclude that with the use of decreasing dispersion profile (DDF) fibers one can have a control of the (CE) conversion efficiency and the compression factor of the four wave mixing (FWM) generation in WDM systems. (c) 2005 Elsevier B.V. All rights reserved.

Interaction of pulses in the nonlinear Schrödinger model

A study was conducted on the interaction of two pulses in the nonlinear Schrodinger (NLS) model. The presence of different scenarios of the behavior depending on the initial parameters of the pulses, such as the pulse areas, the relative phase shift, the spatial and frequency separations were shown. It was observed that a pure real initial condition of the NLS equation can result in additional moving solitons.

Sol-Gel Erbium-Doped Silica-Hafnia Planar and Channel Waveguides

Erbium activated SiO2 -HfO2 planar waveguides, doped with Er3+ concentrations ranging from 0.01 to 4 mol%, were prepared by sol-gel method. The films were deposited on v-SiO2 and silica-on-silicon substrates using dip-coating technique. The waveguides show high densification degree, effective intermingling of the two film components, and uniform surface morphology. The waveguide deposited on silica-on-silicon substrates shows one single propagation mode at 1.5μm, with a confinement coefficient of 0.81 and an attenuation coefficient of 0.8 dB/cm at 632.8nm. Emission in the C-telecommunication band was observed at room temperature for all the samples upon continuouswave excitation at 980 nm or 514.5 nm. The shape of the emission band corresponding to the 4I13/2 → 4I15/2 transition is found to be almost independent both on erbium content and excitation wavelength, with a FWHM between 44 and 48 nm. The 4I13/2 level decay curves presented a single-exponential profile, with a lifetime ranging between 1.1 - 6.6 ms, depending on the erbium concentration. Infrared to visible upconversion luminescence upon continuous-wave excitation at 980 nm was observed for all the samples. Channel waveguide in rib configuration was obtained by etching the active film in order to have a well confined mode at 1.5 μm.

Avaliação de desempenho de algoritmos de alocação de comprimento de onda em redes ópticas WDM

Neste trabalho estudamos alguns algoritmos de alocação de comprimento de onda em redes ópticas WDM (Wavelength Division Multiplexing). O objetivo para estudar os algoritmos de alocação first-fit, least-used e most-used está baseado na estratégia adotada para estudar o Problema RWA. A estratégia toma como base a visão geral do problema que envolve os algoritmos de roteamento e os algoritmos de alocação de comprimento de onda, e tendo como métrica principal para seus resultados a probabilidade de bloqueio. Este trabalho apresenta uma visão diferenciada para o problema e considera-se que a alocação de comprimentos de onda se sobrepõe, em importância, à ação de roteamento em redes ópticas. Essa percepção ocorre quando se analisa o problema RWA a partir do critério clássico usado no estabelecimento de uma rota: a escolha do caminho mais curto entre a origem e o destino. Apesar da identificação de um caminho mais curto, isso não garante, em redes ópticas, que ele será o utilizado, pois é necessário que haja para aquele caminho, um comprimento de onda adequado. Foi utilizada uma ferramenta de simulação para redes WDM denominada OWNS para realizar uma análise do problema RWA. Os resultados obtidos são apresentados graficamente e em uma das simulações observou-se uma forte tendência de queda na probabilidade de bloqueio e uma boa vazão no trafego da rede com isso possibilitando um aumento na capacidade de transmissão da rede. Por fim, este texto apresenta uma discussão sobre os diferenciais e limitações deste trabalho, e apresenta direcionamentos para investigações futuras neste campo de estudo.

Estratégia de projeto de atribuição de comprimento de onda com restrição de camada física em redes WDM

O sistema WDM (Wavelength Division Multiplexing) é considerado como uma tecnologia madura para ser usada no backbone de redes ópticas. Entretanto, encontrar uma solução ótima para o algoritmo de atribuição de comprimento de onda no projeto e operação destas redes, ainda é uma questão em aberto. A pesquisa realizada nesta tese aborda os principais aspectos relacionados ao processo de atribuição de comprimento de onda em sistemas WDM, e como resultado foi proposta uma metodologia que minimiza a degradação do sinal óptico gerada pela modulação de fase cruzada (XPM – Cross-Phase Modulation). Esta proposta é composta por uma metodologia híbrida baseada em Coloração de Grafo e Algoritmo Genético (AG), sendo que o primeiro tem a função de reduzir o número de comprimentos de onda necessários para atender a matriz de tráfego (que é fornecida a priori) e o último tem a função de encontrar a ordem de ativação de canais na grade de comprimentos de onda, com o objetivo de reduzir o efeito XPM. A proposta foi comparada com o algoritmo First-Fit em diferentes cenários e topologias de redes, e demonstrou uma considerável redução na probabilidade de bloqueio.

Estudo comparativo de sistemas de rádio digital sobre fibra aplicado a C-RAN

O objetivo deste trabalho é comparar aspectos relacionados ao uso de Multiplexação por Subportadora (SCM) em um sistema de transmissão de Rádio Digital sobre Fibra (DRoF) aplicado à Arquitetura de Acesso a Rádio Centralizado (C-RAN). Para isso, foram criados dois cenários que fazem uso da tecnologia DRoF, onde no primeiro, três subportadoras são transmitidas em um comprimento de onda e, para o segundo cenário, três comprimentos de onda são transmitidos, onde cada um possui uma única subportadora. Para ambas configurações é visado alimentar unidades de rádio remoto (RRH) localizadas na torre de transmissão. São analisados aspectos de desempenho da recepção, alcance das redes e complexidade do sistema para cada um dos cenários propostos. Além disso, são mostrados passo a passo como os sistemas foram construídos utilizando o software de simulação VPITransmissionMaker. Foram considerados para cada subportadora uma taxa de 250 Mbps, modulação 16-QAM, centrados na frequência de 5GHz. Os resultados obtidos demonstram que, para SCM-DRoF, uma Taxa de Erro de Bit (BER) de 10^-6 é mantida constante para enlaces de até 20 km. No segundo modelo, sem uso de SCM, um desempenho similar foi verificado, contudo com alcance de até 40 km. Dado o contexto da aplicação, os fatores desempenho e distância levam a crer que ambos cenários de transmissão podem ser utilizadas para C-RAN. Contudo, levando em consideração o custo e a complexidade no domínio óptico, o sistema utilizando SCM, comparativamente, possui mais vantagens. Conclui-se então que o uso de SCM apresenta-se como uma forte opção para aplicações no contexto das novas tecnologias de redes de acesso móvel.

Políticas de alocação de espectro em roteamento baseado em balanceamento de cargas e fragmentação para redes ópticas elásticas

A natureza rígida de redes de multiplexação por divisão de comprimentos de onda (WDM) provoca exploração ineficiente de capacidade espectral. Dessa forma, redes flexíveis são um possível avanço para a tecnologia óptica por viabilizarem melhor aproveitamento dos recursos espectrais disponíveis. Com o intuito de aferir a possível aplicabilidade de redes flexíveis, este trabalho propõe uma estratégia de avaliação de desempenho baseada em simulações e comparações entre resultados obtidos. Para tanto, várias simulações a tempo discreto foram implementadas em dois simuladores desenvolvidos em Matlab a fim de analisar diferentes políticas de alocação de espectro (First-Fit, Smallest-Fit, Exact-Fit e Random-Fit) em três algoritmos de roteamento por caminhos ópticos não híbridos: o roteamento por fragmentação externa (FA), por caminhos mais curtos com máxima eficiência de reuso espectral (SPSR) e por balanceamento de cargas (BLSA). Duas topologias de rede foram utilizadas: um pequeno subconjunto de 6 nós da Cost239 e uma topologia aleatória de 7 nós. Admitindo-se que efeitos de camada física não foram configurados como restrições, foram realizadas comparações entre as diversas técnicas estudadas, objetivando-se apontar, baseado nas especificidades dos cenários propostos, qual o método mais adequado de alocação espectral em termos de frequência de bloqueio entre as quatro políticas de alocação de espectro consideradas.

Survivable Lightpath Provisioning in WDM Mesh Networks Under Shared Path Protection and Signal Quality Constraints

This paper addresses the problem of survivable lightpath provisioning in wavelength-division-multiplexing (WDM) mesh networks, taking into consideration optical-layer protection and some realistic optical signal quality constraints. The investigated networks use sparsely placed optical–electrical–optical (O/E/O) modules for regeneration and wavelength conversion. Given a fixed network topology with a number of sparsely placed O/E/O modules and a set of connection requests, a pair of link-disjoint lightpaths is established for each connection. Due to physical impairments and wavelength continuity, both the working and protection lightpaths need to be regenerated at some intermediate nodes to overcome signal quality degradation and wavelength contention. In the present paper, resource-efficient provisioning solutions are achieved with the objective of maximizing resource sharing. The authors propose a resource-sharing scheme that supports three kinds of resource-sharing scenarios, including a conventional wavelength-link sharing scenario, which shares wavelength links between protection lightpaths, and two new scenarios, which share O/E/O modules between protection lightpaths and between working and protection lightpaths. An integer linear programming (ILP)-based solution approach is used to find optimal solutions. The authors also propose a local optimization heuristic approach and a tabu search heuristic approach to solve this problem for real-world, large mesh networks. Numerical results show that our solution approaches work well under a variety of network settings and achieves a high level of resource-sharing rates (over 60% for O/E/O modules and over 30% for wavelength links), which translate into great savings in network costs.