Report on Rest Area Water Systems for Interstate Highways, 1967

Introduction: As part of the roadside development along the Interstate Highway System, the Iowa State Highway Commission has constructed eight pair of rest area facilities. Furthermore, two pair are presently under construction with an additional two pair proposed for letting in 1967. An additional nine and one-half pairs of rest areas are in the planning phase, a grand total of 45 rest Brea buildings. The facilities existing were planned and designed in a relatively short period of time. The rest area facilities are unusual in terms of water use, water demand rates, and the fact that there are no applicable guidelines from previous installations. Such facilities are a pioneering effort to furnish a service -which the travelling public desires and will use. The acceptance and current use of the existing facilities shows that the rest areas do provide a service the public will use and appreciate. The Iowa State Highway Commission is to be congratulated for this· pioneering effort. However there are problems, as should be expected when design of a new type of facility has no past operating experience to use as a guide. Another factor which enters is that a rest area facility is quite different and rather unrelated to engineering in the highway field of practice. Basically, the problems encountered can be resolved into several areas, namely 1) maintenance problems in equipment due to 2) insufficient capacity of several other elements of the water systems, and 3) no provisions for water quality control. This study and report is supposed to essentially cover the review of the rest areas, either existing and under construction or letting. However, the approach used has been somewhat different. Several basic economically feasible water system schemes have been developed which are· adaptable to the different well capacities and different water qualities encountered. These basic designs are used as a guide in recommending modifications to the existing rest area water systems, anticipating that the basic designs will be used for future facilities. The magnitude of the problems involved is shown by the fact that the projected water use and demand variations of each rest area building is equivalent to the water supply for a community of about 100 people. The problems of proper operation and maintenance of an eventual thirty to forty-five such facilities are gigantic. For successful operation the rest area water systems must have a high degree of standardization and interchangeability of all elements of the water systems, even if it means a limited degree of over-design in some rest area facilities.

Upgrading of thethird generation of the Remote Diagnostic Systems for ABB Marine Propulsion Systems

Remote diagnostics has become very popular in marine industry. Diagnostic systems are improved all the time and the newest monitoring systems are constantly taken into operation. Most vessels are, however, rigged up by outmoded facilities, which should be updated. In this work the principles of operating of such a remote diagnostic system as the ABB's third generation remote diagnostic system (RDS) and the newest Propulsion Condition Management System (PCMS) are studied. As a result of the thesis the ways of upgrading the old systems of RDS are presented. Specifically, the work focuses on the establishment of the connection between Advant controller AC-110 from the old system and PCMS server, and in other words how to get Modbus data by OPC server.

Relative Technical Efficiency of European Transportation Systems

Talouden kasvaessa myös tavarankuljetusmäärät kasvavat. Kuljetusjärjestelmät ja niiden sujuva toiminta on erittäin tärkeää taloudellisen kasvun kannalta tällä hetkellä, ja se tulee olemaan yhä tärkeämpää tulevaisuudessa. Tulevaisuudessa tarvitaan kokonaisvaltainen ja selkeästi tehokkaampi kuljetusjärjestelmä, mikäli tulevaisuuden kuljetusvirrat halutaan hoitaa kestävästi. Tässä opinnäytetyössäni tutkin kolmen eurooppalaisen kuljetusjärjestelmän (rautatiet, lentoliikenne ja konttiliikenne meritse) suhteellista teknistä tehokkuutta ja menetelmänä on data envelopment analysis (DEA). Vertailtaessa kuljetusjärjestelmiä löytyi suuria eroja kuljetusmuotojen välille. lentoyhtiöt suoriutuivat huomattavan tasaisesti eli tehokkaiden ja ei-tehokkaiden toimijoiden välillä ei ollut suuria eroja. Rautatiepuolella erot venyivät huomattavan suuriksi niin eri yritysten välillä kuin jopa saman yrityksen sisällä eri vuosina. Pikaisemmassa laivayhtiöiden tarkastelussa erot niiden välillä olivat lähes yhtä pieniä kuin lentoyhtiöiden välillä. Tarkasteltaessa omistajuuden vaikutusta lentoyhtiöiden toiminnassa huomattiin, että yksityisessä omistuksessa olevat yritykset olivat huomattavasti tehokkaampia matkustajien kuljettamisessa. Rahtipuolella merkittäviä eroja ei havaittu. Merkittävät korrelaatiot eri mallien välillä antoivat joitain viitteitä myös kuljetuspoliittiseen päätöksentekoon; investoinnit matkustajienkuljetuksiin raiteilla parantaisivat koko rautatiepuolen teokkuutta, mutta myös samalla lentopuolen matkustajakuljetuksen tehokkuutta.

Performance Tuning of Fenix Logistic Systems

Työn tavoitteena oli selvittää Stora Enso Oyj:llä käytössä olevan Fenix myynnin- ja logistiikanhallintajärjestelmän logistiikkapalveluiden suorituskyky, tuottaa asiakasohjelmisto suorituskykymittauksista muodostuneen tiedon hallintaan sekä tuottaa toteuttamissuunnitelma suorituskyvyn parantamiseksi. Suorituskyky mitattiin käyttämällä TUXEDOn tarjoamia ominaisuuksia. Suorituskykymittausten tuloksien arviointia varten rakennettiin asiakasohjelmisto, jolla pystyttiin tuottamaan tarvittavat yhteenvetotiedot palveluiden kestoista ja rakenteista. Valmiita ratkaisuja ei ollut tarjolla, joten kaikki tarvittavat ohjelmistot on rakennettu osana tätä työtä. Kaikki komponenttiliittymät toteutettiin siten, että myös muitakin kuin logistiikkaan liittyviä palveluita voidaan tarvittaessa mitata. Mittausten tuloksena saatuja keskimääräisiä suoritusaikoja käytettiin hyväksi toteuttamissuunnitelmaa tehdessä. Toteutussuunnitelma sisältää useiden logistiikka-alueiden kehittämisideoita, joilla Fenixin logistiikkapalveluiden suorituskykyä voidaan tehostaa., ja nykyinen järjestelmän toimintanopeus pystytään säilyttämään tulevaisuudessa. Toteuttamissuunnitelmassa esitettyjä toimenpiteitä tullaan toteuttamaan TietoEnator Oyj:ssä vuoden 2003 aikana.

Protocol Specific Embedded Operating System

Sulautettujen järjestelmien määrä kuten niiden sisältämä älykkyyskin ovat viime vuosina kasvaneet merkittävästi. Sulautettujen ohjelmistojen yleistymistä ja monipuolistumista on edesauttanut sulautettujen laitteistojen prosessointitehon merkittävä kehittyminen, jonka myötä entistä vaativampien ohjelmistojen totetuttaminen sulautetusti on mahdollistunut. Seuraavana sulautettujen järjestelmien kehitysaskeleena on nähtävissä järjestelmien kommunikointikyvyn paraneminen ja siten uusien ja uudentyyppisten sulautettujen ratkaisujen toteuttaminen. VTT on päättänyt tutkia sulautettujen järjestelmien kommunikointia ja kehittää sulautettun protokolla-alustan. Tutkimuksen perusta on CVOPS protokollajärjestelmä, jota jatkokehittämällä pyritään toteuttamaan sulautettu protokollajärjestelmä, µCVOPS. Tässä diplomityössä esitetään kommunikaation sulautetulle järjestelmälle asettamia vaatimuksia, järjestelmän suunnittelu ja prototyypitys sulautetulla laitteistolla. Prototyypitykseen on käytetty sulautettua DragonBall mikrokontrolleria jonka käyttöjärjestelmänä käytettiin sulautettua Linux:a. Tälle alustalle on tehty CVOPS:sta modifioitu versio, jolla µCVOPS:ia pystytään simuloimaan.

Filtration of effluents for microirrigation systems

Clogging, measured through head loss across filters, and the filtration quality of different filters using different effluents were studied. The filters used were: 115, 130, and 200 m disc filters; 98, 115, 130, and 178 m screen filters; and a sand filter filled with a single layer of sand with an effective diameter of 0.65 mm. The filters were used with a meat industry effluent and secondary and tertiary effluents of two wastewater treatment plants. It was observed that clogging depended on the type of effluent. With the meat industry effluent, the poorest quality effluent, disc filters clogged more than the other filter types. When the wastewater treatment plant effluents were used, the disc filters showed less frequent clogging. Several physical and chemical parameters, such as total suspended solids, chemical oxygen demand, turbidity, electrical conductivity, pH, and number of particles, were analyzed in the effluents at the entry and exit points of the filters. In general, filters did not reduce the values of the main clogging parameters to a great degree. It was found that the parameter that explained the clogging, expressed as Boucher’s filterability index, was different depending on the type of effluent and filter. The best quality of filtration was achieved with a sand filter when the meat industry effluent was used. No significant differences were observed between the quality of filtration of disc and screen filters when operating with the secondary and tertiary effluents

Dustiness and deagglomeration testing: interlaboratory comparison of systems for nanoparticle powders

Different types of aerosolization and deagglomeration testing systems exist for studying the properties of nanomaterial powders and their aerosols. However, results are dependent on the specific methods used. In order to have well-characterized aerosols, we require a better understanding of how system parameters and testing conditions influence the properties of the aerosols generated. In the present study, four experimental setups delivering different aerosolization energies were used to test the resultant aerosols of two distinct nanomaterials (hydrophobic and hydrophilic TiO2). The reproducibility of results within each system was good. However, the number concentrations and size distributions of the aerosols created varied across the four systems; for number concentrations, e.g., from 10(3) to 10(6) #/cm(3). Moreover, distinct differences were also observed between the two materials with different surface coatings. The article discusses how system characteristics and other pertinent conditions modify the test results. We propose using air velocity as a suitable proxy for estimating energy input levels in aerosolization systems. The information derived from this work will be especially useful for establishing standard operating procedures for testing nanopowders, as well as for estimating their release rates under different energy input conditions, which is relevant for occupational exposure.

Managing the Front End of Innovation in a Networked Company Environment - Combining Strategy, Processes and Systems of Innovation

The objective of the thesis is to enhance the understanding about the management of the front end phases of the innovation process in a networked environment. The thesis approaches the front end of innovation from three perspectives, including the strategy, processes and systems of innovation. The purpose of the use of different perspectives in the thesis is that of providing an extensive systemic view of the front end, and uncovering the complex nature of innovation management. The context of the research is the networked operating environment of firms. The unit of analysis is the firm itself or its innovation processes, which means that this research approaches the innovation networks from the point of view of a firm. The strategy perspective of the thesis emphasises the importance of purposeful innovation management, the innovation strategy of firms. The role of innovation processes is critical in carrying out innovation strategies in practice, supporting the development of organizational routines for innovation, and driving the strategic renewal of companies. The primary focus of the thesis from systems perspective is on idea management systems, which are defined as a part of innovation management systems, and defined for this thesis as any working combination of methodology and tools (manual or IT-supported) that enhance the management of innovations within their early phases. The main contribution of the thesis are the managerial frameworks developed for managing the front end of innovation, which purposefully “wire” the front end of innovation into the strategy and business processes of a firm. The thesis contributes to modern innovation management by connecting the internal and external collaboration networks as foundational elements for successful management of the early phases of innovation processes in a dynamic environment. The innovation capability of a firm is largely defined by its ability to rely on and make use of internal and external collaboration already during the front end activities, which by definition include opportunity identification and analysis, idea generation, profileration and selection, and concept definition. More specifically, coordination of the interfaces between these activities, and between the internal and external innovation environments of a firm is emphasised. The role of information systems, in particular idea management systems, is to support and delineate the innovation-oriented behaviour and interaction of individuals and organizations during front end activities. The findings and frameworks developed in the thesis can be used by companies for purposeful promotion of their front end processes. The thesis provides a systemic strategy framework for managing the front end of innovation – not as a separate process, but as an elemental bundle ofactivities that is closely linked to the overall innovation process and strategy of a firm in a distributed environment. The theoretical contribution of the thesis relies on the advancement of the open innovation paradigm in the strategic context of a firm within its internal and external innovation environments. This thesis applies the constructive research approach and case study methodology to provide theoretically significant results, which are also practically beneficial.

Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Comparative analysis of different meat traceability systems using multiple criteria and a social network approach

The adoption of a proper traceability system is being incorporated into meat production practices as a method of gaining consumer confidence. The various partners operating in the chain of meat production can be considered a social network, and they have the common goal of generating a communication process that can ensure each characteristic of the product, including safety. This study aimed to select the most appropriate meat traceability system “from farm to fork” that could be applied to Brazilian beef and pork production for international trade. The research was done in three steps. The first used the analytical hierarchy process (AHP) for selecting the best on-farm livestock traceability. In the second step, the actors in the meat production chain were identified to build a framework and defined each role in the network. In the third step, the selection of the traceability system was done. Results indicated that with an electronic traceability system, it is possible to acquire better connections between the links in the chain and to provide the means for managing uncertainties by creating structures that facilitate information flow more efficiently.

Spraying systems and traveling speed in the deposit and spectrum of droplets in cotton plant

ABSTRACT Tractor traveling speed can influence the quality of spraying depending on the application technology used. This study aimed to evaluate the droplet spectrum, the deposition and uniformity of spray distribution with different spraying systems and traveling speeds of a self-propelled sprayer in two phenological stages of the cotton plant (B9 and F13). The experimental design was randomized blocks and treatments were three spraying techniques: common flat spray tips; tilted flat jet with air induction, at 120 L ha-1; and rotary atomizer disk, 20 L ha-1, combined with four traveling speeds: 12, 15, 18 and 25 km h-1, with four replications. Spraying deposition was evaluated for both leaf surfaces from the cotton plant apex and base (stage B9) and middle part of the plant (stage F13) with a cupric marker. A laser particle analyzer also assessed the droplet spectrum. The centrifugal power spray system produces more homogeneous droplet spectrum and increased penetration of droplets into the canopy in both phenological stages. Variation on the operating conditions necessary for increased traveling speed negatively influences the pattern of spraying deposits.

E-PORT. Improving efficiency of Finnish port community by intelligent systems Final report of the Mobile Port project

The management of port-related supply chains is challenging due to the complex and heterogeneous operations of the ports with several actors and processes. That is why the importance of information sharing is emphasised in the ports. However, the information exchange between different port-related actors is often cumbersome and it still involves a lot of manual work and paper. Major ports and port-related actors usually have advanced information systems in daily use but these systems are seldom interoperable with each other, which prevents economies of scale to be reached. Smaller ports and companies might not be equipped with electronic data transmission at all. This is the final report of the Mobile port (MOPO) project, which has sought ways to improve the management and control of port-related sea and inland traffic with the aid of ICT technologies. The project has studied port community systems (PCS) used worldwide, evaluated the suitability of a PCS for the Finnish port operating environment and created a pilot solution of a Finnish PCS in the port of HaminaKotka. Further, the dry port concept and its influences on the transportation system have been explored. The Mobile Port project comprised of several literature reviews, interviews of over 50 port-related logistics and/or ICT professionals, two different kinds of simulation models as well as designing and implementing of the pilot solution of the Finnish PCS. The results of these multiple studies are summarised in this report. Furthermore, recommendations for future actions and the topics for further studies are addressed in the report. The study revealed that the information sharing in a typical Finnish port-related supply chain contains several bottlenecks that cause delays in shipments and waste resources. The study showed that many of these bottlenecks could be solved by building a port community system for the Finnish port community. Almost 30 different kinds of potential services or service entities of a Finnish PCS were found out during the study. The basic requirements, structure, interfaces and operation model of the Finnish PCS were also defined in the study. On the basis of the results of the study, a pilot solution of the Finnish PCS was implemented in the port of HaminaKotka. The pilot solution includes a Portconnect portal for the Finnish port community system (available at https://www.portconnect.fi) and two pilot applications, which are a service for handling the information flows concerning the movements of railway wagons and a service for handling the information flows between Finnish ports and Finland-Russian border. The study also showed that port community systems can be used to improve the environmental aspects of logistics in two different ways: 1) PCSs can bring direct environmental benefits and 2) PCSs can be used as an environmental tool in a port community. On the basis of the study, the development of the Finnish port community system should be continued by surveying other potential applications for the Finnish PCS. It is also important to study if there is need and resources to extend the Finnish PCS to operate in several ports or even on a national level. In the long run, it could be reasonable to clarify whether there would be possibilities to connect the Finnish PCS as a part of Baltic Sea wide, European-wide or even worldwide maritime and port-related network in order to get the best benefit from the system

Enhancing the development of military capabilities by a systems approach

The political environment of security and defence has changed radically in the Western industrialised world since the Cold War. As a response to these changes, since the beginning of the twenty-first century, most Western countries have adopted a ‘capabilities-based approach’ to developing and operating their armed forces. More responsive and versatile military capabilities must be developed to meet the contemporary challenges. The systems approach is seen as a beneficial means of overcoming traps in resolving complex real -world issues by conventional thinking. The main objectives of this dissertation are to explore and assess the means to enhance the development of military capabilities both in concept development and experimentation (CD&E) and in national defence materiel collaboration issues. This research provides a unique perspective, a systems approach, to the development areas of concern in resolving complex real-world issues. This dissertation seeks to increase the understanding of the military capability concept both as a whole and with in its life cycle. The dissertation follows the generic functionalist systems methodology by Jackson. The methodology applies a comprehensive set of constitutive rules to examine the research objectives. This dissertation makes contribution to current studies about military capability. It presents two interdepen dent conceptual capability models: the comprehensive capability meta-model (CCMM) and the holistic capability life cycle model (HCLCM). These models holistically and systematically complement the existing, but still evolving, understanding of military capability and its life cycle. In addition, this dissertation contributes to the scientific discussion of defence procurement in its broad meaning by introducing the holistic model about the national defence materiel collaboration between the defence forces, defence industry and academia. The model connects the key collaborative mechanisms, which currently work in isolation from each other, and take into consideration the unique needs of each partner. This dissertation contributes empirical evidence regarding the benefits of enterprise architectures (EA) to CD&E. The EA approach may add value to traditional concept development by increasing the clarity, consistency and completeness of the concept. The most important use considered for EA in CD&E is that it enables further utilisation of the concept created in the case project.

Project Management Tools in Agile Embedded Systems Development

Agile methods have become increasingly popular in the field of software engineering. While agile methods are now generally considered applicable to software projects of many different kinds, they have not been widely adopted in embedded systems development. This is partly due to the natural constraints that are present in embedded systems development (e.g. hardware–software interdependencies) that challenge the utilization of agile values, principles and practices. The research in agile embedded systems development has been very limited, and this thesis tackles an even less researched theme related to it: the suitability of different project management tools in agile embedded systems development. The thesis covers the basic aspects of many different agile tool types from physical tools, such as task boards and cards, to web-based agile tools that offer all-round solutions for application lifecycle management. In addition to these two extremities, there is also a wide range of lighter agile tools that focus on the core agile practices, such as backlog management. Also other non-agile tools, such as bug trackers, can be used to support agile development, for instance, with plug-ins. To investigate the special tool requirements in agile embedded development, the author observed tool related issues and solutions in a case study involving three different companies operating in the field of embedded systems development. All three companies had a distinct situation in the beginning of the case and thus the tool solutions varied from a backlog spreadsheet built from scratch to plug-in development for an already existing agile software tool. Detailed reports are presented of all three tool cases. Based on the knowledge gathered from agile tools and the case study experiences, it is concluded that there are tool related issues in the pilot phase, such as backlog management and user motivation. These can be overcome in various ways epending on the type of a team in question. Finally, five principles are formed to give guidelines for tool selection and usage in agile embedded systems development.